Search Documents

By Jose R. Hernandez-Aguilar, Jeet Basi

"The study evaluated the impact on overall circuit metallurgy of improving the performance of the two flotation columns that make up the final Mo cleaning stage in the Cu/Mo separation circuit at Highland Valley Copper mine. The results showed that a key factor to improve the overall circuit metallurgy was to control the size of the bubbles generated in the columns. When a large proportion of small (< 1 mm) bubbles were generated, the production rate of solids-in-concentrate increased by a factor of 4-5 compared to typical production figures without compromising concentrate quality. This increase in concentrate production rate reduced the circulating load in the circuit causing a significant increase of Mo recovery. A statistical analysis of historical production data showed a strong relationship between final concentrate production rate and overall Mo recovery. This relationship along with the results from this study indicated an opportunity to increase the recovery of Mo from 90% (typical) to 94% without downgrading concentrate grade. This 4% increase represents about 14,000 lbs or $500,000 worth of Mo each month at current metal prices.To provide a rational interpretation of the results, this study also examined whether the model of Gorain et al. (1997; 1998; 1999) could explain the increase of Mo recovery seemingly resulting from the decrease of bubble size. The data showed that the model predictions did not agree with the experimental data, i.e., for a given change (decrease) of bubble size, the predictions underestimated significantly the observed recovery increase. An interpretation based on the fundamental analysis of Finch and Dobby (1990) and Hernandez-Aguilar et al. (2005) is proposed to explain the discrepancy between measurements and predictions obtained from Gorain et al.’s model.INTRODUCTIONIt is generally accepted that the size of the bubbles generated in a flotation cell – a concept usually referred to as “bubble size” – has a significant effect on metallurgical performance. However, a significant number of mineral processing practitioners often question, with valid reasons, the practical benefits of implementing process improvement strategies based on controlling bubble size. “Small” bubbles are often considered to be “favourable”, but how small they need to be for a particular case, or how to adjust operating conditions to control a target bubble size, or whether the bubbles need to be smaller in the first place are questions that usually remain unanswered. Two reasons explain this situation."

Jan 1, 2009

"The first SkimAir flash flotation cell was installed in Outokumpu’s Hammaslahti Copper Concentrator in 1982 to prevent overgrinding of soft sulphides in the milling circuit. Since this first installation the popularity of the flash flotation has fluctuated depending on metal market conditions and regional preferences. Units have been installed in many commodities including copper, lead, gold, PGMs, silver and nickel. Though it has been successfully employed in many operations around the world, flash flotation technology is still not well understood by many in the mining industry. This paper will discuss aspects of flash flotation flowsheet development along with some of the metallurgical and engineering considerations required to successfully incorporate flash flotation into new or existing milling circuits. This paper will also try and debunk some of the myths that exist around flash flotation cells and their operation. Case studies of flash flotation implementation will be discussed.IntroductionModern flash flotation technology was developed several decades ago by Outokumpu, with the first commercial installation of this technology being at the Hammaslahti concentrator in Finland in 1982 (Kallioinen & Niitti, 1985). This was a relatively modestly sized SK80 cell producing final grade copper concentrate directly from the flash flotation cell operating in the grinding circuit. Since that time the size and number of flash flotation cells installed globally has grown considerably to the point where today, it is a widely known application of flotation technology for amenable ores. Owing to their long history in developing the technology, Outotec are the market leader with their SkimAir range of flash flotation cells. Though there is a general awareness of flash flotation process in the mineral processing industry, there is a lack of detailed understanding of the process and the benefits it can provide to new and existing operations."

Jan 1, 2017

By Andrew Kerr

Overview of Presentation ? Introduction ? An historical context: From 1866 to the 21st century. ? Geological framework for iron ore in the region known as the ?Labrador Trough?. ? Producing iron-ore deposits of the Labrador City ? Wabush area, and near-future production from the Schefferville area. ? Exploration projects representing potential future production?.or expansion of the district. ? Some concluding remarks???

