Search Documents

By I. G. L. Sinclair

"ABSTRACTTill geochemistry was the principal exploration tool employed by Selco in the investigation of a zinc prospect in Lanark Township, Ontario. The geochemical studies were undertaken after the discovery at surface of marble boulders containing bands of sphalerite and lesser amounts of galena.The source of these mineralized boulders was sought by means of B-horizon soil geochemistry, followed, where appropriate, by back-hoe trenching and till sampling. The thickness of the tiff in this part of Ontario seldom exceeds 3 m or 4 m and it was generally possible to sample complete profiles of the till and thus to obtain detailed information concerning the dispersion of zinc. Drilling and trenching at the up-ice extremity of the zinc dispersion trains showed the source of the float to be sub-economic bands of sphalerite in the Grenville marble. IntroductionTill geochemistry was used extensively by Selco during the period 1975 through 1980. It was the principal exploration technique employed in a program seeking carbonate-hosted lead-zinc deposits of the Balmat-Edwards type in the Grenville rocks of southeastern Ontario. This paper describes the use of the method to locate the bedrock source of a group of sphalerite boulders found at the surface near the village of Hopetown in Lanark Township (Fig. I) . Geochemical investigations at this locality were the subject of a previous publication by the author (Sinclair, 1979).All of the analytical work related to this project was done by Bondar-Clegg & Co. Ltd. in their Ottawa laboratory. In all cases the -80 mesh fraction of the till was analyzed. The total zinc content was determined by atomic ab sorption spectrometry after hot aqua regia digestion; readily extractable zinc was determined by atomic absorption after samples had been cold-leached for 18 hours in an ammonium citrate hydroxylamine hydrochloride solution, the pH of which was adjusted to 8.5"

Jan 1, 1986

By A. Mazhary

"Although ore sorting in mining is not a new concept, sensor-based sorting has failed to gain broad acceptance due to perceived challenges with the technology. In order to gain wider applications, this research focuses on treating waste rock and low-grade ore to identify and test appropriate sensors and to evaluate the response. Results showed that amenability of rocks to sensor-based ore sorting is both sensor and ore specific. It was also observed that the efficiency (recovery) of sorting is directly influenced by the degree of heterogeneity of the rocks. The overall outcome showed that with the right sensor, several of the materials tested are amenable to sensor-based ore sorting. Mining companies could benefit from multiple economic and design impacts, such as lower energy cost, lower transportation costs, higher metal recoveries and smaller footprints that lead to more sustainable mining. This paper will focus on the effects of heterogeneity of rocks on sorting potential and efficiency.IntroductionSensor-based ore sorting has been attracting more attention since the pressure for effective resource extraction and management has increased. An urge to make most of the current deposits, and to make the low-grade deposits economic to mine has ushered the technology to find new ways to overcome the new challenges. No matter the terminology used, such as coarse beneificiation, waste rejection, particle or bulk sorting, the purpose of sensor-based ore sorting is to remove low-grade rocks before the comminution circuit, increasing the feed head grade and quality while reducing the energy costs related to comminution.Despite nominal advantages, there have always been some concerns that have impeded the intorduction and acceptance of the technology. One of the most important shortcomings of ore sorting is their capability, or capacity, to keep up with the high-tonnage mining. Some other issues that have been mentioned as drawbacks to sorting include installation cost of such devices, feed preparation for effiecient sorting along with accuracy of sorting and probability of false negatives (Manouchehri, 2003)."

Jan 1, 2015

By Colin Jones

Canadian Clay Products Inc., which mines bentonite in Saskatchewan near Truax and operates a plant at Wilcox, is the sole producer of swelling bentonite, often called western bentonite, in Canada. Seven products produced by the company are used in binders, sealants, water and waste water treatment, plasticizing agents, foundries and absorbents. Reserves are reported at about one million tonnes for the deposit but the area in general contains significant additional reserves.

