Search Documents

By François Robichaud

"The Laronde mill has been in operation since 1988. Actual milling rate ranges from 7,000 to 8,500 mtpd. Laronde uses SAG/ball mill grinding followed by copper and zinc flotation circuits. A cyanidation/Merrill-Crowe process recovers the remaining gold and silver in the flotation tails.In 1999, the carbon in pulp circuit was replaced by a Merrill-Crowe circuit in order to cope with a much higher ratio of silver/gold associated with the discovery of the Penna shaft. Marine type diatomaceous earth was used as filter aid in both clarifier pressure leaf filters and recessed pressure filter presses from 1999 to 2005. In 2005, this filter aid was gradually replaced by alpha-cellulose after several laboratory and plant filtration trials. The selected cellulose is considered to be much less sensitive to parameters such as pH and reagent concentration and have increased clarifier and filter press filtration performance. Also, since cellulose is exothermic, replacing diatomaceous earth with cellulose as filter aid in the filter presses has increased calcining and oxidation rates in the calcining ovens since cellulose is exothermic. Finally, better calcining conditions have resulted in energy and reagent savings at the arc furnaces.This paper describes how the filter aid replacement has contributed to increasing productivity and Net Smelter Return of the refinery while reducing worker’s hazards and operating cost.INTRODUCTIONAll Merrill-Crowe circuits in the world are operated with filter aids. For years, the market for precoat filter aid has been dominated by mineral filter aids such as diatomite and perlite. Flowsheet and equipment selection at the Laronde refinery were performed in the late nineties. At that time, some key parameters of the design criteria had clearly identified marine type diatomaceous earth (DE) as the most successful filter aid. Parameters such as reagent cost and availability, clarity of the filtrate solution and good historical filtration performance in other concentrators had designated DE as the best suited filter aid. Pregnant solution processed in the refinery from its start-up through 2001 was fairly stable in flow rate and reasonable in terms of impurity content (cationic and anionic compounds)."

Jan 1, 2007

AT the Annual General Meeting held in Winnipeg last March, the whole of one of the technical sessions was devoted to a special Symposium on Geological Investigations in Canada, introduced by a paper entitled The Geological Survey (lî which had been specially prepared by Dr. G. A. Young, Chief Geologist of the Survey, and had been published in the February BULLETIN, prior to the meeting. Geologists from each of the provinces contributed to the Symposium, including directing officials of the geological divisions of provincial Departments of Mines, representative geologists from the Universities, and company and consulting geologists. Space, unfortunately, does not permit publication of a complete record of the proceedings,_ or even inclusion of all contributions to the discussion. The following summary, however, gives what is believed to be a fair cross-section of the opinions expressed by representatives from each Province. The Symposium resolved itself largely into a discussion as to how the Geological Survey and the several provincial bureaus or divisions of geology could co-operate most effectively in the important task of carrying out geo-logical investigations, with avoidance of duplication of work and waste of effort, and, so far as broad principles are concerned, there was remarkably close agreement among those participating in the Symposium as to how the various types of investigation should be allocated as between the Federal and Provincial organizations. Briefly, the concensus was that the Geological Survey can render the most effective assistance by conducting reconnaissance investigations, with mapping at 4 miles to one inch, leaving to the provincial organizations the more detailed, and hence more local, studies and mapping at larger scales. There was general agreement that the preparation of base maps, essential to systematic geological investigation, is a service devolving upon the Federal Government.

