Search Documents

By H. Ewaschuk

"INTRODUCTIONRio Algom's Stanleigh Mill in Elliot Lake began production in June of 1983. The highly instrumented mill treats uranium ore at an average rate of 3900 metric tons per day. To help ensure a good start-up and low operating costs, an extensive training program was undertaken prior to and during start-up. This presentation describes how an unconventional operating crew were combined to form an operating unit with a high efficiency in terms of production and labour utilization. I would like to point out at the outset that the operating philosophy, and the role of the supervisors and the operators as set up at Stanleigh is not unique. Indeed, I have seen the same results at a couple of small plants where efficiency meant survival. However, these situations appeared to be the exception, and it was not readily apparent how similar results could be obtained in a larger plant. A factor that existed at the time was low labour turnover. As in most parts of Canada, jobs were easy to get in the Elliot Lake camp in the late 1970's. This, and other factors, contributed to an unusually high labour turnover. This changed dramatically in the early 1980's. Indeed, Rio's two other operating mills, Quirke and Panel reduced crew sizes at this time to reduce operating costs. As a result all of Stanleigh's operators came from Quirke and Panel with experience varying from 4 to 7 years. The experience that operators had was obviously of benefit and served to reduce the scope of the training program from what would have been required with inexperienced personnel."

Jan 1, 1985

By R. G. Zaripova, N. D. Ryan, H. J. McQueen

The austenitic and ferritic stainless steels do not undergo any phase transformation that induces very fine grains in the product through thermomechanical processing as practiced in most other steels. Considerable grain refinement can be achieved by intense multistage deformation descending through warm to cold working; notably multi-axial forging of bulk material can attain high strains with diminished risk of cracking. Hot working to improve ductility yields finer grain sizes as the T is reduced and strain rate E raised; increased strain has limited effect due to the steady state regime. Ferritic steels develop subgrains with size diminishing as E rises and T falls with the advantage of retained strain hardening; recrystallization delivers grains several times the cell size. In austenitic steels, dynamic recrystallization (DRX) provides finer grains at higher E and lower T with a lower limit due to intergranular cracking. The DRX grains contain a strengthening substructure that can easily be retained by quenching; if static recrystallization is allowed to occur the grain size rises markedly. Multistage rolling with diminishing T is able to provide grain refinement to the same degree as straining at the finishing T yet provides better ductility. grains on recrystallization. As a result of the strain induced transformation to martensite, small subzero deformations of austenitic or duplex steels produce very high dislocation densities that yield marked grain refinement when they revert upon reheating.

Jan 1, 2004

By Franc R. Joubin, Donald H. James

"The Property of Rix Athabasca Uranium Mines Limited is in the Beaverlodge area of northwestern Saskatchewan. The mine is 7 miles by road north from the Lake Athabasca port of Bushell which is 250 miles north by aircraft or boat from railhead at Waterways, Alberta.The Rix property is a portion of the former DD 1 concession, obtained in 1949 from the government of Saskatchewan when private prospecting for uranium became permissible. The concession was prospected in detail during the 1950 and 1951 field seasons and a great many radioactive show-ings were discovered. Development and drilling were concentrated in two and later three of these areas, and by late 1952 enough ore had been indicated in the Leonard series and ""Smitty"" zone to justify underground development by adit-drift and shaft respectively.Four hundred feet of drift development on the Leonard No. 1 vein and the sinking of a two-level vertical shaft with related lateral development on the Smitty zone were completed in 1953. In April 1954 the Smitty section was placed in production at a rate averaging 100 tons per day, thereupon becoming the first privately owned post-war uranium producer in Canada. The ore is shipped for processing 12 miles by truck to the mill of Eldorado Mining and Refining Limited.Until recently all of the Company's production was drawn from the Smitty orebody. In April, 1955, ore production commenced from the faulted west extension of the Smitty structure, known as the Rix 62 zone, and from the Leonard No. 1 vein.The Smitty orebody (see Figure 2) is an intensely brecciated lenticular zone bordering both sides of the Smitty fault. The breccia areas are irregularly mineralized with pitchblende, very sparse galena, and pyrite in a gangue of feldspar, chlorite, calcite, and silica, all thoroughly soaked with fine-grained hematite to produce the locally-called ""red alteration"".Tenor of the ore currently being mined is classified information. The average grade estimated, prior to production, was 0.20 per cent (4.0 lbs.) U308 per ton."