Jan 1, 2001

By Peter Wells, Laxman M. Amaratuga, Todd M. Kanhai

"Certain mining methods (eg. Cut-and-fill) result in the contamination of run-of-mine ore with shotcrete. This shotcrete remains mixed with the ore throughout processing. Experimentation performed by Falconbridge Limited revealed that underground contamination of ore by shotcrete (eg. as little as 1% by weight) has led to ill-effects on the nickel recoveries from the flotation process in the mill. The nickel recoveries of contaminated samples were lower than tests without the shotcrete Contamination.To optimize flotation circuits it is important to know why the contamination has created these effects and also to find a method to abate or remove them. Laboratory testing showed that the age of the shotcrete was a factor in it’s effect on nickel recoveries. Younger aged shotcrete gave nickel recoveries lower than baseline nickel recoveries with no contamination. Older shotcrete gave nickel recoveries similar to the baseline.Literature on other cementitious material contaminations on ore revealed that a possible means of remediating this problem is the use of acid in the flotation. The initial pH in the flotation pulp was designed to be pH 9.2, but with the young shotcrete contamination the pH was in the neighbourhood of 10.5. Acid addition may act as a means of lowering the pH to the optimal operational value. Laboratory test work showed that acid addition brought nickel recoveries closer to the baseline."

Jan 1, 2000

By Tim Hughes, Steve Gannon, Jennifer Abols

"In the past year, two very innovative gold ore processing plants have been designed, built and commissioned by Gekko Systems Pty Ltd. The first plant in Vietnam utilizes conventional crushing and ball milling followed by gravity concentration (Inline Pressure Jig (IPJ) and Falcon concentrator), flotation, intensive leaching (GFIL), the first industrial scale use of AuRIX®1001 ion exchange resin and a cyanide destruction circuit. The second plant, in Australia, uses a 3 stage crushing circuit to crush the gold ore to minus 1mm, followed by gravity concentration utilising a rougher, scavenger, cleaner circuit of IPJ’s and a Falcon concentrator. A direct smeltable gold concentrate is produced as well as a lower grade concentrate for future intensive leaching or sale. Both plants were designed and built within very tight time frames and budgetary constraints. The experience gained during the plants’ design, commissioning and operation are discussed.INTRODUCTIONGekko Systems (Gekko) is a leader in the development of innovative technology for gravity recovery and intensive cyanidation. It provides low cost and metallurgically optimal solutions for its customers. It has also led the trend away from whole ore cyanidation (CIP/CIL) towards gravity/intensive cyanidation (GIL) and gravity/flotation/intensive cyanidation (GFIL) plants. These types of plants offer low capital costs, low environmental impact and maximum return to investors (Rob J Longley et al, 2002). Key to this type of flowsheet is the application of a continuous concentrate unit, such as the InLine Pressure Jig (IPJ), which is designed to produce high gold gravity recoveries at a coarse grind (Sandy Gray, 2003). When combined with other gravity devices, and/or flotation, and intensive cyanidation, using the Gekko InLine Leach Reactor (ILR), very high overall recoveries can be achieved.In 2004, Gekko launched a new range of products called Gekko Modular Systems. The idea was to provide off the shelf, complete solutions for the separation and recovery of complex and free gold as well as the pre-concentration of diamonds. A series of modules were designed that incorporated Gekko manufactured as well as outsourced equipment. Gekko now offers modules ranging from feeding and conveying to crushing, gravity recovery, flotation, intensive cyanidation, refining and detox (see Figure 1)."

Jan 1, 2007

By Sabine Noelte, Mikko Petteri Rantamäki, Christopher Robben, Anssi Takala, Karl-Erik Rånman