Jan 1, 1940

Block caving is an underground mining method for the profitable extraction of massive, low-grade orebodies. Lately, it has become the mining method of choice, for many mining companies, because of depleted high-grade orebodies, and declining metal market prices. Block cave mining, however, still faces several challenges. Lack of access to the cave remains a major issue in understanding the rockmass response to mining for method optimisation. Improving our understanding of the rockmass response to caving will lead to safer and more productive operations. Combining large datasets from multiple sources with virtual reality scientific visualisation (VRSV) is a viable alternative to understanding complex cave behaviour without access to the cave. This is achieved using immersive environments with the ability to view complex multi-dimensional data (beyond 3D) graphically. VRSV offers a unique platform where it becomes possible to immerse the multi-disciplinary experts, and/or management team, in a virtual mine environment for quick decision making and fast resolution to conflicting conclusions. The underground mining system is complex due to multiple interrelating factors such as geology, excavation geometries, stress and time. Block caving is even more complex than most underground mining methods due to the network of tunnels required, and the use of induced stress, among others. As a consequence of the complexity in the block caving environment, it is vital that the mining system is analysed holistically, as a system, rather than optimizing individual factors one at a time. This paper presents a customised software module developed for use in the Advanced Visualisation Interactive Environment (AVIE) at The University of New South Wales (UNSW), Australia, to enable VRSV investigation into block cave mining systems (BCMS). This approach has the potential to provide a better understanding of the effect of time in in rock engineering, which has proven to be an important factor in hard rock mines (Ma & Daemen, 2006; Malan et al., 1997; Suorineni, 2010) but never validated. This work back analyses the early undercutting phase of a case study block caving operation with the view to understanding time/sequence effects. There is evidence that heterogeneous rockmass time-dependent behaviour governs the seismic response of the rockmass following undercut developments.

Jan 1, 2015

By Hans Lundberg

The magnetometer which was developed during the war for detecting submarines has proven exceedingly valuable in outlining deep-seated structures in oil exploration, and will be useful also to geologists in outlining regional structural features in the Precambrian. Our magnetometer has been developed to outline local and detail structures. 1 am quite sure that all geophysicists and geologists would agree with me that, in ore prospecting, it is important to obtain as much detailed information as possible. We know that, as we ascend from the ground and get away from the magnetic ore-bearing structures and orebodies, the magnetic intensity decreases rapidly, but, worse than that, we lose the details even faster. Figure l shows two strong, very sharp, magnetic 'highs' over two orebodies which, as our distance increases, rapidly merge into one fairly broad, moderately strong anomaly. If we drilled on this maximum, we would not encounter any of the orebodies. Therefore, we should fly the airborne magnetometer as close to the ground as possible in order to duplicate the results of the magnetic ground surveys. The first chance to accomplish this came with the helicopter, which is an exceedingly maneuverable aircraft. It can be landed in a cleared space not much more than fifty feet square. With floats, it can be landed anywhere, even in a swamp, on thin ice, or on soft snow. It can stand still in the air, hovering over a given point. It can ascend and descend vertically, fly sideways and even backwards, at the will of the pilot. It flies forward at any speed up to l00 miles an hour. The helicopter can be taken to any desired position at a given time. It can fly at any useful altitude from a few feet to several thousand feet above the ground. It can fly very close to the ground with safety. In bare areas, the survey flight may be performed a few feet above the ground. In forested areas, however, the flights, to clear the trees, must be made at l00 to 150 feet. To mark out a certain point, a small parachute-like marker may be draped over a tree or laid on the ground. This can be done from the helicopter without touching the ground.

