Search Documents

By Zia Pirzada

"Time is of the essence" and "Time is money" These are powerful and true statements during a project life cycle and have far-reaching implications on the success and failure of the project Time and progress management is crucial to the project success. Project delays may increase the cost to an unacceptable level and may render the project as economically unfeasible. On the other hand, if the project is completed on time or earlier than as planned, it may generate economic benefits greater than what had been envisioned To take advantage of the financial opportunities and to improve the cash flow as well as Return On Investment (POI), project schedule can be accelerated to complete the project earlier than planned Project schedule acceleration can be achieved by using analytical tools, such as "Schedule Optimization", "Schedule Reduction", "Schedule Compression" or a combination of any of these concepts along with the "Planning for start up". Schedule optimization does not entail any extra cost, however, other acceleration methods, such as Schedule Reduction and Schedule Compression, may require extra expenditures from the owner. Based on the forecasted early start of the revenue stream, the extra expenditure could become a worthwhile venture with a very high rate of return To accelerate the schedule, all aspects of the project should be reviewed with acceleration costs calculated. All risks and opportunities should be evaluated and taken into consideration to determine if the acceleration is feasible and advisable and will provide definite financial advantages Sometimes schedule acceleration may be desired to prevent the company from paying liquidated damages. This is especially true when the project is not expected to complete on the contractual completion date and when the cost of acceleration is less than the liquidated damages that may accrue against the company.

Oct 1, 2010

By James D. Hall

THIS essay deals with the materials and methods used in the waste filling of scopes in Canadian mines, with especial reference co the methods used at the Sullivan mine, Kimberley, B.C. The author would like to thank members of the staff of the Sullivan mine for information obtained, and acknowledges material from the following publications: Waste Filling of Stopes: Information Circular 6816, U.S. Bureau of Mines. Mining Methods and Practices at Lake Shore, by Leslie S. Weldon; Trans., C.I.M. & M., Vol. XXXIX, 1936, pp. 142-202. Development and Mining (at the Mcintyre Mine), by D. E. Keeley; Eng. & Min. Journal, November, 1933. INTRODUCTION Although mining in Canada is a relatively youthful industry, many of our mines have reached a stage of extraction which requires waste filling, both as a means of support and co make possible the winning of ore that would otherwise have co be left in the mine. Fill may be used at regular intervals as one of the cycle of operations, as in cur-and-fill and square-set scoping; or it may be introduced into a completed stope co provide permanent support for overlying rock formations, and co permit mining of pillars of valuable ore. Waste fill is sorted in resuing, which is a form of cut-and-fill scoping employed in narrow veins.

Jan 1, 1937

By Gavin A. Hunt

In order for mines to operate profitably throughout their life it is important to monitor and maximise ore recovery. A common problem facing many mines is the underestimation of clay type and its distribution in ore at the mine face, blast hole or in the ore stockpile. Too much clay entering the heap leach ore stream for example causes a dramatic reduction in heap leach efficacy and or increased leaching times. The end result is poor leaching performance and much reduced metal production. Poor clay identification and quantification is attributable to many factors, including costly and slow off-site mineral analysis techniques, such as XRD, XRF and petrology, the visual and subjective limitations of the core logging geologist and a lack of suitable low cost, high throughput mineral logging instruments. To get round these problems a new, non-contact, imaging spectrometer - the SpecCam - was developed by Spectra-Map Ltd, to allow high throughput identification and quantification of minerals from mineable material. Its novel imaging design can collect millions of data points (pixels) per day; each pixel contains spectral information that allows a wide variety of mineral types, including the smectite and illite clays, and phyllosilicates such as talc and kaolin, to be identified. Because all the ore can be imaged a much more reliable mineral log can be made. Hence, mapping changes in mineral composition - related to variations in phenocrysts, macrocrysts, veining or wall rock - is possible. Examples of SpecCam data from Goldfields Cerro Corona Porphyry stockpile and from Rio Tinto?s Argyle Diamond mine illustrate the mineral identification and quantification capabilities of the SpecCam. More importantly, for the first time very accurate % abundances for the different minerals can be obtained using an image-based modal count technique. The modular design of the camera, plus its extremely flexible high speed filter, mean that the SpecCam can be easily installed on different equipment, each one suited to different ore recovery problems. For example the SpecCam can be used on an automated portable logging frame to measure drill core, RC chips, hand samples or powder, or alternatively installed on a Geotek multi-sensor core logger for high-throughput, automated logging of drill or blast hole core using co-registered multi-sensor data. An exciting recent development has been the installation of the SpecCam on CommoDas ore sorting equipment, used around the world for 24 hour mill-feed monitoring and automatic ore sorting. Real-time ore sorting decisions can be made as material is monitored on a conveyor belt running at 3m s-1, from which the ore can be automatically sorted into high-grade, low-grade or waste streams for example. The three installation options for the SpecCam mean that most mineral analysis and automated core logging or ore monitoring needs can be met at the mine. For the first time rapid and automatic mineral identification and accurate quantification can be made. All of which allow the mine geologist or metallurgist to make important decisions about maximising the metal recovery process.