"Sensor-based ore sorting is on its way to establish as a standard option for physical separation. The increasing number of installations in coal, iron ore, industrial minerals and hard-rock metal mining segments underlines the technological and financial potential that is beginning to be untapped. The Ma’aden Phosphate installation with 1.650 t/h sensor-based ore sorter feed sets a new benchmark for the possible capacity of stationary installations. Besides stationary installations, including multiple sorters parallel in different size ranges and multiple stages, containerised semi-mobile plants are applied. These offer two advantages, first being the reduction of transport costs when applied close to the mining face. The second is that semi-mobile systems enable processing of tens of thousands of tonnes of ore in a piloting phase with an approximate duration of 0.5 to six months, verifying the results laboratory mini-bulk tests on 5–10 tonnes of sample. This is especially important for low-grade metal ores because of the inherent Fundamental Sampling Error, as well as the Grouping and Segregation Error. The paper elaborates the results achieved within the I2MINE project, treating polymetallic ore at the Boliden Concentrator in Sweden.INTRODUCTIONSensor-based ore sorting (SBS) is becoming a standard option for physical separation, applied in all segments of mineral production. The Umm Wu’al project sets the bar for stationary SBS installations with 1,650 t/h feed (TOMRA, 2015). TOMRA Sorting Solutions has finalised an agreement in cooperation with Outotec to supply Outotec-branded sorting solutions for the mining and metallurgical industry (TOMRA, 2014). Especially for low-grade hard rock metal ores, an interdisciplinary approach is necessary applying experts for all aspects of mineral production. Due to the impact on the whole process stream, it is important on the end user side to have high level managerial support and involve all disciplines to ensure that all stake holders are involved in the analysis."

Jan 1, 2016

By C. R. Edwards

"Equity Silver Mines Limited, Canada's largest silver mine, has designed, built and operated a leach plant to reduce the levels of antimony and arsenic in its silver-gold-copper flotation concentrate. The orebody contained deleterious antimony and arsenic minerals in such proportions that the economic long-term sales contracts necessary to obtain project financing could not be procured. Construction of the leach plant therefore allowed development of the mine to proceed. Although the plant took some time to reach design throughput and product specifications, due to the complex and unique nature of the operation, these goals were successfully met and surpassed. This paper describes the physical plant and/or process technology modifications made to mold the main processes-concentrate leaching and filtering, autoclaving and filtration of by-products, and crystallization of salt cake-into an effective, economic operation.IntroductionEquity Silver Mines Limited, a member of the Placer Development Group, owns and operates an open-pit silver mine and related facilities located 37 kilometres southeast of Houston in north-central British Columbia. The mine occupies a 44 I-hectare (1089 acre) site at an elevation of 1300 metres (4265 feet) on the Nechako Plateau. Producing a copper concentrate containing high values of silver and gold, it is the largest silver mine in Canada and one of the largest in the western world. Equity stresses open communications, positive motivation, and production with safety, and achieved the best mine safety record in western Canada in 1984."

Jan 1, 1985

By R. N. Murarka

"Hydrocyclone modelling and selection procedure is illustrated. Computerized procedure for hydrocyclone cut size determination for grinding and non-grinding applications is described.A standard procedure for evaluating operating hydrocyclones is described in detail. Many case studies are illustrated comparing actual plant performance with the computer simulation output in terms of overflow product size distributions.INTRODUCTION Cyclones are widely used for applications such as: close circuit grinding, backfill, tailings and dewatering. Normally, cyclones are used for very fine separations where screens are not suitable or too expensive. Figure 1 shows the separation size range of various classifying devices. Cyclones are popular because of their low capital and operating cost. Cyclone selection procedure for different applications depends on the amount of information available on the cyclone feed slurry characteristics. Closed circuit grinding applications will be discussed in detail in this paper. The Cut Size:The size of the material in the feed which reports 50% to each product stream (i.e. underflow and overflow), after correcting for the feed solids by-passing with the underflow liquid, is termed the cut size or ""d50c"". This is often used as the criterion and the basis for cyclone design.When the corrected recovery to underflow of each mesh size in the feed is plotted against the geometric mean size in microns on a log scale, the micron size corresponding to 50% recovery is the d50c size."

