Search Documents

The effect of superficial gas rate distribution (Jg profile) on down-the-bank metallurgical response was tested in the rougher-scavenger bank (eight 10-m3 tank cells, 4 roughers and 4 scavengers) at Highland Valley Copper Mine's Cu/Mo separation circuit. Three Jg profiles were tested: (a) as found (i.e., typical practice), (b) increasing decreasing (i.e., increasing from cell 1 to 4 and decreasing from cell 5 to 8), and (c) decreasing-increasing (i.e., decreasing from cell 1 to 4 and increasing from cell 5 to 8). The Jg profile approach proved to be of considerable value. Profile (b) gave the best metallurgical results, i.e., the highest down-the-bank grade/recovery (increase in grade at constant recovery was approx. 3-4% compared to the as found case) and the most efficient Cu/Mo separation (cumulative Cu recovery was reduced by almost half - approx. from 20% to 12%, at 99% Mo recovery). The success of the evaluation prompted the implementation of profile (b). Detailed gas dispersion characterization tests (Jg and Db (bubble size)) showed significant discrepancies between the Jg measured directly (using the McGill University sensor) and the Jg calculated from field instrument readings (volumetric gas flowmeter) and machine dimensions (cell cross-sectional area). Tests were designed to reveal the source of disagreement. It was observed that a significant number of bubbles were not able to float (i.e., they were entrained with the tailings), the evidence appearing to be a significant number of very small bubbles (approx. 200-300 µm) which did not have sufficient buoyancy to rise. Consequently, rather than relying on the field instrument, the evaluation depended on the McGill University Jg sensor, which collects bubbles in a tube near the pulp-froth interface, thus providing significance to the data as the measurements were obtained from bubbles that almost certainly floated.

Jan 1, 2007

By Rees J. Llewellyn

Improved product development, assessment methods and evaluation studies of materials for oil sands applications have traditionally focused on low and high stress abrasion and slurry erosion resistance mechanisms, because they were considered to be the predominant wear modes prevailing in oil sands mining, transportation and bitumen recovery. More recently with the very successful introduction of oil sands hydraulic transportation systems, there has been increasing use of crusher systems in which materials of construction are also required to have good toughness and gouging abrasion properties to withstand impact and the severe indentation and ploughing forces that are involved. To assess material property requirements for mitigating this additional wear mechanism, jaw crusher gouging abrasion tests using a modified ASTM G81 procedure, have been carried out on a range of wear materials of interest for oil sands mining service. The method involves a comparison of the wear losses that occur for reference and selected test plates when a controlled amount of standard feed rock is comminuted in a laboratory jaw crusher. Among the classes of material evaluated have been Q&T plate steels, austenitic manganese steel, chromium and chromium molybdenum white irons as plain castings and in laminated forms and also chromium carbide and tungsten carbide overlaid wear plates.

May 1, 2004

By Pierre Sauvé, Guy Perrault, Armand Savoie, Pierre Trudel

"La Mine Doyon est une entreprise détenue à parts égales par Cambior Inc. et par Minerais Lac Ltée qui en est l'opérateur. Les statistiques de production au 1"" janvier 1990 indiquent que, depuis le début de son exploitation (1980), 10.3 Mt de minerai d'une teneur moyenne de 5,9 g Au/t ont été usinées. Les réserves sont estimées a 10,4 Mt à une teneur moyenne de 6,6 g Au/t jusqu' à une profondeur de-450m.Trois zones minéralisées sont présentement en exploitation. Ces zones sont caractérisées par la présence de veines de quartz-pyrite accompagnées localement de chalcopyrite. Les roches encaissantes sont les schistes a séricite (zone# 1), les roches volcaniclastiques de composition felsique (zone #2) et intermédiaire (zone #2, zone ouest) ainsi que les roches intrusives appartenant au pluton de Mooshla (zone ouest). Toutes ces roches ont subi un métamorphisme régional dont l'intensité correspond à la limite supérieure du facies schiste vert ( -425°C}.Les zones minéralisées sont situées à I' intérieur des zones de déformation et d'altération les plus intenses. L'étude des structures mineures nous indique que la région a subi plusieurs épisodes de déformation ductile a fragile qui sont antérieurs, contemporains et postérieurs al a minéralisation. L'analyse structurale indique également que la déformation majeure est associée à une importante phase de compression orientée N-S a NNE-SSW.L’ensemble des observations suggère que la minéralisation et I' altération associée sont de type épigénétique. La mise en place du minerai se serait effectuée à la fin de l'épisode principal de métamorphisme et de la déformation."

