Search Documents

By Yosuke Ota, Makoto Tawara, Tetsuya Kojima

"Dry-lube has been used in Europe to enhance formability of aluminum sheet for automotive applications, but it is difficult to ensure degreasing performance with lower degreasing bath temperature. However, newly developed, highly lubricating pre-coats utilizing a urethane resin, which is soluble in water, have been found to show excellent degreasing performance. Furthermore, a richer pre-coat weight coincides with a lower friction coefficient and better formability. Combined use of anti-rust liquid oil showed different friction coefficient depending on applied surface pressure.INTRODUCTION The global demand for aluminum alloy products, especially for automotive application, has been increasing because aluminum alloys can offer excellent corrosion resistance with good strength and low density compared with steel. Aluminum alloys can contribute to saving much more energy and greenhouse gas emissions over the lifetime of the product. On the other hand, the amount of aluminum alloys in vehicle architectures is still somewhat limited due to relatively low formability. As a consequence of this low formability, it is necessary to set a certain limit to the shape of an aluminum alloy panel for automotive applications. So far hot melt wax dry lubricants have been in use especially in Europe as they have been recognized to provide better lubrication than conventional rust protection oils (Meiler & Jaschke, 2005). The benefit of hot-melt wax for automotive manufacturing is associated with a more stable forming process and the possibility to avoid extra lubrication in the press shop. But because of the low poorer solubility of hot-melt wax in degreasing aqueous bath solution, a higher degreasing temperature is required so that no remnant of hot melt wax can be carried over to the next manufacturing process. This temperature control is difficult to impress upon a manufacturing degreasing bath originally designed for liquid oil, especially in Japan. The typical temperature of degreasing bath in Europe is around 60°C, while it is only around 40°C. in Japan. Various types of pre-coats other than hot-melt with high lubricity have been reported (Tawara, 1993; Ueda, Hatsuno & Totani, 2013), but a balance between sufficient degreasing performance and high lubricity has not yet been achieved for an actual production process line."

Jan 1, 2018

By Chuck Crowell

ISO Standards ?Provide Information to Address Commercial and Safety Needs for Standardization: ?Definitions and Terminology ?Test Methods ?Performance Criteria ?Conformity Assessment Process ?Developed by Global Experts ?Promote Global Harmonization

May 1, 2013

By Joanna LaForte

"IntroductionIn respect to The Human Dimension by M. Phyllis Bray, this author's impression is that research on long distance commuting (LDC) is long overdue. This type of mining is not new to many workers, especially those from areas such as the Maritimes, who have had to look for work away from their families for at least a decade. Perhaps to the industry the over-all set-up is new, but to workers who have faced mine shut-downs in their areas finding a job was the main objective and if the security of long-term employment was evident, then the families might join them later. This was the situation with which the writer' s family was faced.LDC LifestyleBeing the wife of an underground miner, the author has personally experienced this lifestyle for almost 10 years, and has never experienced accommodation in a company town. The first five years of marriage were spent in a small rural municipality within 50 miles of the worksite, but the town had industry separate from mining and was not affected by the mine shut-down.Since her LDC lifestyle began her family has been pretty much city-based, out-of-province commuters with two children and a third to arrive some years later. She therefore lived a fairly normal married life with a husband home daily. The author has experienced life with a husband who worked away for five-day stretches and then drove long distances to be home weekends or the portion of time left over from driving and fatigue. She has done the 3D-days in/l4-days out routine, and for approximately the past four years has been existing on a two-weeks in/two-weeks out ritual .The author does not agree that the ""bottom line is that mining families go where the jobs are"" . The miners go where the jobs are and the families fend for themselves with the assistance of the pay cheque making it home each pay period.Perhaps because there are many personal frustrations with this type of lifestyle, perceptions may be inaccurate. Having only dealt with underground operations, there may be gross differences between the pressures and demands of other forms of mining."