May 1, 2011

By Corrie Pitzer

Safety performance in many companies and even industries has stalled in the few years. Accidents rates are at a ?plateau? and yet, serious accidents and fatality rates are not. In more dramatic cases, such as in the BP Texas disaster, organizations that have ?exemplary? safety statistics, suddenly have a catastrophic or multi-fatality event occurring. Other classic examples are the Piper Alpha disaster and NASA?s Challenger and Columbia disasters and even the Chernobyl nuclear reactor. Looking into the root causes of these accidents provides an insight into the events and deficiencies that led up to the accident, but what are the common features in the organization?s mindset? What characterizes these organizations? decision making, their approach to safety and to risk and are there specific cultural features that can be delineated? The research and review presented in this paper covers a period since 1994, which started in the Australian resource industry and since then covered international events. The features of these organizations are summarized as the seven deadly delusions, based on extensive research since 1997 of organizations that suffered unexpected disasters. Their huge focus on safety, the achievement of lofty goals and celebration of safety successes led to ?mindset? that they are leaders in safety, protected by an extraordinary safety system and that their safety incident figures indicated a truly world-class safety performance. It led them into the trap of the seven deadly delusions?

May 1, 2011

By W. J. Young, K. B. Macneill, C. N. Smith

"A BRIEF HISTORY OF THE MURRAY BROOK MINERAL DEPOSITDuring the mid-1950's intensive exploration activity in northern New Brunswick followed the discovery of the world class Brunswick base metal deposit. Using the prototypes of modern airborne geophysical and geochemical exploration techniques many mineralized areas in the Bathurst-Newcastle area were quickly identified. This base metal - silver camp is situated within the metavolcanic - metasidementary rocks of the Tetagouche Group which forms a roughly circular caldera-chaped voloanio complex of Ordivician age.One of the early results in the exploration history in the camp was the discovery of the Murray Brook Deposit by Kennco Explorations, (Canada) Limited. During routine ground checking of geophysical anomalies, most of which turned out to be graphitic schist, the discovery of some copper bearing float was made by the exploration team. This encouraged the company sufficiently to carry out a regional stream sampling program which lead to a large anomaly associated with a hematitic gossan. Diamond drilling of a weak Slingram anomaly over the gossan zone resulted in the discovery of massive sulphide lenses. This was followed in 1956-7 with an intensive drilling program. The result was the delineation of a potential ore body containing an estimated 23 million tons with an overall grade of 0.44% copper, 0.86% lead, 1.95% zinc, 25.73 g/tonne (0.91 oz/ton) silver, 0.28 g/tonne (0.01 oz/ton) gold. Within this package were higher grade zones of copper and lead-zinc mineralization approaching ore grades.A thick blanket of gossan was present and is reported to have caused the drillers considerable trouble as they attempted to penetrate it to get to the underlying sulphides. The gossan, consisting of iron oxides and silica fragments sits on top of the massive sulphides and attains a remarkable thickness of 45.5 meters (150'). Early work had suggested that the gossan was enriched in gold and silver. If this were the case and if the precious metal could be leached out with cyanide, then mining and recovering those values might be economic.With this in mind Northumberland Mines Limited optioned the property from Kennco in 1985. Preliminary leach tests indicated that indeed the gold in particular leached readily. Subsequent drilling of the gossan (using triple core barrel technology for better recovery of the easily ground core) indicated 1,536,363 tonnes (1,690,000 tons) with an average grade of 1.05 g/tonne (0.037 oz/ton) gold and 42.13 g/tonne"

Jan 1, 1993

The importance of understanding the behaviour of cemented paste backfill (CPB) within the framework of the effective stress concept is highlighted in this paper. Only through an understanding built on this concept can problems such as barricade loads, the rate of consolidation and arching, be fully understood. The critical importance of the development of stiffness during the hydration process, and its impact on factors such as barricade loads, is used to illustrate why conventional approaches that implicitly ignore the effective stress principle are incapable of capturing the essential components of CPB behaviour.