Jan 1, 1949

By E. F. Evoy

"The Gunnar uranium deposit was within metasedimentary rocks of the late Archaen Tazin Group. These rocks were intensely altered by albitization so that the immediate host to the ore consisted dominantly of albite, and by the subsequent introduction of calcite. The ore consisted of disseminated pitchblende and uranophane in a pipe-shaped breccia zone. Oxidation of the ore was more intense near surface than at depth, but there was no near-surface enrichment.IntroductionThe Gunnar Mine site is on the tip of Crackingstone Peninsula, on the north shore of Lake Athabasca, Province of Saskatchewan, Canada. The peninsula forms the southern part of the Beaverlodge mining area. The ore consisted of disseminated pitchblende and uranophane in brecciated metasedimentary rocks of the Tazin Group, and the deposit was characterized by extreme albitization and subsequent carbonatization of the host environment.Production from the mine began in 1954 and the ore was depleted by 1963. In that interval the deposit yielded about 5 million tonnes of ore containing about I. 75 kg/tonne U3O8. It was mined initially from an open-pit and subsequently from underground; the open-pit contributed about 55% of total tonnage. Uranium was recovered by atmospheric leaching in sulphuric acid, ion exchange concentration, and precipitation with magnesia.This paper is based on studies made during the productive life of the mine and is concerned primarily with pre-ore alteration of the rocks containing the deposit, and with the ore mineralogy."

Jan 1, 1986

By T. E. Newkirk

In the past few years there has been considerable controversy on the most suitable material to be used in ventilation doors which will have to serve also as fire doors. For this reason it was thought useful at Mclntyre to find out to what extent our zinc chloride treated spruce doors were fire resistant and what protection we could expect in case of an underground fire. The doors to be tested were constructed of the same material as that used in our regular ventilation doors underground, namely, 2-inch tongue-and-groove well seasoned spuce. It is to be noted, however, that whereas the dimensions of the ventilation doors are 5 ft. by 6 ft., those of the test doors were only 14 in. by 17½ in. The treated doors were made up from lumber that l1ad been treated with chromated zinc chloride, as described in Mr. Keeley's paper. Two kinds of tests were carried out: a heat test and a flame test. An electric muffle furnace for assaying, equipped with a pyrometer, was used for the beat test, the furnace door being replaced by the wooden door to be tested. In the flame test, the door to be tested formed one end of a rectangular steel box in which was placed a large blow-torch. Air was admitted at the rear of the box. A pyrometer recorded the temperature at the inside surface of the door where flame impinged. The results of the tests are presented in the accompanying table, in which the word 'failed' is to be interpreted as meaning that the door had been damaged to the extent that smoke, but not necessarily flame, issued from its outside surface.

Jan 1, 1949

By Paul Staples, Paul Messenger, Greg Lane

"Every project is different. While “conventional” SAG and ball mill circuits will suit many projects, for others there are alternatives, which may produce improved outcomes. This paper examines particular examples of recent front end designs which either went against conventional thinking or which employed “out of the box” thinking to realize the desired results.One such example is the design strategy employed for a small capacity gold plant in Victoria, Australia. The selection of HPGR technology for small capacity projects is not generally favoured, given the relatively high cost of small HPGR machines. However, the unusual size distribution of the gold and its liberation characteristics were expected to lead to improved gold recovery offsetting the higher capital cost.Another example is the first large scale application of milling in acid for copper recovery, at a project in south east Asia. The stainless steel, single stage SAG mill using ceramic grinding media was more expensive than a mill constructed of conventional materials. However, the steps of scrubbing, slurrying, grinding and leaching could all be achieved in a single unit operation and the need for thickening and repulping with acid after milling was eliminated.Rod mills were selected for both primary and secondary milling duties for another south east Asian project despite their somewhat outdated reputation. A review of previous industry experience confirmed that rod mills could outperform conventional rod/ball or SAG/ball circuits in cases where the size distribution of the ground product is critical to downstream recovery.These examples are discussed with particular focus on the key drivers in each case."

