Search Documents

By E. Wasmund

"Sandfire’s DeGrussa Copper-Gold operation in West Australia is a new high grade copper sulfide mine, which includes a 1.5 Mtpa concentrator which was completed in 2013.Early after commissioning, it was identified that the flotation capacity in the all-mechanical cleaner circuit was not sufficient. In order to improve recovery, the tail from the cleaner scavenger was sent back to feed the rougher scavengers. Test-work was done on-site to evaluate the possibility of using a flotation column as a pre-cleaner. A CavTube™ sparging system was selected, which is especially effective for fine ore particle flotation. Test-work was conducted at site using a 150 mm diameter unit, and then confirmed on a 500 mm diameter unit. A 4250 mm diameter full scale unit was installed in Q4 2014 and commissioned in Q1 2015. This unit gave some significant advantages including a reduction in re-grinding requirements, elimination of a circulating load and increase in the recovery of copper in the cleaner circuit and overall circuit.In this presentation, the benefits of columns and cavitation sparging for floating fine particles and rejecting fine entrained gangue will be explained. Also, the results from a lab unit and a pilot unit will be compared against the results of the full-scale unit. The paper will demonstrate the scalability of flotation columns, and which phenomena and scale-up criteria must be considered to be successful. Finally, some general observations will be made about the importance of columns in copper cleaning circuits.IntroductionSandfire Resources’ DeGrussa copper-gold concentrator is located approximately 900 km north-north-east of Perth in Western Australia. The project area landscape is scrubby mulga lands with few notable features. The climate is arid with high temperature and heavy summer downpours."

Jan 1, 2016

By Kallioinen Jouko

"Advanced Flotation Technology is the application driven design of Don-Oliver flotation cells to achieve the optimum performance for each type and grind of flotation. Optimum performance is the combination of both recovery and selectivity.Optimized performance is the combined product of optimized mixing and effective froth removal. Optimized mixing is applied to roughers, scavengers, cleaners and specialty cells such as those to float hydrocyclone underflows in both primary and regrind circuits in order to reduce overgrinding. Effective mixing for fine material is easy, but overmixing reduces selectivity in frothbed.Selectivity in flotation is an important target, especially when treating complex ores, and parameters in frothbed have been examined to improve the separation of minerals and eliminate circumstances that reduce separation rate.Advances in process control have been achieved with expert controls and instructive operator information data. This has gained a higher degree of understanding of cell operation and ore type being processed to be used in future process development work. Excellent results of this Advanced Flotation Technology have been achieved and designs through 7000 cu ft (200 m3) are currently available for high capacity concentrators. This paper will detail how flotation cells are more responsive to the exact requirements of the duty specified."

Jan 1, 2000

By V. N. Rampton, C. F. Gleeson

"Exploration results over three overburden drilling anomalies defined by the Ontario Geological Survey in 1981 in the Kirkland Lake area, Ontario are presented. The anomalies come from lowland areas where overburden is thickest. By mapping the bedrock and surficial geology, by prospecting, humus sampling and shallow till sampling over the surrounding upland surfaces, one can initially evaluate such overburden drill anomalies without costly reverse circulation drilling. The drilling should follow, if necessary, only after surficial base data has been obtained. Preliminary work on these three properties has defined the presence of at least two styles of gold mineralization. One occurs in silicified zones in intermediate volcanics closely associated with northwesterly trending faults and shear zones. The second occurs in quartz-carbonate alternation zones in volcanics intruded by quartz-feldspar porphyry dykes. IntroductionThe three examples presented in this paper present first-hand information on an approach to the follow up of several geochemical anomalies that were found by the Ontario Geological Survey when they carried out reverse circulation overburden drilling as part of the Kirkland Lake Initiative Program (KLIP) in 1980 (Routledge et al., 1981). The initial approach is relatively simple, systematic, and cost and technically effective. It readies the properties for further exploration, or conversely, it could downgrade the properties as viable gold targets."

