Search Documents

By Y. Shu, A. R. Laplante

"A laboratory Knelson Concentrator (LKC), 7.5 cm in diameter, was used to study the performance of a similar unit at plant scale, 76 cm in diameter, This paper reports on sampling and assaying procedures and problems, and discusses the performance of the plant unit.The sampling procedure was based on the extraction of large samples, 5-15 kg, and their complete processing with a LKC, to characterize size-by-size performance. The procedure yielded reliable estimates of overall gold assays, after blatant assaying errors were corrected. The plant centrifugal unit concentrate was sampled in situ, which yielded very erratic grades, with a large overall negative bias. Due to the very heterogeneous nature of the concentrate, which can be linked to flow patterns in the riffles of the unit, it is recommended that for future testwork, the concentrate be recovered separately, blended and then sampled.The plant centrifugal separator, when operated at a feed rate of 25 t/h, yielded total and free gold recoveries of 41 % and 62%, respectively. This is much lower than previously reported data, and suggest that at 25 t/h, the unit is overloaded. However, recovery did not decrease with time over a loading cycle of 2 hours, which suggests that present loading cycles, generally 1 hour, can be significantly increased. INTRODUCTIONThe study of gold gravity circuits is plagued with the statistical problem of determining the behaviour of particles occurring with a very low frequency. This problem becomes particularly acute with increasing particle size. For example, considering the average weight of a gold flake in the 840-1200 µm (20/28 mesh) to be about 5 mg (Banisi et al, 1991), a reasonably high grade feed of 10 git would require, for a relative error (standard deviation) of 10% on grade, 100 particles, that is 0.5 g of gold, or 50 kg of 840-1200 µm material (a Poisson distribution is assumed). Gy's formula, for the same data, yields a weight of 33 kg, with a shape factor of 0.1 and a size distribution factor of 0.5. Both results are comparable; to obtain the suggested weight of material, a stream containing 5% weight in the 840-1200 µm would require 1 tonne samples (of unsized material). The problem rapidly disappears with decreasing particle size. Still with Banisi et al's data, a gold flake in the 300-420 µm range averages 0.5 mg in weight; the same 10% error on grade corresponds to a weight of 5 kg. Gy's formula for the same size distribution and particle shape factors as above predicts a required mass of 1.4 kg. This would correspond to an unsized sample weight of 10 kg with 14% weight in the 300-420 µm, for example."

Jan 1, 1992

By J. Muralha, L. Lamas

"Given the results of triaixial tests, regressions are commonly used to evaluate the parameters of failure criteria that model intact rock strength and to perform statistical inferences used to evaluate characteristic values defined in EC7. Statistical robustness of these inferences is affected if the basic hypothesis underlying regression are not met, namely homoscedasticity (constant variance of the errors). This paper presents analyses of 23 sets of triaxial tests, starting by the evaluation of the regression parameters of the Mohr-Coulomb linear criterion and of the Hoek-Brown non-linear criterion, followed by carrying several statistical tests to check the homoscedasticity null hypothesis of independence between the variance of intact rock strength and the confining stress.INTRODUCTIONThough rock engineering design is clearly included in the scope of Eurocode 7(EN1997-1), its implementation raised a wide discussion regarding the applicability of structural safety concepts to geotechnical design of construction works in or on rock masses. The basis of the limit state design philosophy adopted in EC7 is that, for each particular design situation, all the possible limit states for a structure, or part of it, shall be considered and that it shall be demonstrated that the likelihood of any limit state being exceeded is sufficiently small. Though EC7 allows the limit states to be verified by one or a combination of methods, use of calculations is by far the most used, and it is often confused with the EC7 itself. It involves using characteristic values of actions, ground properties and geometrical data, as well as obtaining their design values by the partial factor method.Characteristic value of a given material property is defined in Eurocode (EN 1990) as: “value of a material or product property having a prescribed probability of not being attained in a hypothetical unlimited test series. This value generally corresponds to a specified fractile of the assumed statistical distribution of the particular property of the material or product”. As regards the design value of a material or product property, according to the Eurocode it is a “value obtained by dividing the characteristic value by a partial factor”."

