Search Documents

By M. Mirnezami, D. Lascelles, J. A. Finch, E. El-Ammouri

"In a previous publication, the depressant action of Mg above pH 10 on Cu-activated sphalerite was described (Lascelles et al., 2001). In the present communication, a second role, aggregation is introduced.Aggregation (i.e., the tendency of particles to cluster) is measured using settling rate and turbidity converted to an aggregation index (AI) where 0 corresponds to dispersed and 1 to aggregated. Surveys of Cu and Zn flotation stages at four concentrators showed the A1 increased significantly above pH 9. The metal ions identified in the process waters, principally Ca and Mg, were tested to determine which might be responsible. The presence of Mg was found to be the most important, 50 ppm Mg having a greater impact than 500 ppm Ca fkom pH 9 to 1 1. In one plant, poor repeatability in A1 was suspected to be related to varying Mg levels; doping with Mg significantly increased AI.In both aggregation and depression, therefore, the common feature is the impact of Mg at pH > 9. Over this pH range Mg forms a range of hydroxy species, including Mg(OH)2 precipitates. Suggested aggregation and depression mechanisms associated with these precipitates are introduced. Possible problems and opportunities arising from the findings are discussed.INTRODUCTIONProcess waters in flotation circuits contain a variety of metal ions that may introduce unwanted activation or depression. Two common metal ions are calcium and magnesium. Typical concentrations are in the range 50 ppm Mg and 500 ppm Ca (Marticorena et al., 1994, Basilio et al., 1996, Negeri et al., 1997, Nesset et al., 1998)."

Jan 1, 2002

By K R. Brentley

"Tshepong Mine, Harmony’s largest gold producing mine, is situated in the Free State portion of the Witwatersrand Basin, east of Odendaalsrus and north of Welkom, South Africa. The Basal reef is a narrow tabular conglomerate and is the main gold bearing ore body. The strata strikes mainly in a northsouth direction with an average dip of 22 degrees. Currently mining takes place at depths of between 1 690m and 2 150m below surface. The Basal reef unit consists of a conglomerate ranging between a few and 30cm in thickness. Some 80-90% of the gold occurs in the lower portion of the conglomerate. Directly above the conglomerate is a quartzite placer unit, the Basal quartzite, which is a clean, hard competent rock and varies in thickness between 50cm and 200cm. The Basal unit is overlain by the Khaki shale which can vary between 30cm and 500cm in width. It is weak and incompetent khaki coloured chloritic shale.A method of stoping, termed “undercut”, is practiced in order to remove the lower 15-20cm of the gold rich strata. The method entails removing this portion along with some 70-80cm of footwall host rock which is a strong competent quartzite. The hard competent quartzite overlying the conglomerate is left in-situ to form a competent hangingwall which can stabilize and prevent exposure of the weak Khakishale. This method of extraction was developed through trial and error and has been used reasonably successfully since its inception in the early 1960’s where the method was developed to extract the Basal reef at the Western Holdings Mines. Recently prospect drilling and a number of localised hangingwall failures indicated that the residual quartzite beam could be less than 60cm and in some instances as thin as 30cm in certain areas of the mine. The result of this is a less stable hangingwall which not only poses a safety risk to workers in these areas but also had the potential of locking up some 840 000 Tonnes of gold bearing ore. At the present gold price this amounts to revenue of approximately ZAR1.5 billion (U.S. $143 million).This paper discusses the method of “undercut stoping” and existing practices in place at Tshepong Mine. It also explores new initiatives such as the use of a simple freely-supported elastic beam solution to perform back analysis, on-site data capturing of beam thickness and support geometries in order to develop empirical design charts and numerical modelling to assist in the verification of the empirical design method."

Jan 1, 2015

By J. Palarski

In the Polish coal mining industry, the use of mine waste in underground backfill has been the most common means of providing ground support to minimize surface subsidence, increasing extraction ratios, and reducing the quantity of waste for surface disposal. Over the last decade attention has been focused on the use of different waste as filling material of underground workings and grouting of roof fall rocks in caving area. In the paper, a brief history of the development of fill technology in Polish coal mining industry is presented. Next, the paper discusses various criteria that should be taken under consideration in the preparation process of a fill slurry and grout, fill distribution systems, mining geometry and placement methods. Moreover, in the paper evaluation of the potential of utilizing coarse and fine waste as a resource material in the production of a backfill slurry and grout for filling and injection in abandoned mines is presented.