Jan 1, 1990

By James D. Bittner

Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. The environmentally friendly process can eliminate wet processing and required drying of the final material. The process requires little if any pre-treatment of the material other than grinding and operates at high capacity ? up to 40 tonnes per hour by a compact machine. Energy consumption is low, approximately 1 kWh/tonne of material processed. Since the only potential emission of the process is dust, permitting is typically relatively easy. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (300 µm) materials with very high throughputs. The triboelectric particle charging is effective for a wide range of materials and only requires particle ? particle contact. The small gap, high electric field, counter current flow, vigorous particle-particle agitation and self-cleaning action of the belt on the electrodes are the critical features of the ST separator. The high efficiency multi-stage separation through charging / recharging and internal recycle results in far superior separations and is effective on fine materials that cannot be separated at all by the conventional electrostatic techniques. Since 1995, this triboelectric process has been extensively used for the beneficiation of coal fly ash with eighteen separators in place and over 130 machine-years of operation at locations in North America and Europe. ST has also installed separators for the beneficiation of industrial minerals in North America and Europe. The technology has been successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, barite, and potash.

Aug 1, 2013

By G. M. Mason

History Due to its strong affinity for oxygen, aluminium as an element was isolated only after many other rarer metals had been prepared and studied. It was just over one hundred years ago that two scientists, Hans Christian Oersted and Friedrich Wohler, produced the first few pellets of aluminium and determined its physical properties. These early investigators used metallic potassium as a reducing agent. Later, St. Claire Deville, by using sodium instead of potassium, improved the yield in the reduction and produced some pounds of aluminium. From a figure of about $110 per pound in 1855, the price had fallen to about $4 per pound by 1886. In that year, a very important discovery was made independently by Charles Martin Hall in Oberlin , Ohio, and Paul . Heroult in France. Stated in its simplest terms, the discovery of Hall and Heroult was that aluminium could be produced by electrolyzing a solution of the oxide in molten cryolite. The application of the Hall-Heroult process made the metal immediately available in commercial quantities and, by 1900, the price had fallen to 23 cents per pound. The growth of the industry in the past fifty years is well known, and is outside the scope of this paper. It is, perhaps, not generally known that aluminium was first produced in Canada at Shawinigan Falls in 1901. Since that time, production has been continuous at one or more smelters in the Province of Quebec. The largest of these smelters, which is also the largest aluminium smelter in the world, is at Arvida, Quebec, on the Saguenay river. A large power potential and access to ocean shipping were the two principal reasons for the establishment of aluminium production facilities in the Saguenay district. It is interesting to note that the aluminium industry, as a large user of power, took an active part in the early industrial development at Niagara Falls and Shawinigan Falls, and is now repeating the process in the Saguenay valley.

