Search Documents

By D. Bronkhorst, J. Rheault

"Backfill practices at the Williams mine have evolved significantly since underground mining began in 1986. The use of conveyors as a means of transporting fill material to stopes has been discontinued in favour of load-haul-dump equipment. The method of adding binder to the fill product has been refined along with the placement technique. Slurry preparation has been fully automated and flyash is now included as a binding agent. Surface preparation of the fill product has evolved substantially with the quarry operation coming into full operation and the construction of pennanent crushing, screening, and storage facilities. Company personnel have replaced all contracted labour involved in backfill operations. Some changes have been made to achieve a higher standard of quality control while others were implemented as a matter of cost reduction. BackgroundThe Williams mine is one of three mines operating at the Hernlo gold deposit, located 40 km east of Marathon, Ontario, along the north shore of Lake Superior. Daily production at the mine is 6000 Ud yielding an annual gold production of approximately 500 000 oz. The orebody extends from surface to a depth of 1300 m dipping north at 70 degrees. The average orebody width is 25 m, but varies from 45 m on the eastern boundary to about 10 m at the western probable limit and at depth. Proven and probable reserves currently stand at 32 million tonnes grading 6 g/t.The Williams orebody has been divided into four separate mining zones: the A-zone, the West-of-Dyke zone, the B-zone, and the C-zone (Fig 1). Ore production originally was from the A-zone open pit operation while the A-zone and B-zone underground workings were being developed. The mining method employed underground is blasthole open stoping with delayed rockfill. Mining block dimensions are nominally 20 m along strike by 25 m high. Stope extraction is sequenced to achieve a relatively short pillar life and 100010 ore recovery. Pillars are extracted as soon as the adjacent primary stopes are two cycles ahead. Primary stopes are filled with consolidated rock fill after mining. This allows pillars to be blasted right against the consolidated fill, but also requires that the fill be self supporting to a height of 30 m.The Williams mine places approximately 1.4 million tonnes of rockfill and 50 000 tonnes of binding agents each year, with about three quarters of the fill placed being consolidated. The consolidated fill placed at the Williams mine contains Portland cement and flyash as binding agents."

Jan 1, 1994

By Ross Gilders, Leo Cheung, C. David Desjardins

"For the past twenty years significant progress has been made in bacterial leaching. In fact, a recent article in the Northern Miner has cited that nearly all new copper production is based on bioleaching. The bacteria that play the predominant role in bioleaching is an obligate chemolithoautotroph called thiobacillus ferrooxidans. These bacteria thrive in areas rich in sulphide and prefer low acid media. In the simplest sense, they metabolize sulphide converting it to sulphate either as acid or as soluble metal sulphates. This process is well known because these bacteria generate acid mine water. Over the last five( 5) years, we have been carrying out development work on creating optimum bioleach conditions for the extraction of metals from sulphide rich ores and concentrates. Recently, a study was carried out on a byproduct sulphide concentrate produced in a tin flowsheet developed for the Mt. Pleasant Mine of ADEX Mining Corp. The objective was to determine whether a bioleach process might successfully leach this sulphide material which contains copper, zinc, iron and, what is more important, trace metals such as Indium, Gallium, and Bismuth. The current work describes the successful recovery of these metals achieving extractions of more than 80% by applying bioleaching techniques. An overview of this technical program forms the basis of this paper.IntroductionBio-Oxidation of metal sulphides has emerged to be one of the leading edge hydrometallurgical processes for the economic extraction of metals from ore and concentrates. The fundamental process involves the bacterial assisted oxidation of sulphide to sulphate yielding metal sulphates which can be subsequently leached by conventional means. The bacteria that play the predominate role is an obligate chemolithoautotroph named thiobacillus ferrooxidans (TF). These bacteria thrive in areas rich in sulphide and occur naturally worldwide. In fact, TF is responsible for generating acid in water (acid mine water) from exposed sulphide surfaces primarily through the oxidation of pyrite. TF bacteria thrive under the proper conditions of temperature and oxygen supply in the presence of sulphides and populations in excess of a million per millilitre (ml) of solution are achievable. Typically, at room temperature, the bacteria will bio-oxidize in a pH range of 1.0 to 3.0. Today, bio-oxidation has been applied commercially with great success for the extraction of uranium, copper, and gold."