Jan 1, 2015

By S. Shokri

The increasing size and complexity of mega construction projects result in having several geographically distributed stakeholders, collaborating with each other to successfully deliver the project. Electronic Product and Process Management Systems (EPPMS) are recently emerging to facilitate the collaboration between stakeholders, reduce the surprises and issues, and improve the project productivity. These are commercially successful but evolving systems. An important component of EPPMS is the Interface Management System, which aims at formalizing and automating the communication channels between stakeholders. An interface is generally considered the link between construction elements, phases, or stakeholders. An interface Management System (IMS) involves five iterative steps: (1) Interface Identification, (2) Interface Documentation, (3) Interface Transferring, (4) Interface Communication, and (5) Interface Closing. A fundamental part of step 2 is recognizing different roles in dealing with interfaces. Each stakeholder is assigned a different role, such as responsible, accountable, consulted, and informed. In a mega project, several thousands of interfaces exist with complex relationships between stakeholders. Therefore, identifying stakeholders with higher responsible roles has been requested as useful information to the project owner in dealing with some of the project risks. After the interfaces are determined, and the responsibilities are allocated, the critical stakeholders are identified using the centrality concept in Social Network Analysis. The critical stakeholders can be determined at the highest level, considering all types of interfaces, as well as for each specific type or discipline-related interfaces. The proposed methodology is applied on a hypothetical offshore project with over 500 interfaces. In fact, this project is a simplified representation of a real scale Liquid Natural Gas project. In order to reduce the complexity of calculations and clarity of explanations, the simplified case study is used. By implementing IMS in mega projects, different parties not only formalize the communication between each other, but also gain better visibility concerning their roles and responsibilities. In addition, the owner benefits from analysing the complex relationships between stakeholders to further identify critical ones, along with other criteria like package cost, stakeholders? experiences, etc.

Aug 1, 2013

By Steven W. Wilson, Brigitte Lacouture, Nichola A. McKay

"The Aqqaluk deposit is a lead-zinc ore body that lies immediately north of the Main Pit at Teck Cominco’s Red Dog Mine in Alaska. It is scheduled to begin production in 2011 or 2012. A project team was formed in late 2004 to plan and implement an ore characterisation and metallurgical evaluation on the Aqqaluk ore. The main objective of this program was to facilitate the transition from Main Pit to Aqqaluk ore in the Red Dog concentrator. The program will develop a detailed, spatially-oriented characterisation of the Aqqaluk deposit attributes including lithology, ore geochemistry, bulk mineralogy, ore texture, as well as evaluating the metallurgical characteristics of ore hardness, process water geochemistry, bench-scale floatability and mineral liberation in ground feed, concentrate and tails. Developing correlations between the metallurgical response and the ore characterisation data is key to the emerging science of geometallurgy. This on-going program is a technical due diligence study that aims to reduce the risk associated with processing a new ore and to provide predictive information for mining and stockpile preparation.The test work to date has focused on characterising the five ore zones currently identified in the Aqqaluk deposit, namely: Siliceous (sub-divided to High Zn:Fe and Low Zn:Fe), Vein, Median Plate and Baritic ores. It identified a number of challenges associated with surface oxidation, or weathering, of the core samples and outlined a program for future sample collection and storage. Metallurgical testing evaluated ore hardness by a variety of methods. Preliminary floatability studies have been completed and some initial links have been established between the ore characteristics and the flotation response. Soluble mineral weathering products, the relative abundance of pyrite and marcasite and the iron content in the sphalerite grains have all shown a correlation to mineral recovery.As new core is received, both the ore characterisation and the metallurgical testing will be continued with a view to strengthen the existing correlations and develop new links."