Jan 1, 1947

By M. Girard, C. Farsangi, N. Singh

"Canadian Royalties Inc. owns and exploits the Nunavik Nickel Project: a copper and nickel deposit in Nunavik, Québec. The nickel and copper concentrates are filtered by plate and frame filter presses, and are transported 100km north to Deception Bay by truck. As the site is situated in the far north, extreme weather can be detrimental to production: roads can close for significant periods of time, resulting in the concentrator using all its storage capacity. During the winter of 2017, this accounted for over 100 hours of unplanned mill downtime. Different solutions to this problem were evaluated and the most economically viable combination of solutions was determined to be the use of concentrate storage containers and upgrading the plate size of the existing nickel filter press. By satisfying new, increased utility requirements, the cycle times would not change, but produce 30% more filter cake. Simulations were developed to determine the number of concentrate containers needed in conjunction with the upgraded press to eliminate unplanned downtime due to road closures and secure production through the winter. This paper summarises these simulations, the commissioning and start-up of the upgraded filter press, container loading procedures, and how this was put together to achieve a record 2018 winter season with a 90 percent reduction in downtime. The payback period of the project was 4 months. A specialised side-tipping trailer emptied the containers during the fall of 2018.INTRODUCTION The Nunavik Nickel Project is a nickel/copper mining project located in Nunavik, Québec. The nickel and copper concentrates are stored in stock tanks after thickening and are then filtered by plate and frame filter presses at the concentrator before being transported 100km to the shipping port at Deception Bay by trucks. The region is prone to periods of extreme weather during the winter, with winds that can reach +100km/hr and blizzards that severely limit visibility. The roads to Deception Bay are often affected by this weather, causing closures that last an average of 18hrs and as long as 72hrs. Additionally, there is a 15% chance that road closures occur within 24hrs of the last event. This has been an issue for the concentrator team since start-up in 2013, causing unplanned mill downtime every winter (Table 1) due to filling concentrate storage capacity during prolonged closures of the roads to Deception Bay."

Jan 1, 2019

By H. Kuno, H. Kobayakawa

A borehole inclinometer with FBG optical fiber sensors has been developed to clarify very slow slope movements, and the results of its application to a real slope have been shown. The main characteristics kept in mind while developing this inclinometer are as follows. Firstly, the workability must be good so that only one cable is required for taking the measurements, because the inclinometer is composed of several FBG sensor elements constructed on an optical fiber. Secondly, the minimum interval of the distorted measurements must be close, namely, within 100 mm. Thirdly, the inclinometer must excel in thunder resistance. The measurements were executed by setting up the developed borehole inclinometer on a slope where the rate of displacement is several millimeters per year. The movement of the device was developed by comparing it with that of the results of an existing borehole inclinometer. The area of the displacement concentration, 1 m in width for 4-m sections, was confirmed by the existing borehole inclinometer. The boring core, recovered using a high-quality drilling technique, was examined. Landslide clay was not permitted at the location where the displacement had concentrated as a result of comparing the measurement results with the boring core, and the rotation of gravel by the movement of the slope’s land block was allowed. These results show the slope being caught in the stage just before a primary landslide. In addition, the feature whereby the slope behavior depends on the depth was analyzed by comparing the information on the underground displacement with precipitation and earthquake records.

Jan 1, 2015

By S. J. Laskowski

In potash ore flotation, carried out in NaCI-KCI saturated brine (about 6-7 molar KC1 and NaCI solution), long-chain primary amines are used as flotation collectors. Long-chain primary amines are poorly soluble in water and their solubility further decreases at high electrolyte concentration. For ionic surfactants there is a characteristic temperature (Krafft Point, KP) below which their solubility is too low for micellization. In a previous study, the effect of pH on the KP of dodecylammonium chloride in water was determined [Q. Dai and J.S. Laskowski, Langmuir, 7, 1361-1365 (1991)]. This paper deals with the effect of electrolyte concentration on the KP of dodecylammonium chloride. The derived theoretical relationship between the KP and the critical micelle concentration (CMC) for dodecylamine can be used to calculate the KP for electrolyte concentrations of up to 0.5 mol/L (about 8% NaCI-KCI brine). A simple experimental procedure for the determination of the KP for higher electrolyte concentrations is also described. The results show that the Krafft point of dodecylamine increases from about 17-18°C (in distilled water) to about 80°C at 16% brine saturation.