May 1, 2007

By M. J. Nicol, T. Moyo

Ammoniacal solutions are an effective lixiviant for the oxidative dissolution of some mineral sulphides. A detailed study of the anodic dissolution of chalcopyrite in ammonium sulphate-ammonium hydroxide solutions has been carried out using cyclic voltammetry, chrono-amperometry and rest potential measurements. The role of the copper(II)/copper(I) redox couple in the oxidation process has been evaluated. Rest potentials have been found not to be affected by oxygen but to increase with an increase in initial copper(II) concentration. Pseudo-steady-state anodic current densities measured in the absence of copper(II) ions at the rest potentials obtained in the presence of copper(II) ions increase with increasing concentration of copper(II) ions, confirming the positive effect of copper(II) ions on the rate of dissolution of the mineral. Cyclic voltametric and chrono-amperometric data show that in the absence of initial copper(II) ions, the rate of dissolution in the presence of dissolved oxygen is significantly lower. These results confirm that the effective oxidant for the mineral under the conditions of the study is copper(II) and not dissolved oxygen. Coulometric measurements have been used to establish the stoichiometry of the anodic reaction at different potentials.

Jan 1, 2014

By W. E. Cockfield

This paper is not intended as an original contribution to this subject, but rather as a review of the main theories which are held with regard to placer deposits, with, of course, particular reference to the placers of British Columbia. The present interest in gold mining has, however, brought the subject of placers to the fore, and possibly a brief outline of the geology of such deposits will serve as a basis for discussion on the subject. In Canada, the most valuable of our placers are deposits of gold, and consequently the discussion will centre largely on placer-gold deposits. The same principles apply, of course, to placer deposits of other metals. The Origin of Placer Deposits As a starting point, the idea which is prevailingly held is that placer or alluvial gold is detrital in origin, that is to say, the gold originally existed in veins, lodes, or disseminations in the country rock of the regions in which the placer deposits are now found, and that, through the various erosive forces of nature, it was liberated from those veins or lodes and concentrated in the form in which we now find it. 1 have not time to go thoroughly into the proof of this, but the lines of evidence are many. If we take the Cariboo district as a typical example, Johnston and Uglow(l) have shown, first of all, that the placer and vein gold are identical in character. Crystals occur both in the placers and in the lodes, but the crystals in the placers are nearly always slightly worn, indicating transportation.

Jan 1, 1932

By John H. Fowler

Nova Scotia has been mining and exporting industrial minerals for over two hundred years. As an industrial mineral producer, this province continues to rank as the number one gypsum mining and exporting region in North America. Mining of many other commodities is ongoing, supplying many local and export markets. In all, excluding aggregate producers, there are nineteen industrial mineral producers operating at thirty sites producing nine commodities including anhydrite, barite, clay and shale, dolomite, gypsum, limestone, salt, silica sand and stone (Fig. I). Numerous aggregate producing operations supply all the province's aggregate requirements and export some of these materials to other regions of Atlantic Canada and as far away as Bermuda (Fig. 2) . Production value of industrial mineral commodities in Nova Scotia for 1982 was $105 million , representing 39% of the total value for all mineral production for the year. Because of the general improvement in the economy, indications are that the 1983 value of production will be higher.