Jan 1, 1987

By Nicolas Gatelier, Sophie Laurent, Thierry You

Hard-rock caverns for hydrocarbon storage are a very particular type of underground facility controlled not only by local administrative and regulatory constraints that can be very specific, but also by the possible risks of geotechnical or geomechanical failure. Each such facility throughout the world is a prototype that needs to be adapted to very different site conditions. The straight forward application of design methodologies from relatively similar fields (mines, tunnels) can be very useful, but risks holding back the scientific and technical improvements needed by an engineering industry in full development. Here we look at various case histories and at problems that have been raised where recent attempts at standardization would appear to have been ill adapted, and where storage designers, through experience and judgment, may still provide innovative engineering solutions.

Jan 1, 2015

By Baki Özüm

Early evaluations of Pasquia Hills kerogen shale deposits by Geological Survey of Canada, Saskatchewan Geological Survey, Manitoba Energy and Mines and Sun Oil Company, using modified Fischer Assay, Rock-Eval and other techniques, estimated recoverable reserves of about 2.6x109 barrels of oil in areas favorable for strip-mining; each metric ton of ore was determined to yield about 30 L to 50 L of shale oil remarkably high in aromatic compounds. Western Petrochemical Corp. (WPC) is holding two Oil Shale Exploration Permits covering about 76,635 hectares in the Pasquia Hills Region of eastern Saskatchewan and conducting a 15-corehole drilling program to determine stratigraphic correlation on both first and second white specks kerogen shale. In this program, correlation will be established between oil yield and oil quality, using different retort techniques, including modified Fischer Assay, steam retort and Rock-Eval. Results will lead to further resource evaluation and to a preliminary engineering design for a shale processing plant, including selection of retort process, upgrading of shale oil to petrochemical feedstock, hydrogen management, energy balance and evaluation of environmental impact.

May 1, 2002

By Floyd Smith

Based on underground observations made in .the coal mines of the Dominion Coal Company Ltd., this paper deals with the stress phenomena in the approach roads and headways and in the gob areas associated with the longwall method of total extraction. The deformation of roadways during development and the deformation of roadways during the total extraction period is delineated and presented in graphical form .. Conclusions are made as to the feasibility of the introduction of the retreat method of longwall extraction in one of the colhenes. The importance of future studies are enumerated, especially. those pertaining to the determination .of the opti.m.um sizes of protective pillars and to increasing the efficiency of the current methods of artificial roadway support.

Jan 1, 1967

By Sune Eriksson, Stig Peterssonsune, Christer Fridfeldt

"Boliden Metal Corporation has developed a technique to treat complex copper concentrates containing large amounts of lead, zinc, arsenic, antimony and bismuth which cannot be treated in conventional smelters due to the impurities.Tests were carried out to treat such complex copper concentrates in the TBRC. They were performed in a pilot-plant TBRC with charges of 5 tons. These tests resulted in a new method to treat complex copper raw materials and produce a blister copper low in impurities. The background and data from the test work are presented as well as a flowsheet for a full-scale process.IntroductionThe Ronnskar Works is situated on the coast of the Gulf of Bothnia, 40 miles east of the Boliden Mine. Smelting began at Ronnskar in 1930 to process the complex ore extracted from the Boliden Mine. The Ronnskar Works has subsequently developed into a relatively integrated smelting plant.Copper and lead sulphide concentrates from Boliden's own mines as well as purchased copper raw materials are processed. The main products are refined copper and lead, but full utilization of the raw material also yields other metals and some metallurgical and chemical by-products. The products include gold, silver, zinc clinker, white arsenic, arsenic salts and arsenic metal , selenium and selenium compounds, nickel sulphates, sulphuric acid and liquid sulphur dioxide."