Jan 1, 1996

By W. A. Jones

THE estimation of the average value of gold ore involves many considerations, among them the correct sampling of the deposit, the dilution by waste, and the loss of high-grade fines. It is a common experience that, after all these factors have been evaluated, adjustment of the assays is necessary before satisfactory agreement between the calculated mine grade and the mill heads is obtained. In fact, at many mines the latter correction overshadows all others in the preparation of routine estimates. For this reason it is proposed to deal only with the mathematical treatment of mine assays and the problem of bringing estimates into conformity with the corrected mill heads. Mine assays differ from physical measurements because the range of values is very great and these are not symmetrically distributed above and below the average, there being fewer high than low results. There is no widely accepted mathematical procedure for determining the average of series of measurements which exhibit these characteristics. Customary practice consists in empirically reducing high assays until a satisfactory agreement with mill heads is reached. It was thought that more confidence could be placed in grade estimates if a logical basis for calculations could be devised .. In an attempt to find a fundamentally sound procedure, amenable to practical application, many series of assays comprising over 235,000 channel samples (1) were studied at Hollinger Consolidated Gold Mines, Limited. Such an investigation could only be made where records covering many years of operation are available and where tabulating and calculating machines are in use. The results are recorded in the hope that the relationships noted for the large groups of assays used are of fundamental character and that the data will be useful to others dealing with the problem of grade estimation.

Jan 1, 1943

By M. Muinonen, R. Pandher

Royal Nickel Corporation is developing the Dumont Nickel Project, a large nickel sulphide deposit located near the town of Amos, Québec. The nickel occurs as pentlandite, heazlewoodite, and awaruite. The relatively low grade ore can be processed to a very high grade nickel concentrate, containing 29% Ni. The absence of copper and precious metals in the ore renders this concentrate amenable to processing by dead roasting in a fluid-bed roaster and smelting in an electric furnace to produce ferronickel for sale to stainless steel producers. Laboratory test work and conceptual engineering design was completed to demonstrate the amenability of Dumont concentrate to produce ferro-nickel.

Jan 1, 2015

By Maarten van de Vijfeijken, Marco Rufli

"By using the latest generation of medium voltage frequency converters, new possibilities have arisen to improve the grinding process. Beside all the direct and indirect advantages, several dedicated functions have now been implemented for ring geared grinding mills in the minerals industry. The advanced operational functions ensure a smooth, safe and reliable operation with minimum stress for the mechanical equipment and therefore highest availability of the mill. Several papers have already been presented concerning the benefits of using this state of the art technology for mill drives (Ravani von Ow and Bomvisinho, 2010; Ravani von Ow and Gerhard, 2010). However this paper will not only show and explain the operational benefit of these functions, but will focus on the experiences gained with this kind of sophisticated ring geared mill drive system. Several measurements of different operating conditions (starting, frozen charge remover, controlled roll back, backlash, etc.) made on an installed and commissioned 2 x 5 MW dual pinion ring geared mill drive system will be shown and discussed. Also the accuracy of the load sharing between the two 5 MW motors during starting, normal operation and stopping will be demonstrated using real measurements from an operating system. Finally the inherent features of these drive systems are briefly discussed.INTRODUCTIONLooking at the demands of grinding mills, we can split them into operational, maintenance and protective demands. For smooth and safe operation, it is important that critical situations are avoided as much as possible. Maintenance functionality must be quick and easy to execute, while protection of the system is important during all operating conditions. ABB has considered all these demands during development of their dedicated mill functions. By adding an additional controller (mill controller), not only a lot of application related functionality and protection is included, but also the interface between the mill drive system and the customer’s distributed control system (DCS) is simplified."

Jan 1, 2011

By Fred A. Webber

STEEL ROPE WIRE is one of the more specialized commodities among the many grades of highcarbon steel wires. In its production there are many metallurgical aspects of interest from the steelmaking on through the final stages of wire drawing. We produce rope wire in an integrated mill com prising all the operations from the blast furnaces to finished wire drawing in the wire mills. Steelmaking is carried out with close control on hot metal, selection of scrap, and fluxing materials. The basic open hearths are of 170 tons capacity. Steel is teemed into 19 1/2 in by 19 1/2 in big-end-down molds and is hot-topped with the use of clay refractory hot-tops. The weight of this ingot is 6,900 pounds. All high -carbon steel ingots are charged hot into the soaking pits and are then rolled through the blooming mill in 16 p asses to a bloom ax~ in. by 41/2 in. and approximately 65 feet long. Necessary bottom and top crops are taken on the bloom as it passes from the blooming? mill to the billet mill. The still hot bloom is continuously rolled through the billet mill in . 5 passes to a 2 3/8 in. square. Billets are cut to 32 feet in length by a flying shear and then allowed to cool on the hot bed.