May 1, 2007

By S. Dessureault, J. Porter, M. Woodhall

Information and communication technology (ICT) is seen as a key source of future productivity improvements in mines. The information technology infrastructure (ITI) necessary to achieve these productivity improvements will come in the form of data integrated from multiple source systems throughout the mining value chain. Two pure approaches are available: supplier-controlled or operations controlled data structures; each strategy has its own advantages and disadvantages. Case studies involving the South African mining industry are used to demonstrate the advantages of using hybrid-controlled data structures. Depending on the level of operational control, new skills are also necessary to be learnt by mining professionals including: information engineering; creating consistent and quality data; and process improvement techniques that use the integrated data for improving the operation.

Jan 1, 2004

By Ainul Akhtar, Steve Cockcroft, Daan Maijer, Carl Reilly, Lu Yao, Jun Ou

A coupled thermal-fluid flow-multicomponent model has been developed to aid in understanding the melting/dissolution behavior of solid Al-rich Material (TiAl) in a liquid titanium pool produced by an electron beam. The model is capable of accounting for the significant phenomena present affecting heat, mass and momentum transport including thermal and compositional buoyancy and Marangoni forces, Darcy attenuation, evaporation, melting and solidification, and the associated release or absorption of latent heat. The modeling results have indicated the compositional fluid flow driving forces (compositional buoyancy and Marangoni forces) contribute significantly to the melting/dissolution process. The model is waiting for validation against empirical data.

Jan 1, 2014

By L. Jiang

This report investigated the dynamic recrystallization (DRX) phenomenon in magnesium alloy AZ31 billets to understand the deformation mechanisms and microstructure evolution during extrusion and other metal forming processes, Compression tests of coarse-grained as-cast magnesium alloy billets containing lamellar Mg17Al12 eutectic phase and (Al, Mn) particles suggest that temperatures higher than 300°C, strains greater than 0,25 and strain rates above 0,l/s lead to the formation of fine DRX grains in the deformed samples. Microstructural observations also indicate particle-stimulated DRX nucleation (PSN) during hot deformation of the AZ31 alloy, facilitated by the presence of Mg17Al12 and (Al, Mn) particles, While the Mg17Al12 is dissolved into the matrix at about 350°C, (Al, Mn) particles may remain effective for PSN at temperatures up to at least 400°C, This study suggests that alloy design with a proper distribution of second-phase particles can provide the desired microstructure for improved properties and formability in wrought magnesium alloys.

Jan 1, 2004

By Georgy A. Cherkashov, Andrey V. Efimov, Yury S. Borodaev, Nadezhda N. Mozgova, Sergey G. Krasnov, Tamara V. Stepanova, Alexander M. Ashadze

"Abstract - A horizontal mineralogical-geochemical ore zonation with a southeast to northwest trending succession of Cu and Fe (Zn) main zones has been discovered in the Logatchev hydrothermal field (14°45??N Mid-Atlantic Ridge). The major minerals are pyrite, chalcopyrite, bornite, isocubanite, digenite and chalcocite. Zn-sulfide, marcasite and covellite are less abundant. Rare minerals are native copper, zincian copper and cobalt pentlandite (first found in oceanic massive sulfides), Cu and Cu-Co-bearing Fe-disulfides. Two groups of the main sulfide assemblages with different copper contents are recognized: Group I comprises assemblages with primary sulfides (isocubanite, chalcopyrite, pyrite and Zn-sulfide; Cu up to 35 wt% in Cu-bearing minerals); Group II contains assemblages with secondary Cu-rich sulfides (bornite, digenite, chalcocite; Cu ~60 wt%) as well as rare minerals (cobalt pentlandite, native copper and zincian copper). The assemblages of Group I formed at a temperature of about 300°C; the sulfur fugacity (log fs2 atm) at 300°C is probably 9.9. Relations between minerals of this group are contradictory, attributed to non-equilibrium environments, and no unified sequence of crystallization of minerals has been determined. Minerals of Group II replace, rim or cross the assemblages of Group I. Group II minerals crystallized in a distinct sequence (cobalt pentlandite-bornite-digenite- chalcocite-native copper), with increasing copper content from the start to the end of the depositional sequence. This may correspond to pH from 7 to 8 near Eh = -0.2 at 250°C. Minerals of this group were generally formed under hypergene alteration processes. Compositions of ore minerals were studied by means of electron microprobe analysis (EMPA) (150 analyses). Narrow composition fields were revealed in all main sulfides, which comprised known experimental data. ZnS contains 6.0 to 28.0 mol.% FeS, which is close to data known for other hydrothermal massive sulfides from the Mid-Atlantic Ridge (MAR). A common admixture in ZnS is Cu (0.16 to 1.32 wt%). Rare grains of unusual anisotropic Fe-disulfides, (Fe0.95Cu0.05)S2 and Cu(Fe,Co)9S20, were found among the ore minerals."