Jan 1, 1949

By Steve Wilson, Bern Klein, Jeff Drozdiak, Stefan Nadolski, Andrew Bamber

"In the adaptation of high pressure grinding rolls (HPGRs) to hard-rock mining applications, circuit development has mainly focused on placing HPGRs in the role of tertiary crusher in the preparation of ball mill feed. In order to take advantage of the potential energy benefits associated with HPGR and stirred mill grinding technologies, work was done to investigate the potential of and resultant energy benefits of placing the HPGR in series with a high speed stirred mill in replacement of the conventional cone crusher / ball mill arrangement. The proposed circuit was designed to operate with two stages of HPGR grinding followed by high speed stirred milling.Using a pilot-scale HPGR unit inline with a 20 liter stirred mill, the design criteria, circuit arrangement and consequent comminution energy requirements for a circuit processing copper sulphide ore from Teck Resources’s Mesaba Copper project were determined. These results were then compared to two other circuits, an HPGR / ball mill circuit and a conventional crusher / ball mill circuit processing the same ore.The testwork indicated at a proof-of-concept level that the HPGR / stirred mill circuit could potentially be appropriate for this duty and further work on the concept is merited. While the results indicate that the HPGR component of the circuit was more energy efficient than conventional cone crushing, the energy efficiency of the stirred mill was found to be lower than that of a comparable ball mill undertaking the same duty. However, increased energy efficiency of the stirred mill portion of the circuit is possible with further optimization and further work on the concept is indicated."

Jan 1, 2010

By A. G. Roach

IT IS generally stated that the gold ores of Nova Scotia are free-milling, and for the most part this is true. However, there is a certain proportion of the gold finely disseminated throughout the sulphides, notably arsenopyrite, and this gold is definitely not recoverable as &apos;free-milling&apos; gold by amalgamation. The proportion of free-milling gold to total gold seems to vary widely in different localities in the Province and is lowest in deposits of the fissure-vein type. The problem of recovery of these relatively recalcitrant values is usually one of economics, in some plac.es a simple gravity concentrate being of such low tenor that its extraction and subsequent disposal will not bear the costs involved. In other cases, such a high percentage of values escapes from the mortars and plates that concentration is definitely indicated. The size of the mining operation is also an important factor. In the large majority of cases, however, some concentrating step is warranted, even if the resulting concentrate is stock-piled until sufficient has accumulated to justify further treatment.

Jan 1, 1940

By S. Isaac

The networks of interdependencies between elements in building projects, referred to as the project topology, are often complex and difficult for project teams to comprehend. It is hypothesized that a graphbased model of the project topology can be based on existing data in Building Information Models (BIM), facilitating the application of graph-theoretic algorithms to analyze this topology. The objective of this study is to propose an outline for the synthesis of BIM and graph theory. This synthesis is expected to contribute to the development of new tools for representing, managing and analyzing the design of building projects.

Aug 1, 2013

By W. L. Nelson

The orebodies at Copper Mounta1n lie along and within a few hundred feet of the contact of an intrusive stock of gabbro with a series of bedded volcanic rocks of the Nicola formation. These. orebodies are all entirely within the volcanic series but in many cases the centre line of the orebody at depth is directly under the gabbro contact at the surface, due to a slight overhang of the gabbro. The gabbro and volcanic rocks are cut by a number of faults and fault zones which did not materially affect early mining operations, but, as undeground openings increased in size, the faults became more important factors in determining mining methods and procedure. Caving methods were adopted to take advantage of ground weakness in fault zones, and the effect of ground subsidence which resulted from the division of the ground 1nto large, independent blocks by faulting had to be considered in planning the sequence of mining of certain ore blocks. The faults have been divided into two classes: the longitudinal system and the cross faults, or &apos;breaks&apos; as they are termed locally. In addition to the two classes of faults, the zones of parallel ore fracture also control mining procedure, but to a lesser degree, in regard to caving or ground subsidence. A third structural feature which influences mining procedure is the mine dyke system. The longitudinal or main fault system roughly parallels the gab? bro contact and is made up of a number of branches and auxiliary fractures. The main fault itself is essentially vertical, but there are a number of branches and fractures on each side of it which, though parallel m strike, may dip as flat as 50 degrees toward or away from the main fault. The full width of the main fault system has not been determined, but it is known to extend beyond the zone of mine workings. A marked schistosity follows the main fault and both schistosity and chloritic alteration have been noticed along the secondary faults of this system. Several prominent orebodies lie along the main fault and its branches. The influence of the main fault system on mining is probably related more to subsidence than to actual cavi.ng, although it is effective in both.

