Search Documents

By Turgut Yalcin

"In this study, potential benefits of focculant usage were explored in the processing of mill tailings by hydrocyclones. Tests conducted on copper-nickel mill tailings have demonstrated that, under suitable conditions, flocculation could significantly enhance solid-liquid separation in hydrocyclones. For example, at a feed pulp density of approximately 9%, focculant-assisted hydrocyclone produced an underflow with over 98% solids recovery, compared to a recovery of less than 53% with conventional hydrocyclone. However, feed pulp density was found to be a critical factor, and tailings with pulp densities of greater than about 15%required a two-stage hydrocyclone operation where the focculant-assisted hydrocyclone was employed at the second stage to process the overfow of a conventional hydrocyclone.The underflow and overflow products obtained from the focculant-assisted hydrocy-clone may be discharged into tailings dams in the same manner as those produced by gravity thickeners. The focculant-assisted hydrocy-clone would, however, provide a higher throughput."

Jan 1, 1996

By Mingxia Liu, Hao Li, Qi Liu

"Laboratory batch flotation tests were carried out on fine (-20 µm) hematite to investigate the non-polar oil’s influences when sodium oleate, octyl hydroxamic acid, or oleyl hydroxamic acid were used as a collector. Batch flotation tests were performed with artificial mixed minerals (hematite:quartz = 1:1) under natural pH condition and kerosene was utilized as the model oil. The experimental results showed that kerosene emulsion behaved differently when used in conjunction with the three collectors. Kerosene helped improve the flotation when sodium oleate or oleyl hydroxamic acid was used as a collector. Nevertheless, it reduced concentrate weight yield, grade and recovery to a noticeable extent when octyl hydroxamic acid was used as a collector, especially at low dosages. In addition, single hematite batch flotation kinetics tests coupled with water recovery measurement were carried out to study the role of kerosene at different collector dosages. It was observed that water drainage and the resulting froth destabilization by kerosene was dominant at low collector dosages, especially in the flotation using octyl hydroxamic acid. At higher collector dosages, the water drainage and froth destabilization effect by kerosene was possibly counter-balanced by the higher hematite hydrophobicity and bubble surface tension gradient, which led to more stable froth layer.INTRODUCTION The minerals industry is facing a steady decline in ore grade, compounded by increasing complexity of mineral dissemination. As a result, the ore has to be ground sufficiently fine to have a suitable degree of mineral liberation, which produces large percentages of fine and ultrafine particles outside of optimal size range for ore dressing. Due to the unique characteristics of fine particles, i.e., small mass, high specific surface area, and problems such as increased solubility of complex minerals (Finkelstein, 1997; Finkelstein & Allison, 1976; Fornasiero & Ralston, 2005), high reagent consumption, fast surface oxidation in the case of sulfides (Collins & Read, 1971; Klassen & Mokrousov, 1963), severe particle entrainment (Subrahmanyam & Forssberg, 1988; Warren, 1984), low flotation rates (Glembotsky, 1953; Philippoff, 1952; Ye & Miller, 1988), slime coating (T. K. Mitchell et al., 2005; Parsonage, 1984), etc., flotation performance of these finely ground ores is very poor in terms of low concentrate grade and recovery."

Jan 1, 2017

By Chris McBean

Due diligence mistakes ? lost opportunity ? High profile write-downs and cost overruns ? Result ? tight market for financing ? Implications for due diligence ? need to get it right ? maybe only one chance ? Where should focus be?

May 1, 2013

By J. D. Little

"THE SALMO PROPERTIES of Canadian Exploration, Limited comprise forty-one Crown-granted mineral claims situated on Iron mountain between Sheep creek (on the north) and Lost creek, some eight miles southward from Salmo, in the Nelson mining division (see Figure 1). On these claims there are at present four operating mines. These are, from north to south, the Dodger, Feeney, and Emerald, all tungsten mines, and the Jersey, a lead-zinc mine, about 7,000 feet south of the Dodger. About midway between the Dodger and the Jersey is a fifth mine, the Emerald lead-zinc mine, which was the first producer in the area but has been inactive since 1926. The locations of the mines are shown in Figure 2.Records of prospecting and claim staking on Iron mountain -which owes its name to the presence of large iron-stained outcrops -go back to 1895. The first recorded owner of the claims that form the old Emerald lead-zinc mine was John Waldbeser who, in 1908, did considerable work and produced 426 tons of lead ore valued, at the then price of lead, at $7,000. This ore was chiefly lead carbonate and was taken from the surface outcrops of two bands of ore that form the Emerald orebodies. In 1909, the Emerald was the largest lead producer in the Nelson mining district."