Jan 1, 2007

By C. A. Jeffrey, K. Pearson

Abstract - The Croft diorite in central England belongs to a suite of Caledonian igneous rocks collectively known as the South Leicestershire diorite complex. Although the intrusions occupy separate outcrops, they are linked at depth to form a single pluton, buried beneath a cover of Triassic sediments (Le Bas, 1972; 1982, Allsop and Arthur, 1983). Both the Caledonian diorites and the overlying sub-Triassic unconformity have been affected by a complex history of alteration and mineralization which can be subdivided into four stages: (1) deuteric effects, caused by the release of volatiles during magmatic cooling; (2) albitization through sodic enrichment; (3) formation of lowtemperature laumontite, analcime and calcite veins with associated wall-rock alteration to prehnite and pumpellyite; and (4) sub-Triassic unconformity-hosted base metal, manganese and palygorskite mineralization. Zeolite mineralization occured some 200 Ma later than the intrusion itself, during post-Triassic times, as indicated by the presence of a single vein of laumontite and microcrystalline calcite which cross-cuts the sub-Triassic unconformity surface and enters the overlying Triassic sediments. Evidence from fluid inclusion work indicates that two fluids were involved in the deposition of the zeolite veins. One fluid was initially of relatively high temperature (~100°C to 320°C) and low salinity (~0.2 to 5.9 wt% NaCl equiv.), and was probably meteoric in origin, whereas the other was of relatively low temperature (~41°C to 165°C) and high salinity (~0.4 to 16.72 wt% NaCl equiv.), and is interpreted to represent a basinal brine. During Triassic rifting, thinning and fracturing of the crust, with the possible rise of associated magmas (Halliday and Mitchell, 1984), could have increased permeability and heat flow, initiating the circulation of hydrothermal fluids. Triassic unconformity-hosted base-metal mineralization in Central England is similar to other Triassic-Jurassic mineralization in Europe (Mitchell and Halliday, 1976).

Jan 1, 1997

By W. G. Miller, J. D. Scott, D. C. Sego

ABSTRACT The influence of using different extraction processes (caustic versus non-caustic) on thethixotropic strength of oil sands fine tailings is examined, as is the influence of adding a coagulant tocaustic fine tailings. The thixotropic strength of fine tailings at large void ratios manifests itself as a bonding or gel strength that has been widely noted both in the laboratory and in the field. This gel strength has a significant influence on preventing the initial consolidation or settlement of fine tailings. Differences between the fine tailings’ thixotropic strength development are explained based on their physical and chemical characteristics.

Jan 1, 2010

By George W. Bain

The area in Quebec immediately north of the Ottawa river is underlain by a large area of granite gneiss intruded in lit-par-lit fashion into Grenville sediments and low silica intrusives of the Buckingham Series. This complex of metamorphic rocks is intruded by a much later magma found, chiefly, as a very large stock about 20 miles in diameter and extending from Brownsburg to Grenville, and as dykes and small outliers at various places adjacent to its outer margin. 1A similar stock at Rigaud, Quebec, is situated south of the Ottawa river and has been described by O. E. Le Roy. The earliest representatives of the later magma are a series of granodiorite dykes characterized by abundant hornblende, along with primary magnetite and subordinate sulphides scattered as roundish grains through anorthoclase and aligoclase feldspars and subordinate quartz. The rock is found as narrow dykes and shows no prominent secondary structures, either in the field or in thin sections under the microscope.

Jan 1, 1926

By Aaro E. Aho

Yukon, one of the most potentially accessible, relatively undeveloped, regions of Canada, has major mineral possibilities. The Klondike placer gold fields and the Mayo silver-lead ?district are the sole major producers but large base-metal re-serves have been discovered in re-cent years and important asbestos deposits are now being explored. Several major exploration companies are active in this region despite short seasons, permafrost overburden, remoteness, lack of transportation, and resultant high costs. Pro-posed new roads can be expected to accelerate development. At ?present the major future mineral possibilities are considered to be lead-zinc, copper, aslbestos, silver-lead, gold, and mineral fuels. These and other mineral possibilities are outlined for various geological subdivisions of Yukon. Major favourable metallogenic features of Yukon include complexity of rock types and structures, widening of the Cordillera with cross-trends, and variety and quantity of mineralization found even with limited prospecting. Comparisons with southern 'British Columbia and the U.S. Cordillera suggest that further exploration will result in discovery and development of more major ore deposits and reserves which will eventually revolutionize economy of mining in Yukon. Such mineral resources, with interior petroleum and natural gas possibilities, and ?huge coastal hydroelectric power potential, are the foundations of a much larger future mining industry in Yukon.