May 1, 2007

By K. E. Barnes

"The IsaMill was developed for fine-grained ores that required at least double the grinding efficiency of ball or tower milling to be economic. This was achieved, but in practice, the benefits of using inert media (eg sand, slag, ore, ceramic) have proven to be at least as important as the higher grinding efficiency. Flotation selectivity and rate was improved for all particles, particularly fines. This allowed a dramatic simplification of the Mount Isa lead zinc flotation circuit – adding 6 MW of ultrafine grinding power reduced reagent addition and flotation volume and increased plant energy efficiency. This was quite unexpected.This paper examines four orebodies that were enabled by inert grinding – McArthur River, George Fisher and Black Star Open Cut Mines (complex fine-grained lead zinc orebodies in Australia), and the Western Limb Tailings Retreatment plant (a PGM operation in South Africa). In a unique case history, the operating performance of the Mt Isa lead zinc concentrator is explained by size-by-size mineralogical data collected over 25 years, systematically explaining the impact of declining ore quality, and the effects of additional conventional grinding, inert grinding, and circuit and reagent redesign.The mineralogical case histories are so compelling that it is argued that the advantages of inert grinding should not be confined to difficult, fine-grained orebodies. The availability of largescale efficient inert grinding mills could have profound impact on circuit design for many orebodies.INTRODUCTIONThe IsaMill was developed by MIM (now Xstrata) to enable the development of the McArthur River Orebody in the Northern Territory of Australia. This ultra-fine grained ore needed a grind size of 80% passing 7 microns to produce a saleable concentrate. Such a fine grind was not economic with conventional ball or tower milling. Below about 25 microns the low energy efficiency and high media consumption of these mills is prohibitive. Critically, the high steel consumption and associated change in pulp and surface chemistry also seriously affects flotation metallurgy."

Jan 1, 2006

By J. Kouam

Al-Si-Cu and Al-Si-Mg alloys are widely used in several applications. Although they can be produced near-net-shapes, products made of these alloys very often require some machining. The purpose of this study is to evaluate the machinability of A319 and A356 under TO and T6 conditions. The machinability was assessed using during dry drilling machining process and the machinability indexes used are the chip form, the chip breakability and the cutting forces. It is found that 319 and 356 exhibit different machinability behaviors, especially in the T6-condition in terms of forces requirements, chip breakability and chip segmentation. It is also found that both the microstructure of the workpiece materials and the machining conditions significantly affect the chip formation mechanism, and therefore, the machining parameters could be selected to promote a chip form that is easily manageable in production.

Jan 1, 2011

By F. Habashi

"While bioleaching of pyrite concentrates has been successfully used in industry to liberate gold from the sulphide matrix for subsequent cyanidation, the same technology cannot be recommended for leaching chalcopyrite concentrates for copper recovery. It will be shown to be uneconomical and cannot compete with pressure leaching technology. Data on the pilot plants that were constructed for this purpose and were shut down will be given.INTRODUCTIONBacterial leaching has been successfully applied for heap leaching of low-grade copper ores (Habashi, 1978, 1999). One of the major operations is that at Bingham in Utah (Figure 1). The leach solution collected at the bottom of the heap is extracted by organic solvents and the strip solution is electrolyzed to get high purity copper. The process was extended to treat auriferous pyrite concentrates to liberate gold and render it amenable to cyanidation by a process known as BIOX (Marsden & House, 2006; Lunt & Briggs, 2005).BIOX plants currently or recently in operation are the following:??Ashanti Goldfields Company, Ghana. Designed with an initial capacity of treating 720 tonnes of concentrate per day, the Sansu plant has since been expanded and currently has four modules processing 960 tonnes per day in all. It is by far the largest biooxidation plant in the world. The capital cost of the plant totalled US $25 million (1994 terms) and the operating cost is currently US $17/tonne milled.??Fairview, South Africa. The plant at the Fairview mine in Barberton, which was the initial pilot plant, has been fully operational since 1986. It was originally designed to treat 10 tonnes/day of concentrate but with the success of the project this has been increased to 55 tonnes per day. With the purchase of Fairview by Avgold’s Eastern Transvaal Consolidated, Avgold concluded a licensing agreement with Gold Fields, formerly known as Gencor, entitling it to use the BIOX technology to treat itsconcentrate.??Saõ Bento, Brazil. A BIOX plant was recently in operation in Brazil at the Saõ Bento Mine where a pressure oxidation circuit is used to treat the refractory flotation concentrate. This plant has confirmed the viability of combining bio-oxidation with pressure oxidation as a cost-effective method ofincreasing capacity at an existing oxidation plant.??Wiluna, Australia. The plant at Wiluna Gold Mine, Western Australia, was commissioned in 1993. Although originally designed to treat 115 tonnes per day of concentrate this has subsequently been increased to 158.??Other plants at Tamboraque in Peru, Harbour Lights and at Youanami in Australia have been commissioned recently."