Jan 1, 1953

By G. Bonin, R. P. Preston

"This paper presents a series of case studies where spherical camera photographs were used to generate 3D shaft models using photogrammetric methods. The shaft models were, checked for accuracy by comparing them to overlapping laser scan data, provided survey data or idealized shaft models. Short lengths of model were found to more accurately reproduce the shaft surface, with a best observed accuracy of 8 mm. Longer models encountered errors with accumulated errors as exhibited by slight deviations from vertical or slightly conical model shape. At present, the models are considered acceptable for general documentation and gross change detection. INTRODUCTION Shaft inspections are required by mining regulations in many jurisdictions and are commonly completed by trained mine personnel via visual inspections. This can be time consuming and prone to errors due to lapses in attention and the rapid travel rate required to inspect an entire shaft in a reasonable amount of time. Similarly, because of the time requirements, there can be impacts on other aspects of mining as a result of occupying the shaft for inspections. Spherical cameras with supplemental light systems offer a modern addition or alternative to conventional inspections. These cameras can be lowered relatively quickly to collect high definition, fully illuminated videos of the shaft that can be reviewed in detail later while the shaft returns to service (Gillis et.al., 2019). The use of cameras offers a further opportunity for valuable survey data generation from the same original data stream. The video data can be processed into three-dimensional (3D) models using Structure-from-Motion (Westoby et al., 2012) based photogrammetric methods. Depending on the quality of the source video and availability of survey control (required for all photogrammetry models) these models can be very accurate. Shaft surveying can be conducted with traditional theodolite methods but such surveys are time consuming and limited in their data density. Similarly, scans can be completed using conventional terrestrial laser scanners, but this requires a significant number of distinct setups to provide sufficient overlap between scans. Work is being conducted both on the laser scanning (SLAM, Durrant-Whyte & Bailey, 2006) and photogrammetry fronts towards kinetic scanning (Benecke, 2017) systems. The major advancement which is permitting these kinetic systems is Inertial Measurement Units (IMUs) which can provide localization in GPS denied environments and reduce errors associated with the open traverse format associated with shaft scanning."

Jan 1, 2019

By Jasmin Raymond

Ground source heat pumps are used to heat or cool building and heat water supply. Such heat pumps use the earth as a heat source or sink to efficiently provide or store thermal energy. For example, a ground source heat pump typically requires less then a third of the electric or fossil fuel energy of a conventional heater. Ground source heat pumps could therefore help reduce the energy consumption of active mines where low-grade geothermal resources are abundant. In most heat pumps, water or a water-antifreeze mixture having a temperature ranging from -6.5 to 43.5 °C is circulated through a heat exchanger at a rate of 0.000033 to 0.000067 m3/s (2 to 4 L/min) for each kilowatt of heating/cooling capacity. The groundwater that is continuously pumped to drain mines could be used to operate heat pumps. Water feeding a heat pump can alternatively circulate in a close loop network of pipes buried underground or installed in a surface water body. Retention water ponds, tailings and waste dumps commonly found at active mine sites could provide excellent environments to install the close loop system. Further research will help take advantage of the unexploited geothermal resources associated with actives mines.

May 1, 2007

By J. Donnelly, A. V. Deev

Substitution of coal and coke by renewable carbon (charcoal) is a low-risk and low-capital path to 50% or more reduction in net CO2 emissions by the steel industry. However, the high cost of charcoal and its low availability in most countries are barriers for the implementation of this approach. Development of an efficient wood carbonisation technology (slow pyrolysis) capable of producing large-volumes of charcoal from low-cost wood feed (e.g. wood wastes or forest residues) is an essential step towards the use of renewable carbon by the iron and steel industry. This paper provides a summary of the progress made over several years of R&D covering: (1) development and piloting of a new energy efficient slow pyrolysis process for production of charcoal from woody biomass at a competitive cost to the PCI coal, (2) techno-economic evaluation of the process. The main feature of the process is that the material undergoing pyrolysis is heated spontaneously without the supply of heat or air to the reactor. This makes it possible to carbonize large volumes of small-sized wood (e.g. wastes and residues) in a single reactor unit and capture high calorific value pyrolysis by-products