Jan 1, 2006

By S. J. Schofield

INTRODUCTION ONE of the greatest and most interesting problems of economic geology is to discover criteria bearing on the persistence of ore in depth. It is a question which is very much to the fore in connection with many of our important mines in British Columbia, and, as is to be expected, it is a most controversial one. The present paper, summarizing the views of the writers concerning the possibilities, in some of the mining districts of the Province, for the persistence of commercial ore to greater depths than have been, or are at present, mined, is offered as a basis for a general discussion on the subject and to call attention to the need for renewed study and research on the problem. Sooner or later-at some depth or other-individual ore-shoots become impoverished and bottom. In many mines where this has happened, either at the same or at a lower horizon, another ore-shoot, which had no surface outcrop, has been encountered and has continued downward until it, in turn, has pinched out. The Kolar (Mysore, India) gold field, for instance, presents interesting examples of this recurrence of ore-shoots at depth (1). For many years these mines have been under the management of Messrs. John Taylor and Sons. On more than one occasion they have persisted in sinking or drifting on barren quartz or along a narrow fracture for many hundreds of feet before values were again encountered. Their earliest experiment in such bold development took place at a depth comparable to that at which most mines in British Columbia are considered to be bottomed. In the past, is has been concluded that the ores in British Columbian mines do not go below approximately 2,000 feet, and to that depth only in a few instances. Consideration of the depth to which ores have been mined in the Province appears to support this view. The figures shown in the accompaning table have been gathered from various sources and are approximate.

Jan 1, 1935

By A. Lewis, J. Zachwieja, M. Widell, P. Zhou, W. W. Geissler, M. Svensson, A. Movahedi, H. Nordberg

Flotation collectors for sulfide minerals has been traditionally based on xanthate, thiophosphate, thiophosphinate and thiocarbamate, all derived from sulfur chemistry. Tecflote™ is a new family of patented collectors based on nitrile chemistry which can supplement or replace thiol collectors, depending on the ore types. A steep grade-recovery curve typical of Tecflote™ collectors was observed when using Tecflote™ as the main collector for the rougher and cleaner steps allowing a better recovery compared to current thiol collectors while maintaining the desired grade. Additional recovery increase has also been observed by the addition of scavenger steps using Tecflote™ collector in combination with current thiol-based collector. The selectivity seen in the lab is transferred to full scale trial and is clearly seen in the rough flotation where the increase in the rough concentrate grade of 5% after pumping Tecflote S11 directly into the tank cell. The mechanisms for Tecflote’s selectivity towards sulfides are currently under investigation and will be discussed. Results of TOF-SIMS analysis will be presented, demonstrating the collector’s selective affinity to different mineral surfaces in flotation. INTRODUCTION The history of collectors used today started in 1882 when Zeise first made xanthates. It was first used in flotation in 1925 – Cornelius Keller’s first patent (Fuerstenau, Jameson, Yoon, 2007). Between 1928 and 1930 American Cyanamid filed 7 patents for dithiophosphate, including flotation and chemical synthesis of the reagent, the first of which was filed by Christmann in 1928 (Christmann, 1933). Synthesize of thionocarbamates for mineral flotation was filed in 1954, by Dow Chemical Company (Harris, 1954). Now that the head grades have been declining over the last decades the need to find more selective collectors to extract difficult and complex ores has pushed the industry to look at different chemistries. Thiol collectors standard to the industry rely on the sulfur in the collector molecule to bond to the mineral surface. The electronic property of this group is modified by the adjacent chemical groups, such as additional S, P or N have the effect of changing the selectivity of the collector (Wills & Finch, 2016). In the case of xanthate the length of the hydrophobic group also has an effect on the selectivity with some minerals such that the ethyl xanthate is more selective against pyrite and pyrrhotite than the long chain xanthates (Wills & Finch, 2016).