Jan 1, 1991

By A. Allaire

The Goldex operation of Agnico-Eagle Mines (AEM) commenced operations in the spring of 2008. Following some months of initial operation, the grinding circuit capacity was under-performing according to the original design throughput. BBA Inc. (BBA) was commissioned, in February 2009, to study the different options and recommend the quickest and most cost-effective solution to increase the grinding circuit throughput rate. The mandate was to increase the throughput of the grinding circuit to beyond the original design of 7,000 tpd to 8,000 tpd or greater, while retaining the existing SAG and ball mills. The circuit was modelled using JKSimMet software to evaluate the different options, each with a number of different operating parameters. The option of secondary crushing of the SAG mill feed was retained. Comparison of the different options and simulation outcomes, design of the secondary crushing circuit, operating conditions, and initial adjustments in the design and operating results of the new grinding circuit are discussed in this paper.

Jan 1, 2012

By Jacques Deraisme

The technology of percussion drilling is well mastered. The lower cost of percussion drilling allows more holes to be drilled for the same budget. However significant differences are often observed between percussion and diamond drill assay data. This is due to the increased level of contamination associated with the percussion drilling process. Statistical studies on twinned drillholes show that diamond and percussion assays cannot simply be merged in a traditional kriging approach. The question then arises on how to use both types of data to produce reliable resource estimates. To take into account the lower reliability of the percussion assays, a noise characterized by a variance is added to these data. The methodology consists of two steps: 1. Cokriging of the equivalent diamond value at the percussion assay locations. 2. Block kriging using diamond assays and equivalent diamond values, calculated previously, adding to these data a noise, whose variance is the cokriging variance of step 1. This particular way of achieving kriging is called kriging with variance of measurement error. The paper illustrates this innovative methodology with an application on an iron deposit. The results of this method is compared to block kriging using only diamond assays and the gain in precision is quantified. An extension of that approach to multi-element cokriging is also presented.

Oct 1, 2009

By J. A. Allan

"The history of the development and application of controlled recirculation systems in U.K. collieries is traced and the theory behind such systems briefly examined. Specific applications for dealing with dust and dust/heat problems in headings, for which practical experience is currently available, are described. Consideration is given to the special features which these systems introduce in the underground situation and to the essential safeguards which are required for their safe use.IntroductionRecirculation of air is a commonly used technique in genera l ventilation and air conditioning practice, but has always been regarded with some suspicion for mining applications. This is perfectly understandable in view o f the hazardous conditions which can occur with dangerous forms of recirculation in mines. However, certain controlled recirculation techniques can offer advantages, particularly in the field s of dust and climate control in headings, provided that they are designed, Installed an d managed with full comprehension o f all aspects of the system and always bearing in mind that from the point of view of serious firedamp ignition risk, headings are potentially the most hazardous places in coal mines.BackgroundProbably the first recorded use of deliberate recirculation in British collieries was reported by Lawton in 1933. This researcher described trials, undertaken under the auspices of a national committee on ""The Control of Atmospheric Conditions in Hot and Deep Mines"", involving attempts to increase the velocity, and thereby the cooling power on hot faces, by means of simple recirculation systems using fans and ducts delivering recirculated air in the opposite direction to the normal face airflow. No significant cooling advantage was obtained and there is no subsequent record of this work being continued. During the discussion on this paper, there was considerable disbelief that fire damp percentages had not increased significantly when air was recirculated, but apparently no attempt was made to establish why this should be. It is of interest to note that J. Ivon Graham, one of the contributors, recommended that recirculation should be tried in stone headings for the control o f dust, as he believed that ""there may be scope for recirculation and filtration of the air under certain circumstances in such headings"". This idea was not developed for another forty years."

Jan 1, 1983

By J. S. Scott

"The Quemont property comprises 640 acres lying directly north of and adjoining the Noranda (Horne) mine. During 1926 to 1928, United Verde Extension Mining Corporation sank a shaft 235 feet and did 3,000 feet of development work on the 215-foot level. Between 1929 and 1930, Quemonr Mining Corporation deepened the shaft to 926 feet, and did further lateral work and drilling on the 500- and 900-foot levels. This work was confined to an area close to the south boundary and met with little encouragement.Following a period of idleness a magnetic survey was made in the winter of 1944, followed in the summer of the same year by some 6,000 feet of drilling. The first successful hole was drilled in February, 1945, from the ice of Osisko lake.To the time of writing, 131,000 feet of drilling, surface and underground,have indicated a large tonnage of gold-silver-copper-zinc ore, and although some knowledge of the geology and structure is emerging, it is too early to draw definite conclusions. The following brief description deals only with those structural features that are reasonably well indicated."