Jan 1, 1958

By L. Tafaghodi, A. Hosseinpour

"Silicon is considered as the most appropriate semiconductor material for manufacturing solar cells because of its natural abundance and being nontoxic. The transferable knowledge and technology from the electronics industry and the long history of silicon-based semiconductors are also assisting the domination of silicon as the most common semiconductor material. Developing an environmentally and economically viable process for producing solar grade silicon has been one of the main challenges in the silicon industry in the past few years. Metallurgical refining processes have received significant attention because of their high productivity and low cost. Slag refining is one of the purification methods which is based on oxidation of the impurity elements, followed by its dissolution into a slag phase. This article presents a review of various slag refining processes that have been employed for purification of silicon and silicon alloys. SiO2, CaO, CaF2, CaCl2, Al2O3, MgO and Na2O are the major components of the slags used for silicon refining. These slags can be classified into three main categories including binary, ternary and quaternary slags.INTRODUCTION Silicon can be categorized into three different grades based on its application or purity: metallurgical grade silicon (MG-Si) with purity of ~98 %, solar grade silicon (SoG-Si) with purity of ~99.99999 % and semiconductor grade silicon (SeG-Si) which has the purity of 99.9999999 % (Johnston & Barati, 2010; Krystad, Tang, & Tranell, 2012; Tang, Øvrelid, Tranell, & Tangstad, 2009). Producing SeG-Si is carried out through an energy-intensive and complicated process named Siemens. This purification process is relatively slow and involves using toxic and corrosive reagents (e.g. Trichlorosilane). At present the majority of SoG-Si is produced via Siemens or Siemens-like processes and there is very limited production via processes dedicated to SoG-Si. Because of the difference in silicon specifications required in microelectronics and photovoltaic industry, and the cost and energy associated with the Siemens process, an interest has emerged to develop technologies dedicated to producing low cost SoG-Si (Istratov et al., 2003; Johnston, Khajavi, Li, Sokhanvaran, & Barati, 2012; Mitrašinovic, D'Souza, & Utigard, 2012; Wu et al., 2012)."

Jan 1, 2017

By F. H. Edmunds

Introduction This paper, it is hoped, will serve as an introduction to further work upon the origin of the soils and to a more complete interpretation of the geology of Saskatchewan from a study of the soils of the Province. The great difficulty that is encountered in mapping the structure of the prairie regions of the west must be evident to all who have made the attempt. The rarity of good exposures, due to the extensive coverings of glacial drift, is the greatest obstacle, making it difficult to determine the exact stratigraphical position of such exposures as may be found. In many cases palæontological evidence is lacking, or, if available, our present knowledge of the stratigraphy is insufficient to justify division of the formations into horizons; and until many of these formations have been subjected to petrographic investigation, little can be done in using lithological differences as an aid to the correlation of the usually sparse outcrops met with in the Province. Topography may be of the utmost value as an indication of geological structure when considered in conjunction with other evidence. It does not necessarily follow that, because an area in Saskatchewan has resemblances in surface configuration to an area of oil-producing land in Texas, there is sufficient justification for sinking money in wells without further investigation. Such - investigation should include the study of available soil maps.