Jan 1, 1999

By Malcolm Scobie

"This paper reviews the evolution of Canadian surface and underground mining automation, principally relating to: advances in communications, initial development of machine teleoperation from line-of-sight remote control, and islands of automation. The eventual role of teleroboties and minewide robotic mining remains to be resolved. The progress and approaches adopted have tended to vary within each sector of the mining industry. Recent information technology advances have made possible the Digital Mine; in which information associated with all mining processes, however dispersed, would be integrated with support systems using new communications technology. The Digital Mine will provide the information infrastructure to serve as the foundation for minewide automation. This paper concludes by reviewing the issues likely to govern implementation success, relating to: mining process design, machine design, machine intelligence, and mine planning and control.IntroductionSignificant advances have recently been made in underground hardrock mine communications and teleoperation. Subsequent R&D efforts are mainly focussing on control systems for various types of machines. In underground potash mining, the realization of automated continuous mining systems appears to be imminent. Recent advances in surface mine dispatching, machine monitoring and global positioning systems (GPS) have tended to reactivate some of the initial R&D enthusiasm developed in the '70s for surface mine automation. Mines at large are approaching a major milestone: the implementation of comprehensive communications infrastructure which proves to be sufficiently reliable and economical to support the automation of routine mine production, either using teleoperated or autonomous machines. This then should motivate a deeper commitment to real time monitoring and management. The communications advances make possible the Digital Mine; in which information associated with all mining processes, however dispersed, would be integrated with support systems using information engineering. The Digital Mine will provide the information infrastructure to serve as the likely foundation for a wide range of automation scenarios. This paper surveys the status and directions of automation development in both surface and underground Canadian mines, pointing to what are seen to represent key technology development issues."

Jan 1, 1995

By K. Sawada

Along with the expanding demand of copper concentrate in Asian countries, custom-smelters have confronted with difficulties of low TC/RC. Now, Japanese Copper Industry have 2 options; investment in mine development and/or recycling of copper scraps. The strategy of global mining companies is analyzed, and implications for Japanese Copper Industry will be discussed from the viewpoint of sustainability of smelters in Japan.

Jan 1, 2014

By H. C. Gunning

SOME small vanadium-bearing deposits on the west coast of British Columbia about 100 miles north of Vancouver are of interest for several reasons. They are of a type that is, so far as we know, unique. They are difficult to identify as being vanadiferous so that, unless they are described, other similar deposits could easily pass unrecognized. Furthermore, although none of them has as yet been proven to be of commercial proportions, no good reason is apparent why larger, and therefore valuable, deposits should not occur under similar geological conditions. The original discovery on Quadra island was made in 1932 and has been recorded by H. V. Ellsworth and H. C. Gunning (l). Since 1932, prospecting in the area has revealed other similar deposits, one about a mile south of the original and another some ten miles to the east, near Menzies bay on Vancouver island. The Quadra Island showings are a mile and a half north of the head of Gowland harbour, a small inlet that is easily reached by gas boat from Campbell river, about four miles to the southeast on Vancouver island. The deposits were examined by the writers in the spring of 1943 in connection with field work sponsored by the Department of Geology, University of British Columbia. We are indebted to Mr. G. A. Dirom and Mr. Lothrop, of Vancouver, for helpful data on the Menzies Bay deposits, and to Dr. V. Dolmage for making a brief trip to Gowland harbour and discussing the deposits.