Jan 1, 1981

By Brad Sampson

Project Ownership ?Discovery Metals Limited ?ASX (DML), BSX (DML), AIM (DME) ?Market Cap AUD 195M ?Key assets ?Boseto Cu ?Dikoloti Ni The Boseto Copper Project ?Location ?Setting ?History ?Status ?Future

May 1, 2010

By D. Eriksen

Zero Emission Gas power, ZEG, is a novel concept where a high temperature solid oxide fuel cell (SOFC) is integrated with a reforming reactor producing hydrogen from natural gas through Sorption Enhanced Steam Methane Reforming (SESMR). The SOFC is used as a high temperature heat source for regeneration of the CO2-absorbent. Moreover, by using part of the produced hydrogen as fuel for the SOFC, the waste heat of the process is considerably reduced. Thus, the process has a very high thermal efficiency and produces both electricity and hydrogen from natural gas. In addition, a stream of pure CO2 is produced in the regeneration step and can be deposited or used commercially. Initial cost estimates indicate a cost of electricity and a cost of hydrogen well below today's prices. A small (1kWel + 1kW H2) demonstration set-up is under construction and experimental results and related research will be presented. This set-up comprises one 2.5kWth H2 SESMR-reactor (about 0.85 Nm3/h H2) operating batchwise with dolomite as the CO2-sorbent. The reactor developed is designed like a parallel plate heat exchanger where the mixture of sorbent and reforming catalyst is packed between the heat exchanging plates. The demonstration set-up includes a 1kW SOFC operating in a continuous mode. The set¬up will therefore demonstrate continuous simultaneous hydrogen- and electricity production, but cannot demonstrate simultanuous electricity- and CO2-production. The set?up is well equipped for on-line monitoring of gas composition, flows and temperatures. This important part of the demonstration set-up is developed and provided by Christian Michelsen Research (CMR). A minor part of the project is the development of a continuous circulating fluidized bed SESMR-reactor system and in another related project the focus is on the development of more suitable sorbents. In these two projects co-operation with University of British Columbia and Lousianna State University, respectively, is highly appreciated.

Jan 1, 2005

By S. Kamado

Development of new SF6 alternative cover gas with low global warming potential is strongly desired for melting and casting of magnesium alloys. We have tried to apply several kinds of HFC and HFE gases with low potential from 30 to 950 as protection gases to AZ91D alloy melt in the temperature range of 650 to 800°C. As a result, protective film consisted of MgF2 and MgO is formed on the melt surface and ignition-proof effect is sufficiently obtained at all the temperature ranges even when flow rates of mixed gases containing CO2 as a carrier gas are almost the same as those using SF6 gas. Reduction of global warming potential exceeds 98% at 650°C and 89% at 800°C in comparison with a mixed gas of CO2 and SF6.

Jan 1, 2006

By Yoginder P. Chugh

This paper discusses an ongoing field study in southern Illinois (USA) that focuses on: 1) Identifying mechanisms of instability in the set-up rooms (SR) and their T-junctions with headgate and tailgate entries, 2) Developing alternate 3-entry and 4-entry set-up rooms geometry using 3-D numerical analyses, 3) Implementing developed geometries in cooperation with mining professionals and regulatory agencies, and 4) Demonstrating performance of implemented geometries through field monitoring. Illinois longwall mining operations typically experience ground control problems (roof falls, rib sloughing, floor heave, etc.) within SR layouts and around the T-junctions of SR. These occur around the areas where the SR for adjacent longwall face (to be mined) connect with the SR of the previously mined face, and around the tail-gate entries of the mined-out longwall face and around the T-junctions of SR. The problems manifest as highly fractured immediate roof strata, major shear zones in the roof, horizontal displacements within the excavations that result in shearing off the heads of the bolts, floor heave and severe rib sloughing. Similar observations have also been made in longwall mining in Utah.

Aug 1, 2013

By Brennan Lang

Why Seal Tunnels? ?Restore groundwater levels to pre-mining conditions. ?Saturate rock mass to reduce acid rock drainage. ?Reduce discharge flow to the environment. ?Reduce or regulate flows to a water treatment plant.

