Search Documents

By G. G. Richards, Y. Oyediran, V. Chow

The oxygen softening process for partial removal of arsenic and antimony from lead bullion has been in use at Teck Cominco's Trail smelter since 1986. In this process, industrial oxygen is injected into bullion to remove As and Sb with the formation of an oxide slag. In Trail, the levels of these elements are reduced to concentrations suitable for processing in the Betts electrorefining plant. Recent moves toward the treatment of higher arsenic-bearing feeds have necessitated an increase in the process capacity to meet the specifications for drossing plant bullion. Process intensification trials were conducted in-plant to develop an operating strategy for higher bullion processing rates. This was preceded by a study conducted with McGill University to develop a fundamental understanding of the therm ochemistry and kinetics of the process. The results have yielded more effective control of the operation, and identified opportunities for further improvements.

Jan 1, 2008

By J. C. Hampton, L. A. Matzar, C. R. Gamwell

In geomechanics, conducting uniaxial or triaxial compression tests require samples to be prepared to a certain length-to-diameter ratio. This ratio is typically defined as 2:1 (length to diameter) and is accepted as a common standard for all materials on which mechanical properties testing is performed. Variations in sample length can cause changes in measured strength properties across multiple material types, such as cement, rock, or soil. Within the oil and gas industry, it is not uncommon to receive samples for technical services work that are slightly under or exactly the length requirement before surface grinding and sample preparation. Many of these samples are discarded from uniaxial and triaxial compression tests and used in another manner; therefore, it is necessary to study the length-to-diameter ratio in efforts to understand the limits and validity of testing samples that are slightly out of the 2:1 ratio. This paper discusses uniaxial compression tests performed using Berea sandstone and a standard cement mixture of 2.54-cm diameter to study changes in rock strength and properties. Compressive strength for each lengthto- diameter ratio over a range of 0.5:1 to 2.2:1 was measured. The investigation was extended to study near-end effects, where the sample length is near, but not exactly twice the diameter. It was discovered that the cement samples conformed reasonably well to the suggested ASTM correction factors. The sandstone did not conform to the correction factors and further analysis is required to develop a correction factor unique to the material. Near end effects, in both the cement and Berea, were found to increase compressive strengths, especially when the L/D of the samples was increased slightly over a 2:1 L/D.

Jan 1, 2015

By Bahjat Khoshaba, Bern Klein, Haixing Yan, Libin Tong, Andrew Bamber

"When a conductive or magnetic particle was put into an electromagnetic field introduced by an electromagnetic sensor, the particle can influence the electromagnetic field which can be used to characterize this particle. The electromagnetic technology based on eddy current theory was explored to investigate its potential in both the separation of minerals and the pre-concentration of a base metal ore. Samples tested in the study included the minerals obtained from Ward’s Science and the low grade copper ore particles obtained from Mount Polley Mine. The effects of mineral type, sensor frequency, particle size, particle position on the sensor surface, and particle lift-off on the magnitude and phase of the electromagnetic spectra were investigated. The electromagnetic spectra of various minerals show that it is possible to separate chalcopyrite or magnetite from tested minerals, simply based on the magnitude of the spectra. The spectra of the ore particles were determined by the mineral in the particles with the strongest signal. The effect of the pre-concentration of the low grade copper ore is determined by the association of chalcopyrite with magnetite. Direct sorting is the mechanism in the separation of mineral particles, while indirect sorting is the mechanism for low grade ores.INTRODUCTIONSensor-based sorting technologies include radiometric, X-ray transmission, X-ray fluorescence, near infrared, photometric, inductive, microwave heating and so on. Sorting not only discards barren rocks away from the concentrator but also recovers metal bearing that would be lose to the waste dump. The benefits of pre-concentration using sensor-based sorting are achieved on reduced energy consumption for comminution and reduced water usage on a volume per weight of metal basis (Bamber, 2008; Gunson, Klein, Veiga, & Dunbar, 2012; Kleine & Wotruba, 2010; Knapp, Neubert, Schropp, & Wotruba, 2014; Kobzev, 2014; Lessard, de Bakker, & McHugh, 2014; Mazhary & Klein, 2015; Robben, Wotruba, Robben, von Ketelhodt, & Kowalzcyk, 2013). Amongst others, high frequency electromagnetic sensors were developed for ore sorting at MineSense Technologies Ltd. and are subject of this paper. Improving the understanding of ore heterogeneity is the basis for developing a successful semi-bulk or bulk sorting systems by incorporating the sensors in the material handling equipment (MineSense Technologies Ltd., 2016). The present study focuses on the bulk sorting potential and bulk sorting mechanisms of the electromagnetic technology in the pre-concentration of minerals or ores."