Jan 1, 2012

By C. Liu

Corrosion behavior of the stir zone in a friction stir weld of dissimilar A12024/AZ31 alloys was investigated in the immersion test in distilled water (pH=6) for different times. Microstructures and the distribution of chemical elements were analyzed by scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). Due to the difference in the corrosion potentials between A12024 and AZ31, the AZ31 alloy constituent in the stir zone was susceptible to the corrosion attack in the distilled water. The corrosion attack was found to occur in the narrow region of the AZ31 alloy adjoining the A12024 region, where there was a low ratio of anode-to-cathode surface area. The corrosion attack became more severe in the AZ31 alloy regions with increasing immersion time. The A12024 alloy region in the stir zone of the weld was protected by cathodic reactivity due to sacrificial anode AZ31 alloy.

Jan 1, 2007

By A. J. Neale, B. C. Flintoff

"In most mineral processing operations the term audit is usually reserved for the exercise of checking financial records and/ or safety practices. While these activities are time consuming, no one disputes their necessity or value. If we subject these areas to such careful scrutiny, why is it that we don't normally apply the same principles to critically examine process operation. After all, the operating efficiency of the plant impacts directly on the measures of profitability.A mineral processing plant is a complex system that has a number of distinct, but mutually dependent elements: process equipment, instrumentation, operating policies, maintenance policies, control strategies and people. To ensure maximum economic performance, in the dynamic environment that characterizes a concentrator, requires a periodic review of each of these areas. However, to be useful, the study must be based on sound metallurgical principles and be conducted in a highly focused manner. Experience teaches us that the exercise is very revealing and potentially very rewarding.This paper will discuss the process audit process and illustrate its potential value through illustration taken from plant studies.IntroductionThe last twenty years have seen tremendous technological and organizational changes sweep the minerals industry. Process control systems, on-stream analyzers, and gold recovery techniques barely conceived twenty years ago are now incorporated in virtually all new installations in an effort to maximize operating efficiencies. In conjunction with these developments, changes in the way plants are managed, down-sizing of technical staff, reduction in the size of operating crews, and the flattening out of the management structure have significantly reduced operating costs. As a result, plants are making more efficient use of our natural resources, minimizing the costs of production, and in turn maximizing operating profits. Or are they?"