Jan 1, 1957

By Jay F. Colinet

Researchers at the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) work to reduce respirable dust exposures in mining operations. One focus of this research is silica dust control for surface and underground operations in the metal/nonmetal mining industry. PRL researchers analyze dust sampling results from the Mine Safety and Health Administration (MSHA) to identify high-risk occupations to guide research efforts. Research is then conducted in an effort to improve existing technologies and/or develop new controls for reducing worker exposure to airborne silica dust. During the last few years, PRL researchers have conducted research related to the following goals: improving protection provided by enclosed cabs on mobile surface mining equipment, reducing dust generation from surface drills, reducing dust levels in iron ore operations, and developing a new method to clean dust from workers? soiled clothes. A description of each of these controls and subsequent dust reductions quantified through site surveys will be provided.

May 1, 2007

By William J. Davis, R. Blair Hrabi, Sally Pehrsson, Amelia V. Logan, Ross Sherlock

"Abstract - The Meadowbank gold deposits are hosted by a series of polydeformed and metamorphosed auriferous iron formations located in the Neoarchean Woodburn Lake group, western Churchill province, Nunavut. The supracrustal rocks in the Meadowbank area consist of a thick sequence of intermediate-composition volcanic rocks with intercalated iron formation, ultramafic volcanic rocks, and quartzite to quartz arenite. U-Pb geochronology gives an interpreted age of 2711 ± 3 Ma for the host strata at Meadowbank.The intermediate volcanic rocks are predominately volcaniclastic and have a geochemical composition that is consistent with an active continental margin setting. Iron formation deposition was coeval with the intermediate volcanism, as indicated by incorporation of volcanic detritus in the chemical precipitate. The geochemistry of the iron formation indicates that it precipitated from a fluid that at one time was at high temperature (>250°C), reducing, and likely acidic. Intercalated ultramafic rocks rarely show spinifex textures and have trace element ratios that are consistent with mantle plume-related undepleted mantle asthenosphere, likely recording episodic mantle upwelling associated with rifting in an active continental margin. The contact between the ultramafic volcanic rocks and the overlying quartz arenite is a disconformity marked by a quartz pebble conglomerate. However, similar geology on the structural hanging wall and footwall of the contact suggests that the conglomerate does not represent a significant hiatus in deposition, and is more likely a prograding terriginous siliciclastic unit.Three metamorphic events are recognized. The first, M1, is a cryptic greenschist facies event that is pre-D2. The second event, M2, is a mid-greenschist to amphibolite facies, syn-D2 event. M3 is the last event recognized, and is a post-tectonic greenschist facies event that is regional but inhomogeneous in extent, possibly reflecting thermal aureoles around post-tectonic 1.7 to 1.8 Ga Nueltin granites. The structural geology of the area is complex with four phases of deformation recognized, two of which had a significant effect on the geometry of the deposit. All of these regional events are interpreted as Paleoproterozoic in age. Relationships between deformation fabrics and mineralization, as well as the overall geometry of the mineralized envelopes, suggest that the deposit formed during syn- to late-D2. Superimposed on the mineralization are D4 structural elements that postdate gold mineralization.The main control on gold mineralization is replacement of magnetite by pyrrhotite and pyrite in high-strain corridors. The composition of amphiboles and chlorites associated with gold mineralization is remarkably consistent and shows no spatial or temporal variation, suggesting that it was buffered by the iron-rich nature of the host rocks. The bulk metasomatic effect on the intermediate volcanic rocks is characterized by the addition of K2O and the loss of CaO, Na2O, and MgO, with little variation in the total iron content. The elemental losses are likely the result of destruction of feldspars, stilpnomelane, and ferroactinolite, which are relatively common in the unmineralized rocks, and the formation of sericite, chlorite, and grunerite."