Jan 1, 1992

By Anna M. Ferrero

Stability condition of underground excavations have to be assessed to guarantee safe operations within the quarrying working areas. This objective requires a reliable assessment of the rock mass natural state of stress and of the stress redistribution induced by the excavations. This goal is often complicated by difficult geological conditions induced by tectonic stresses, complex topographies and large and irregular excavation geometries. Consequently, the acting state of stress needs to be measured by specific in situ measurement devices. This work refers on an in situ measurements campaign carried out by CSIRO tests in an underground quarry located in the Carrara marble basin. The difficult path carried out for interpretation of the measurements is described in this paper. In particular, the numerical modeling performed using the Boundary Element Method (BEM) first, to study the influence of both surface topography and excavation geometry and then the Distinct Element Method (DEM) to evaluate the influence of rock discontinuities in the measurement zone are illustrated in this work. Parametrical analysis of the rock mass mechanical features is also described in order to calibrate the numerical models and analyze the experimental results. The work has been carried out trough several phases, which are: characterization of the rock mass through geostructural surveys: this allowed us to classify the rock mass and determine the mechanical and physical parameters necessary for modeling; on-site measurement of stress levels through the application of over coring techniques; numerical analyses for the simulation of excavation phases, using the Examine3D (BEM) engineering analysis code. comparison between the measured stress levels and those numerically calculated and subsequent calibration of the BEM model; Numerical model of the forecasted excavation based on the calibrated (BEM) model.

May 1, 2009

By Kevin B. Doyle

"Canada now supplies 23 per cent of the world demand for potash. Although potash is produced by many countries, Russia and Canada have the greatest reserves and capability to supply the future substantial demand over the next decade. It is estimated that demand will grow from 38,000,000 mt KCl in 1975-76 to 60,000,000 mt KCl in 1985-86. Current firm expansion plans and development underway in the world will move Russia to the forefront in supplying this demand growth. Russia will move from supplying 40 per cent of world demand in 1975 to supplying as much as 52 per cent in 1981. Canadian deposits suffer from natural disadvantages, such as high costs and risks of mine development and operation, and high-cost transportation to international markets, but experience has shown that these natural barriers can be surmounted to effectively compete in these international markets. However, Canadian potash is losing out in the race to supply the growth in the world potash demand over the next ten years because of artificial barriers raised through the unhealthy environment created by the current battle between different levels of government and the industry over resource taxation and legislation."