Jan 1, 2008

By Cale J. Dubois

At Cameco Corporations' Cigar Lake Project, large excavations are developed on the 480 Level and 500 Level must remain stable for at least 15 years to host underground processing infrastructure. Following the successful dewatering of the mine in October 2009, subsequent internal rockmechanics investigations augmented by third party technical investigations; determined that to keep the back of the Water Flush Crusher/Run-of-Mine (WFC/ROMs) excavation stable; required a rehabilitation strategy to mitigate deterioration/deformation of the WFC walls and intersection pillars. The mechanism of failure propagating the movement of the excavation walls is understood to be controlled by the presence of a dominant E-W striking and steeply dipping foliation within a relatively weak and mildly altered rockmass sub-parallel in strike with 14 meters high walls and an intersection span approaching 15 meters. The application of open and resourceful communications between site mining engineers, geologists, contract mining staff, construction management experts, corporate mining and civil engineers, and third party technical experts resulted in a multi-faceted short-term ground support strategy consisting of standard bolting and screening, deep-seated modified-strand cable bolts coupled with heavy gauge mesh straps, rockmass reconditioning using low-pressure grout injection, and horizontal cable-lacing for the intersection pillars applied in lifts using a top-down methodology. The intention of the short-term strategy was to stabilize the excavation so that a long-term structural steel support installation - consisting of composite concrete walls, and arch support applied to the side walls and crown of the back - could be constructed safely. This paper summarizes the evolution of the short and long-term ground support strategy and criteria for the WFC/ROMs excavation developed using elements of civil, mining and hydrogeologic design.

Nov 1, 2011

By A. Taylor, M. Blanchette, J. Doucet

"A Z1600 Jameson Cell Test Rig was rented for test work at Vale’s Clarabelle Mill operation. This paper discusses the evolution of renting the unit for test purposes to owning the unit and operating it as a revenue generating process component. The paper focuses on three aspects of the Z1600 project; the initial rental and installation, the test work performed in the cleaning circuit, and the business factors which led to the unit being permanently incorporated into the copper circuit.INTRODUCTION Clarabelle Mill is located in Sudbury Ontario (approximately 350 km north of Toronto) on the southwest rim of the Sudbury basin a meteoric impact crater that is 62 km long and 30 km wide. The result of the meteoric impact was concentrated nickel (Ni), copper (Cu) and platinum group metal (PGM) ore bodies in the outer perimeter of the basin; described in more detail by Hanley (1957). Vale currently has seven operating mines in the Sudbury basin, from which nine distinct ore types are mined. Ores are also received from two QuadraFNX mines. Clarabelle Mill processes all of these ores for the Ontario Operations of Vale. The mill, commissioned in 1971, was originally built as one of four mills operated by then Inco Limited. Between the late 70’s and the early 90’s process changes were made to consolidate the Sudbury Operations milling processes into a single operating mill, Clarabelle Mill. In 1990, the SAG mill was installed resulting in peak mill throughput of 11.9 million short tons per annum (Mstpa), with typical throughputs of ~10 Mstpa. Mill average feed grades were 1.4% Cu and 1.2% Ni. During the resources boom, plans were developed to increase the mill capacity at Clarabelle Mill in stages to a final capacity of 13.5 Mstpa. The project known as the Clarabelle Mill Expansion and Recovery Project (CMERP) included expansion and reconfiguration of the grinding and flotation circuits. The first stage was a planned increase in grinding capacity with the reallocation of existing mills, the existing flotation capacity would be required to treat higher throughput until the new flotation circuit was constructed."