Jan 1, 2016

By V. S. Melamud, A. G. Bulaev

"Sulfide ore processing is characterized by significant losses of metals, for example, with flotation tailings. Therefore, flotation tailings can present an important source of metals. The treatment of flotation tailings is a technological issue due to low content of valuable metals (e.g. copper and zinc) and high iron content. The goal of the present work was to investigate extraction of base metals and gold from old flotation tailings containing 17% iron, 0.26% copper, 0.22% zinc, and 0.7 g/t gold. Chemical leaching in columns with 0.5 to 10% sulfuric acid solutions and bioleaching in air-lift percolators were used for the extraction of base metals. 1% H2SO4 provided high extraction of base metals and best selectivity. Recovery of copper and zinc reached 35% and 40%. Increasing H2SO4 concentration did not lead to significant increase in base metals extraction, but led to increased iron concentration in the pregnant solutions. The 1% H2SO4 leaching solid residues were used for further experiments. Acid leaching and bioleaching did not result in significant increase in base metals recovery. Leaching of the residue with 10% H2SO4 provided extraction of 4% copper and 20% zinc, and bioleaching for 100 days provided extraction of 16% copper and 12% zinc. The recovery of gold by cyanidation from the flotation tailings, the 1% H2SO4 leaching solid residue and residue of two-step acid leaching were 50, 49, and 65%, respectively. The results suggest that acid leaching can be effective approach for treatment of old flotation tailings.INTRODUCTIONAbout 80% of base metals (copper, nickel, zinc) are produced through pyrometallurgical treatment of sulfide ores. Mining and metallurgical treatments of sulfide ores are presently characterized by significant losses of non-ferrous and precious metals into the various wastes. For example, flotation of sulfidic ores yields formation sulfide flotation tailings. These wastes pose a problem not just because of their sheer volume, but some of them may affect local ecosystems. Nowadays, mining and metallurgical wastes can be considered as technogenical source of base metals."

Jan 1, 2016

By Emilio Giuseppe Sarno Severi

Mining and Petroleum Similar Industries ?Asset Intensive ?Exposed to market volatility ?Highly Risky Operations ?Scarcity of Experienced and Trained resources ?Operating in diverse countries with different cultures ?Increasing Environmental and Safety Regulations

Nov 1, 2011

By R. A. S Villegas

The Brazilian government announced in 2007 its plans to reactivate the nuclear program. As a result of this decision, a new nuclear power plant is already being built and there are studies dealing with, among other activities, the building of 4 to 8 new ones until the end of 2030. Such increase on the country?s uranium demand affects INB, the Brazilian state company that?s in charge of uranium supply. This paper describes scenarios predicted to the Brazilian nuclear industry for the next years and the INB plans to meet the country?s needs in terms of uranium exploration and production.

Aug 1, 2010

By A. C. Hatton

Doped SrCoO3.8 was found to be a promising material for use as a cathode component in intermediate temperature SOFCs. In this work, strontium cobaltite ceramics doped with 10 mol% to 90 mol% samarium were synthesized using the glycine nitrate process in order to study the electrical conductivity and thermal expansion at temperatures of up to 800°C. As-synthesized powders were deagglomerated, pressed and sintered at temperatures ranging from 1100-1250°C. The effect of temperature and composition on electrical conductivity and thermal expansion are presented and discussed.