May 1, 2002

By H. Utsunomiya

Most magnesium alloy sheets show low deformability in rolling. Edge cracks and transverse fractures are common difficulties. In addition, rolled sheets show well-developed basal texture <0001>//ND. The texture causes high anisotropy in mechanical properties and low formability in subsequent metal forming. Differential-speed rolling, where the upper and the lower rolls rotate at different speeds, introduces shear deformation through the thickness. Not rolling texture but shear texture evolves in the sheet so that the asymmetric rolling can be a method of texture control. However the primary slip system of the hcp alloy, is basal, the shear texture should be also basal. Differences between the two basal textures, i.e., the rolling texture and the shear texture, have not been understood completely. In this study, conventional (same-speed) rolling and differential-speed rolling have been applied to commercial AZ31B sheets at 623K. Microstructures, textures and mechanical properties of the rolled sheets before/after annealing are compared. It is found that the basal texture is more pronounced by the asymmetric rolling. On the other hand, the asymmetric rolling is effective to decrease the grain size and the planar anisotropy.

Jan 1, 2006

By F. Osmond, R. Kelly

"Malcolm Knowles, the famous adult educator once wrote: ""What a challenge we in human resources development face if we are to avoid the obsolescence of our workforce. I can foresee this challenge requiring that we reconceptualize (...) and redefine the role of HRD, away from that of managing the logistics of conducting training activities to that of managing a system of learning resources"".The context in which this was written surrounds the subject of adult education and the need for business and industry to change its approach to the treatment of adults as learners. In explaining what &apos;managing a system of learning resources&apos; means, Knowles refers to line supervisors and managers as the most ubiquitous resources for day-in and day-out employee development. In many organizations training has been largely a staff rather than line responsibility. Even where trainers reported to line management, it was still seen as a staff function performed by a few specialists.This change referred to by Knowles places a much heavier responsibility on line supervisors and managers for the development of their personnel than has traditionally been the case. Managing that change - handing over the responsibility to the line organization - is the supreme challenge for the HRD function.Just why is this change necessary? Because too often, the learner does not effectively use on the job what he or she learned in the classroom. In fact, learners often discard new methods and revert to the older ways. The reason training does not stick is that the systems for training and work management are most often separate entities and while one may support the other, they need to be a single integrated system in order to ensure the transfer to the job effectiveness of training and some real value for the training dollars.Because much training can be wasted, steps have to be taken to ensure that it fulfills its intended purpose. The effective and continuing application of knowledge and skills that learners acquire can only be realized when line supervisors and managers are at the centre of the training system.This paper describes how such a systemis being developed at the Iron Ore Company of Canada (IOC) as a functional training program is introduced. The following text provides background information on the IOC - who they are and where they are located, a definition of functional training, an evaluation of the suitability of this approach for adults in industry, a description of how the program is being implemented at IOC and some observations that have been made as this change is experienced."

Jan 1, 1995

By Rick Moignard

Relationships between Information Technology providers and their clients are often segmented according to job specific tasks. As a consequence, technology providers tend to focus on automating repetition and complexity, resulting in software that improves individual productivity while failing to address the interdependency of mining functions. For this reason, technology vendors like Gemcom are following partnership approaches with their clients, engaging corporate and operational stakeholders to better understand mining business objectives. This presentation examines some of the approaches that help foster the development of solutions that leverage the information produced during mine operations to improve downstream process control and tactical decision support.