Jan 1, 1976

By Michael L. Free, Zongliang Zhang, Joshua M. Werner

In the copper electrowinning process, short-circuiting between the anodes and the cathodes is a critical problem that changes the current allocation among local electrodes and reduces the current efficiency significantly. Possible reasons for the short-circuiting include the improper alignment of the electrode, bent electrode, and nodules on the cathode surface. In typical tankhouses, there is often a time between shorting and harvesting as well as between shorting and clearing. Therefore, it is inevitable to have short-circuiting affect the operation performance in practical electrowinning operations. However, one key piece of missing data is the actual measurements of the current efficiency as short-circuiting is approached and allowed to continue. Consequently, short-circuiting tests that allow tracking of electrowinning parameters before and after short-circuiting were performed in a laboratory scale Cu electrowinning cell. In the tests, the electrode spacing change, the mass of electrodeposited Cu, the deposition morphology, and the current allocation as well as the current efficiency before and after short-circuiting were studied. Results show that the short- circuiting affects the current allocation and the current efficiency significantly. Moreover, it changes the Cu deposition on the short-circuited cathode and therefore causes problems for Cu electrowinning. INTRODUCTION Electrowinning (EW) is commonly used for copper production around the world, with a rated production from 120,000 to 200,000 tons per year per operation (Wiechmann, Aqueveque, Henríquez, Muñoz, & Morales, 2014). In Cu electrowinning, Cu ions in the electrolyte are reduced on the cathode surface as metallic copper with a DC current, while on the anode, a counter anodic reaction occurs with oxygen gas generation (Werner, Zeng, Free, Zhang, & Cho, 2018; Zhang, Werner, & Free, 2018; Zhang, Werner, & Free, 2018). In copper electrowinning, an average current density of 200 to 400 A/m2 is applied to the electrowinning cell (Wiechmann et al., 2014). As the Cu deposits on the cathode, the distance between anode and cathode reduces and most of the time, short-circuiting forms between some anodes and cathodes in a large tankhouse containing thousands of electrodes, reducing the current efficiency and increasing the energy consumption significantly. The current efficiency in well-run copper EW operations is typically above 90 %. Most of the unused current is wasted through short circuits, stray currents, and by-byproduct formation (Davenport, King, Schlesinger, & Biswas, 2002; Wiechmann, Vidal, Pagliero, & Gonzalez, 2002; Wiechmann, Morales, & Aqueveque, 2010). Usually, in the tankhouse, the short-circuiting increases the current in the involved cathode by up to 1500 A (Wiechmann et al., 2010). Multiple reasons can cause the short-circuiting in the cell, and the most common reasons include the uneven current distribution among cathodes, tilted electrodes, bent electrodes, and nodules formed due to the large deposition roughness. Recognition of this challenge in the Cu electrowinning process has led researchers to perform many investigations on approaches to avoid and reduce the short-circuiting in the cell. A series of research investigations have been conducted to develop and improve a new type of intercell bar for Cu electrowinning (Wiechmann et al., 2002; Wiechmann, Morales, Aqueveque, & Burgos, 2007; Wiechmann, Morales, & Aqueveque, 2009; Wiechmann et al., 2010; Wiechmann et al., 2014). The associated test results show that this new design limits the occurrence and magnitude of short circuits and allows operation at higher current densities. Sandoval, Clayton, Dominguez, Unger, and Robinson (2010) stated several keys to control short circuits, such as maintaining the straightness of the cathode, removing “edge hair” from the cathode starter, and maintaining electrode alignment in the cell. Prengaman and Siegmund (1999) from RSR technologies developed a new Pb-Ca-Sn anode to prevent the anode deformation, thereby reducing the short-circuiting in the Cu electrowinning cell. Although the negative effects of short-circuiting on the Cu electrowinning have been recognized, and various investigations have been conducted to address this issue, the actual measurements of the electrowinning behavior and performance as short-circuiting is approached and allowed to continue are seldom reported. However, in typical tankhouses, there is a time between when shorting occurs and harvesting/clearing are performed. One key factor in determining the harvest time is the frequency of shorting. Consequently, we have performed short-circuiting tests that allow us to track electrowinning parameters before and after short-circuiting.

Jan 1, 2019

By Mika Muinonen

"Dewatering of nickel concentrate at the INCO Thompson integrated mine-metallurgical site takes place within the smelter plant. The eight original 60 foot diameter cable torque thickeners of which four were operational and eight Dorrco internal drum filters have been replaced with a single Outokumpu high rate thickener and a single Lasta pressure filter. The modernization has resulted in a filter cake which has a more stable and lower moisture content. Control of the entire dewatering process has been improved and costs have been reduced.Typical filter cake produced from the Dorrco filters during processing of high tonnages of Birchtree mine ore was ~20% moisture vs. ~13% moisture for concentrate produced from the Thompson mine ore. The high moistures were correlated with the amount of fine magnesium silicate gangue in the concentrate. As Birchtree ore processing rates have increased, this filter cake moisture became unacceptable because of material handling problems and the impact on furnace metallurgy. The Dorrco filters were replaced with the Lasta filter in 2003 that has consistently produced filter cake at ~11% moisture.This paper summarizes the piloting, design, installation and commissioning of the modernized dewatering circuit.INTRODUCTIONThe Thompson integrated nickel processing facility was built in 1958 and originally consisted of a mine-mill-smelter and, soon after, a refinery.Nickel concentrate is pumped from the mill as a dilute slurry directly to the smelter facility ~200 meters along an unheated pipe trestle. Originally, nickel concentrate was de-watered using up to 8 conventional 60-foot diameter thickeners and 8 internal vacuum drum filters."