Jan 1, 2004

By J. Molgaard, J. Masounave, J. Prinsen, P. Beaulieu, G. Huard

"A study carried out on behalf of the National Research Council (NRC) indicates that economic losses due to wear in the Canadian mining industry are in excess of $700 million annually. Severe wear, mainly by abrasion, was identified as the most important wear mechanism in terms of possible savings. One way to reduce losses would be the proper use of databases. A joint project of The Canadian Institute of Mining and Metallurgy (CIM) and NRC (Tribology laboratories at IMRI) has been initiated to create a factual database containing all relevant experience in the area of wear in the Canadian mining industry. As a first step, a prototype covering slurry pumps is being built. This should help to answer many questions, such as the number of people involved, interest from industry, cost vs benefits, etc.IntroductionTribology is concerned with the understanding of the mechanisms of friction, wear, and lubrication.Tribology is concerned with the correct use of materials for interacting solid surfaces, with the interaction of those surfaces with lubricants, with the chemistry, physics and use of lubricants and their additives. It is concerned with the reduction of friction and wear (or, in the case of belts, brakes, clutch plates, and similar devices, in achieving optimum friction with minimum wear) and is concerned with the avoidance of associated failures in machinery.Lubrication is usually the solution to a problem of friction and wear. Yet far from all the problems of friction and wear are solved by lubrication. The wear of grinding rods or shovel track pads can hardly be solved by lubrication, to name just two examples with which mining engineers will be familiar. There are indeed many situations of wear and friction where the surfaces in contact are unlubricated.In part, tribology is a matter of design. A major aspect, however, has to do with the choice of materials, to satisfy external constraints upon the component design or choice. The operating conditions for much industrial equipment, particularly in mining are, often very severe. The development of wear resistant materials, including materials which are applied as coatings, is clearly an important technology from the point of view of tribology."

Jan 1, 1987

By Peter Barker, Terry Jones

"The Kelsey Centrifugal Jig (KCJ) utilizes the application of centrifugal force (and the resultant enhanced gravitational field) to conventional jigging technology principles to successfully and efficiently process materials where the valuable constituent particulates are very fine and/or where there is a small specific gravity differential between these and the gangue minerals.The KCJ is applicable to a broad range of fine mineral recovery duties, with current installations in the mineral sands, tin, tantalum, gold and nickel industries. Other areas of application are being developed with mineral commodities including tungsten, base metals, iron ore, chromite and apatite/feldspar.Information on the principles of operation of the KCJ, typical performance figures in a number of application areas, comparison to centrifugal concentrators, key elements for a successful KCJ operation and recent developments with the KCJ are presented in this paper to demonstrate the capabilities of the KCJ.INTRODUCTIONAfter a number of years of development by inventor Chris Kelsey, the first commercial KCJ unit was installed at the Renison Bell tin mine in Tasmania, Australia, in 1992. The subsequent decade saw the installation of further KCJ units in applications including tin, tantalum and mineral sands.Development and improvement in KCJ hardware continued and culminated in the introduction of the high-capacity Model J1800 KCJ and standard features such as an automatic screen cleaning system. This opened up further markets and resulted in Model J1800 KCJ installations in the gold and nickel industries, as well as further KCJ installations in the mineral sands and tin industries. In recent years, work has continued on application of the KCJ to many other duties in industries including tungsten, base metals, iron ore, chromite, apatite/feldspar, etc."

Jan 1, 2007

By Arthur L. de Carle

"IntroductionThe Key Lake uranium-nickel deposits are located within a Mineral Lease centred at latitude 57 ° 12' north and longitude 105 °39' west along the southeastern rim of the Athabasca sedimentary basin in northern Saskatchewan, approximately 240 km north of La Ronge (Fig. 1). Access is provided by an allweather provincial highway from Pinchousc, situated about 200 km to the south, and a private airstrip maintained at the mincsitc.These deposits have been developed by Key Lake Mining Corporation on behalf of the Saskatchewan Uranium Joint Venture. Participants in the joint venture include Saskatchewan Mining Development Corporation (50%), Urancrz Exploration and Mining Limited (33 1/3 %) and Eldor Resources Limited (16 2/3 %).Considerable geological work has been conducted on the Key Lake orebodies and reported in summary papers published by Dahlkamp and Thn, (1977), Dahlkamp, (1978), Gatzweiler eta/., (1979) and Kirchner el a/. , (1980). However, intensive geological research is ongoing, particularly since many problems regarding ore genesis and controls remain unresolved . Exploration History and DevelopmentThe events (Gatzweiler eta/., 1980) which led to the discovery of the Key Lake ore bodies began in the summer of 1971 by following up on the reports of airborne radiometric anomalies and anomalous radon values in the Zimmer Lake water situated approximately 5 km to 6 km to the southwest. This work succeeded in locating a few high-grade uranium and nickel-bearing boulders associated with esker material. An integrated program, consisting of various geochemical and geophysical surveys along with diamond drilling, culminated in the discovery of the Gaertner orebody during July 1975. Subsequent fence drilling across the strike extensions of this ore structure located the Deilmann deposit, approximately I km to the northeast, in June 1976"