Jan 1, 2012

By K. Thuro, S. Schneider, H. Kasling, P. Ellecosta

"One of the most important methods for material testing is the characterization of the hardness, which is defined as the resistance of a material to the penetration of another one. The methods according to Brinell, Vickers, Rockwell and Knoop are today the most common and standardized tests for metal. As they are developed for predominantly ductile materials like steel, they can’t easily be applied to rocks which react much more brittle under indentation. But just as steel, rock is composed of different minerals and has a specific microstructure. Its mechanical parameters are connected with the particular grains, their cohesion and interlocking, just like steel.The abrasivity of rocks and the accompanied wear of drilling tools today are mainly determined by simple and fast laboratory tests such as the Cerchar abrasivity test or the rubber wheel test. Such laboratory tests are good tribological tests, but there are limits. The Cerchar abrasivity test for example has weaknesses in extreme cases, that mean soft or very hard rock types. This leads to an underestimation of abrasivity, e.g. in poorly lithified sandstones or very hard, fine grained and extremely abrasive rocks. As mentioned, hardness characterizes, depending on the type of deformation, predominantly plastic (metal) or elastic properties (rubber). Rocks are in the range between these two extremes. Since the rock drilling process can be seen as a kind of penetration process on macroscopic and microscopic scales, we picked up the idea to characterize the interaction of rock materials and TBM-disc-cutters with hardness tests. In addition, this supports for a better understanding of the wear process on disc cutters. We used the hardnessdisparity concept after Cardu & Giraudi (2012) because wear can be understood as the interaction between the wear part and the material which causes the wear (tribological system). Several rock-forming minerals and some fine to coarse-grained monomineralic and polymineralic rocks were tested. In contrast to Cardu & Giraudi, we used in the first step of investigations the method after Vickers with loads up to 294.2 N (HV 30), depending on the estimated hardness to get bigger indentations and therefore as well information about the cohesion and interlocking of the minerals/grains. We also tested several associated disc cutters. First results show that with higher loads (HV 5 - 30) and at least 15 indentations, we get a structural hardness in fine-grained rock samples, which allows a good characterization of the elasticity and brittleness. Nevertheless, for the coarse-grained rock samples we need up to 40 indentations for a good characterization. Using this method, a prediction of disc cutter wear is feasible taking into account the hardness of the disc cutter steel. In this paper, we would like to present this approved method in material sciences to derive an additional parameter for the characterization of rock abrasivity and wear."

Jan 1, 2015

By M. C. Pietrobon

"A common problem in assessing the applicability of laboratory flotation data is determining how closely conditions during laboratory testing of the ore matches those that occur in a plant. Typical laboratory based investigations do not consider factors such as water quality, pulp temperature and the pulp chemical environment during both grinding and conditioning on laboratory flotation performance. Disregarding these important factors may seriously compromise the validity of conclusions based solely on laboratory experimental results. Furthermore, considering these factors during the flowsheet design stage in the development of new ore resources may reduce financial risk associated with building a new plant. A methodology is described here which embraces these factors in an attempt to bridge the gap between laboratory and plant. The methodology should be considered a vital first step in all laboratory based experimental programs and has implications for fundamental studies on the flotation behaviour of single minerals. This methodology increases the confidence with which findings of laboratory based studies can be transferred to the plant and highlights the effect of variables which may be accessible to manipulation in the plant.Pulp chemical parameters, such as pulp dissolved oxygen demand, pH, Eh, mineral oxidation and solution composition were manipulated in the laboratory by adjusting the duration of gas purging after grinding, the process water input and pulp temperature. A key finding was that matching of the laboratory pulp chemistry to the plant pulp chemistry was dependent upon oxidation after grinding. In turn, mineral oxidation was dependent upon the pH in grinding, water composition and the duration of oxygen purging after grinding. The methodology closely matched the dissolved oxygen demand and surface chemistry of laboratory and plant pulps."

Jan 1, 2002

By O. A. Bascur, J. Patrick. Kennedy

"The lack of integration of mining and metallurgical information at sufficient detail to act is a problem. Without such data, mine cut-off grade can not be optimized on a per grade basis. It is difficult to determine economics without integration of mine transactions, stockpile inventories, process flows and assays. Actions also require real time information from manufacturing assets, but corrected for gross errors from trucks, shovels, conveyors, faulty sensors, bad instrument calibration. Validation methods must include process models to identify corrupt actionable information. This paper presents new tools that use the model the process to sift through available data, identify and eliminate gross errors, and use statistical data reconciliation to create material balanced, internally consistent values. Uses of models allow data to be unified for useby both monitoring and decision making processes.A Real Time Performance Management (RtPM) uses unifying analysis methods to empower everyone in the organization with unparallel real-time intelligence, enabling them to continuously improve performance.BACKGROUNDExtraction of metals has become a global business; new economic and environmental forcing factors are present today which were unheard a couple of years ago that are causing companies to focus on plant operations. High ROI actions can be achieved internally which will increase mining and metallurgical processing unit efficiency and reducing operating costs if the proper information is provided those in the complex that can act. Large changes are possible with many of these small steps if the barriers for action are removed. The chief impediments are lack of infrastructure including the data, computing tools and essential data and bad information.Increased demands will be placed on the types, quantity and priority of information. Metallurgical complexes are attempting to become better neighbors, increase productivity, improve customer service, and satisfy the regulators and compliance groups -- all with fewer people and less costs."