Jan 1, 2006

By C. A. Young, H-H. Huang, L. G. Twidwell

Equilibrium calculational software programs can be effectively utilized to model important parameters in aqueous and aqueous/solid systems, e.g., activity or concentration, solubility, temperature, solution pH, solution potential, and ligand complexation. In this regard, the calculational program ST ABCAL will be demonstrated. Illustrative examples for the creation of diagrams such as potential-pH, and activity or concentration-pH will be presented to demonstrate the fundamentals in real hydrometallurgical systems. Speciation, titration and mixing will be used to simulate or predict operational processes. Berkeley Pit water from a flooded abandoned copper open-pit mine will be used to illustrate the modeling process. According to analytical results the water contains about 20 important constituents. In addition to measured potential and dissolved oxygen, there are two distinctive oxidation/reduction couples. Concentration and other experimental parameters are seldom matched to each other and 12 different conditions have been identified. Water for each condition must be speciated in order to find the best-fit model. The STABCAL program will be used for the modeling calculations and the implication of the water chemistry to defining treatment opportunities will be discussed.

Jan 1, 2005

By Ahmad Ghahreman, Denver Cowan, Yeonuk Choi

"Testwork was conducted in order to compare the effectiveness of carbon based catalysts while oxidizing a gold-bearing pyrite concentrate under atmospheric conditions. Without the use of a catalyst the oxidation of pyrite was incomplete after 96 hours, resulting in roughly 60% pyrite oxidation. Furthermore the resulting sulphate yield from unassisted pyrite oxidation ranged between 72 and 84%. It is evident that atmospheric oxidation of pyrite is not viable due to slow oxidation kinetics and high sulphuric acid production when using a ferric sulphate media without a catalyst. The effect of two different carbon based catalysts, one Lewatit® AF 5 a new microporous carbonaceous bead, and the second a granular coconut shell based activated carbon, were tested under the same oxidation conditions as the unassisted pyrite tests. After 96 hours, Lewatit® AF 5 assisted oxidation showed approximately 96% pyrite oxidation with a sulphate yield ranging between 26 and 35%, while the activated carbon assisted oxidation reached approximately 100% pyrite oxidation with a sulphate yield between 36 and 37%. Testwork indicated that not only does the addition of a carbon based catalyst greatly improve the oxidation kinetics and lead to almost complete oxidation, the sulphate yield is also drastically reduced, resulting in very high elemental sulphur yields.INTRODUCTION Pyrite is an important sulphide mineral due to its ability to contain invisible gold concentrations up to 132 g/t (Chryssoulis & Cabri, 1990). As a result, ores composed of only a small amount of pyrite still have the ability to contain high gold grades. This refractory gold cannot be accessed via conventional gold leaching processes, such as cyanidation, and additional oxidative pre-treatment is required to liberate the gold, making it more amenable to extraction (Marsden & House, 2006). Current oxidative pre-treatments do exist consisting of both pyrometallurgical and hydrometallurgical processes including high temperature and high pressure leaching within autoclaves, biological atmospheric leaching and roasting. Autoclaves are a proven process reaching desirable recoveries within approximately a 1–2 hour retention time, due to the increased temperatures and pressures, allowing for an increase in dissolved oxygen (Marsden & House, 2006). The typical reaction for pyrite oxidation within autoclaves is presented in Equations 1, 2 and 3."

Jan 1, 2017

By Richard C. Banting

Excessive vibration is known to have an adverse affect on soft body tissue and operators of heavy mining equipment can be exposed to vibration that exceeds levels recommended in international guidelines (ISO 2631-1, for example). Research has found that many of the seat and suspension systems currently used in mine haul trucks and load haul dump vehicles are actually amplifying the vibration. This overview presentation will outline the current research being conducted at Laurentian University and the University of Western Ontario, and the roles of partners in rating the ability of a number of commonly used mine vehicle seats to isolate harmful vibration.