Jan 1, 1929

By Orlando C. Gaspar

The presence of ?ne-grained mineral intergrowths, the complex distribution of deleterious minor elements, and the variable base-metal contents in some assemblages commonly pose technical problems for the processing of volcanogenic massive sul?de ores. The bene?ciation of most massive sul?de ores from the Iberian Pyrite Belt requires extremely ?ne grinding to liberation sizes of K80= 15 µm to 25 µm. For several deposits, mapping of the ore types and metal zoning pat-terns has shown that the different ore types are distributed as ore lenses within the massive sul?des. Mineralogical, textural, and metallogenetic studies have provided an understanding of the distribution of both the vertical and the horizontal metal zonation in the orebodies. Because the ef?ciency of ore processing is affected by ore textures, and because the same mineral commonly has different textures and varies in chemical composition, a relationship between textures of the feed and the middlings must be established for all ore types de?ned at the deposit scale. Quantitative mineralogical methods have been developed to provide, on a timely basis, the information needed to optimize the concentration processes for the massive sul?de ores at the Aljustrel and Neves-Corvo deposits, Iberian Pyrite Belt, Portugal.

Jan 1, 1997

By V. Thangadurai

The critical problems in commercialization of the present solid oxide fuel cells (SOFCs) and useful electrical and physical properties of IT-SOFCs electrolytes are discussed briefly. The conductivity behavior of the perovskite-type and perovskite-related structure metal oxides are summarized. Perovskite-type La0.9Sr0.10ao.8Mgo.203_8 (LSGM) exhibits high ionic conductivity of 0.1 S/cm at 800 °C. In order to improve the electrical conductivity of LSGM and the In analogue of LSGM, substitutions have been made at the A-and B-sites. Substitution of trivalent La3+ by isovalent Pr3+ in LSGM and La09Sro ilno.sMgo.202.85 (LSIM), yield new mixed conductors. Among the investigated compounds in the present study, La0APro.4Sro.21no sMgo.2028 exhibits the highest total electrical conductivity of 3.2 x 10-5 S/cm at 200 °C in air with the lowest activation energy of 0.44 eV (200-700 °C). LSIM and Pr-substituted LSGM and LSIM perovskites show p-type electronic conductivity in the oxygen partial pressure range 10-5 ? 0.21 atm at 750 °C. The perovskite-type solid solution SrSn1-xFex03 exhibits compositionally driven phase transitions. For example, compound of the composition x = 0 to 0.3 crystallizes in an orthorhombic GdFeO3-like perovskite structure, where as that of x = 0.4-0.9 crystallizes in simple cubic SrTiO3-like, and that of x = 1 in orthorhombic structure. The electrical conductivity of SrSn1_xFex03 increases with the increasing Fe content and reaches a value of about 10-1 S/cm at 25 °C in air for x = 1. Compounds with low Fe content exhibit both ionic and electronic conductivity, while the higher Fe content 0.5) perovskites are electronic conductors over a wide range of oxygen partial pressure of 10-22? 0.21 atm at 750 °C.

Jan 1, 2005

By Mark McComb, Geoffrey R. Lane

"Over the years many differing approaches have been developed to clearly understand the nature, mode of occurrence, associations and deportment of both free-milling and refractory gold in a wide variety of differing geologic environments and plant products. Many approaches can be taken to characterize the ore which may occur as complex fine grained gold, ultra-fine grained gold, coarse nuggetty gold, complex Asrich refractory gold and double-refractory gold. The approach taken in assessing small drill core composites from Novo Resources Beaton Creek Paleoplacer gold project located in the Pilbara region of Australia was complicated by the nature of the ore, the small amount of sample available from current exploration work, and the gold grade and the grain size distribution. In this case the scope of the study was limited by sample availability although significant amounts of valuable information was also gained. This gold characterization study included the following elements:??Size fraction assays??Ore microscopy??Preparation of heavy mineral concentrates from sized fractions (screening) of crushed or milled head using heavy liquids and Superpan table.??Systematic scans of the heavy mineral concentrate, middling, and tailing fractions using TIMA Automated Scanning Electron Microscopy integrated with an Energy Dispersive Spectrometry to provide semi-quantitative elemental analysis of the individual grains found in the sample.The unique methodology employed to detail the gold deportment was the combination of the Tescan Integrated Mineral Analyser (TIMA) and the Oxford INCA GSR software. This technique not only allowed us to document the deportment of gold but recognize other associated minerals, which included gersdorffite, chalcopyrite, uraninite, coffinite, brannerite and several Rare Earth-bearing minerals.INTRODUCTIONGold deportment studies are commonly carried out on preliminary gold exploration projects in order to determine the various limitations, which may effect processing of the potential ore. This is often because it may be expected that there may be a refractory component to the gold, which may limit physical separation techniques and suggest more costly hydrometallurgical techniques. Often when carrying out gold deportment studies the mineralogical methods may be limited to assuming that the gold will be fine and easily found using standard techniques of optical microscopy or Scanning Electron Microscopy. This may not always be the case as various geological environments may pose their own individual problems to determining the deportment of the gold grains."