Jan 1, 1991

By J. Schick, V. Granger

Nowadays, all French former uranium mining sites are remediated and redeveloped. If needed, mining waters containing radium have to be treated before discharged into the environment. Classical radium treatment consists in a (Ba,Ra)SO4 salt precipitation and radium monitoring was carried out using a time-consuming analysis called emanometry. Three zeolite samples have been tested to remove 226Ra from mining water. In batch experiment, radium was totally (R=100%) and quickly removed after 2 minutes contact time. Continuous sorption experiments were carried out through a vertical column at lab scale. Chabazite is the most efficient zeolite with an 226Ra activity below 0.2 Bq/L until 60000 Bed Volume. Chabazite is always efficient although radium content in material reaches 150 Bq/g. 226Ra uptake was also tested at semi-industrial scale on a pilot plant. More than 3000 m3 were successfully treated with a radium content below 0.1 Bq/L. The environmental impact assessment of Ra-chabazite was characterized by using batch leaching tests made according to the NF EN 12457-2 standard as applied on all wastes. Ra-chabazite stability is excellent during this test: radium leaching is very low, less than 0.005%. A new 226Ra measurement method was developed by ICP-MS for a better analysis reactivity. This new method was carried out in a couple of minutes with a lower sample volume than emanometry. The validation was performed according to the French NF T90-210 standard for the calibration function definition, the limit of quantification, the accuracy and the interferences.

Jan 1, 2020

By M. M. Papic

"This paper describes the Sasol coal liquefaction process, as used in South Africa. It covers coal supply, coal gasification, gas purification, Fischer-Tropsch synthesis, the major utility systems involved and the economics of the process.IntroductionThe Sasol coal liquefaction process is based on Fischer-Tropsch synthesis of liquid fuels from carbon monoxide and hydrogen, which are in turn obtained by gasification of coal with steam and oxygen. The process is shown schematically in Figure I.The first step in the process is coal preparation, in which the coal is crushed and screened to a 3-50 mm size for gasification on one side and to -3 mm size for steam and power production on the other. Oxygen needed for coal gasificatoin is produced in the air separation plant.Coal is gasified under pressure by steam and oxygen in the Lurgi gasification plant, where raw, impure gas is produced . The raw gas is first washed in a scrubber with a circulating gas liquor, heat is then recovered from it in a waste heat recovery boiler and the gas is further cooled for purification. Water-insoluble materials (tar oils) in the gas liquor are separated from aqueous solution and sent to tar refining for the recovery of tar products. The aqueous portion of the gas liquor goes to a Phenosolvan solvent extraction process, where phenols and ammonia are recovered. Water then proceeds to the effluent treatment plant.The scrubbed and cooled raw gas goes to a Rectisol gas purification plant, where all components other than hydrogen, carbon monoxide and methane are removed as completely as possible by absorption in refrigerated methanol. The acid gases (CO2, H2S) stripped from the methanol in the Rectisol unit are processed in a Stretford plant for recovery of sulphur. Regenerated methanol is returned to the process. The purified synthesis gas is passed to the fluidized-bed Synthol reactors, where Fischer-Tropsch synthesis reactions take place.The synthesis products are recovered in a product recovery unit as separate streams of decant oil containing higher-molecular- weight hydrocarbons, light oil comprised of lower-molecular- weight species, the aqueous stream containing water solubles, a C3/C4 stream, a C2 stream , a methane stream and a hydrogen-rich stream. Most of the hydrogen is recycled to the Synthol reactors; a major portion of the methane is reformed to hydrogen and carbon monoxide for recycle; the C2 fraction goes to an ethylene plant; and liquid streams proceed to the product refinery.The product refinery is used to upgrade and purify the Synthol products to specification fuels and chemicals.Sasol l, the first coal liquefaction plant in South Africa , was built in 1955. It is still operating and has a product output of about half a million tonnes per year. The Sasol II plant is in a commissioning stage and will be in full operation in 1981. It is about five times the size of Sasoll. It uses over 12 million tonnes of coal and produces more than 2 million tonnes of saleable products annually (1,2,3). The Sasol llI plant, which is a mirror image of Sasol II, is under construction and scheduled for completion in 1983."

Jan 1, 1981

By Wignall. T. K., J. De Geoffroy

Statistical models are fitted to the observed distributions of eighteen characteristics of the population of commercial porphyry deposits of North and South America. The statistical base required for the formulation of the statistical models includes 58 commercial porphyry-copper-molybdenum deposits of the Cordilleran Belt from which geological, geometric and economic data were collected. Predictive and composite models are derived from the statistical study to assist explorat10n. planning, engineering studies and fmanc1al analyses as required for the development of new porphyry deposits in the Cordilleran Belt.