Jan 1, 1950

By D. F. Coates

Slope problems arise on mining properties from cuts for roads and railroads and from open pits. When it is 'realized that 1,000,000 extra tons of waste may have to be mined as a result of an average slope being reduced by 1 ° it is easy to appreciate that the slope problems connected with open pits are of far greater importance than the others. The type of slope failure that can occur can be classified in different ways. The most useful classification would be one that separates the causes in such a way as to provide a basis for studies to deal with problems of prevention and control. Using this criterion the types of slope failures are classified into four groups. Having classified the problems in this way an understanding can be gained of the various mechanisms involved in failure ..

Jan 1, 1961

By A. H. Lang

THE recent production of important quantities of high-grade muscovite at the Purdy mine, near Eau Claire, Ontario, bas brought that district into prominence and bas added another strategic mineral to the list of Canadian products. The discoveries are thirteen miles west of Mattawa and about two miles north of the Trans-Canada highway and the Canadian Pacific railway. HISTORY Clear mica of low power factor is in considerable demand in Canada and in the United States for war purposes such as radio and telephone condensers, aircraft spark-plugs, radio tubes, and transformers. Some muscovite (white mica) bas been produced in North Carolina and New Hampshire, but the United States trade bas depended largely on importations of muscovite from India and of phlogopite (amber mica) from Madagascar. For many years Canada bas been a substantial producer of phlogopite, but was unable to compete extensively in the United States with importations from abroad. Canadian production of muscovite bas been negligible as no important deposits were known. Ever since the construction of the Canadian Pacific railway, attempts have been made from time to time to mine the pegmatite dykes in and near the Eau Claire area, but, although some feldspar has been mined, no appreciable muscovite was produced. Lace in 1941, J. Purdy and H. MacDonald discovered a dyke containing large crystals of high-grade muscovite from which they are reported to have sold $700 worth of mica. They recorded claims 35974 and 35975 in December, 1941, and claim 36095 in May, 1942.

Jan 1, 1943

By R. L. Christie

"THE ISLANDS lying north of the Canadian mainland, and the large Boothia and Melville peninsulas, form one of the great archipelagos of the world; this sparsely vegetated and nearly unpeopled region extends about 1,500 miles east to west and 1,200 miles from the mainland to the northern tip of the northern-most island. Sea access to most of the islands is restricted by ice to the summer season, and the 'polar pack' ice of the Arctic Ocean presses the year round against the northwest margin of the archipelago. Although the region is remote, the accessibility has greatly increased through a network of weather stations, airfields and air routes connecting with southern centres.The area considered in this paper is that part of the island region underlain mainly by sedimentary rocks. In broad terms, this includes the land and sea areas of the archipelago and the adjacent continental shelf, but excludes the dominantly 'Shield' terrain of Baffin Island, and of Melville and Boothia peninsulas. An impression of the size and potential of this sedimentary region may be gained by comparing some areas: the land area of islands underlain mainly by sedimentary rocks is over 300,000 square miles or about 50,000 square miles greater than the area of Alberta. The total area of the region, including the continental shelf and the inter-island areas, may be double this figure, and may approximate one-seventh of the land area of Canada."

Jan 1, 1970

By G. B. Harris, C. W. White

A study to investigate the recovery of base metals, notably copper, nickel, cobalt, zinc and manganese from iron-free concentrated chloride solutions using ion exchange was undertaken. In such solutions, apart from nickel and, to a lesser extent manganese, these metals are present predominantly as complex anions, and therefore conventional separation techniques based on cationic resins are not applicable. The results demonstrated that zinc, copper and cobalt can all be separately recovered leaving nickel and manganese behind. Specifically, zinc is a major nuisance element in nickel and cobalt processing, and the testwork showed that it can be preferentially removed prior to copper and cobalt. Selective resins for both copper and cobalt were identified, and it was demonstrated that the strength of the chloride background matrix has a significant effect on the efficiency of separation. An additional major advantage in such systems is that stripping can mostly be effected with water. Finally, some observations are made on the hurdles that must be overcome when attempting to introduce and commercialise new technologies.