Jan 1, 2015

By W. J. Tough

THIS paper offers examples of some of the typical calculations which occur in the ventilation of metal mines. The fi.rst section of the paper discusses the problems associated with natural-draft pressure; the second section presents the more common of the calculations concerned with the operation of mine fans; the third section illustrates the integration of the individual problems covered by the preceding sections into the larger problem of determining the operating characteristics of a fan for a particular mine duty. There is a very definite limit to the extent to which pure arithmetic can be successfully applied to the solution of min<; ventilation problems. As mines advance from the exploration, development, and initial production stage to the rime when underground workings become exceedingly complex, there is a considerable increase in the relative importance o theory and judgment in the solution of ventilation problems. These calculations illustrate the application of mathematics to ventilation, but they also in-elude examples of instances where arithmetic cannot be conveniently applied, and important estimates, based on judgment compounded of experience and a knowledge of the theoretical consideration involved, must be made. The inclusion of such estimates is intended as a guide and a warning to the reader; a guide in assisting him to recognize and estimate his own incalculables; and a warning that the solutions must not be blindly applied to his apparently similar problems. These sample calculations are intended to assist the reader in applying the theory contained in the standard texts on metal-mine ventilation. They have been selected from the ventilation experience of a British Columbia mine.

Jan 1, 1942

By T. Lux, M. Hanel, Degel, A. Filzwieser, R., H. Joubert

It is the increasing demand for an economic and cost saving operation mode that requires effective cooling in order to achieve low refractory wear and good furnace lifetime, which is making cooling technology an important aspect of furnace operation. In addition, the requirements for safety are getting more and more into focus. However, the use of water—today’s standard cooling medium—has major drawbacks as it can cause problems both during furnace start up and operation, namely hydration problems, corrosion, and explosion. Not to forget the severe risks for the operators as well as economical damage in case of a malfunctioning water cooling system. With this new and patented cooling technology ILTEC and the ionic liquid IL-B2001 as the cooling medium, it is possible to realise a water-free cooling solution and therefore the door is wide open to rethink existing and conventional cooling solutions. Furthermore, there is also the chance to recover heat from the process in a more efficient way. However, since the technology is novel and unique there are a lot of concerns and doubts regarding safety for plant operators and employees. The paper is intended to cover both: highlighting the enormous potential of the technology but also to eliminate concerns mainly caused by rumour and unawareness. INTRODUCTION All of us are aware of the risks when water is used as a coolant and placed in the vicinity of the liquid metal phase. Unsuitable design solutions or wrong operation modes of the furnaces or failures of refractories can cause a direct contact of water with liquid metal. The consequences can lead to equipment failures, vessel destruction but even worse to injuries and even fatalities. Over the past decades, countless incidences were reported. Fatal accidents caused by water coming into contact with liquid metal happen every year (Oterdoom, 2014; Filzwieser, Konetschnik, Filzwieser, Wallnerm & Preiss, 2014). With the novel ionic liquid cooling technology virtually all negative effects of a water cooled system regarding safety are eliminated and even additional benefits can be provided (Voermann, Ham, Merry, Veenstra, & Hutchinson, 1999;Verscheure, Kyllo, Filzwieser, Blanpain & Wollants 2006; Wallner, Filzwieser & Kleicker 2006). The fact that no explosion occurs when IL-B2001 gets in contact with molten metal results in a revolutionary solution for the metallurgical industry in terms of safety—new safety standards can be achieved.