Jan 1, 2005

PROFIL D'ENTREPRISE Léandre Gervais & Associé(e)s est une société d'experts-conseils en ingénierie de la structure, de la mécanique & de la tuyauterie, et de l'électricité et de l'instrumentation. Nous offrons des services hautement spécialisés à notre clientèle des secteurs industriels des mines et de la métallurgie, au Québec, au Canada ainsi que dans plusieurs autres pays du monde. Notre mission est d'assurer à nos clients un ensemble de services d'ingénierie de haute qualité contribuant à la mise en oeuvre et à la réalisation de leurs projets d'affaires. Léandre Gervais & Associé(e)s emploie 36 employés à temps pleins et opère à partir de Val-d'Or, province de Québec. SERVICES OFFERTS Nous avons réalisé de multiples mandats pour notre clientèle de différent pays du monde dans les domaines d'expertise les plus variés : ?Études de faisabilité ; ?Ingénierie conceptuelle ; ?Ingénierie de détail ; ?Gestion de projets ; ?Ré-ingénierie de la maintenance.

May 1, 2001

By M. J. Nicol, C. van Wensveen

The kinetics of the oxidation of thiosulfate by copper(I I) in ammoniacal solutions have been studied in the presence and absence of dissolved oxygen. The formation of an intermediate mixed ammine/thiosulfate copper(II) complex ion has been confirmed and the rate of the reaction monitored by simultaneous on-line spectrophotometric, dissolved oxygen and potentiometric measurements. The rate of the anaerobic oxidation of thiosulfate by copper(II) was found to be orders of magnitude slower than that in the presence of dissolved oxygen and is inhibited in the presence of ammonia and anions such as sulfate and chloride as a result of competition with thiosulfate for the axial coordination sites on the copper(II) tetrammine complex. In the presence of dissolved oxygen, it was found that the copper(I) thiosulfate complexes are only very slowly oxidized while the copper(I) diammine complex is rapidly reoxidised to the copper(II) state. Thus, the initial rapid reaction with copper(II) leads to a pseudo steady-state condition in which the concentration of copper(I) is relatively constant and the rate of oxidation of thiosulfate can be predicted from the measured rate of oxidation of copper(I) by oxygen in ammoniacal solutions. The effects of the concentrations of ammonia and thiosulfate on the oxidation rate can be rationalized on the basis of the above coupled to the species distribution of copper(I) in the ammonia/thiosulfate system. It is shown that, with relatively simple measurements of dissolved oxygen and copper concentrations, the rate of oxidation of thiosulfate can be predicted under typical leaching conditions.

Jan 1, 2005

By W. J. Jenner

"Introduction The Saskatchewan Power Corporation is a provincial crown corporation which operates under a mandate to supply all customers within Saskatchewan with electricity and natural gas. The Saskatchewan Power Corporation operates two coal mines within the province of Saskatchewan. The Souris Valley Mine is located a few miles south of the city of Estevan and produces approximately 300 000 Mg of lignite per year. The lignite is shipped about four kilometres by truck and burned at the 882 MW Boundary Dam Power Station, also owned by the Saskatchewan Power Corporation. The Poplar River Mine is located just south-west of the town of Coronach, Saskatchewan which is some 190 kilo metres west of Estevan. This mine produces approximately 1 675 000 Mg of lignite per year. The lignite is shipped seven miles by rail to the Saskatchewan Power Corporation's Poplar River Power Station. The Poplar River Mine is the sole sup plier of fuel to the Poplar River Power Station, which generates some 300 MW of electrical power. A second 300 MW unit is due to be commissioned at the Poplar River Power Station in mid-1983 and the Poplar River Mine will have doubled its capacity to approximately 3 350 000 Mg per year by that time: Souris Valley Mine Geology The Souris Valley Mine extracts lignite from the Estevan seam of the Ravenscrag Formation. This formation is of Tertiary age and was deposited during the Paleocene Epoch. The Ravenscrag Formation outcrops throughout southern Saskatachewan and all coal mined in the province occurs in this formation. Ravenscrag sediments are deltaic in origin and are composed of a series of fine sands, silts, clay and lignite deposits."