Jan 1, 2004

By A. Ismail

"The paper takes its material from three peat mining and power project feasibility studies sponsored by CANMET and conducted by Montreal Engineering Company Ltd. in the years 1976 to 1980. The role which peat may play in the Canadian energy prospectus is outlined, estimated and measured fuel peat resources are tabulated, and the economic and technical feasibility of mining peat for power generation is reviewed Recommendations are made for future work, and construction and disbursement schedules are developed for a combined peat mining and power generation project. The relationship between the mining of moss and fuel peat is discussed.IntroductionWhereas moss peat has long been produced in Canada, and exported for horticultural use , the underlying fuel peat has received little attention until fairly recently.In the seventies, however, the deepening oil crisis spurred Canadian interest in Irish, Finnish and Russian experiences in the utilization of fuel peat. Among others, Energy, Mines and Resources Canada had long been alive to the possibilities which indigenous peat offers, and in 1976 the Canada Centre for Mineral and Energy Technology (CANMET encouraged a proposal from Monenco to carry out a preliminary study and submit a report on the "" Assessment of Canadian Peat as an Alternative Fuel for Power Generation"". The report was submitted in April 1977. This was the first of a series of studies, and the authors of this paper were involved in its preparation.The escalating price of oil and the increasing problem of relying on its availability have combined to make alternative fuels more attractive. Peat, like other fuels previously uneconomic because oil was cheap, is now progressively gaining in viability. In addition to these factors, the utilization of peat has the following advantages: improvement in the country's balance of payments, by virtue of burning an indigenous fuel;creation of local employment for the mining of peat; improvement in land utilization;peat is a relatively clean-burning fuel, with low sulphur and ash contents."

Jan 1, 1980

By Frank Ebbutt

In this paper it is proposed to point out certain structural factors that; have an important bearing on gold deposition. The subject will be treated; more or less generally. Although the writer has had access to a great many; of Canada's gold mines he does not wish to take the liberty of discussing; details of any particular mine or mines; the aim will be to discuss controls; that are evident in many places.

Jan 1, 1954

By Buse Florian

This paper presents the specific features of the large-scale production and transportation systems (LSPTS), describing the main notions and characteristics of the LSPTS elements. A methodologically unitary approach of the formulation, formalization and solution of the problems regarding the planning of the LSPTS structure development is offered, based on the system description by the aggregation-decomposition method, as weil as on the complex of interreloted models for the planning optimization. The paper describes the characteristics of the complex of dynamic models for investments, utilized in solving the planning problems of the LSPTS structure development.

Oct 1, 2009

By M. Ye. Shulgina, M. L. Bolotin, S. A. Prokopev, Ye. S. Prokopev

Iron ores concentration at Russia’s operations is carried out using conventional flow sheets. They comprise the two-four stage grinding followed by one-two stage magnetic separation. This results in the maximum recovery of magnetite to concentrate and the tailings generation. The final concentrate is generated only during the last stage of magnetic separation. Technologically, this flow sheet layout is not effective at recovering the liberated magnetite grains during grinding to the resulting concentrate. Advanced models of magnetic separators do not allow for the selective separation of the tailings and the portion of the resulting iron ore concentrate. Magnetic product which is the ore mixture of the liberated magnetite grains, high grade and low grade intergrowths is directed to the next grinding stage. In this case, regrinding of the liberated magnetite occurs. In addition, the performance of hydrocyclones during classification in closed grinding circuits is poor. Their classification efficiency does not provide the material separation in accordance with the size. In this case, simultaneous separation in accordance with the density occurs. The quartz particles with the size of 300 mm have similar velocity and trajectory like the particles of magnetite with the size of 60 mm. As a result, light and coarser intergrowths report to the overflow and free heavy magnetite grains report to underflow and return to regrinding (“the density effect”). This resulted in a significant increase of a mill circulating load, the decrease in the feed throughput and higher power consumption. In this connection, the development of iron ore concentrate stage recovery with the focus on gradual liberation of the intergrowths is getting much attention. Gravity concentration technique, particularly, spiral separation is effective at solving the problem of stage recovery not only the dump waste product but also high grade magnetite concentrates at the early concentration stages. This can be attributed to a significant difference in magnetite (4.9-5.2 g/cm3) and host minerals (quartz 2.7 g/cm3) densities, which is the principal during gravity concentration. The test work on concentration of various products samples from current operations (the mills discharges, concentrates from various stages of wet magnetic separation and cyclones underflows) was carried out. Spiral separators SV-500 and ShV-500 manufactured by Spirit LLC were used for the test work. High grade iron ore concentrate (69.05% Fe) was generated during primary wet magnetic separation concentrate concentration using a spiral separator. During the concentration of mills discharges the content of iron in the resulting concentrates and middlings of wet magnetic separation II stage was 64.5% and 64.6%, respectively. The recovery of iron to the concentrates of spiral separation was 33.6-42.0%. The studies presented demonstrate that by using spiral separation for iron-bearing ores concentration, you can separate magnetite liberated grains at the early concentration stages, decrease their regrinding and circulating loads in grinding circuits. This process is able to improve the overall recovery and economics of iron ores concentration process.