Jan 1, 2019

By C. A. Clark

The Chagres Smelter is located 80 kilometres north of Santiago - Chile, in the middle of an agricultural valley which is also one of the poorest districts in the country. This condition sets the main focus for the smelter&apos;s Corporate Social Responsibility (CSR) programmes, which ultimately aim at building self sustainable social and economic capital in accordance with the local capacities. With the help of Anglo American&apos;s SEAT (Socio Economic Assessment Toolbox), a corporately developed instrument designed to help the operations understand the needs of the communities and the impacts of those operations, the Chagres Smelter implemented several programmes, such as the CETTA (Experimental and Applied Technology Transfer Centre) programme. This project started in 2003, and consists of creating a centre for the transfer of sustainable techniques and skills for the small agricultural and livestock producers that live in the rural areas near the Chagres Smelter. Its main impacts are: Improved production quality (goat cheese and bee honey) and access to relevant markets, improved training and self-sustainability levels of producers, enhanced socio-economic level of the District&apos;s inhabitants by improving their income earning opportunities and technical knowledge, creation and promotion of a local brand as a symbol of quality products from the valley and a positive environmental impact of good breeding and native flora protection practices in the area. Other relevant social programmes are the &apos;Environmental Strivers&apos;, which created a recycling centre in the community; and the &apos;Beautiful Valley" project, which provides management knowledge and skills to local youngsters and leaders who can contribute to finding solutions for local environmental needs.

Jan 1, 2007

By A. D. Yell

"Recovery of water is always a major factor in the Beneficiation process. As Preparation Plants become larger the recovery of water for reuse, is a critical cost consideration. Tema Isenmann Inc in conjunction with our sister Company Multotec Manufacturing, has over the years, developed numerous different Screen Panels, Sieve Bends and Static Screens for dewatering. This paper will focus on a new innovation, the TeePee™ Panel which has double the open area of conventional Screen Panels. This results in efficient dewatering (reduced filter cake moistures) which allows for the use of smaller Vibrating Screens or increased capacity on existing Vibrating Screens. A major factor in the efficiency of any Screen Panel, including TeePee™ Panels, is the performance of the Vibrating Screen. If the Vibrating Screen does not have the required gravitational force or screen area to drain it will not dewater efficiently. Therefore a holistic approach has to be taken where the Vibrating Screen needs to operate at an optimal level, in conjunction with the correct Screen Panels, to achieve efficient dewatering. Key performance areas for Vibrating Screens are therefore detailed in this paper with an emphasis on important dewatering criteria. Case studies of different dewatering applications are included, where the use of TeePee™ Panels, has shown a marked improvement over conventional flat Screen Panels in reduction of filter cake moisture content.INTRODUCTION Dewatering can be done in a number of different ways and is largely dependent on the ore type, the particle size distribution and to what extent one needs to dewater will determine the method used. There are a number of different dewatering methods that can be used for particles above 200 micron, including Screen Bowl Centrifuges, Filter Presses, Static Screens, Static Sieve Bends and Vibrating Screens. This paper will focus primarily on Vibrating Dewatering Screens showing improved drainage and a reduction in the filter cake moisture content. KEY PERFORMANCE CRITERIAL FOR VIBRATING DEWATERING SCREENS For clarification the critical key performance criteria for Vibrating Dewatering Screens are set out in this paper. Dewatering Screens Vibrating Dewatering Screens are normally linear motion, either horizontal or inclined at 5 to 7° upwards with a vertical or back sloped plate at 45° to the rest of the screen deck. The back plate will often have screen panels in them to increase the dewatering capability, as shown in Figure 2 below."