Jan 1, 1944

By H De Beer

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Nov 1, 2011

By P. van Zyl, M. Lombaard

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Jan 1, 2012

By Asanga S. Nanayakkara

The surface deformations induced by reservoir dilations can be measured using tiltmeters and these measurements can be used to infer reservoir level volume changes by solving an inverse problem. Preferred approach to solve such an inverse problem is to consider more tiltmeter measurements than the number of unknown variables considered in the inverse problem. However, sufficient number of measurement points is not always available due to economical and practical issues. This paper proposes a new approach to circumvent this problem. The new approach entails generation of pseudo surface deformation data by curve fitting tiltmeter measurements using a mathematical function, which delineates three-dimensional characteristics of surface deformation profiles. Then a three-dimensional inverse problem is solved using pseudo surface deformation data. This method is useful in inferring reservoir volume changes with high areal resolution when the number of available measurements is not sufficient to acquire the desired areal resolution.

Jun 1, 2012

By J. A. Vezina

The effects of particle size distribution on metal extraction have been determined from pressure leaching Renzy Mines Limited concentrate with oxygen. Using a pulp density of 30 per cent solids, an oxygen pressure of 80 psig, a temperature of 230°F, a grind of 2.5 hours and a retention of 8 hours resulted in the almost complete dissolution of the nickel and the cobalt and the decomposition of over 96 per cent of the chalcopyrite finer than 20 microns. Only 11 per cent of the chalcopyrite coarser than 20 microns was reduced to smaller than 20 microns.

Jan 1, 1973

By K. B. Chaudhuri, I. D. Webb, F. E. Rachor, F. A. Sauert

"A characteristic of all methods of copper concentrate smelting is that slags with a high copper content are produced at some phase of the operation. Recirculation to the smelting unit, electric furnace reduction or flotation are at present used on an industrial scale to recover the copper from these slags. This paper describes the application of the top-blowing technique, originally developed by KHD Humboldt- Wedag AG for refining of metallic copper, for the treatment of copper-containing slags. By this method, a mixture of a reducing gas and commercial oxygen is blown onto the melt at velocities which can be supersonic from the tip of a water cooled lance. The impingement of the reaction gas mixture on the surface of the slag forms a depression in the molten phase and a deflection of the jet which brings the slag into a rotating motion. This causes high rates of heat and mass transfer. Results of pilot-plant tests for batch and continuous treatment of slags are presented, and the potential applications of top blowing for industrial-scale operation are indicated. In combination with the cyclone as a smelting unit, this process appears to be economic for smelters of very low capacity."

Jan 1, 1980

By A. Brown

"The mining industry is no exception to the general rule that continuing research is essential to good management; in fact, because of the imperfect state of knowledge in regard to many important factors associated with a mineral extraction, mining research assumes a position of unusual importance. On the basis of a recent visit to mining research centres in a number of European countries, the author describes their organization and their role in the mining industries of these countries. Some observations are made on Canadian mining research efforts, with a view to indicating a more systematic basis of procedure."

Jan 1, 1960

By M. G. Mena, M. S. Mena-Junio

Silver (Ag) filler is the most attractive choice among all the conductive fillers of die attach materials for the attachment of silicon devices because of its balanced properties and relatively low cost. However, a major problem of silver is that it electrochemically migrates in the presence of moisture and applied bias. In microelectronic devices, silver migration can occur between adjacent conductors/electrodes, which leads to the formation of dendrites and eventually results in short-circuit failure. In order to assess the reliability of these conductive fillers, an investigation for two types of Agfilled die attach materials was done using the water drop test at room temperature and using a 1000 hour temperature-humidity-bias (THB) test under 85 ºC and 85% RH conditions. Four different bias/voltages and six different electrode distance spacing were used. Both dendrite and cloud/lace-like growths were observed as a result of the electrochemical migration of silver, Water drop test results revealed that increasing the applied bias/voltage and decreasing electrode spacing causes migration to occur faster, thus resulting into shorter time to fail (TTF). It was also observed that the growth rate of the dendrites from the cathode increased linearly as the dendrite approached the anode, probably due to a combination of increased ion availability and electric field. A minimum applied bias of 3 volts was required for migration to occur in Epoxy A as compared to 2 volts for Epoxy C. The higher migration voltage requirement for Epoxy A was attributed to the higher volume resistivity of the said epoxy. In addition to the minimum voltage requirement, it was observed that a minimum electric field of about 1 volt/mm is required for migration to occur. The 1000 hour THB testing did not result into any failures. It is surmised that the presence of condensed moisture is another requirement for migration. Such condition is not present during the THB testing.