Jan 1, 1986

By C. Rodgers, E. (Ted) Warren

"LocationThe Key Lake operation of Cameco Corporation is located at latitude 57°N in northern Saskatchewan, within the southem boundary of the Athabasca formation. The nearest city is LaRonge, located 240 km to the south. Access to the mine is by all-weather road and by private airstrip.Description of OperationThe mill was designed to produce twelve million pounds of uranium oxide (U3O8) a year from a feed grade of 2.4% U3O8. Current production is fourteen million pounds from 2.0% feed.Following grinding, the uranium is leached using sulphuric acid and oxygen in autoclaves. An eight thickener counter current decantation (CCD) circuit is used to separate the uranium-bearing solution from the solid waste residue. The uranium in solution is further purified in a solvent extraction circuit. The purified uranium is then precipitated using ammonia, calcined at 840°C, and packaged in drums for shipping to refineries. There is a crystallization circuit to recover excess ammonium sulphate produced in the process, and a waste treatment circuit.HistoryUranerz Exploration and Mining discovered the Gaertner and Deilmann orebodies in 1975 and 1976, respectively. Between 1975 and 1977, Uranerz conducted laboratory studies and delineated a process for the Key Lake ore known as the ""Bonn process."" In 1977, Sherritt Gordon Mines Ltd. was retained to conduct further studies in cooperation with U ranerz. The technical feasibility of the Bonn process was generally confirmed. Howeve1~ alternative processing methods also appeared feasible, and over the period 1978-1979, a detailed research and development program was conducted to finalize the processes to be used and to provide data for design of the plant."

Jan 1, 2000

By Matthew A. Perras

With growing populations, infrastructure projects are utilizing underground space to expand transportation networks, water supply and sewer disposal systems and hydropower facilities. These new projects require large diameter tunnels to meet the growing demands. As the tunnel diameter increases, not all rock mass properties are scalable and precedent experience becomes less reliable. One such non-scaleable property is lamination thickness. Numerical modelling was conducted to determine the influence of lamination thicknesses on a 16 m diameter tunnel. Five different areas of excavation response were found to exist for laminations ranging between 0.16 to 16 metres in thickness. For this tunnel diameter, critical lamination thicknesses of 6 metre and 1 metre were found to exist. Above 6 metres the excavation response was similar to isotropic models. Below 6 metres the stresses and yield are channeled by the lamination boundaries, increasing plastic deformation. Below 1m multiple lamination units become unstable and the displacements increase significantly and the shape and extent of the yield zone size changes dramatically. The yield zone is controlled by bed deflections and bed parallel shear. As the lamination thickness decreases tensile failure first begins in the haunch area and progressively extends above the crown until a self-limiting plastic yield zone shape is reach at lamination thicknesses below 0.4 metres. Conclusions drawn from observations at the Niagara Tunnel Project are those of the authors.

May 1, 2009

By Francoi Robert, Andre J. Audet, Alex C. Brown

"The Sigma gold deposit is in a band of deformed metavolcanic rocks that are cut by an irregular mass of porphyritic diorite and by narrow undeformed feldspar porphyry dykes. The gold is in veins consisting mainly of quartz and tourmaline with minor pyrite, carbonate, chlorite, scheelite and free gold. The results presented here concern the structural setting of the ore and are based on a study of the mode of emplacement.Two principal types of veins have been recognized: subvertical and oblique veins. Both types are contemporaneous, mechanically linked and postdate regional deformation. The sub-vertical veins are composed of numerous mineralized lenses that occupy the central part of ductile shear zones of great lateral and vertical extent. Normally, several lenses occur in the same shear zone. The vein material seems to have resulted from incremental filling of openings by repeated vertical movement along rupture planes developed in the central part of the shear zones.The oblique veins are small elliptical lenses of ribboned vein material which formed essentially by progressive vertical opening of oblique fractures. Two types of oblique veins are known: one is restricted to feldspar porphyry dykes, within which they are arranged in an en-echelon fashion; the other is of greater extent and is not restricted to one rock type, but tends, however, to occur in the more competent porphyritic diorite.Vein orientation and mode of formation suggest that both sub-vertical and oblique veins developed during progressive deformation associated with the formation of the ductile shear zones. The latter probably formed in response to a compression that took place late in the tectonic history of the host rocks at Sigma."