Jan 1, 2015

"Drilling twinned holes is a traditional technique used for verification of intersections of high-grade mineralization, testing of historic data, or confirmation of drillhole data during geological due diligence studies. Twinned holes can also be used for special tasks such as correcting earlier data that are recognized to be biased. Successful implementation of the twinned-holes technique requires thorough planning. Experience suggests that good practice is to drill twinned holes no more than 5 m apart. Many unsuccessful twinned-holes programs could possibly have failed because the twinned holes have been drilled too far apart.Twinned holes are best compared by mineralization intersections and, if the data and geological characteristics of the deposit permit, by samples, equal-length composites, or geological units. Variables to be verified by twinned holes should include the thicknesses of the geological units of interest (e.g., mineralized thickness) as well as the presence of significant geological features (e.g., ore/mineralization contacts, alteration, etc.).A formal, rigorous analysis of twinned-hole data is essential. Repeatability of sampling, analytical results, and bias must be analyzed and statistically quantified. The number of twinned holes required for conclusive statistical and geostatistical analysis can be as high as 20-30, in particular where the studied variables are characterized by high short-range (local) variability.The efficiency of this approach is demonstrated by several examples of successfully applied twinned-hole projects, including applications to orogenic gold, mineral sands, bauxite, and iron ore deposits."

Jan 1, 2009

By F. Chachula, A. Molinaro

"Sulphide mineral flotation operations continuously strive for a balance between mineralogy, mineral liberation, circuit conditions and reagent solutions to maximize the production rate and recovery of payable metals. The Taseko Gibraltar copper – molybdenum mill operations underwent an extensive project focusing on the fundamentals to identify the effects of process conditions and mineral liberation to improve the bulk circuit copper – molybdenum recovery efficiencies in the bulk flotation circuits. This discussion will provide process data that demonstrates; 1) fundamental relationship between mineral liberation to recovery and grade, 2) flotation circuit condition testing and optimization, 3) reagent combinations resulting in efficient/economical mineral recovery, and 4) the development of a xanthate free reagent solution. The data presented and discussed will also touch on flotation parameters including pH, retention time, kinetics and the effect on bulk circuit recovery performance.INTRODUCTION Taseko's is the owner (75%) and operator of the Gibraltar copper-molybdenum mine, located in south-central British Columbia, the second largest open pit copper mine in Canada and the largest employer in the Cariboo region. Taseko restarted Gibraltar in 2004. From 2006 until 2012, the company invested ~$700 million to expand and modernize the operation which was originally scheduled for demolition when the company acquired it in 1999. In the spring of 2011, construction commenced for Gibraltar Development Plan 3 (GDP3). GDP3 included the construction of a standalone 30,000 ton per day concentrator, built adjacent to the existing 55,000 ton per day facility. The new design capacity of Gibraltar was designed to be 85,000 tons per day. An integral part of the project was a new molybdenum recovery facility. In addition to the new concentrator, the mining fleet was upgraded with a new mining shovel, production drill and ten haul trucks (Taseko, May 2015). In May of 2015, the Company completed an updated mine plan for Gibraltar featuring a 50% decrease in strip ratio. This new mine plan was a result of a detailed, six-month engineering study and forms the basis of an updated NI 43-101 compliant reserve (Taseko Announces Improved Economics At Its Gibraltar Copper Mine, 2015). The new mine plan took into account lower milling costs as a result of the modernized processing facilities (Taseko, May 2015)."