Jan 1, 2012

By K Morrison

Different individuals have calculated the boundary stresses around elliptical openings in an infinite elastic medium for various conditions of loading. With caution, such calculations are useful in indicating stress trends in mining. This paper illustrates an application to caving operations and suggests that abnormal field stress would have an adverse effect. Introduction GELDART and Udd (1), applying elastic theory, confirmed, and set out graphically, the stress distributions on the surface of elliptical openings with axis ratios varying from 1.0 (a circle) to infinity (a crack). The loading conditions varied from uniaxial to hydrostatic, and inclinations for the opening, with respect to the stress axis, varied from 0° to 90°. As most mine openings can be generalized into this elliptical conception, the usefulness of the presentation lies in the fact that given reasonable estimates for the stress ratio, the axis ratio, and its inclination, then the trend in stress concentrations as an opening develops can be readily approximated.

Jan 1, 1964

By A. E. Cameron

The theory of atomic distribution of the stranger atoms in the space lattice of the solvent metal has been well developed by Rosenhain. It has long been known that the addition of one metal to another to form a solid solution increases the strength and hardness of the solvent metal. This increase is practically proportional to the amount of added substance up to the limit of solid solubility. To account for this increase in hardness and strength, Rosenhain assumes that the stranger atoms occupy positions on the solvent metal space lattice. Atomic attractions about the stranger atoms will not be the same as in the case of the pure metal, and there will thus be a disturbance of the orderly arrangement of the atoms on the space lattice, or a distortion of the lattice. Such a disturbance would interfere with the ease of slip along the planes and would thus tend to promote strength and hardness. Rosenhain notes that not only may there be a local disturbance of the lattice about the stranger atom but there may well be also a measurable change in the dimensions of the lattice as a whole. The relative amounts of local and general distortion of the lattice will depend upon the nature of the lattice itself. As Rosenhain says, "If the lattice is comparatively soft and flexible the distortion is likely to be largely local. In a stiff lattice, however, local distortion will be resisted and there will be a correspondingly increased general distortion."

Jan 1, 1927

By N. Romani, R. Provost

"Commissioning of a circulating dry scrubber (CDS) plant was recently completed at an existing facility in Québec, Canada. The CDS plant treats the sulphur dioxide off-gas emitted from rotary kilns in order to meet increasingly stringent environmental requirements. This installation enables the existing facility to reduce their sulphur emissions by over 90%.Proper planning of the different commissioning stages and staffing an integrated team are the most important factors required for a successful plant start-up. A strong Operational Readiness plan must be in place as early as the start of construction in order to ensure a smooth transition from commissioning to operations. Plant performance can meet or exceed performance criteria within the required timeframe if the proper group dynamic and good communication is established between construction, commissioning and operations teams.The road blocks encountered are often from systems that one assumes will operate without trouble such as air-conditioning, or design assumptions that were taken years earlier in feasibility process stages, namely the capacity of existing systems that will connect the new plant to the existing facilities. The challenges associated with rectifying these issues in addition to the requirements to properly start-up and operate a new plant without impacting production are great, and it is imperative to have the necessary resources to react quickly to any problems.IntroductionCommissioning of a circulating dry scrubber (CDS) plant was recently completed at an existing facility in Québec, Canada. The CDS plant treats the sulphur dioxide off-gas emitted from rotary kilns in order to meet increasingly stringent environmental requirements. This installation enables the existing facility to reduce their sulphur emissions by over 90%.The CDS ProcessA general overview of the CDS process is presented in Figure 1 below. The combined, de-dusted off-gas from multiple kilns is sent to the CDS, which acts as an entrained fluid bed, where the gas is contacted with a water mist, re-circulated solids and hydrated lime. The SO2 from the gas stream and the available calcium hydroxide (Ca(OH)2) from the hydrated lime dissolve in the water and react to ultimately form calcium sulphites and gypsum. The solid residue (referred to as CDS residue), is the primary by-product of the process."

Jan 1, 2016