Jan 1, 1954

By Pieter van Nierop

Outline ? What is gasification? ? Gasification Technologies ? Gasification ?The early years ? Gasification ? The last decade ? The Alberta Situation ? The Importance of Gasification in Alberta ? Polygeneration ? Development ? Conclusion

May 1, 2004

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, P. Ghobadi

Design and selection of equipment for a grinding circuit strongly depends on the mill function, ore properties and requirements of the down-stream circuit. Primary mills usually work in open circuit and size distribution of product would be controlled in the final steps using a classifier like cyclone. Although HPGRs are mostly utilized as pre-grinding mills, it is preferred to utilize them in a closed circuit due to their specific mechanism of comminution. Unique mechanical design of HPGR and its completely different crushing process than tumbling mills needs precise consideration on its circuit design. In this paper, we investigate the impact of different parameters on design of pre-grinding HPGR circuit and selection of the proper classifier. Our study focuses on iron ore properties (e.g. moisture, particle size distribution of feed and product, compatibility and de-agglomerability). We also investigated various options of HPGR circuit according the classifier efficiency and influences on down-stream processes. The optimum operating parameters of HPGR (working pressure, speed and level of hopper) for the selected circuit were also determined based on pilot and industrial data. Our pilot and industrial tests and observations revealed that HPGR should be arranged in closed circuit because of the edge effect, as a negative factor of non-uniform distribution of pressure force along the roller width and presence of non-crushed particles in the mill product. Wet vibratory screen could be the optimum option for screening of its discharge. Fine part of the wet screen discharge could be delivered to the concentration stage without over-grinding in ball mill using a hydrocyclone working in a reverse closed circuit mode. Moreover, our pilot and industrial tests during design and operation of ten HPGRs in various iron ore processing plants proved that higher pressure and lower roller speed in a fixed level of material inside the hopper could give the desired product size distribution.

Jan 1, 2016

By G. J. Kipouros, W. Judge

"The prevalent metal extraction processes for most reactive metals are fused salt electrolysis and metallothermic reduction. The feed material for both of these processes is the anhydrous chloride of the metal under consideration. Dehydration of the feed material is then a critical step in the production of most reactive metals and requires rigorous thermodynamic analysis. Thermodynamic data for most of the reactive metal chloride hydrates have not been measured. Improper dehydration of the metal chloride may lead to a prohibitive amount of hydroxychloride, oxychloride, and oxide. To prevent hydrolysis a certain pressure of hydrogen chloride is required. An estimation and prediction model is presented for the vapour pressures of reactive metal chloride hydrates in an attempt to deduce the conditions necessary for dehydration to proceed without hydrolysis. Thermodynamic data including heat capacities, standard entropies, and standard enthalpies are estimated/predicted for all conceivable intermediate hydrate compounds. Estimations are based on published data as well as trends proven in similar systems. The thermodynamic estimations and predictions are presented for the magnesium, neodymium, praseodymium, and dysprosium chloride hydrates. INTRODUCTIONThe high reactivity of metals such as the alkalis, alkaline earths, and lanthanides prevents their reduction by traditional pyro- or hydrometallurgy. In their elemental form, these metals are raw materials in the manufacture of intermediate products such as alloys and electronic components. Currently the only two viable metal production methods are fused salt electrolysis and metallothermic reduction. Various feed materials have been proposed for these processes. Using the chloride of the metal as a feed material offers advantages in separation and purity of the final product, as well as lower energy input. Chlorides, however, are hygroscopic and must be dehydrated before use. Improper dehydration will lead to a prohibitive amount of oxychloride which will lower efficiencies and contaminate the final product.Optimum conditions for proper dehydration of MgCl2•6H2O to produce pure MgCl2 without hydrolysis have been calculated from existent thermodynamic data and have been reported previously (Kipouros, 1987; 2001). Calculations were also performed for the case of production of pure anhydrous NdCl3 from NdCl3•6H2O (Roy, 1997)] and the mechanism of dehydration was elucidated. Some thermodynamic studies on the dehydration of chlorides of the rare earths have also been conducted (Sundstrom, 1997; Hong, 1997; Aschcroft, 1968; Haeseler, 1965; Ukraintseya, 1989)."