Jan 1, 2015

By D. Moronkeji, R. Maharidge, D. A. Curry, B. J. Davis, U. Prasad, J. Franquet

"Proper shale characterization is crucial in shale gas drilling, exploration, completion and production. Unlike porous sandstone and carbonate reservoirs, the challenge with shales comes from their micro- to nano-darcy permeability ranges and the anisotropy of their mechanical and hydraulic properties. Most porosity-dependent logs are not sensitive enough to capture the true behavior of shales. Consequently, mineralogy and other strength and stiffness-related properties must be determined to characterize magnitudes and variances in shale mechanical and flow properties. In addition, these properties must pass quality assurance/quality control (QA/QC) practices to give confidence in their use in subsequent log calibrations, during geomechanical modeling, or in fracture design models. This paper presents a technique to integrate shale properties that are measured by various methods, and a methodology to perform QA/QC on the data before application.Shale properties originate from various sources, including downhole and laboratory measurements. Physical samples for laboratory testing are usually limited to a few depths. Lab tests are often costly, and replicating in-situ conditions can be difficult or impossible. In addition, results frequently show wide scatter, reflecting inherent depth variability and lateral heterogeneity. Wireline logs provide nearcontinuous data, but rarely yield direct measurements of rock strength properties. Although geomechanical and fracture models use log data, calibrating it with reliable and previously verified lab-measured properties is important. This paper presents a process to perform QA/QC on lab-measured data using various crossplots.Ten mechanical, microstructural and physical properties are graphically displayed to visually characterize shale strength behavior in ambient and in-situ conditions, whether measured or modeled statically or dynamically. These properties are often sourced from different departments. The properties are integrated but are individually subject to the previously mentioned uncertainties. Pairs of property values are crossplotted and compared with correlations from the literature or previously established with qualified data from related formations. Conformance with these correlations gives confidence in the data, whereas outliers are flagged as questionable. Repeating the process with questionable data crossplotted against other parameters for the same depth highlights the property with the greatest uncertainty. The determination of its value is investigated to locate the source of the inconsistency and establish a more reliable value. Where this is not possible, the user has a rational basis for rejecting that property value."

Jan 1, 2015

By R. Cotton

"1. INTRODUCTIONTo say that the environment will be a dominant issue in the 1990' s is an understatement. A world-wide ""green revolution"" is taking place not only with the general public and politicians, but in the boardrooms and plant facilities of corporations around the world. There is probably not a plant manager who has not been requested by his corporation to assist in some way on environmental issues by providing advice and strategy, by dealing with customer or community concerns, by considering environmental matters in transactions, by developing new environmental compliance policies and requirements, and so on.There are, in the author's view, three main challenges for the mining industry in the environmental area in the 1990's. This paper will discuss each in turn. The first challenge is the concept of ""sustainable development"". Whatever the meaning of this much-debated phrase, we are rapidly moving beyond the buzzword, and into the specifics. It will clearly impact on the way we manage our companies, our communities and our personal lives.The second is the challenge of personal liability; particularly for officers, directors, supervisors and managers of the corporation. For example, in Ontario today, a good percentage of prosecutions for pollution offences are against individuals, usually managers and supervisors, in addition to the prosecutions against the corporation itself for the same offence. In all likelihood, prosecutions will increase in number and will increasingly be directed at individuals. A corporate president has already served a jail term for contempt of court related to his corporation's breach of a court order related to sewer by-law offences. Although the case is on appeal, another president has become the first officer in Canada to be sentenced to jail for violation of an environmental protection statute. Other corporate officers and directors have recently been charged with breach of their duty under Ontario's Environmental Protection Act."

Jan 1, 1991

By Leon J. Perrier

The paper describes the equipment in use, haulage grades, road conditions, tire sizes, tire performance and related problems. Various types of failures and causes, corrective action taken, tire records and reporting for control are also discussed.