Jan 1, 1984

By J. R. Tickner

"Gold is conventionally analyzed using fire-assay or other destructive chemical methods that impose significant sample preparation, OH&S, and skilled labour requirements. Developed over the past 15 years by the CSIRO, PhotonAssay provides a new approach. A high intensity, high-energy x-ray source is used to activate atoms of gold and other elements in bulk mineral samples. The resulting activity is counted to automatically, accurately and rapidly determine metal grade. Samples weighing 0.5–1.0 kg can be measured in a few minutes with minimal preparation. As the method is matrix-agnostic, traditionally hard-to-assay materials such as highly refractory ores, carbon pulps and copper concentrates require no special treatment. We present the status of commercial PhotonAssay systems being developed by Chrysos Corporation. The first unit with a throughput of up to 80 samples per hour is to be deployed in an Australian assay laboratory in late 2017; smaller systems suitable for providing real-time assay directly at the mine-site will be progressively rolled out from mid-2018. Performance results from extensive testing using both mine-sourced and standard reference materials are presented, demonstrating the sensitivity and accuracy of the method. Implications for replacing conventional gold assay in exploration, mining and processing operations are discussed.INTRODUCTION Accurate methods for assaying ore grade are essential throughout the exploration, mining and mineral processing value chain. The discovery and evaluation of new ore deposits, reserve and resource definition, mine operations planning, ore processing, metal accounting and product quality evaluation all rely on accurate measurement of the valuable metal content of bulk materials. The analysis of gold presents particular challenges, stemming from the very low concentrations at which commercial operations run (often part-per-million (ppm), or equivalently one gram-per-tonne levels or below), and the highly heterogeneous nature of many gold deposits. These challenges mean that any analytical method must have high sensitivity and be capable of measuring large-mass samples. The most widely used quantitative analytical method for gold is fire-assay (Hoffman, Clark and Yeager 1998). An initial ore sample typically weighing several kilograms is dried, crushed and pulverized to allow a small sub-sample (10–50 g is common) to be representatively drawn. The sub-sample is mixed with flux, litharge (lead oxide), a reducing compound and other reagents. The mixture is fired at a temperature of 1000–1200°C until molten. After cooling, the slag is removed and the lead button containing any gold present in the sample is remelted in a porous cupel. The lead is absorbed into the cupel, leaving a gold prill which is either weighed directly, or dissolved in acid and analysed via atomic absorption spectroscopy (AAS) or inductively coupled plasma spectroscopy (ICP or ICP/MS)."

Jan 1, 2017

By B. Morrison

"The Kiruna Electric System is a recently developed inclined ore haul age system for underground mining operations. Although an initial investigation was carried out at the Swedish underground iron ore mine LKAB almost three decades ago, it was not until 1981 that the resources of LKAB, ASEA and Kiruna Truck AB were combined to investigate, and subsequently develop an ""all- electric truck"" for the mining industry.It has long been appreciated, that major economical advantages could be realized by a mining operation through an extension of the cost-effective life of the existing ore hoisting system by the use of ramps to haul ore up to the main haulage level. Diesel truck s have been used and are being used for ramp haulage. Their use however, is limited due to ventilation and operating costs restraints.There are numerous instances of orebodies, located within a couple of hundred metre s of surface, or below an existing hoisting facility, being developed by ramp access while the shaft is being sunk. Development of an orebody via ramp access has many advantages to a mining operation where mechanized mining is to be practiced. These advantages are both practical and economical; generally falling within the over-all umbrella of the phrase ""cash flow"" mining.The decision to sink a shaft is a major committment by any mining company, regardless of size and financial reserves. Extensive diamond drilling, both shallow and deep must be carried out before a decision can be executed. This constitutes a major financial expenditure over an extended period of time.The decision to sink a shaft must be weighed against the reliability of geological interpretation of the deep diamond drilling results, the stability of the mineral market and potential fluctuation in ore prices and interest rates."