Jan 1, 2019

By K. V. Phani Prabhakar, G. Padmanabham1, L. Subashini

Laser-arc Hybrid Welding (LAHW) is a relatively recent concept which effectively combines the advantages of laser welding such as the high depth of penetration, low heat input, high welding speed and the positive aspects of arc welding such as better edge bridging and possibility to add filler. For example, steel sections upto 12 mm thickness have been successfully welded in a single pass at a welding speed of 1 m/minute using a 3.5 kW CO2 laser in combination with a MIG arc. Maraging steel of grade M250 is widely used in the aerospace industry in thicknesses upto 10 mm. Conventionally, it is possible to MIG weld such thicknesses in 3-5 passes employing V-Groove joint preparation. However, this multi-pass welding results in formation of reverted austenite in the weld zone after post weld aging; and the high heat input widens the reverted austenite containing heat affected zone which is popularly known as the dark zone/eyebrow zone. Both these zones are detrimental to strength of the welded joint, specifically the fracture toughness. The width of the dark band is an important factor because, thinner the band, it is supported more effectively by the surrounding material. Therefore, in order to avoid multi-pass welding and reduce the overall heat input, single-pass laser-MIG hybrid welding was attempted on 10 mm thick maraging steel M 250 plates using a hybrid laser arc welding system comprising a 3.5 kW CO2 slab laser and a MIG welding system. Simultaneously, multi-pass MIG welds also are produced. Both the laser-MIG hybrid and MIG welds are characterized microstructurally and subjected to mechanical tests such as tensile and fracture toughness in as-welded and post weld aged condition. The amount and distribution of reverted austenite in the fusion zone and width of the dark band was found to be different. Hybrid welds showed a narrow dark band zone and improved mechanical properties. Laser-hybrid and MIG welding investigations carried out on thick section maraging steel M 250 will be presented in detail, including microstructure, tensile properties and fracture toughness of the welds. To the best of the knowledge of the authors there are no reports on laser-MIG hybrid welding of maraging steels.

Jan 1, 2014

By C. J. Brown

Regeneration of hydrochloric acid steel pickle liquors has traditionally been accomplished by pyrohydrolysis. However, a number of factors have recently conspired to reduce the attractiveness of this approach. Moreover, the process is not amenable to small-scale operations. On the other hand, the standard technique for regeneration of sulfuric acid pickle liquors, which is the low-temperature crystallization of ferrous sulfate is applicable to any size operation. A similar technique has recently been developed to regenerate hydrochloric acid. Sulfuric acid is added to the ferrous chloride-bearing spent HCl pickle liquor. The temperature is then reduced to below 0°C, resulting in the crystallization of ferrous sulfate heptahydrate and liberation of free hydrochloric acid. Depending upon the crystallization temperature, variable concentrations of sulfate are left in the regenerated acid. Although this residual sulfate has an impact on the pickling characteristics of the regenerated acid, tests have shown that by adjusting the conditions, pickling rates will be at least equal to those using pure HCI, and an acceptable surface finish will be produced.

Jan 1, 2006

By Didier Fohlen

Three Policy Shifts to enhance IFC?s Accountability ? Comprehensive and dynamic treatment of social, health, safety and environmental risks ?Covers a range of risks encountered by clients in emerging markets ?Framework to anticipate risks and to address them as they arise ?Includes community development, biodiversity, human rights ... ? Effective principles to guide an outcomes-based approach ?By clients and IFC ?Focus on broad community support and value-added sustainable development initiatives Enhanced governance, transparency and disclosure

May 1, 2006

By M. J. Sapko, R. W. Watson, E. S. Weiss

The relative incerdivity of several blasting agents was evaluated in the Bureau's Bruceton Experimental Mine (BEM) . The minimum charge weights resulting in the ignition of predispersed oil shale dust clouds were measured for each of the explosives. A 400 g unstennned charge of ANFO (ammonium nitrate-fuel oil) was sufficient to initiate an oil shale dust explosion, whereas a 1000 g unstenuned charge of an emulsion blend did not ignite the dust even with the addition of 4% methane gas. Several stenuning materials were evaluated in the BEM for their effectiveness in preventing the ignition of near stoichiometric methane-air mixtures. Water stenuning was superior to all other inhibitors tested against methane. Explosibility testing of fine sulfide ore dust in a 20 L chamber and in the BEM show that the dust is capable of propagating an explosion given nominal concentrations of 700 to 800 g/m3. Results are encouraging and irrlicate that there is merit in pursuing explosive composition as a means of reducing ignition probability of oil shale and sulfide dust clouds generated during nonnal blasting operations. The proper selection of explosives and stenuning materials should significantly reduce the probability of secondacy dust explosions in oil shale and sulfide ore mining.