Jan 1, 2012

By R. Glenn Madill

Western Canada is defined, for the purposes of this paper, as that part of the Dominion bounded approximately by the 95th and 141st meridians of longitude and the 49th and 80th parallels of latitude. It is comprised of Manitoba, Saskatchewan, Alberta, British Columbia, Yukon, and that portion of the Northwest Territories lying to the west of the 95th. meridian. The first magnetic observations made in Western Canada were in the interests of navigation by sea. Observations were made by Captain Middleton in Hudson bay at Churchill and York Factory in 1725, and along the Pacific coast by Captain Cook in 1778 and Captain Vancouver in 1792. The first systematic magnetic survey in Western Canada was made between 1819 and 1826 by Sir John Franklin in his widely distributed explorations. It is of interest to find that while the first magnetic declination observations made in Hudson bay and along the Pacific coast were purely in the interests of navigation, the next investigations, which were made in the Western Arctic, included measurements of inclination and force with those of declination. There was a valid reason for this more complete research into the magnetic field as the construction of declination charts depended on the position of the north magnetic pole. Halley promulgated a theory 1683 that " the globe of the Earth may be regarded as one great magnet, having four magnetic poles, two of them near each pole of the equator, and that in those parts of the world which lie near any of those magnetic poles the needle is chiefly governed thereby, the nearest pole being always predominate over the more remote" . The position of a magnetic pole may be defined as a point where the inclination is 90 degrees and the horizontal force zero. It is obvious that the position cannot be' defined by declination observations alone since, for some distance from the magnetic pole, .the horizontal force is too weak to give directive force sufficient to effect the pointing of a compass.

Jan 1, 1948

By J. Zinck

The management of mine wastes generated by both active and inactive mining is an ever more challenging issue. The cost to manage and treat mine wastes, including tailings, waste rock, treatment sludge and slag, is estimated at over $50B in Canada and the United States alone. Cost-effective technologies are required to meet both short and long term challenges and increasing environmental standards. This paper will provide an overview of novel and conventional technologies to manage mine waste particularly in the areas of waste stabilization, treatment and disposal technologies.

Jan 1, 2004

By Andrea McGlynn

Iron Ore Company of Canada, Labrador City 2011?Canada's largest iron ore producer, leading global supplier of iron ore pellets and concentrates ?Rio Tinto (58.7%), Mitsubishi Corporation (26.2%), Labrador Iron Ore Royalty Income Fund (15.1%)

May 1, 2011

By d&apos, F. Elia

Hot cracking of magnesium (Mg) alloys during welding creates a barrier to enhancing the use of these alloys in automotive applications. As a result, it is imperative to understand the mechanisms responsible for hot cracking of Mg alloy welds in order to develop means of eliminating this problem. In this study, the hot cracking susceptibility of AZ91E and AE42 magnesium alloys were assessed using the moving torch Varestraint test method. Plates of 3 mm thickness were extracted from AZ91E and AE42 ingots and subsequently tested. Quantitative cracking data in terms of maximum crack length (MCL) was used for evaluating the cracking susceptibility. Scanning electron microscopy was carried out. The results suggest that AE42 showed a higher resistance to hot cracking in comparison to the AZ91E alloy. This was attributed to the difference in microstructure between the two alloys. In the fusion zone and HAZ of AE42, the brittle needle-like A1IIRE3 phase was seen to decompose to the more ductile particle-like Al2RE phase, thereby increasing the alloy's resistance to hot cracking. In contrast, SEM fractography revealed that brittle A16Mn and Mg17A112 intermetallic particles segregated to grain boundaries and triggered hot cracking in AZ91E.