Jan 1, 2016

By Guohong Yin

Oxidized sulfidic tailings contain significant amounts of accumulated acidity in the form of water-soluble secondary sulfate minerals and thus constitute long-term sources of acid drainage at many metal mining sites. As part of site remediation activities, alkaline amendments are often added to the oxidized tailings to increase the pH and immobilize the metals. This study assessed the advantages and limitations of using lime mud, a byproduct of Kraft pulp mills rich in calcium carbonate (> 90 wt. %), as alkaline amendment. The inorganic and organic constituents of lime mud samples were quantified. Leachable impurities were determined by the TCLP method. The performance of lime mud was compared to that of reagent grade quicklime (CaO) and calcite (CaCO3). Tailings treated with lime mud or calcite have strong buffering capacities and remain at neutral pH conditions (pH ~ 6.7) for long times. In contrast, tailings treated with quicklime have a very low buffering capacity, and their pH decreases with time. Furthermore, lime mud has finer particle sizes and thus a greater specific surface area than most forms of commercially available calcite, which results in enhanced reactivity. Dissolved metal concentrations are similar in tailings slurries treated with lime mud or calcite. This study suggests that lime mud is an environmentally and economically attractive alkaline amendment for oxidized mine tailings.

Nov 1, 2002

By C. Dirscherl, M. Combes

"Declining ore grade, leading to increased material transport and plant throughput requirements, is one of the major challenges in the current mining environment. This is accompanied by rising energy and labor costs, decreasing plant productivity and the requirement for highest plant availability. Siemens’ answer is the latest gearless drive technology for grinding and conveying. Gearless drive solutions are surpassing the mechanical limits of conventional drive systems serving to utilize the principle of economies of scale. By elimination of various components of the drive train the maintenance activities and spare parts inventories are reduced. The advantages are culminating in the incomparable availability of the Siemens’ gearless drive technology of 99.46 to 99.71% - as confirmed by real operational data from the Antapaccay mine in Peru. It was the first plant worldwide to use gearless drives for both applications.INTRODUCTION – THE GEARLESS PRINCIPLE The principle idea behind a gearless drive system is to reduce the number of components and diversity of parts. Especially those components that are at the edge of current manufacturing or power limits are eliminated. The used equipment provides the possibility to scale up and increase the power transmitted to the driven machine. This finally results in a possible increase of throughput respectively transported or processed material. In order to apply this principle of simplification we will take a look at the components of a conventional drive system consisting of: - Driven equipment (mill, conveyor, slurry pump) - Components altering the rated speed (gearboxes, girth gear / pinion) - The electric motor - Starting devices for the motor (VSD, CCV, LRS, clutch), which are necessary because a direct across-the-line start of high power motors with load would result in a significant drop in the line supply voltage - Alternatively a variable speed drive (VSD) or cycloconverter (CCV) to utilize the possibility of speed variation during operation - The electrical supply system (cables, switchgear, transformers, protection equipment)"

Jan 1, 2014

By Georges Houlachi, Akram Alfantazi, Maysam Mohammadi

Manganese ions in zinc electrowinning electrolytes form a protective MnO2 layer that ultimately decreases Pb contamination in the zinc product. In this study, the effect of dissolved Mn2+ on the electrochemical performance of Pb, Pb-Ca and composite Pb-MnO2 anodes was investigated. The properties of the MnO2 layer formed on these anodes were studied and compared. Potentiodynamic polarization and cyclic voltammetry experiments were performed in 180 g L-1 sulphuric acid to study the electrochemical reactions occurring on the anodes. The anodes were subjected to galvanostatic polarization at 50 mA cm-2. The morphology and uniformity of the MnO2 layer on the anodes were examined using scanning electron microscopy (SEM). Experimental results revealed that the MnO2 layer formed on the composite anode was more compact and uniform compared to that formed on the Pb and Pb-Ca anode. It was also observed that the cell mud formation rate, and consequently manganese ions consumption, depended on the anode type. Although initial formation of the MnO2 layer decreased the oxygen evolution overpotential, its growth might negatively affect electrocatalytic activity of the anodes.