Jan 1, 1977

By Malcolm Powell

"The argument has long raged across the oceans as to what the best AG/SAG mill aspect ratio is. The North American practice of a high aspect ratio of two, diameter twice length, through to the South African and Scandinavian practice of an aspect ratio of as low as a 0.5. Within the collaborative P9 AMIRA project the MPRU of the University of Cape Town and the JKMRC of the University of Queensland have been collecting plant data pertinent to this issue over the past four years.The JK SAG mill model developed by the JKMRC is based upon data collected from mills having a range of aspect ratios from 1 up to 2. The maximum mill speed, mill load, and ball filling in the fitted data base were all below the operating range common in South Afr-ica. The extension of the P9 project into South Africa therefore lent an ideal opportunity to collect data in a whole new window of operation that would allow the range of applicability of the semi-empirical SAG model to be greatly extended.At the heart of the differences in aspect ratio is the completely different operating practice for high- and low- aspect mills. The mill filling, mill speed, and recirculating loads of closed-circuit single-stage operation have more influence on the differences in operation than the pure aspect ratio relationship. Relationships for load have been extended to 45% filling, with the modified model showing the measured peak in throughput as the mill filling increases. The ball load relationship now covers fillings of over 30% balls (of total mill volume), thus including so-called SAG-ball mills. The influence of closed circuit operation has been measured. It has been found that a key issue of the high slurry flows associated with closed circuit operation, especially when closed with a cyclone, is the pulp discharge limitation of the traditional grate and radial lifter configuration. It has also been observed that absolute mill length is more of an issue than aspect ratio. Slurry flow along the mill and charge segregation within the load are being investigated on pilot and full-scale mills to provide data for potentially modifylng the perfect mixing model that is used for the SAG mill.Improved understanding of these aspects of SAG mill operation and extension of the JK SAG model to better cover the entire range is allowing serious direct comparison of high- and low aspect mills for the first time. It is the conclusion of the researchers working in this area that there is no one best practice, that in fact mills across the range have their application based on ore type, desired product, available capital and on operating costs. Developing robust designs allows direct comparison of two-stage circuits using high-aspect primary SAG mills, with single-stage closed circuit low-aspect SAG mills. The new operations within South Africa are now considering both circuit types, and data is presented on selections that cover the full range of aspect ratio and operating practice."

Jan 1, 2002

By Alexander Burns, David Dreisinger

The kinetics of the oxidation of uranium(IV) by oxygen gas in aqueous systems is dependent on acid concentration, oxygen partial pressure, and temperature. In order to better understand the relationship between these variables and the speed of oxidation, a series of experiments have been conducted where each parameter has been varied in turn. Data were collected continuously using UVVis spectroscopy, allowing for a detailed examination of the reaction rate over the course of each experiment. The data fit an overall apparent rate law that is 1.5order in uranium(IV), -2order in H+, first order in oxygen, and unaffected by uranium(VI). This relationship does not appear to hold for solutions with <0.2 mol/L initial acid, where a different kinetic mechanism appears to be dominant.

Jan 1, 2014

By C. Gosselin, G. M. Payenzo, C. Bazin, M. Desnoyers, G. Chevalier

"ArcelorMittal Mines Canada operates hydraulic classifiers to reduce the silica content of an iron oxide concentrate from 4.5% to less than 1.2% SiO2. Sampling campaigns were conducted to develop a preliminary model for the hydraulic classifier. Results show that iron oxide and quartz are respectively concentrated in the coarse and fine size fractions of the classifier feed. The mineral partition curves in the classifier and the size distribution of the minerals in the feed are used to simulate the classifier operation in order to identify the source of variability observed in the daily plant production data. Results indicate that most of the variation is probably caused by unsteady operating conditions of the classifiers.INTRODUCTION Hydraulic classifiers are a class of gravity separation devices (Wills, 1992) used to classify particles according to their size and specific gravity. Hydraulic classifiers also known as density separators (Hearn, 2002) combine hindered settling and upward flow of water to selectively entrain light particles to an overflow stream. Denser particles settle to an underflow stream. Hydraulic classifiers are used for various purposes ranging from cleaning of coal (Das, Sarkar, & Mehrotra, 2009), recovery of chromite from plant tailings (Kumar, Tripathy, & Rao, 2009) to upgrading iron oxide concentrate (Hearn, 2002). ArcelorMittal Mines Canada operates several hydraulic classifiers to upgrade an iron oxide concentrate by removing fine quartz and other light minerals from hematite that is the main iron oxide mineral. A project was initiated to analyze the operation of the classifier in an attempt to identify the source of the variability in the production results and to assess the potential of increasing iron recovery in the classifier. One possible disturbance for the classifier operation is the change in the classifier feed composition and size distribution, while the other considered disturbance is the operation of the classifier. The paper is divided into five sections. The first section summarizes the ore processing sequence for the production of iron oxide pellets to identify the position of the hydraulic classifier in the process. The second section describes the hydraulic classifier. The third section discusses the sampling campaigns conducted on the hydraulic classifier. The method used to process the data from sampling, the results of the data processing and simulation of the classifier are discussed in the remaining sections."