Jan 1, 1989

By H. C. Cooke

Geological examination of the underground workings of the Horne and Aldermac mines during the summer of 1927 has brought out the following facts: (1) That the ores tend to replace bodies of breccia or tuff rather than massive lava or dyke material; (2) That the faulting and folding at the Horne has had a pronounced effect in localizing the ore-bodies; (3) That there is a tendency in cert?-in cases for ore-bodies to be localized beneath gently dipping dykes, which acted as impervious roofs; (4) That there is a great difference in age between the chalcopyrite part of the ore-bodies and the pyrite-pyrrhotite portion. A statement of the development to date at the Aldermac mine is also included in the paper. ALDERMAC MINE The Aldermac property is made up of eight claims in the western half of Boischatel township, Quebec, including 747 acres in all. The mine itself is approximately three miles, 25 chains from the west boundary, and four miles, 55 chains from the north boundary, of the township.

Jan 1, 1928

By Fatemeh Pourakbari, Mohammad Reza Yarahmadi, Abbas Sam

Pyrite is the most abundant sulfide gangue mineral in copper porphyry ores. In spite of addition of lime in large quantities to depress pyrite in flotation, considerable amount of this mineral is reported to concentrate, particularly in rougher and scavenger stages. With the Sarcheshmeh pit advancing to a greater depth and reaching to the hypogene zone, the amounts of pyrite and chalcopyrite in the feed are increased. Hence, a reduction in the copper grade and increase in the sulfur content of the concentrate are observed. In this study the effective factors on the pyrite floatability at the circuit flotation was considered at Sarcheshmeh Mine. Mineralization zones in the pit were firstly identified. Then, sampling points were located using GPS system. On the basis of mineralogical composition and morphology, the ore was categorized into five main classes. In this classification the amount of lead and zinc and also pyrite locking with other minerals were analyzed. The study of polished section indicated that inclusion in pyrite was very frequent in all classes, mostly composed of the floatability of pyrite. Flotation tests were performed on the samples of different classes at pH of 11.8 after conditioning time. It was shown that, pyrite floatability was decreased with a decrease in the lead content of the feed samples except for the second class, while for all classes an increase in zinc content contributed to a decrease in pyrite floatability and recovery. It was found that, the lowest pyrite recovery (1.89%) was corresponding to pyrite–molybdenite dominant mineralization with Zn of 0.33% and the highest recovery (86.89%) corresponding to pyrite vein dominant mineralization with Zn equals to 0.9%.

Jan 1, 2016

By J. A. Brown, F. P. Kerr, M. A. Archer

Extensive testwork on Global Atomic’s Dasa Project in Niger has been conducted at SGS Minerals laboratory in Lakefield, Ontario. Much of this testwork has focused on a two-stage counter-current leach as a means of improving leach efficiency and decreasing reagent consumption. The ore contains uranium mineralization requiring relatively high sulphuric acid concentrations during leaching to achieve acceptably high extractions. Excess free acidity in the leach solution may be utilized by recycling the high acid solution and contacting it with fresh ground ore. The resulting pregnant leach solution (PLS), now higher in uranium concentration and depleted in free acid, is forwarded on to uranium recovery by solvent extraction. The first stage residue proceeds to the second stage leach where fresh acid and oxidant are provided to leach the remaining uranium. This paper presents the results of the testwork conducted on both a Master Composite and Variability samples.

Jan 1, 2020

By L. C. Lien

Tower crane layout (TCL) is a typical construction site layout (CSL) problem, which is suitable for a wide range of work assignments and site conditions. Tower crane is one of the key facilities for vertical and horizontal transportation of materials, especially for heavy prefabrication units such as steel beams, ready mixed concrete, prefabricated elements and large panel formwork such as machinery and equipment, and a wide variety of other building materials within a construction site. However, it is a difficult combinatorial optimization problem to determine the locations of tower cranes with materials quantity supply and demand for engineers. Swarm intelligence (SI) was very popular and widely used in many complex optimization problems which was collective behaviour of social systems such as honey bees (bee algorithm, BA) and birds (particle swarm optimization, PSO). This study applied a hybrid swarm algorithm namely particle bee algorithm (PBA) based on a particular intelligent behaviour of honey bee and bird swarms by integrates theirs advantages. This study compares the performance of PBA with BA and PSO for a proposed hypothetical construction engineering of TCL with materials quantity supply and demand problem. Results show that PBA performs better performance than the mentioned algorithms on a proposed hypothetical TCL problem.