Jan 1, 2011

By T. Abu Leil

A new class of ternary Mg-Sn-Ca alloys is being developed to address the dual demands of corrosion and creep resistance at service temperatures. While tin has proven to enhance the corrosion resistance, calcium is expected to significantly increase their creep resistance of binary magnesium alloys. Their effects in ternary magnesium alloys are not yet known. The series of alloys studied has Sn and Ca in the ranges 3-6% and 1¬2%, respectively. The results indicate that these alloys have two-phase structures with CaMgSn phase dispersed in a matrix that is predominantly a solid solution of magnesium. The corrosion behavior of these alloys has been investigated by means of salt spray tests and potentio-dynamic measurements. Creep behavior of these alloys was measured at a temperature of 135 C under an applied compressive stress of 85 MPa. Scanning Electron Microscopy with Energy Dispersive X-ray facility and X-ray Diffraction techniques were used to characterize the microstructures. The results indicate the prospect of designing alloys that can provide optimum combinations of corrosion and creep resistance by adjusting the relative compositions of Sn and Ca in the system.

Jan 1, 2006

By L. Salnais

"Aluminum alloy structural components f or aircraft designed prior to the early 1970s, were machined from 2024, 7075 and 7079 plate, bar and forgings in either the T3xxx of the T6xxx tempers. Protective treatments for these parts consisted of chromic acid anodizing and alkyd zinc chromate primer, plus a nitrocellulose lacquer for exterior parts.The major service problem with these parts was the frequent occurrence of exfoliation corrosion and stress corrosion cracking (S. C. C.). Therefore, 2024 and 7079 alloys, with min or exceptions, were not used in aircraft designed after the early 1970s. Replacement materials were 7075 and 7050 alloys in the overaged, exfoliation corrosion and S. C. C. resistant, T73xxx tempers.The use of improved materials together with the upgrading to chromated epoxy primers, polyurethane enamels and the introduction of water displacing corrosion inhibiting compounds have significantly reduced corrosion in aircraft. IntroductionThe prevention of corrosion in aircraft has been a challenge to aircraft designers for many decades. With the design of the first all-metal aircraft, the designer and builder were thrust into the relatively new field of protective treatments as corrosion started to become more prevalent. This resulted from the continually increasing importance and wider utilization of aircraft, and their exposure to a wider variety of ho stile environments such as urban industrial pollution, high humidity tropical areas and salt ladened marine environments.Corrosion advanced another significant step when, after World War II, designs of new and larger aircraft utilized larger and thicker metal sections in the manufacture of structural components. With thicker mill products came higher residual heat treat, fabrication and assembly stresses resulting in an increased number of stress corrosion and exfoliation corrosion problems.Apart from the exterior environment, aircraft interior s can be exposed to a number of fluids which are either directly or indirectly responsible for corrosion. The most common of the fluids is water which is usually introduced as a result of condensation, especially in pressurized fuselages, and spillage from lavatories, galley s and electrolytes from batteries. These fluid s have a degrading effect on protective treatments and are also corrosive to the substrate metal. Fluids such as phosphate ester hydraulic fluids and ester based turbine engine lubricating oil s are not corrosive to the substrate metal, albeit they do contribute to corrosion by the degrading effect on protective treatments."

Jan 1, 1988

By T. Krumins, F. C. Ruff, M. Eichhorn, L. Zunti

Hatch Ltd. has recently completed a project to increase refractory gold ore processing capacity at Newmont Mining Corporation’s Twin Creeks facility. The objective of the project was to increase throughput by approximately 10% by adding a third autoclave feed pump to each of the two autoclave circuits. To minimize project capital cost, autoclave feed pumps from Newmont’s decommissioned Lone Tree facility were evaluated and found to be suitable for this new service. The existing pressure oxidation circuit was reviewed in a debottlenecking study to determine other upgrades required to facilitate the increased throughput. Interruption to operations was minimized with a detailed construction plan, supplemented with detailed 3D layout model sequencing studies. The focus of this paper is project development, multi-discipline design considerations, and implementation results.