Oct 1, 2010

By A. Giacomini, M. Nazem, E. Fathi Salmi

"Numerical simulation of collapse of tunnels in weak rocks is one of the challenging problems in rock mechanics. Collapse can impose technical and financial difficulties during the construction of underground excavations. This phenomenon, particularly in shallow excavations, may lead to propagation of a caved zone toward the surface and formation of chimney subsidence. Chimney subsidence has numerous catastrophic consequences such as the adverse environmental impacts and damage to surface structures in vicinity of excavations. Due to the importance of subsidence in civil engineering, the main goal of this study is to propose an appropriate method for preventing the formation of subsidence in shallow tunnels in weak rocks. The Dolaei road tunnel is investigated as a case study, where a large chimney subsidence has occurred. The geology of the area and the geostructural characteristics of the rock mass surrounding the tunnel are briefly reviewed in this paper. Two-dimensional as well as threedimensional numerical simulations are conducted to study the tunnel stability. Moreover, the effects of staged excavation and pre-supporting method on controlling the ground movements are studied. Outcomes of this study indicate that employing forepoling and staged excavation can be a practical remedy to control the ground movements and prevent the formation of chimney subsidence.INTRODUCTIONPredicting the formation of subsidence, mainly sinkhole subsidence over civil or mining excavations, is a very challenging task. An accurate prediction of subsidence is required for selecting an appropriate control and mitigation system to reduce the level of ground movements and its impact on the surface life (Bétournay et al. 1994; Leca and New 2007). Excavations, particularly in weak grounds, could result in surface subsidence; they modify the in-situ stress conditions as well as the hydrogeology of the area. Construction of unsupported excavations in soft soils and relatively weak rocks usually leads to the formation of a failure zone behind the face. In a very soft ground, the failure zone can extend towards the ground ahead of the tunnel face. Propagation of this zone toward the ground surface results in generation of sinkholes."

Jan 1, 2015

By Szilvia Szabo, Jozsef Paulovics, Ljudmilla Bokanyi

"Waste recycling is one of the most important challenges of the XXI century. The recycling of wastes is closely related to and bases on the mineral processing. Many mineral processing techniques and equipment are applied in this field. The principles of the characterisation of wastes and design of technologies is rather similar to the classic mineral processing. Nevertheless, the diversity of the wastes and their complex composition and properties, as well as their environmental impact requires a special approach.Solar elements have sandwich structure of glass substrate and cover, as well as a very thin semiconductor layer. CdTe semi-conductor can be recycled by flotation. Within the RESOLVED (LIFE European Framework) R&D project on the recycling of solar elements the surface properties of pure CdTe semiconductor and pure glass were investigated by the measurements of zeta-potential using Zeta PALS Brookhaven instrument at University of Miskolc. Applied surfactants were: potassium ethyl xanthate; the anionic oxhydryl Aero Promoter 825 or Flotinor SM 35; the cationic Armoflote 43 or Armoflote 64, as well as Hostaflot LET (dithiophosphoric acid diethyl ester) and Hostaflot M91 (mercaptobenothiazole). The tested electrolyte was sodium-silicate. Zeta-measurements were carried out in full pH-range. Interfacial interactions were detected and interpreted. The basic results were verified by the flotation kinetic tests.Finally, the flotation technological experiments were carried out at a semi-technical scale using the real obsolete solar elements. The particle size at the liberation degree of 98% was as fine as below 5 µm. A special flotation cell providing the generation and distribution of very fine air bubbles was built. The pre-concentrate for the manufacturing of the test solar module was performed and transported to the BAM Institute (Berlin), the principal co-ordinator of the Project, and then further to the First Solar (USA) where a new panel was manufactured using recycled semi-conductor."

Jan 1, 2016

By J. R. Pronovost, P. M. Tiley, D. W. Watts

"In 1980, J.S. Redpath Limited were retained by Dickenson Mines Limited to increase hoisting capacity from 700 to 1000 tons per day. The hoisting capacity of the present skip-over-cage system could not be increased significantly through design modifications. The other constraint was a minimum of disruption to the current production. The Dickenson shaft was a three-compartment shaft from surface to the 8th level and four compartments before the 8th to the 23rd level. The solution to the problem was to remove the services from the shaft man-way compartment from the 8th level to surf ace by drilling a borehole close to the shaft and rerouting those services through the borehole to the 8th level. A service compartment would then be available from surf ace to the 23rd level.By providing a service hoist in this compartment, the skip hoist would then be free to produce the 1000-tons/day required production. This paper will describe the search for the required hoist and the friction hoist selected for the project, and trace the design modifications required to modify the hoist to suit the Dickenson application and satisfy the Department of Labour safety requirements.The paper has been co-authored by J.S. Redpath Limited and C.L. Tiley Associates, who participated in the design changes and eventual commissioning of the hoist.IntroductionIn the earl y part of 1980, J.S. Redpath Limited conducted an engineering study on the Dickenson Mines Limited No. 1 Shaft materials handling system. The object of the engineering study was to investigate the possibility of increasing the tonnage hoisted from the No. 1 Shaft complex by adding a service cage compartment and service hoist. This would permit utilization of the existing hoisting plant solely for production hoi sting. A further consideration of the engineering study was that any alterations had to be accomplished with little, or no, interruption to production."