Jan 1, 1985

By Frederik H. Kriel, John Ralston, Craig Priest

"Stream-based microfluidic solvent extraction offers a novel alternative to bulk-scale mixer-settler operations. However present maximum throughputs are restrictive and there are engineering challenges that need to be overcome before the technology is robust. This is especially the case for mineral processing, where circuits must be able to handle variable feed streams with long retention times and where maintenance should be minimized. This paper highlights research directed at investigating and evaluating these challenges for actual mineral leach solutions of metal ions. Molecular and particulate channel fouling is discussed. Most extraction systems studied to date show no effects that would preclude use of the technology. For rare earth elements (REE) with fast extraction rates, scale-up of volumetric throughput to 100 L/h using suitable arrays of channels, microfluidic chips and modules is shown to be achievable using a small contactor (approx. 2 m3) platform. This requires only 2–3 % of the typical aqueous phase inventory and residence time used in an equivalent mixer-settler. For a circuit with 100 contactors, the overall residence time would be less than 1 h, using an aqueous inventory of 40 L.INTRODUCTIONHydrometallurgy is of pivotal importance in many mineral processing circuits around the world, with liquid-liquid solvent extraction (SX) a key step in the separation of many base metals (e.g. Cu and Ni), radioisotopes, precious metals, and the ‘technology’ metals, such as rare earth elements (REEs) (Ritcey & Ashbrook, 1979). The standard equipment for SX in mineral processing is the mixer-settler, in which liquid dispersions are created, by agitation, to increase the surface-to-bulk ratio and, thus increase the mass transfer rate between the liquid phases. In stream-based microfluidic SX (microSX), these high surface-to-volume ratios are achieved by contacting microscopic streams (Ciceri, Perera, & Stevens, 2014), rather than forming small droplets, so that phase disengagement can be accelerated (essentially instantaneous via branching of the two streams of liquid at a channel junction). MicroSX is profoundly different from bulk mixer-settler SX operations and offers exciting opportunities for processing hydrometallurgy solutions (Kriel, Holzner, Grant, Ash, Woollam, Ralston, & Priest, 2015; Priest, Zhou, Klink, Sedev, & Ralston, 2012). Nonetheless, the advantages of using microfluidic environments are presently balanced by very significant challenges relating to throughput, process control, coupling of stages, flow stability, and fouling. If these challenges can be met using smart chip designs, process control and clever engineering, high-value/low-volume SX processes stand to benefit greatly."