Jan 1, 1973

By A. Warczok, T. A. Utigard

"Slags from smelting of copper concentrates contains from 1 to 15% of copper. Copper is present in the form of copper or copper matte inclusions of size from 2 to 1000 micro, and as dissolved cuprous oxide. Removal of the copper requires the slag reduction, primarily reduction of magnetite and co-reduction of cuprous oxide. Thus, the kinetics of the slag reduction play an important role in copper recovery. Instantaneously, at the contact of carbon and a slag the gaseous film is formed. The magnetite and cuprous oxide reduction is going through a gaseous film, separating the slag and carbon of a coke or electrodes. The thickness of a gaseous film grows to a critical value and gas bubbles, containing CO and CO2, are created and rise up in the slag. Results of measurements of kinetic of the slag reduction with graphite showed high value of activation energy, close to the value of activation energy of Boudouard reaction. Strong temperature dependence of the reaction rate points out the thermal instability of the reacting system. It was found that the slowest process in the reduction stages determines the loop of CO and CO2 transfer and magnetite diffusion to the slag/gas film boundary. Strongly endothermic Boudouard reaction seems to cause thermal instability on the reaction surface. So, heat transfer to the reaction surface is very important. Due to low thermal conductivity of a slag the convection dominates in the heat transfer. So, any slag stirring accelerates the rate of reduction and coalescence of metallic copper or copper matte inclusions."

Jan 1, 2015

On the 26th of June 2000 a hydraulic fill retaining barricade failed at the Bronzewing mine in Western Australia. The barricade failure resulted in the release of 19,000 m3 of saturated hydraulic fill into the mine and caused the deaths of three miners. Following this tragic accident, the practices and procedures of mines using hydraulic fills came under intense scrutiny by regulatory bodies and mining companies. At this time, the use of hydraulic fill at Normandy?s zinc/copper Scuddles mine was suspended and waste rock became the sole backfill material in use underground. By 2003, development of the adjacent Gossan Hill mine had progressed to a point where a self supporting fill material was required to enable full recovery of high grade ore. Cemented hydraulic fill (CHF) was identified as the optimal fill type and work began on designing appropriate management procedures and controls to ensure the safe implementation. This work included definition of the fill properties, plant design and construction, reticulation system design, design of stope barricades and drainage systems and fill placement control and monitoring practices. CHF placement began on 16th July 2004 and has continued to date. Significant operational experience has since been gained in areas including plant performance, fill product quality assurance, barricade construction, stope drainage and in-situ performance.

May 1, 2007

By W. H. Mathews

"The Hardie group of cinnabar claims is in the interior of British Columbia; 25 miles northwest of the city of Kamloops. It is one of a number of mercury; properties scattered along a north trending belt 20 miles long and up to 5; miles wide. In all but one of these properties cinnabar is associated with; dolomite veinlets in zones of carbonate alteration in bedded rocks of Triassic; and Cretaceous (?) age; or in intrusives cutting these bedded rocks. No dolomite alteration or cinnabar mineralization is known in the undoubted Tertiary rocks adjacent to the mercury belt.The mercury showings of the Hardie group lie for the most part in a granitic stock cutting Cretaceous (?) volcanics. The rock in this intrusive shows marked variations in texture and has been described in earlier reports as granite and granodiorice, granite porphyry, and trachyte or dacite porphyry. At Hardie mountain the cinnabar mineralization, unlike that of the other properties, is associated with a fine-grained, almost chalcedoni c, quartz; carbonates, though present, are of minor importance. Some of the most interesting showings are found in an adit in the southeastern part of the property where cinnabar mineralization shows a very distinct structural but not a genetic relationship to a brown porphyry dyke 2 to 8 feet wide cutting a phase of the stock that may best be described as aplitic"