Aug 1, 2013

By M. Melashvili

"The SART Process was introduced to the gold mining industry in the late 1990s and several commercial plants were built over the following 10 to 15 years. Most of these plants have operated well and enjoyed plant performance in line with expectations based on the underlying chemistry of the process. However, two of the plants have consistently suffered from high reagent consumption and poor product quality, which has motivated a re-examination of the process fundamentals in the hope of understanding the reasons for poor performance when it occurs, and developing mitigating strategies.This testwork along with a review of the relevant literature has demonstrated that the amount of sulphide added to the primary reactor, relative to the copper concentration, is the most critical parameter dictating plant performance, with pH and residence time important secondary factors. The primary product in the SART Process is synthetic chalcocite, Cu2S, and the stoichiometric requirement for sulphide addition is therefore 0.5 moles per mole of copper in solution. Testwork shows that when sulphide is added in excess of this amount (generally with the express purpose of lowering residual copper in solution) it not only fails in its intended purpose, but can have a negative impact on the settling and filtration characteristics of the copper sulphide product, as well as the final product quality. Moreover, these problems are exacerbated the higher the selected operating pH in the pH 3 to 5 range, and the longer the residence time of slurry in this pH range.Freshly precipitated copper sulphide compounds are known to be very fine and slimy, with poor settling and filtration characteristics. It is therefore important to engineer the SART Process in such a way as to encourage growth in the average particle size of the precipitate crystals. This was the rationale for recycling a portion of the thickener underflow to the primary reactor when the SART Process was developed. The theory of crystallization predicts that compounds of extremely low solubility, such as chalcocite (Cu2S: KSP = 10-48), are likely to experience growth in crystal particle size through aggregation rather than heterogeneous nucleation. On this basis, the SART practice of recycling a portion of thickener underflow to the primary reactor in the commercial plants is unlikely to lead to crystal growth via nucleation, and could in fact promote breakage of the aggregates that formed in the thickener. Recycling thickener underflow could therefore have the opposite of the desired outcome. The result of testwork that is reported here lends credence to this theory and questions the wisdom of recycling in the SART process.There is evidence to suggest that operating the copper sulphide thickener in the SART Process without flocculants may be beneficial. Thickener underflow densities could improve from the current 10 - 15% range to 40 - 50%. This will not only reduce the flowrate of slurry to the filter, but the filtration properties of the slurry (filtration rate, filter cake moisture content) will also improve. This is one of the most critical engineering and design aspects of the SART Process, and the achievement of high solids density in the thickener underflow will not only improve the health and safety aspects of the operation, but also has the potential to lower capital costs and improve the quality of the final product."