Jan 1, 1983

By S. Nikolic, G. M. Stieper, D. P. Mallah, B. J. Hogg, P. B. Voigt

Copper feed materials processing is becoming more challenging, due to an incremental increase in the mineralogical and compositional complexity of these feeds. These complex and polymetallic feeds are now becoming more common and many sites have been forced to re-evaluate their operating strategies to process these materials at cost competitive rates, whilst meeting ever more stringent environmental regulations. Most operations must first evaluate the merits of pyrometallurgical and hydrometallurgical treatment routes. Although there are multiple copper smelting technologies available, only top-submerged lance (TSL) technology, supplied by Glencore Technology as ISASMELT™, has been applied in the real world to consistently and successfully smelt complex materials in integrated metallurgical facilities such as Glencore’s Kazzinc Ltd. operation in Kazakhstan, Umicore Precious Metals Refining in Belgium and Aurubis AG in Germany. Glencore Technology also offers hydrometallurgical processing, through the Albion Process™ technology, opening up viable flowsheet options previously not possible for these complex feeds. This paper describes a number of real world process flowsheets at global operations and Glencore’s own operations at Mount Isa and Kazzinc Ltd., which process complex feeds. These flowsheets integrate the ISASMELT™, Albion Process™, ISACONVERT™, ISAKIDD™ Tank house, and bottom blown oxygen cupel (BBOC™) technologies to provide an effective process solution for the treatment of complex polymetallic feeds to produce metallic copper and associated by-products. INTRODUCTION Traditional smelters and those built in recent times within the bulk smelting hubs of the world have been designed to treat standard/clean concentrates. In recent years the processing of complex polymetallic sulfide concentrates and the recycling of secondary copper and derivatives of waste electrical and electronic equipment, such as e-scrap, have become a focus for numerous companies (Alvear & Nikolic, 2013). Processing of these complex feeds, characterized by relatively high levels of minor elements (over 5% of elements such as arsenic, antimony, bismuth, lead and zinc) is more challenging. Facilities not designed for these types of materials may require significant modifications or a change in smelting technology to treat them. Often operations find themselves re-evaluating the merits of pyrometallurgical and hydrometallurgical treatment routes for their sites through a number of factors:

Jan 1, 2019

By R. A. Nemchek

Over the years, concentrator plant design has evolved from a large number of small grinding mills to a small number of large mills. In many cases, all of the tonnage runs through a single mill (typically a large SAG mill), so that the plant’s performance hinges on the productivity of this one machine. Industry specifications attempt to address the critical nature of today’s grinding mills in a manner that is often overly complex, neglects economics, and is not clearly focused on the end user’s goals. This paper surveys current industry practices, and proposes an improved approach to standards writing recognizing that product design, procurement, manufacturing, and quality are all inter-related in contributing to a project’s success. The lessons learned here can be extended to specifications for all types of machinery.

Jan 1, 2012

By Vicki Tschirhart, Bill Morris, McMaster University

A new method for mapping faults within basement rocks underlying the Thelon Formation and glacial overburden was developed and tested in the Aberdeen Sub-basin. This method utilizes newly acquired aeromagnetic data, the Blakely algorithm for defining magnetic source edges, a calculated dip-direction map, a digital elevation model (DEM) derived from the Canadian Digital Elevation Database, and the positions of identified, inferred and newly mapped faults that are within and adjacent to this sub-basin. Combining these data revealed three age groups of faults. One group is seen only on the DEM; these faults are young brittle structures that have no effect on the sub-Thelon basement unconformity, and are not visible on the dip direction map. A second group is evident on the dip direction map but not the DEM; these faults are old basement structures that did not propagate upward through the Thelon Formation. The third group is expressed on both the DEM and dip direction map; these faults are also old structures that propagated upward during and/or after deposition of the Thelon Formation. The latter group of faults may be of greatest interest for uranium exploration, with reactivation increasing their potential to serve as conduits to transport uranium-rich fluids and focus deposition at or near the unconformity surface. This methodology has promise for comprehensive mapping of basin faults and tracking the tectonic development of the whole Thelon Basin through time.