Jan 1, 2012

By G. J. Biefer

"Fatigue and corrosion fatigue measurements were carried out on five commercially available metals -four steels and an aluminum alloy -which are used as structural materials in mine shaft conveyances. In the corrosion fatigue measurements, drain waters collected in the shafts of three different Canadian mines were used as corrodents. The mine waters had been selected on the basis of their relatively large differences in acidity and/ or composition.It was found that the corrosion fatigue strengths of the four steels were similar, despite their differences in tensile properties, and that the type of water used in the tests had little effect on the results. Mild steel showed the highest and most consistent values of the damage ratio (ratio between the corrosion fatigue and the plain fatigue strengths at 107 cycles). The corrosion fatigue behaviour of the aluminum alloy (ASTM Type 6061-T6) was found to differ markedly in the three mine waters. A high damage ratio (i.e., superior performance) was shown in a mine water in which the corrosion attack was uniform; much lower damage ratios were shown in waters which produced localized corrosion attack. Corrosion rates were too low to be deter-mined conveniently by conventional weight-loss methods, but calculations from polarization curves provided a rapid demonstration that corrosion rates were distinctly lower in the mine water which produced high damage ratios."

Jan 1, 1967

By A. E. Cameron

The curve of coal production in Nova Scotia over the past forty years shows a definite maximum reached in 1913. Continued production to this maximum will require a greater tonnage per man-day, and this means there cannot be any increase in total man power used in the operations. There are still large reserves of coal but much of it will require washing or beneficiating to make a usable product. By-product recovery based on the present product ion is relatively satisfactory. Further development of secondary industries requires adequate markets for the bulk materials produced by the processing. It also requires access to other raw materials as well as markets for the principal product of the operations. Scientific investigation and research are needed to prove the quantity and value of lower grade or poorer quality coals, and methods for their recovery and utilization. Economics of further processing of present and future production must be investigated beforehand, if a successful development is to be assured. Such development cannot be expected largely to replace present markets. Production of coal for genera l use must continue to form the major function of the coal industry of the Province. Costs per ton must decrease, or subsidies or other assistance must increase, if the industry is to survive. Costs of investigation and research and costs of capital outlay for further development muse be met.

Jan 1, 1944

By C. D. Kaeding

IN the summer of 1937, the Algoma Steel Corporation, Limited, decided to embark on the full-scale development o their Helen mine and the erection of plants to produce commercial iron sinter from its ores at a rate ? of fifteen hundred tons per day. The Helen deposit has long been known as one of the largest bodies of non-commercial iron ore in Canada, consisting almost entirely of siderite with a band of pyrite along the north wall and some lenticular inclusions of pyrite throughout the mass. It originally contained a nominal amount of hematite (2,800,000 tons), localized at the western end of the ore-body, but this was mined out during the years 1900 to 1918. For details of the:-geology of the Helen range and of the surrounding district, the reader is referred to Memoir 147, Michipicoten Iron Ranges, Geological Survey of Canada, 1926 (1). The siderite mass was explored by diamond drilling in 1917 and the portion so drilled was estimated to contain 67 million tons of siderite averaging 36.0 per cent Fe, 3.2 per cent S, and 8.2 per cent SiO,, without establishing its ultimate depth or extent. The variation in the sulphur content shown by drilling was from 1.5 per cent in 72 per cent of the tonnage, to 7.2 percent in the remaining 28 percent. The pyritic ore aver-aged about 38 percent iron, but otherwise its composition was substantially the same as that of the siderite mass.