May 11, 1988

By C P. Gravenor

In 1953, a deposit of sedimentary oolitic iron ore was discovered in the Clear Hills area of northwestern Alberta. Since that time, detailed drilling has outlined reserves in excess of 200 million tons of ore grading 30 to 35 per cent iron. Attempts to physically beneficiate the ore to meet blast furnace or direct reduction feed specifications have been, in general, unsuccessful. In 1960, Premier Steel Mills Limited and the Research Council of Alberta jointly sponsored a pilot-plant test at the R-N Corporation at Birmingham, Alabama. About 5,000 tons of ore were treated, and briquettes containing 90 per cent Fe were produced, with 83 per cent recovery. At the same time that the R-N tests were being made, the Research Council initiated a program to produce high-purity powders by chemical methods. Several purification techniques were investigated; hydrochloric acid dissolution of reduced ore was finally adopted. Briefly, the steps involved in this acid process are as follow

Jan 1, 1964

By Bryan Tisch

Goal of GMGE ??To advance mine reclamation through the beneficial use of organic residuals for the sustainable establishment of bioenergy crops and other productive land uses Objectives ??To advance the current ?standard? of mine reclamation by demonstrating that mining lands can safely become agriculturally ?productive? through the use of organic residuals. ??To generate and compile sound scientific data that can be utilized by stakeholders to better assess the environmental impacts of utilizing these materials. ??To complete a manual of best practices regarding the utilization of organic residuals on mine lands. *Considerable effort to be placed on operations/implementation side of utilizing residuals ?rather than just pure research

May 1, 2011

By R. U. Seneviratne, B. K. Ahlgren

In this paper we follow various technological discoveries and developments in the purification of minerals and metals in the mining industry by ion exchange. For approximately 100 years, ion exchange has been a known and variously applied purification and separation technology used by scientists and producers. It would seem obvious that the producer’s objectives have always been to achieve the highest quality products and the lowest operation costs, but also with the least amount of technological complexity. As a strategy to reach these goals, much effort has been expended in the quest to improve continuous ion exchange (CIX) systems by reducing utility needs and resin degradation or loss while at the same time improving productivity and reliability. Recent developments from a number of companies have pushed equipment boundaries, resulting in a variety of unique commercial equipment designs each with a varying degree of success. The challenge set forth for all new designs has been a truly continuous process with no sacrifice in the afore mentioned benefits. One very recent equipment design based on system symmetry appears to meet many of these objectives with greater flexibility and less complexity resulting in better economics for the producer.

Jan 1, 2014

By Jing Chai

The Cenozoic unconsolidated strata with the thickness of 100 to 240m in the east area of China are composed of clay, sandy clay and hardpan, etc. Numerous shafts of the coal mines in these areas have been damaged to various degrees since 1987, with the main reason for this being the subsidence of the super-thick unconsolidated strata. To prevent the continuing settlement deformation of unconsolidated strata caused by groundwater removal, long-term water injection through multiple boreholes controlled the settlement deformation of unconsolidated strata. A new type of fiber Bragg grating (FBG) sensing system was successfully used for real-time strain monitoring of the unconsolidated strata during water injection at a coal mine in China. A mathematical model for the compression settlement induced strain calculation is proposed which can assist understanding of the effect of water injection on the ground. With the increase in water injection, the unconsolidated strata compressed state was improved by the transition of the stress state from compressive to tensile stress. The wavelength change of fiber Bragg grating sensors corresponded with the trend of the water level in the same strata. Engineering practice indicates that these sensors can normally, safely and reliably survive conditions associated with hydrous unconsolidated strata. The FBG sensing can be used for continuous lifetime monitoring of the system, starting with real-time monitoring during low-pressure water injection process of multi-borehole. The results will give important guidance for water injection and mastering stratum subsidence.