Jan 1, 2016

By M. A. Tomlinson, A. Di Feo, T. C. Cheng

"Goldcorp is evaluating the potential for economic reprocessing of historic tailings at several sites, including the Aunor A facility located in Timmins. The overall project is investigating the ability to recover value, remove sulphide minerals and alternative tailings re-deposition strategies. Desulphurization of tailings will eliminate potential acid generation while improved tailings re-deposition could reduce long-term liabilities and closure costs. Through a task-share project between CanmetMINING and Goldcorp, tailings obtained from Aunor A site have been characterized using mineral association analysis and diagnostic separation techniques. The selected tailing samples contain about 2 g/t of gold. Mineralogical analysis has identified coarse agglomerates bound with gypsum and significant free gold, confirmed by high recoveries in cyanide leach tests. However, despite no evidence of surface passivation on the minerals, conventional flotation techniques were found to be ineffective in concentrating gold or sulphides due to the high fines content and highly agglomerated particles.INTRODUCTION Aunor Mine is one of the historic mines that belongs to Porcupine Gold Mines (PGM) in Timmins, Ontario. PGM has undertaken an extensive mine closure program to remediate the legacy and closed mines with the funding supported by operating mines since 2006. Over the course of 100 years of operation in the Porcupine camp, it is estimated (Stevens et al., 2013) that about 130 million tonnes of tailings have been generated. Aunor Mine produced 2.5 million troy ounces of gold between 1940 and 1984, while processing over 7.6 million tons of ore. The original gold grade of Aunor Mine ores was about 10 g/t. With 95% gold recovery at the time, an estimate of 0.5 g/t of gold remains in the Aunor Mine tailings. Aunor Mine has two tailings impoundment areas: designated as Aunor A and Aunor B. The two sites are similar in size, about 7 hectares each. The amount of tailings in the Aunor A site alone is about 3.2 million tonnes. In 2017, bulk tailings were sampled from five designated locations in Aunor A. They were characterized using mineral association analysis and diagnostic separation techniques. The bulk tailings samples contained about 10% total sulphur, 10% iron, 2% arsenic and 2 g/t of gold. The prime objective of this collaborative work between CanmetMINING and Goldcorp is to facilitate the timely development and deployment of innovative tailings reprocessing solutions, specifically in the areas of desulphurization, and recovery of metals. This work targeted specific tailings of interest to Goldcorp which goals are to improve its environmental footprint and to reduce long-term liability. Thus, it is imperative to look for innovative reprocessing options that can overcome not only technological challenges but also achieve economic benefits to offset the costs associated with reprocessing the tailings. Moreover, the greater goal is to demonstrate and deploy tailings reprocessing solutions to solve one of the industry’s most difficult challenges for a sustainable mining industry in Canada."

Jan 1, 2019

By BARRY BANNATYNE

Ombrotrophic Sphagnum peat bogs have a characteristic signature on both colour injrared film (750 nm to 3,000 nm response) and Daedalus injrared line-scanner images (thermal infrared 3 to 5 microns and 8 to 14 microns response). This remote sensing method was used to survey bogs in southeast Manitoba to delineate targets for surface exploration. Target bogs all have a surface growth of Sphagnum; underlying dead Sphagnum ranges from 1 to 6 m thick. Large Sphagnum reserves exist in the Caribou cluster of bogs, and in /979 a bog first identified by infrared sensing was brought into production.

Jan 1, 1984

By P. J. Mackey, Elsie Kossatz

The small town of Bruce Mines lies a few miles east of Sault Ste. Marie, Ontario on the north shore of Lake Huron. This was the site of the first copper mine. This copper smelter used a reverberatory furnace, based on the Welsh process, and operated in the period of 1849 to 1850, when the plant was destroyed by fire. During the period of 1850 to about 1869, crushed and sorted ore was shipped to England and later to the United States. In 1869, a roastleach plant, based on the Henderson Process, was constructed at Bruce Mines and was operated until about 1872. This short article describes the early development of this historic operation. Although the rich copper ore found in the vicinity of Bruce Mines was known to the Indians, its discovery in or about 184 7 was credited to Mr. Keating, who named the area Bruce in honour of Lord Elgin (James Bruce), Canada's Governor General. In 1848, the property was acquired by the Montreal Mining Company for 40 000 pounds sterling and the company immediately sent a small party to investigate the deposit. The party sank a shaft on a lode within a hundred yards of the lake and also reported two adjacent lodes farther inland, which were left undeveloped until the turn of the century. Initially, the foundation of the headframe and hoist was built above the frost line and when the machinery was set in motion it collapsed. Eventually, the shaft was to reach a depth of 300 feet. By 1849, the property was well established and the small settlement consisted of 77 miners, 65 labourers, 4 boys, 11 tradesmen, including blacksmiths and carpenters, 2 mining captains, 1 engineer, 2 clerks and 1 superintendent. The community, including the workers' families, numbered about 250.