Jan 1, 1954

By Brooke Clements

The Buffalo Head Hills region is located approximately 350 kilometres northwest of the city of Edmonton in northcentral Alberta (Figure 1). The Alberta diamond joint venture consisting of Ashton Mining of Canada Inc., Alberta Energy Company Ltd and Pure Gold Minerals Inc. began exploring for kimberlites in the Buffalo Head Hills region in late 1996. At the time, the Mountain Lake diatreme, located 200 kilometres to the southwest, was the only reported kimberlitic rock in Alberta (Leckie et al., 1997, Figure 1). Exploration efforts since 1996 have successfully identified a new diamondiferous kimberlite province in Canada.

May 1, 2001

By Judy K. Todd

Double benching has been utilized as an excavation technique in open pit mines for many years. This process involves drilling, blasting, and excavating the material for the design bench height. A second bench is then excavated without the creation of a catch bench, i.e. only minimal offset from the first bench face is allowed when drilling off the second bench. The result is a double high bench face or double bench. When drilling off the second bench, the offset of the drill from the bench face projects the lower bench face into the pit up to an extra five meters. This reduces the maximum attainable bench angle, enhances the probability of rock escaping the catch bench and increases the overall strip ratio. The generally utilized process of trim blasting also can impact on the final bench profile by contributing to blast damage of the face. BHP Billiton Diamonds Inc., Ekati Mine Diamond MineTM, has pioneered the usage of a technique that eliminates this offset. Double benching is accomplished by drilling a single, 30m pre-shear (two 15m benches) to define and protect the final bench profile. This article provides a comparison of the attained face angles obtained in the field utilizing both of the above methods, as well as a comparison with the analytically predicted angles prior to excavation.

May 1, 2002

By H. Fujiwara, T. Ito, T. Mizuguchi, K. Kawasaki

"In this study, we characterize the high-temperature deformation of typical “Class I” solid solution Al-Mg alloys as a superplastic elongation attributable to the solute drag creep of dislocations. The second-phase particles formed by adding Fe or Si as impurity atoms to the Al-Mg alloys impeded the gliding motion of dislocations, thereby decreasing their hot ductility and resulting in cavity formation. High-temperature tensile tests were performed with initial strain rates in the range of 1×10–3 to 1×10–1 s–1 at air temperatures 673–723 K. The dominant high-temperature deformation mechanism in these alloys was the solute drag creep controlled by the interdiffusion of Mg in Al. In this study, the calculation of critical length, defined by the diffusion-based relaxation of the stress concentration region around second-phase particles, is reported using the Needleman–Rice parameter. An analysis of the impact of cavity formation based on a comparison of the Needleman–Rice parameter and second-phase particle size is also reported.INTRODUCTION Aluminum alloys with high specific strengths are utilized as structural materials for transportation machines to minimize their weight, which consequently maximizes fuel efficiency, environment preservation, and so on (Miller et al., 2000; Heinz et al., 2000; Starke & Staley, 1996; Polmear, 1996; Immarigeon et al., 1995; Burger, Gupta, Jeffrey, & Lloyd, 1995; Ye, 2003). Microstructure refinement by severe plastic deformation (SPD) has been performed on a laboratory scale to achieve a higher strength of crystalline materials (Valiev et al., 2006; Song, Ponge, Raabe, Speer, & Matlock, 2006; Beyerlein & Toth, 2009; Sabirov, Murashkin, & Valiev, 2013; Sauvage, Wilde, Divinski, Horita, & Valiev, 2012). At room temperature, grain refinement strengthens the material, as given by the Hall-Petch relationship (Hall, 1951; Petch, 1953); at higher temperatures, superplasticity can be expected (Sherby & Wadsworth, 1989; Edington, Melton, & Cutler, 1979; Furukawa, Horita, Nemoto, & Langdon, 2001; Langdon, 2006). However, the synthesis of large-size materials by SPD processes is not yet feasible."

Jan 1, 2018