Jan 1, 2014

By Benoît Demers

Dans ses opérations de traitement de concentré de zinc, l?usine de Zinc Électrolytique du Canada à Valleyfield génère un résidu minier appelé « jarosite ». Jusqu?en 1998, le jarosite était transporté hydrauliquement dans des bassins construits en argile. Le jarosite sédimenté possède une consistance très molle (impossible de circuler à pied sur le résidu consolidé) avec une eau interstitielle acide contenant des teneurs élevées en métaux. Ces caractéristiques particulières au jarosite rendaient très coûteuses la construction et la fermeture des bassins de résidus. En 1998, Zinc Électrolytique du Canada a implanté un nouveau procédé, développé chez Noranda, dont le principal objectif était de stabiliser chimiquement et physiquement le jarosite. Un nouveau concept de déposition a été élaboré pour le nouveau résidu minier appelé « jarofix ». Les grandes caractéristiques du nouveau procédé et du concept de déposition sont : ? Le jarosite est lavé et déshydraté à l?usine avec un système de filtre; ? De la chaux, du ciment et de l?eau sont ajoutés pour former le jarofix; ? Le jarofix est transporté par camions jusqu?à l?aire d?accumulation; ? À l?aire d?accumulation, le résidu est géré selon un concept d?empilement. L?élaboration du concept d?empilement et de l?aire d?accumulation devait tenir compte des caractéristiques de déposition du jarofix, de sa résistance à l?érosion hydrique et éolienne, de la gestion de l?eau de ruissellement, de la faisabilité de construire les digues de ceinture en utilisant du jarofix durci et de la nécessité de restaurer progressivement l?aire d?accumulation. Le déchargement du jarofix se fait à partir d?une rampe qui progresse avec une pente ascendante pour développer un front de déversement de plus en plus haut. La hauteur du tas de jarofix atteindra 30 m au centre du site. L?aménagement initial de 1998 a inclut une digue d?amorce de 3 m de hauteur, une rampe de déversement de 8 m de hauteur et un bassin pour la gestion de l?eau de ruissellement. Les propriétés du jarofix consolidé dans l?aire d?accumulation sont déterminées annuellement. Le jarofix durci possède la consistance et la résistance d?une argile très raide. Sa conductivité hydraulique est similaire à celle d?un silt et il résiste bien à l?érosion éolienne. Après trois années de déposition, la température du jarofix au milieu du dépôt demeure élevée. Le jarofix durci est facile à excaver et à compacter, ce qui en fait un excellent matériau pour la construction des digues de ceinture en périphérie du site.

Nov 1, 2002

By Seong-Taek Lim

Recently, 7xxx aluminum alloys have been evolved into new variants for thick semiproducts which have low amount of 2nd phases and low quench sensitivity. Commercial 7xxx alloys, especially in the thick forgings made of big ingots, often entail microstructural inhomogeneities and concurrent poor mechanical properties due to limited heating ranges and slower quench cooling. In this study, high strength aluminum alloy 7175 and 7050 are adjusted as an attempt to control the equilibrium phases (M-, T- and S-phase) to have optimum microstructure for the thick forging applications. The effects of the relative content of (Zn, Mg, Cu) on the evolutions of the coarse equilibrium phases, hardening response and resultant mechanical properties are investigated. Equilibrium phases (M,T,S) are evolved depending on the constitutional effect, primarily the change of Zn:Mg ratio, and cooling rate following solutionizing. The formation of the T- and S-phases is effectively controlled, and M-phases are homogeneously precipitated in the adjusted (dilute and high Zn:Mg ratio) alloys. It provides extended heating range and lower quench sensitivity than conventional alloys. The attempts ensure the microstructural homogeneity and improved properties, and is expected to be uniquely applicable in 7xxx thick forgings.

Jan 1, 2004