Jan 1, 2016

By Kyle Selga, Christopher J. Greet

"The Pulp Chemistry Monitor (PCM) has been installed and operated in a number of concentrators in Australasia, and has produced some very interesting results. PCM measures the pH, Eh, dissolved oxygen, temperature and oxygen demand of process streams within a concentrator continuously and in real time.In the example presented in the paper the cleaner feed pulp chemistry is measured, and related back to changes in the mineralogy as well as variations in metallurgical response. For example, a decrease in Eh and dissolved oxygen as well as an increase in the oxygen demand. These changes in the pulp chemistry appear to coincide with increases in the feed grades, probably higher pyrite grades. Further, these variations in pulp chemistry and feed mineralogy have a negative impact on the concentrate grade and recovery.The implication is that if the pulp chemistry is monitored it is possible to predict changes in the mineralogy of the system, and from this the metallurgical response. Further, the changes in pulp chemistry can be used in a control system to counter the changes in mineralogy and maintain the metallurgy.IntroductionIt has long been recognized at a fundamental level that the flotation behaviour of sulphide minerals is dependent on the pH and Eh of the system (for example: Tolun and Kitchener, 1964; Woods, 1976). However, measuring pulp chemical parameters within an operating concentrator has had limited attention. Woodcock and Jones (1970a and b) were among the first to actually collect data from operating plants. Jones and Woodcock (1984) identified some of the chemical complexities of flotation pulps, and noted that most concentrators already operate at high levels of metallurgical performance but there was still considerable scope for improvement. These gains would, in part come from more effective chemical control. In the same volume, Healy (1984) discussed metal ion hydrolysis and precipitation, redox chemistry and how the surface chemistry of sulphide minerals can be influence flotation behaviour. The impact of grinding environment on the pulp chemistry and flotation response of a complex polymetallic sulphide ore is discussed by Forssberg and Subrahmanyam (1993). Their work essentially contrasts the pulp chemical and flotation performance of pulps ground with conventional ferrous grinding media to a fully autogenous system. The data suggested that the reduction or removal of iron hydrolysis contamination from the system could have a positive influence on flotation behaviour, and perhaps the first stage of “controlling” the chemistry of the system should be in the grinding circuit. Grano et al (1995) demonstrated that the collection of pulp, solution and surface chemical data could identify weaknesses within a concentrator, and from these data develop, test and implement solutions that improved the process. Greet et al (2006) showed that the pulp chemical trends observed through primary grinding and rougher flotation circuits of most sulphide flotation concentrators are approximately the same. There are differences in the magnitude of various pulp chemical parameters (pH, Eh, dissolved oxygen, temperature and oxygen demand) as a result of variations in the feed mineralogy and processes employed. Further, it was noted the Eh shifted to more reducing values of the ten days measurements were collected, and this change could be traced to an increase in the iron sulphide content of the feed. Metallurgically, this resulted in an increase in nickel recovery through the recovery of nickeliferous iron sulphides, and a decrease in nickel concentrate grade."

Jan 1, 2016

By J. Suarez

The innovation initiatives for world-class mines today and in the future focus on automation and robotics in equipment and machinery. These innovations have benefited from the development of advanced tools in global positioning, the Internet, the capabilities of data storage, transmission and handling, and intelligent systems. Forward-thinking companies have been investing in automated trains and trucks, selfdrilling rigs, intelligent flotation systems, etc. Considering that the emphasis has been mostly laid on improving the performance and reliability of the equipment and machinery, it is not surprising that the visibility was geared toward mechanical, electrical, process, and metallurgical engineering. One of the critical disciplines, mining engineering, has had less shine from the spotlight of automation and robotics. Mining engineering is concerned with the design, the operation, the management, and the reclamation of mines and mining facilities. In essence, it does benefit from the advantages of automation and robotics in equipment and machinery. However, being ?left out? in the innovation process may impede the core capabilities of this engineering discipline, which would create a two-tier knowledge and technology system in mines. For example, shovels in an open pit may be equipped with technology that can send real-time data of actual payload, number of buckets, mechanical status, etc. But, are mining engineers aware of the possibility to incorporate the data into their planning tools in order to have updated forecasts and accurate information? And if they are, are they equipped with the tools to reap the rewards of those technologies? And if so, is the personnel trained to use the tools efficiently? This paper is a contribution to the discussion on the technological advances in mining engineering. For the authors, the roadmap to the future requires a smart integration of technological advances in hardware and software so that mining engineers are not only aware of the possibilities, but also trained and capable of using the available tools. Essentially, this paper believes that automation and robotics in equipment alone will be undervalued and underutilized if the owners and drivers of the mining systems (i.e. the mining engineers) do not possess the tools and training to integrate the technological advances into the functions of mining engineering. The intent of the paper is to analyze the available technologies for the core mining engineering functions of design, planning, scheduling and optimization. The analysis will lead to discussions and suggested solutions on integrative technology solutions that would create optimum value for the mining processes and equipment technologies.