Jan 1, 2013

By Sunil Koppalkar, Liming Huang

"Since late 1980s the research group led by late Professor Andre Robert Laplante at McGill University undertook fundamental studies and applied research of the Knelson Concentrator (KC) and developed a sustainable method to correctly estimate gravity recoverable gold (GRG). In the early time a concept of ‘free gold’ was used, it was defined as the gold that could be separated and recovered from gold ore by amalgamation. Due to health and safety hazards, its practical use had declined. Around 1994, a methodology using a 3-in Knelson Concentrator to measure gravity recoverable gold was established at McGill University. Through more than 10 years’ improvement and optimization, this technique had become a standard method to evaluate GRG for gold ores, gold plant streams and platinum group metals. Until 2006, about 200 GRG tests had been carried out at McGill University for the ores from all over the world. Recently, a modified version of GRG test (short test) with the advantages of reduced processing time and lower cost had been developed for the mundane needs of gold industry.INTRODUCTIONGold gravity recovery has evolved significantly over the past twenty-five years, mainly because of the advent of the Knelson Concentrator (Knelson 1988, 1990, 1992, Laplante 2000). Now, a series of Knelson Concentrators for different applications are manufactured and used in gold industry all over the world (Knelson Concentrators 2004).In 1980s the Knelson Concentrator gained acceptance from mining industry as an effective device for the recovery of gold from grinding circuit. Knelson Concentrator became the obvious choice because of its design features: a relatively long processing time without concentrate discharge (compared to some other centrifuges, such as Falcon Concentrator and Chinese Yunxi Centrifuge at that time), large throughput capacity, treating a wide size range of material, yielding a high grade concentrate with small mass that could easily be smelted. As more and more Knelson Concentrators were accepted in gold industry, mineral processing engineers faced with challenges: what are the separation mechanisms of the Knelson Concentrator? How much gold can be extracted for an ore if a Knelson Concentrator is installed? For answering these questions, a laboratory scale Knelson Concentrator was created."

Jan 1, 2007

By C. Anderson, H. Huang, P. Miranda, E. Dahlgren, I. Chandra, M. Jeffrey

The latter part of the 20th century saw great advances in the treatment of refractory gold ores coupled with increased reliance on the use of cyanide for gold processing. Now, in many parts of the world, there is social pressure to limit or eliminate the use of cyanide. As well, treatment of some refractory ores or concentrates which have excessive cyanide consumption, gold cyanide pregrobbing or significant sulfide content remain difficult. This paper will outline the history of the development of alkaline sulfide leaching as an ancillary process to nitrogen species catalyzed (NSC) pressure leaching. Electrochemical fundamentals and the applicable thermodynamics of the alkaline sulfide hydrometallurgical system will be outlined. As well, examples of refractory gold recovery with alkaline sulfide hydrometallurgy such as an arsenopyrite gold concentrate application, a chalcopyrite gold concentrate application, a pregrobbing gold ore application, and a cyanide consuming gold ore application will be delineated in this paper.

Jan 1, 2005

By H. J. Ni, M. Y. Huang, S. W. Chen

The effects of several fluxes on purification, microstructures and properties of A00 aluminium have been studied. The experimental results and analyses indicate that many cracks and large porosities exist in the surface film above the melt purified by C2Cl6 and that the film is floe and mostly composed of AhO3 and pure aluminum, which carries many carbon particles and AlCh not fully volatilized. And then over 50% of the all-melting residue is pure aluminum, which is one of the major reasons for high melting loss. Moreover, because of a mass of gas bubbles and a state of seethe, there exist many inclusions which size is under l0µm in the microstructure of A00 aluminum purified with C2Cl6 or fluxes containing C2Cl6- With this purifying method, the aluminum crystal grains are extended along the radius that was observed firstly and the average crystal size of A00 aluminum are about 100µm~150µm. In addition, small size inclusions have little affected on tensile strength and micro inclusions under l0µm have little affected on elongation.

Jan 1, 2006