Aug 1, 2013

By P. K. Gummer

Gold was fir t di covered on the Seabee property in 1947 by the Con olidated Mining and Smelting Company Limited. Acquired by Claude Resource Inc. in 1984, the property is now being explored by Placer Development Ltd . in joint venture with Claude Re ources. Between Augu t, 1985 and March, 1986, Placer completed 54 drill holes, extending the main o. 2 and o. 5 vein y tern to a depth of 1000 feet below surface and di covering two new satellitic gold zone 800 feet west of the o. 5 gold zone. Drill proven and probable geological re erve in four zone ( os. 2, 5, II, 14) to a vertical depth of 1000 feet, are approximately 1,120.000 tons averaging 0.32 oz. Au/ton.

Jan 1, 1986

By John Hansen

This paper has been written for presentation at the 103rd Annual General Meeting of the Canadian Institute of Mining, Metallurgy, and Petroleum, April 29 to May 02, 2000. The paper addresses blast pattern fragmentation and diggability versus the blasting technique used. RESUME The author is the Vice President for Thunderbird Mining Systems. In this capacity he manages the mine site installation of surface mining mobile equipment monitoring and navigation systems. These systems are onboard instrumentation and software systems designed to: ??measure and log mobile equipments? production and health; and ??direct the equipment operators via onboard displays that show comprehensive maps and engineering instructions. The author is a mining engineering graduate from the Royal School of Mines. His work experience includes front line supervisor and mining engineer for Hudson Bay Mining & Smelting, mining engineer for Teck Corporation, and mining consultant for PriceWaterhouseCoopers.

May 1, 2001

By M. Al-Khawaja, F. Hassani, F. Mucciardi, N. Razavinia

"In today’s economy many industries are becoming aware of the need to recover some of the waste heat they create. Industrial processes release, on a global scale, over 100 tera-Joules (i.e. 1014 J) of waste heat annually. The recovery of waste heat can lead to a reduction of greenhouse gas emissions and it can also provide a financial benefit which can be obtained by converting some of this excess heat to electricity. At McGill, a research program has been initiated so that low grade waste heat (temperature between 100ºC and 300oC) from process off-gases found in pyro-metallurgical industries is captured and concentrated by using heat pipes and then converted to electricity by a mechanical engine. This paper illustrates the 3 C’s process (capture, concentrate and convert waste heat to electricity). It also provides some preliminary experimental data. INTRODUCTIONThe problematic climate change caused by the use of fossil fuels, the rapid depletion of global reserves and the catastrophic consequences of nuclear power generation call for renewable and safe, resources of energy, for both man and the environment. Extensive researches in the production of energy from renewable sources and improvements in efficiency of current technologies can help us to reverse this trend.The greatest advantages of using renewable energies are that they don’t deplete and they also contribute to a green environment. On the other hand the disadvantage of using these resources is that the energy available from renewable sources is much less concentrated than that provided by fossil fuels and nuclear energy. This makes renewable energy less attractive for large scale industrial uses in most cases. A key target for society for the 21st century is the production of energy from renewable sources at a cost that is competitive with fossil fuels. Fossil fuels represent a concentrated form of energy; usually it is referred to as high grade energy. Nonetheless, there is a vast supply of alternative energy. The sun, wind, water and biomass were the first to be explored. While these are all valid options that warrant concerted efforts and large investments, there is another source of energy that typically is produced by manufacturing industries. This energy is often referred to as low grade waste heat. Most of this energy is simply vented to the environment through the stream of off-gases. In the future it will be necessary to capture and convert some of the low grade heat to a valuable form such as electricity if we are to improve on the efficiency of energy usage."

Jan 1, 2012