Jan 1, 2014

By M. Massinaei, M. R. Yarahmadi, S. Zeidabadi, M. Oliazadeh

"Although the majority of new flotation column installations continue to be for cleaning or recleaning, an increasing number of flotation projects are specifying columns for roughing or scavenging duties. NICICO has recently installed flotation columns operating in rougher, cleaner and re-cleaner circuits at three new copper concentrators; Miduk, Sungun and Sarcheshmeh. Miduk is probably one of the unique operations that use flotation columns in a rougher circuit. The Miduk rougher circuit comprises five CISA parallel columns. The rougher concentrate constitutes 88% of final concentrate and reports to concentrate thickener. The rougher tailings are scavenged with ten 50 m3 mechanical cells. The scavenger concentrate is then reground and cleaned in three 3.2 m columns in parallel. The cleaner tailings are scavenged in six 50 m37mechanical cells. The cleaner tailings along with the rougher scavenger constitute final tailings.In Sarcheshmeh, the cleaner concentrate is re-cleaned in a column. The column tailings are sent back to the cleaning circuit and the concentrate is reported to the concentrate thickener.This paper reviews performance details of the flotation columns utilized in rougher circuits at Miduk and compares their metallurgical performances in an industrial scale with columns at cleaning circuits for copper flotation. Practical limitations for applying the flotation columns in rougher circuits will be discussed in details.INTRODUCTIONThe use of flotation columns has grown rapidly since the first successful commercial application at Mines Gaspe, where columns were used in a cleaning circuit to float molybdenite. Early applications of columns were restricted to replacing or adding final cleaning stages in existing circuits. Columns can achieve superior cleaning as compared to conventional cells due to their ability to support a large froth depth and the use of water for washing froth. Wash water travels down through the froth and crosses the pulp/froth interface, replaces the entrained particles reporting to the froth from pulp and improve the concentrate grade."

Jan 1, 2011

By R. Roufail

"Energy consumption in stirred mills has been studied, in the last couple of decades, on a macro scale. Effective operation and meeting particle size required for downstream operations used to be the main objectives behind energy utilization of stirred mills. In this paper, three energy terms are defined to assist in understanding the breakage mechanism for various types of minerals versus mill operation. The types of minerals studied had diverse physical and mechanical properties that are summarized as specific gravity, hardness and crystal structure. The minerals utilized in this study were quartz and galena. The effect of quartz and galena mix has been addressed as well as Lead-Zinc ore sample from SAG mill discharge. The energy input to the mill is function of the agitator speed, therefore three agitator speeds were evaluated, 1000, 1500 and 2000 RPM, respectively. The energy terms studied are specific energy (kWhr/ton). Effective energy is the ratio between net energy and total energy consumed by the mill. Last type of energy is the specific breakage energy, which is the net energy consumed by the mill per one-micron breakage. Results showed that specific energy and specific breakage rate are functions of mineral type, while effective energy is only function of mill input power (agitator speed).INTRODUCTIONGrinding is the largest energy consuming component of a mineral processing operation and typically consumes about 50% of the total energy used at a mining operation (Botin, 2009). Over the last two decades, stirred mills have been extensively utilized in mineral processing operations due to increased mineralogical complexity of ore bodies. Stirred mills grind particles to less than 10 µm by applying a high power intensity. The technology has been the focus of several research studies to investigate mill energy and grinding mechanisms. Becker, et. al. (2001) studied the relationship between different types of energy including input energy, specific energy, volume/mass specific energies, to stress intensity and final product particle size. Other studies such as by Kwade (1999), Kwade and Schwedes (2002), Blecher et al (1996), Partyka and Yan (2007), Stender et al (2004), focused on mill design and/or stress intensity distribution. Peukert (2004) studied the effect of mechanical properties of the grinding media and ground material on the comminution process."

Jan 1, 2016

By Jamie Archibald

The Department of Mining Engineering at Queen?s University conducted a study of backfill practices in underground mines across Canada to assess the current state of backfill usage and to overview potential hazards associated with backfill practice, from preparation to transportation to placement. The primary aim of this study was to cover each component of a typical mine backfill system, and to identify potential incidents leading to the disruption of backfilling operations and any associated corrective actions. This paper, Part II of the study, deals with underground operations consisting of backfill transportation and backfill placement. Part I of the study, which deals with surface operations consisting of backfill material supply and backfill plant preparation, is also presented in these proceedings. A review of safety measures associated with current backfill operations and recommendations for procedures of best practice that should be implemented to reduce fill-related hazards in all mine backfill workplace environments are presented. In general it has been found that system failures normally lead only to minor losses to the operations.

May 1, 2009