Jan 1, 1940

By Earl M. Frizzell, Joseph A. Dos Santos

"Conventional belt conveyors offer an economical method for transporting materials at inclines approaching 18 degrees. Sandwich belt conveyors may be used to transport materials at high angles, to 90 degrees, while maintaining the most positive features of conventional conveyors, that is, (1) proven conventional conveyor components. (2) high-speed operation, (3) high-single lifts, (4) continuous cleaning of the smooth surf aced belts, and (5) easy, quick repair by hot or cold vulcanizing. The present discussion deals with the evolution and development of sandwich belt conveyors to satisfy the operational requirements of the open-pit mining and materials-handling industries.A look at the limitation s of conventional shallow angle conveyors reveals the conveying angle at which a cover belt is needed. The relationship between conveying angle and hugging pressure by the cover belt is developed mathematically. A study of past and current developments reveals that the Loop Belt and Beltavator are significant advances in the state-of -the- art. The vertical radius of curvature constraints are discussed in detail and the constraint equations are developed. Criteria for future development is established as a basis for evolutionary developments in sandwich belt high-angle conveyors. The use of intermediate drives in sandwich belt high-angle conveyors is investigated.IntroductionIn connection with U.S. Bureau of Mines funded–study relating to continuous haulage from deep open-pit mines, the authors had occasion to study extensively, the use of high-angle conveyors as a means of hauling mine products continuously from the pit while maintaining optimum mine slopes to minimize total excavation. The many possible high-angle conveying methods investigated included skip hoists, bucket ladders, pocket belts, fin belts, cleated belts, sandwich belts, pipe belts, screw conveyors, slurry pipe lines, and others. The sandwich belt high-angle conveyor appeared to be the most operationally-appropriate and economical solution for the mining industry. The present paper presents the theory, historical development, state-of-the-art, and evolutionary developments in sandwich belt high-angle conveyors."

Jan 1, 1983

By F. R. Joubin

MR. CHAIRMAN, Members of the C.I.M., and Friends -particularly friends, because I am not entirely a stranger in your city. I was last here some five years ago and it has given me a great deal of pleasure this evening to be able to say "Hello" again to those I had met at that time, when Bourlamaque and V al d&apos;Or were very busy centres of intensive and successful gold exploration. My remarks this evening have to .do with Canada&apos;s Place in the Atomic Age. They will be of a general nature but I hope to tell you ?enough to whet your appetite so that you may be provoked into per-.suing the subject further. Now, atomic developments have become quite commonplace. Words like radioactivity, reactors, nuclear fission, and so on are known to everyone, even the youngsters. I re-member two or three years ago one of my office boys came to me and said "Mr. Joubin, I would like a raise." I gave the request a few seconds of serious thought and finally said "Alright, Jimmy, we&apos;ll give you a raise." However, he made no effort to leave, so after a -couple of seconds more I said, "Is there something else ?" and he said "Yes, Mr. Joubin, could you make that raise &apos;radioactive&apos; to the first .of the year ?"

Jan 1, 1958

By R. W. Allgood

"THE world-wide shortage of elemental sulphur, which became sharply apparent in 1950, has focused attention on the commercial exploitation of sulphur-bearing materials such as pyritic ores, sour natural gas, and smelter gases. Although there •are no known commercial deposits of elemental sulphur in Canada, there are vast quantities of these sulphur-bearing materials. The International Nickel Company of Canada and Canadian Industries Limited have for many years collaborated in an effort to develop economic processes for the recovery of sulphur from the smelter gas arising from Inco's metallurgical operation at Copper Cliff, Ontario. While sulphuric acid has been •produced at Copper Cliff for over twenty years, recent developments will result in a 60 per cent increase in acid production early in 1952 and, later in the year, in commencement of the operation of the largest single unit ever erected for the manufacture of liquid sulphur dioxide.The purpose of this paper is to discuss •briefly the general factors associated with the recovery of sulphur from the Copper Cliff smelter gases and to describe the sulphuric acid operations and the liquid sulphur dioxide development.Processes for the manufacture of elemental sulphur, liquid sulphur dioxide, and sulphuric acid from sulphur-dioxide-bearing smelter gases are well known and in some cases •highly developed."

Jan 1, 1952

By H. R. Shakeri, R. Mayer, M. J. Worswick, A. Rahem

The current focus of research and development in transportation industry is to use lightweight materials such as aluminium alloys for more structural components. In this regard, maintaining safety of the passenger and vehicle is the most important; therefore crashworthiness of components made of lightweight materials must be evaluated prior to sizable application of these materials. The focus of the present study is to understand failure and damage mechanisms during the axial crushing of aluminium tubes made of A1Mg3.5Mn alloy of 2 and 3.5 mm thickness. Due mainly to complexity of the crushed tubes, a microstructural approach is considered. In this study optical, stereo as well as scanning electron microscopy techniques have been used to study damage and failure mechanisms in these types of tubes, which are essential energy absorbing components in passenger vehicles.

Jan 1, 2006