Aug 1, 2013

By Yin Guangzhi, Song Zhenlong, Li Minghui, Li Wenpu, Deng Bozhi

"Darcy's law is widely used to describe the oil and gas flow characteristics in the multi-pore media reservoir. However, the low-velocity non-Darcy flow of oil and gas occurs in the multi-pore media reservoir under low permeability conditions. Meanwhile, the high-velocity non-Darcy flow of oil and gas occurs in the multi-pore media near the wellbore. The gas flow velocities in coal in different deformation stage under different gas pressure gradient were tested and the relationships between gas flow velocity and gas pressure gradient were discussed, which can help us to investigate the transformation conditions of gas linear flow and gas nonlinear flow in coal. The results showed that the gas flow in the coal under low effective stress environment can be described by Darcy's law. The low-velocity non-Darcy flow of gas gradually occurred and the start-up pressure gradient increased in the coal as the effective stress increased. The low-velocity non-Darcy flow of gas also occurred in the coal at the yield deformation stage, however, the start-up pressure gradient decreased as the effective stress increased in this stage. In post-peak stage, the highvelocity non-Darcy flow of gas occurred in the coal under low effective stress environment. The gas flow in the coal gradually returned to be Darcy flow as the effective stress increased. The mechanism of the phenomenon is discussed based on the experimental results. The research results can be used to guide well test analysis and prediction of oil-gas production. INTRODUCTIONThe oil and gas flow in original multi-pore media reservoir are usually regarded as steady and linear processes and can be described by Darcy’s law. However, the low-velocity non-Darcy flow of oil and gas occurs in the multi-pore media reservoir under low permeability conditions. Meanwhile, the highvelocity non-Darcy flow of oil and gas occurs in the multi-pore media near the wellbore or workface. The gas flow in the multi-pore media even may be unsteady under some conditions such as gas emission and outburst.The phenomenon of underground water low-velocity flow in clays was deviated from Darcy’s law was found in the end of the nineteenth century (King, 1898). The deviation from Darcy’s law was later reported and investigated more (Swartzendruber, 1962; Miller and Low, 1963). These researches revealed that the start-up pressure gradient exists under low permeability conditions. Klinkenberg (1941) proposed that the permeability constant as determined with gases is dependent upon the property of the gas, and is a linear function of the reciprocal mean pressure. This effect can be explained by taking into account the phenomena of slip, which are related closely to the mean free paths of the gas molecules."

Jan 1, 2015

By A. V. Corlett

MR. C. S. Gibson: Mr. Chairman, I listened with much interest to Mr. Corlett's paper. Those of us who are directly engaged in mine ventilation and dust control are impressed by the improved atmospheric conditions to be derived from the use of methods of mining such as those in operation at Aldermac, which Mr. Corlett has just described, and those employed at Noranda. It is a well known fact that drilling-dust is one of the most potent factors in the production of silicosis in mines handling ores containing quartz, so that from that angle the use of diamond drills, instead of percussion drills, to drill ore for blasts in stopes is an important development. A second point which I think merits mention is blasting. Blasting, we all know, creates the most dust in a mine and the fact that you can drill ore for a large blast with diamond drills and fire it, say, on Saturday night, and then have all the next day to ventilate the workings, is a great advance in dust control. 1 have wondered if Mr. Corlett, or possibly those at Noranda, can en-vision the use of the diamond drill as a means of advancing cross-cuts and drifts, preparing stopes, etc. I believe it is a matter which is receiving considerable attention at the moment in some parts of the world and J thought it would be interesting to have Mr. Corlett's reaction on that point. MR. A. V. CORLETT: I am not quite so hopeful of using diamond drills as a means of drilling holes in the ordinary drift. Maybe some of the diamond drill men can give us some further information on that point. MR. R. D. LoNGYEAR: The diamond drill manufacturers are working on that problem, but until further work is done we have nothing definite to offer. Drilling holes with a diamond drill to compete with rock drills for advancing drifts and cross-cuts is a desirable objective, because of the elimination of drilling dust and the ability to cut a smooth bore of uniform diameter. To reach this objective, higher rates of penetration are required, which can only be achieved by discovering the optimum bit rotating speed, by reducing vibration, and by further improving the bits and machines. We are optimistic, but the problem is still largely in the research stage.

Jan 1, 1940

By Roger D. Plouffe

In today's mining industry, it is possible to retrieve, from small-diameter holes, geophysical data for qualitative interpretation in exploration and quantitative interpretation in the development of orebodies. The primary objectives in the exploration stage are to identify where, within a hole, economic minerals are, and to help in lithological interpretations. Other aspects, which are more quantitative, are the interpretation of downhole logs for parameters which can be used in surface geophysical methods (i.e. density for gravity surveys, acoustic velocities for seismic surveys, and magnetic susceptibility for airborne and ground magnetic surveys). Recent advances in equipment design, portability and durability have made downhole logging in exploration more inexpensive and reliable. This new equipment is being used to generate very precise quantitative results. This is especially true on uranium development projects. The interpretation of gamma logs for eUJOS values has finally become precise enough that they have begun to replace chemical values in reserve calculations. Another part of development data is density and equilibrium information, which, with today's technology, is being derived from downhole probing. In the years to come, the trends for many metals are toward neutron activation techniques, or "in-situ assaying", and the use of multiple logs for better lithological and physical rock property determinations.