Jan 1, 2018

By E. S. Moore

In order that a logical conclusion may be reached regarding the possible occurrence of commercial iron deposits in Canada it is necessary to consider some important producers found elsewhere on this continent. A study of such deposits reveals the fact tl:~at a number of distinct types are producing large tonnages of ore. These types may be classified according to origin and occurrence as follows: (1) Bedded sedimentary deposits. (2) Contact metamorphic deposits. (3) Residual ores. (4) Lenses in metamorphic rocks and m some cases of uncertain origin. In addition to the types listed there are other deposits which have contained or do contain considerable ore and they either have not been worked on a large scale or they have been nearly exhausted. These include the following types: (1) Magmatic segregations. These are mostly titaniferous magnetites. (2) Dikes of magnetite of igneous origin. (3) Bog and lake ores in glacial drift. (4) Black sand placers.

Jan 1, 1925

By Z. Bibak, S. Banisi, A. Ghasemi, E. Nematollahi

"The major importance of liners in grinding is their role in providing an appropriate trajectory for the charge. Since it is not possible to study the charge movement by direct observation in operating industrial mills, this task is accomplished by physical (laboratory), and/or, mathematical (software) methods. Because of the high cost and a longer time required for a physical analysis, mathematical simulations have become more common. Simulation of the effect of liner shape on the charge movement has provided a means to select a proper design based on the operational objectives and conditions. Furthermore, the liner shape changes due to wear and impact during operation, which will influence the charge trajectory. This adds more of an incentive to use simulation. These changes in liner could be predicted through liner profile measurements during operation and/or simulation. In this research, an inhouse developed DEM software called KMPCDEM © was used to simulate the charge movement in industrial plant SAG mills. A geometrical method of implementing the shell liners on SAG mills at the Sarcheshmeh (9.75×4.87 m) and the Gole-E-Ghohar (9×2.05 m) operations facilitated the software simulation. Point by point implementation of the measurements of liner profiles of these mills enabled the study to trend the change in the charge movement as the liners wear. Comparison of the simulation to a laboratory mill (1 m diameter) showed that the difference between the measured and predicted charge impact point, shoulder angle and toe angle were 6, 4 and 3°, respectively. INTRODUCTIONComminution is the most energy intensive operation constituting the major portion of operating and capital costs of a mineral processing plant. In the last decade, a vast number of research was aimed at studying various aspects of grinding with the aim of performance improvements (Davis, 1919; Mishra & Rajamani, 1990; kalala, Breetzke, & Moys, 2008). Mill liners transfer the input power to the charge and play a significant role in affecting the motion of the charge (Mclvor, 1983; Mishra & Rajamani, 1990; Radziszewski, 1997; Van Nierop, Glover, Hinde, & Moys, 2001; kalala et al., 2008). Lifters are usually used with mill liners to extend their life and to enhance the grinding and impact breakage efficiency. Mill lifters are used to raise the grinding media and ore to transfer the energy from the mill to the load (Rezaeizadeh, Fooladi, Powell, & Weerasekara, 2010)."