Jan 1, 1999

By Roe-Hoan Yoon

"Industrial flotation columns often suffer from low recoveries and high maintenance requirements because of poorly-designed air spargers. The MicrocelTM bubble generators were developed at Virginia Tech to overcome these problems. In this system, small air bubbles are generated by circulating a portion of the flotation pulp through a set of static in-line mixers. The small bubbles improve flotation kinetics and allow a higher recovery (or capacity) to be achieved. Other advantages of the system include reduced air consumption, plug-free operation and on-line maintenance. This article discusses the advantages of the MicrocelTM bubble generators and presents examples of successful in-plant demonstrations.IntroductionColumn cells are widely accepted in industry for cleaner operations because they are more selective than mechanically-agitated conventional cells. The improved selectivity can be attributed to the use of wash water which minimizes the entrainment of fine gangue particles into the froth product. Columns may also produce higher recoveries if the air sparging system is properly designed and steps are taken to minimize back-mixing. Furthermore, the quiescent conditions afforded by column cells may be beneficial for recovering coarse particles that are readily detached from bubbles under more turbulent conditions. Also, properly-designed columns offer advantages in terms of savings in floor space, reduced operating and capital costs, and simplified circuitry.It is unfortunate, however, that some of the advantages of columns are not fully realized in industrial practice. Some column circuits are unable to achieve their design capacity, while others require extensive maintenance programs. These shortcomings can usually be attributed to deficiencies associated with the design, scale-up and operation of the air-sparging system. In this article, some of the basic problems associated with commercial air sparging systems are discussed and alternatives are suggested."

Jan 1, 1994

By Luke Meers

Roadway development rates in Australian underground coal mines are failing to keep pace with modern longwall systems and are unlikely to sustain further improvements in longwall productivity into the future unless step change improvements to roadway development equipment and practices are made. Bottlenecks which limit and constrain improved production and impact the safety of operators have been identified through a series of industry surveys, with the manual installation of strata support materials, consumables delivery, coal haulage and monorail installation being highlighted as major areas to improve development performance. This paper looks at research being carried out at the University of Wollongong in designing an integrated system approach for the fully automated handling and installing of development consumables, and the systems required to support these activities. A series of hard automation manipulation devices have been demonstrated in surface trials and the results indicate that rapid roadway development can be achieved.

Aug 1, 2013

By T. Mulpeter, G. Deschênes

Sadiola Gold Mine is an open pit operation located in Mali and owned by Anglogold Ashanti Ltd, Iamgold Corporation and the State of Mali. A conventional cyanidation process (cyanidation/CIP) treats 15,000 tpd (of a mixture of oxide and sulphide ores) at an average grade of 3 g/t Au. In 2002, the increasing tonnage of sulphides caused an increase in production costs and a decrease in gold extraction (from 95% to 70-76%). Because of the short retention time of the leach circuit (18 hours) and the refractory nature of the sulphides, gold leaching kinetics are critical. A laboratory investigation was initiated to evaluate actual plant practice and identify a means of improving the gold leaching rate. The study was conducted on a "soft" sulphide gold sample containing 4.96 g/t Au, 0.4 g/t Ag, 2.5% pyrite, 1.2% arsenopyrite, and 0.2% pyrrhotite with a P80 of 74microns. Pre-leaching significantly influenced the gold leaching rate. A short pre-leach (2 hours) performed at pH 8, a DO of 8 ppm, and with 300 g/t lead nitrate added at the start or the end, produced the preferred conditions. Pre-leaching for more than 2 hours was detrimental to gold extraction. The cyanide concentration had to be maintained at 450 ppm NaCN to reach a maximum gold extraction within the retention time of the circuit. A maximum extraction of 81.3% Au was obtained in 20 hours (leach residue at 0.97 g/t Au). A high level of dissolved oxygen in the pre-leach was not of any benefit. Extension of gold leaching beyond 20 hours indicated that all leachable gold had been extracted by that time. Plant modifications were made to allow leaching of oxides and sulphides in separate circuits. Treatment of oxide ores is now performed at a higher rate. Sulphides are processed at a lower throughput, with 300 g/t lead nitrate, to allow a retention time of 22 hours. Combined throughput remains the same, and total gold recovery has increased from 76% to 80% for an additional gold production of 16,000 ounces per year.