Jan 1, 1981

By L. O. Cooper

IN THE operation of most mines, hoisting ropes, made of steel, play a very important part in the conveying of men and material between surface and the underground workings. It is obvious that, in order to maintain a maximum degree of safety, certain restrictions must be placed on the loads that may be carried by hoisting ropes, as well as on other factors that may affect the life of the rope. It is the purpose of this paper to suggest ?a new method of defining the necessary restrictions. The three main stresses in a hoisting rope are the static stress, bending stress, and dynamic stress. Crushing stresses, which are also present, are largely indeterminate and may best be allowed for by proper grooving of drum and sheaves, by adequate inspection of cross-over points, and by limiting the number of layers on the drum. They will, therefore, not be considered in this analysis. In the ?recent Ontario regulations, the limiting conditions for the main stresses are specified separately. The static stress is limited by setting a minimum static safety factor of 5.0 The dynamic stresses are allowed for by specifying a minimum capacity factor of 8.5, which has the effect of increasing the safety factor required at smaller depths in a uniform manner. The bending stresses are limited by calling for a drum-dia./rope-dia. ratio of at least 60 for ropes up to 1 inch in diameter and 80 for ropes greater than 1 inch in diameter. One disadvantage of this method is that the controls are too rigid and do not allow the operator sufficient freedom of action within safe limits.

Jan 1, 1951

By S. Onuki, T. Ando, M. Tejima, R. Enomoto, Y. Okada

"Al–Si–Cu–Mg die casting alloys are widely used in the automotive industry, and recent advancements in high pressure die casting technology enable heat treating products to achieve desirable properties. However, CO2emissions associated with die-casting production lines should be reduced to address the global warming issue. In this study, the relation between the microstructures and thermal stability of precipitates formed during isothermal aging at 423, 485, and 558 K of Al-11.0 mass%Si-1.8 mass%Cu-0.2 mass% Mg (JIS ADC12) was investigated using Vickers hardness tests and transmission electron microscopy (TEM). The hardness tests and TEM results showed that Si compounds and Al–Cu compounds enhanced the mechanical properties of the alloy and that the predominant compound affecting the mechanical properties differed between specimens treated at 423 K and those treated at 558 K. Moreover, additional aging at 423–458 K resulted in a material with a Vickers hardness higher than that of the isothermally single-aged material. Differential scanning calorimetry, differential elemental analysis, and selected-area diffraction analysis using TEM suggested that the combination of Al–Cu compounds precipitated at low aging temperatures and Si compounds precipitated during preliminary aging increased the mechanical strength, resulting in a maximum hardness of 130 HV.INTRODUCTIONAl–Si–Cu–Mg die casting alloys have well-balanced mechanical properties, machinability, and cast ability. These alloys are therefore widely used in the automotive industry because of their superior characteristics, accounting for>90% of the aluminum used in die casting production. As a substitute for iron-based materials, these alloys have contributed to the development of lightweight vehicles.Dong et al. (2014) reported that the heat treatment of die casting materials is effective for changing their dimensions under high temperatures as a result of the precipitation of solid-solution elements. Recent advancements in high pressure die casting technology have led to the application of heat treatments of Al–Si–Cu–Mg alloy products to reduce fuel consumption and satisfy customer needs. Although attempts to reduce CO2emissions have focused on fuel consumption in cars and fuel efficiency regulations have become increasingly strict in recent years, CO2discharged from production lines should also be reduced without adversely affecting the properties of the product. Heat treatments for artificial aging after solution treatment (T6 treatment) and after casting (T5 treatment) are CO2discharge sources, which together with a holding furnace account for >80 % of the CO2discharged during the casting process."

Jan 1, 2018