Jan 1, 1982

By J. R. Pronovost, P. M. Tiley, D. W. Watts

"In 1980, J.S. Redpath Limited were retained by Dickenson Mines Limited to increase hoisting capacity from 700 to 1000 tons per day. The hoisting capacity of the present skip-over-cage system could not be increased significantly through design modifications. The other constraint was a minimum of disruption to the current production. The Dickenson shaft was a three-compartment shaft from surface to the 8th level and four compartments before the 8th to the 23rd level. The solution to the problem was to remove the services from the shaft man-way compartment from the 8th level to surf ace by drilling a borehole close to the shaft and rerouting those services through the borehole to the 8th level. A service compartment would then be available from surf ace to the 23rd level.By providing a service hoist in this compartment, the skip hoist would then be free to produce the 1000-tons/day required production. This paper will describe the search for the required hoist and the friction hoist selected for the project, and trace the design modifications required to modify the hoist to suit the Dickenson application and satisfy the Department of Labour safety requirements.The paper has been co-authored by J.S. Redpath Limited and C.L. Tiley Associates, who participated in the design changes and eventual commissioning of the hoist.IntroductionIn the earl y part of 1980, J.S. Redpath Limited conducted an engineering study on the Dickenson Mines Limited No. 1 Shaft materials handling system. The object of the engineering study was to investigate the possibility of increasing the tonnage hoisted from the No. 1 Shaft complex by adding a service cage compartment and service hoist. This would permit utilization of the existing hoisting plant solely for production hoi sting. A further consideration of the engineering study was that any alterations had to be accomplished with little, or no, interruption to production."

Jan 1, 1982

"Real-time, on-stream analysis of the metal content of process slurries is an essential prerequisite for process monitoring and advanced control of mineral processing circuits. On-stream X-Ray Fluorescence (XRF) sensors for base metal applications are available commercially and form the basis of many plant monitoring circuits. To date, these commercial technologies have been insufficiently sensitive to measure precious metals such as gold and platinum group elements, typically present at part-per-million (ppm) and sub ppm levels. CSIRO has developed a novel X-ray based technology, called UltraGold, which enables detection of gold in slurries on a real-time basis with a precision below 100 parts-per-billion. This technology is based on the use of advanced X-ray optics, extensive Monte Carlo computer modelling for analyser design, high accuracy X-ray spectrum fitting where the X-ray intensities are matrix corrected. In this paper, we will introduce this technology and discuss the results of a proof of principle study performed in the laboratory with plant slurries (tailings and concentrate) from an Australian beneficiation plant. Finally, we will discuss further planned improvements. As projected grades in (gold) mining around the world fall and several large-scale mines approach the limits of their economic reserves, this method can enable significantly reduced operating costs by rapid analysis to improve circuit efficiency and hence improve recovery significantly.INTRODUCTION This paper describes a study undertaken to explore the feasibility of applying CSIRO?s UltraGold XRF technology to the on-stream measurement of gold in process slurries. The provision of rapid, accurate information of gold grade in feed, tailings and concentrate streams would facilitate significantly improved process control and early detection of plant upsets, resulting in substantial cost-savings. CSIRO have patented X-ray fluorescence (XRF) techniques for the analysis of key elements in slurries present at part-per-million (ppm) and sub-ppm levels. Conventional, commercially available on-stream XRF instruments generally have detection limits in the tens of ppm range, precluding their use for analysis of elements like gold that are mined and processed at much lower concentrations."

Jan 1, 2017