Jan 1, 2005

By K. Meyer

"The largest cost centres of the David Bell Mine concentrator are grinding, leaching and effluent treatment. Optimizing results during the 6th year of operation are listed below: o SAG mill slurry density control and operating strategies improved liner life and media consumption by 10 and 25%, respectively.o Poly-met liners clad the SAG mill except for the feed end. Lower noise levels and reduced mill downtime have resulted in an improved and more efficient workplace (time required for liner changes is 2 to 3%).o A comparative grinding media study using seven different marked media at the same time showed media wear rates range 120 to 198 mg/kWh and ball mill charge replacement frequencies of 8.3 to 13.1 per year, and that a meaningful wear test must include all media to be tested at the same time in the same mill. High quality carbon steel cylinders had the best economics.o Pre-aeration, using pure gaseous oxygen is accomplished in pipe reactors. Small bubble generators provide oxygen in the first three leach tanks. 1500 to 3000 kg of oxygen is consumed per day. Leach kinetics have improved and trends indicate increases in gold recovery of three to seven ounces per day at reduced costs. Effects of reduced cyanidation of accessory metals on the effluent treatment plant will be discussed in a separate paper."

Jan 1, 1991

By M. Rafieazad, P. Fathi, M. Mohammadi, A. M. Nasiri

This study examines the impact of low-temperature heat-treatment cycles on microstructure and corrosion performance of Direct Metal Laser Sintered (DMLS) AlSi10Mg_200C alloy. It is known that the morphology and the size of eutectic silicon are the two most critical factors affecting mechanical properties of the AlSi10Mg alloy. Although high-temperature heat-treatment cycles are common practice for the strengthening of the cast Al-Si-Mg alloys, in the case of DMLS fabricated AlSi10Mg alloy, high-temperature solutionizing and low temperature annealing cycles result in mechanical properties degradation primarily due to a dramatic decrease in the solubility of Si in the super-saturated a-Al matrix of the as-printed alloy. In this study, low-temperature heat-treatment cycles that only promote precipitation of Mg2Si accompanied by the interruption of the silicon network were investigated. SEM and XRD analysis were utilized to observe the evolution of microstructure after different annealing heat-treatments at 200, 250, 300, and 350°C for 3 h. Increasing the heat-treatment temperature contributed to the Si networks interruption and an increased precipitation of Mg2Si phase. Low-temperature annealing from 200 to 350°C was found to promote the homogeneity of the microstructure characterized by a uniform distribution of eutectic Si in ??-Al matrix. Additionally, in order to investigate the impact of different heat-treatment cycles on corrosion resistivity of DMLS-AlSi10Mg_200C, the potentiodynamic polarization testing and electrochemical impedance spectroscopy were performed in a 3.5 wt.% NaCl solution. The results revealed more uniformly distributed pitting attack on the corroded surface by further increase in the annealing temperature, which was attributed to the uniformity of Si dispersion. In comparison, low temperature annealing at 200°C led to a penetrating selective corrosion attack along the melt pool boundaries, resulting in a higher corrosion rate associated with the lower absolute value of impedance of the protective passive film on the surface.

Jan 1, 2018

By G. Ozbayoglu, Z. Ozdemir

Turkey is the main boron minerals producing country in the world. The most important boron minerals are tincal, colemanite and ulexite. All mining, beneficiation and handling operations generate fines which cause ecological and economical problems. Utilization of this accumulated material requires both upgrading and agglomeration. The aim of this research was to exploit the ulexite fines by improving their grade and size. Attrition-scrubbing followed by washing and screening was employed for upgrading the fines. It was found that the grade can be increased from 23-25% B2O3 to 29% B2O3 with 73% recovery. Briquetting was applied as the size enlargement process. During the briquetting, the effect of moisture content, pressure, amount and type of binder, and drying on the quality of briquettes were investigated. The tests showed the possibility of production of strong briquettes by adding water alone, but the briquettes had no resistance to abrasion and water. Binders, namely boric acid and borax have been added to improve the properties of briquettes. The results showed that the compressive strengths and abrasive resistances of briquettes obtained with both binders were acceptable. However, the briquettes have no water resistance properties.

Jan 1, 2004