Jan 1, 2016

"Previous studies on the effect of polytetrafluoroethylene addition during chalcopyrite leaching under conditions similar to those of the CESL process have reportedly resulted in complete leaching of the copper without the need for grinding of the flotation concentrate. However, these studies employed a pulp density of only 1% and finely sized PTFE particle that required the use of high impeller rotation rates that are not sustainable at an industrial scale. This paper explores the performance of 1/8” diameter balls of PTFE, that readily sink in the leach solution, on leaching performance at impeller rotation rates and ore pulp densities more typical of industrial practice. Possible routes for separation of the PTFE from the leach residues and their regeneration for recycling back to the leaching stage are also discussed.INTRODUCTIONChalcopyrite, CuFeS2, is the most important primary sulfide source of copper. While pyrometallurgical smelting of chalcopyrite remains the only widely accepted route for treating chalcopyrite concentrates, several medium temperature pressure oxidation processes are claimed to be economically feasible (Muir & McDonald, 2007). Among these, the CESL process has been extensively piloted and demonstrated at the prototype scale. The overall process chemistry of the CESL process may be summarized as follows (Marsden & Wilmot, 2007):4CuFeS2 + 5O2 + 4H2SO4 ? 4Cu2+ + 4SO4 2- + 2Fe2O3 + 8S0 + 4H2O (1)4CuFeS2 + 17O2 + 2H2SO4 ? 4Cu2+ + 10SO4 2- + 4Fe3+ + 2H2O (2)Though copper extractions of over 95 % are achieved, the CESL process requires extra grinding of the concentrate (Muir & McDonald, 2007). This is because leaching is conducted at temperatures around 150 °C, where the elemental sulfur produced is molten and grows thicker on the mineral’s surfaces as oxidation progresses, creating an increasingly large barrier for mass transport. In addition, the sulfur is sticky and tends to cause the mineral particles to agglomerate, effectively halting further oxidation of the particles that end up embedded within the agglomerates. Consumable surfactants, such as ligin sulfonate, have been shown to be effective at avoiding agglomeration, but they are not effective at removing sulfur from the minerals. Hence, their use does not obviate the need for fine grinding."

Jan 1, 2012

By L. O. Thomas

BROADLY, Yukon is divisible into three physiographic provinces which are extensions of the similar divisions in British Columbia that are there known as the Coastal system, the Interior system, and the Rocky Mountain system. South of Yukon to about the 50th parallel of latitude, the Coastal system consists solely of the Coast range, which, in Yukon, passes behind the St. Elias range and for the remainder of its course constitutes the most easterly portion of the Coastal system. The extension, in Yukon, of the Interior system of plateaus and mountains of British Columbia is commonly referred to as the Yukon plateau, and the extension of the Rocky Mountain system as the Mackenzie Mountains system. The Coast-Range province is largely made up of granitic intrusives; the Mackenzie Mountains province of folded sediments; and the intervening Yukon Plateau province of ancient metamorphic rocks, folded sedimentary rocks, volcanics, and intrusives. Almost the entire area dealt with in this article was subjected to glaciation and, in those parts where its full effect was experienced, the valleys were invaded by vast masses of ice which transported and scattered the stream gravels, with their gold content, so that, even where gold still remains in the old stream channels, it has become so buried under boulder clay and other glacial accumulations that it is, in most places, difficult to find, and, when found, may prove very expensive to mine. Most of the present rivers have done little more than cut new channels in the glacial debris, touching only here and there upon the subjacent rocky floor. The territory in Yukon adjacent to the section of the Alaska highway between Watson and Teslin lakes is for the most part unknown both topographically and geologically. From Teslin to Kluane, the highway travels a fairly well-mapped part of Yukon, but beyond that point, until White river is reached, the geology of the adjacent country has, largely, yet to be determined, particularly on the north side of the highway.

Jan 1, 1943

By G. Gauvin

Life span of aluminum smelting electrolysis cells can reach up to 3000 days. During this period, cathode blocks go under various physical and chemical changes that could result in an increase of electrical resistivity. The increase may be due to carbon migration from the cast iron to the steel bars, gap evolution between the cathode block and the cast iron, cathode cracking, etc. This paper focuses however only on the collector steel bar electrical resistivity evolution. To reveal the main phenomena responsible for the electrical resistivity increase, chemical analysis, metallographic and electrical resistivity tests were conducted on two steels bars picked from two Hall-Héroult cells after autopsies. Cathode voltage drop and temperature were measured using electrically insulated internal probes and thermocouples on 16 samples from each steel bar. Electrical resistivity can reach up to 1.21µO-m for a steel bar aged 2505 days compare to 0.142µO-m for steel AISI 1008 at room temperature.

Jan 1, 2011