Jan 1, 2017

By Paul Staples, Chris Morley

"The development of the Cerro Verde, Amplats Mogalakwena and Boddington projects over the last few years has helped to establish the use of high pressure grinding rolls (HPGR) in comminution circuit designs in large-scale hard-rock applications. The increasing acceptance of this innovative and sometimes controversial technology has had the natural effect of prompting many other new projects to examine HPGR as an alternative to the established, usually SAG-based, comminution circuit design approach.At the current stage of development of the technology, HPGR-based circuit capital costs are generally higher than for the equivalent SAG-based circuit, so that HPGR must offer sufficient operating cost benefits to offset the additional capital costs over an acceptable pay-back period. It is usually necessary to undertake comprehensive project-specific trade-off studies to quantify this effect.This paper describes the processes involved in the execution of a typical SAG-HPGR trade-off study, from the preliminary assessment of ore characteristics and project criteria, through testwork, circuit modelling, equipment selection and cost estimates, to a project-economics comparative assessment of the options. The trade-off study determines both the technical feasibility of the respective technologies and their commercial viability in the given project setting.The paper concludes with a cautionary note to the effect that, while HPGR has many potential benefits, it is not a panacea, and that, for some ore types and project conditions, the more established conventional technologies are often more appropriate."

Jan 1, 2010

By Normand Bédard

This presentation highlights Cambior?s initial approach for recruiting and retaining its international employees, the importance of proper preparation and the support needed to ensure a competent and stable workforce. In general, most of the training and information available for human resources personnel prepares the specialist for handling various aspects of labour relations, recruitment and hiring, benefits administration, employee relocation, etc. This is usually done in a Canadian context. Only recently, has more specialized training been developed to prepare human resources practitioners for the complex issues related to expatriate employees and dealing with human resources issues in other countries.

May 1, 2003

By Catalin Florin Petre, Elahe Ghasemian Langeroudi, Abdelaaziz Azizi, Éric Proulx, Caroline Olsen, Paul Blatter, Faïçal Larachi, Claude Gagnon

"The recovery of gold from ores is often accompanied by the release of other species in the leach solution. This state of affairs leads to depleted free cyanide levels in the slurry. Therefore, separation and quantification of these cyanicides and free cyanide at different stages of the cyanidation process as well as in waste solutions is crucial to provide mitigation tools by preventing leaching of deleterious metals for environmental considerations.COREM and the research group of Prof. Larachi have been working together on the control of gold passivation and cyanicides during cyanidation for several years. Previously, a first capillary electrophoresis (CE) protocol for the speciation of sulfur and cyanicides (SCN-, Cu, Fe) during cyanidation of gold complex sulfide ores was developed and validated for assessing industrial process water.The separation of zinc cyanide complexes used to be confronted with a number of difficulties due to the weak and/or undetectable cyanocomplexes in formally available CE protocols. Moreover, according to our knowledge, no direct CE protocol exists to separate free cyanide. Therefore, a new study aimed at developing a second CE protocol for the detection and quantification of cyanide complexes of zinc and nickel as well as of free cyanide in the cyanidation process water.To achieve this goal, six common carrier electrolytes such as pyridine, trimellitic acid, 4-methylbenzylamine, sodium chromate, phthalic acid and tris base were studied, using an indirect UV detection method. The best results were obtained using sodium chromate for which all ions were successfully separated and quantified. In addition, the effect of electric field strength, injection volume, electro-osmotic flow (EOF) modifier and background electrolyte (BGE) concentration were examined, while peak height, peak area and noise were considered for optimization.As a result, the new protocol is expected to complete the initial CE protocol by detecting cyanide complexes of zinc and nickel as well as free cyanide. Moreover, analytical determination of free cyanide in the presence of weak cyanide complexes achieved by the new protocol was also compared to conventional titration using silver nitrate solution. This new CE protocol will contribute to applied research and help plants to better understand and eventually control the behaviour of cyanidation circuits."

Jan 1, 2011