May 1, 2006

By Antonio Fontana

"Environmental problems encountered with the use of diesel equipment in underground mining operations are discussed. The concept and procedure o implementing the Health Effects Index equation as a means of quantitatively assessing an underground working environment is outlined and sample calculations are present ed. Advantages and disadvantages of utilizing this method are also discussed.IntroductionWith the introduction of diesel-powered mining equipment in the 1960s there arose several question s for the environmental engineer to consider. These included: 1. What are the constituents of diesel exhaust and how can they be detected and evaluated?2. What are the toxicities and long-term health effects of these constituents?3. What is the ventilating volume required to maintain the concentration of these constituents below toxic levels?Diesel engines are a class of reciprocating, internal combustion engines in which relatively high compression ratios are used to generate high air-charge temperatures, which cause ignition of fuel to occur spontaneously. Ideally, perfect combustion of the fuel would produce an exhaust consisting solely of nitrogen (N2), water (H2O), carbon dioxide (CO2) and oxygen (O2). However, because no combustion process is perfect, relatively small quantities of imperfect-combustion products, or pollutants, are also generated. These include hydrocarbons (HC), carbon monoxide (CO), nitric oxide (NO), nitrogen dioxide (NO2), carbon (C) or soot, and sulphur dioxide (SO2).Currently, the Regulations for Mines and Mining Plants, made under the Occupational Health and Safety Act (Section 176), stipulate that weekly tests shall be made to determine the carbon monoxide (CO) concentration in the undiluted exhaust and at the operator&apos;s position, and the nitrogent dioxide (NO2) concentration at the operator&apos;s position. Also, the aldehyde (as HCHO) concentration in the atmosphere, at the operator&apos;s position, is to be measured at least every three months. Threshold limit values (TLVs) have been established for each of the three combustion products, and each is regarded as a separate entity. Consequently, this does not allow for consideration of interactions and possible synergistic effects between the various exhaust components."

Jan 1, 1982

By S. Srinivasan, R. Coté

"India is undergoing a massive electrification program using local coal to provide fuel for thermal generating plants. The Rajmahal mine in northern Bihar is scheduled to produce coal at the rate of 10 million tonnes per year by the end ofa sixty six month contract with MET-CHEM Canada Inc. for mine development. In order to control maintenance performance and warehouse inventory MET-CHEM is installing some proven computer-controlled programs and will provide extensive training to ensure that the systems are properly used. The programs are Maintenance Planning and Control System (MPCS) and Materials Management System (MMS), both of which were developed and used by Quebec Cartier Mining Company at its iron ore mine in northern Quebec. In addition, a Predictive Maintenance Program (PMP) using vibration analysis will be introduced . This paper discusses the three systems.IntroductionIndia is currently undergoing a massive countrywide industrialization and electrification program. Most of the power will be supplied by coal-fired thermal electric plants.One of the mines being developed as part of the over-all program is the Rajmahal Open Cast Coal project in the Godda District of Bihar, approximately 270 km north , and slightly west of Calcutta.The project is based on an agreement signed in January, 1989 between two government organizations - Canadian Commercial Corporation (Ccq and Coal India Limited (CIL). MET-CHEM Canada Inc. (MET-CHEM), an international consulting engineering organization which has worked in India since 1976, is CCCs Canadian executing agency for the project. METCHEM was the engineer-constructor and mining associate for the development of the 7.5 mtpy Kudremukh Iron Ore Project. This US$430 million project was completed on schedule and under the original budget estimate. The Rajmahal deposit is the responsibility of Eastern Coalfields Limited (ECL), a subsidiary of CIL. The project is to produce coal at the rate of 10.5 million tonnes per year in 1994."

Jan 1, 1991

By Sylvain Castonguay, Sylvain Pilon

"Operator competency is an important factor in the safe and successful operation of today’s complex processes. Competent process unit operators deliver superior performance and results. In greenfield projects, operator competency is particularly critical, as the lack of specific operations experience must be offset with proven practical knowledge and skills to avoid mistakes that can cost millions in terms of start-up delays, production losses and equipment damage. It is, therefore, important to know precisely what competencies are required for a project or site, and what any gaps in operator competency need to be addressed and improved. The success of plant commissioning, start-up and sustainable operations is directly tied to operator competency. The significant investments required for new projects, the exploitation of more challenging ore bodies, and the increasing complexity of plant operations have placed renewed emphasis on the need for competent operators. Furthermore, many large capital projects are being developed in remote regions, often with ties to the delivery of social benefits for the local population in terms of jobs, training and other development opportunities. While automation and processing technologies have helped do more with less, indicators now point to a bottleneck in human performance limiting operational results.Automation industry development in managing abnormal situations, including solutions for simulation and operator training, has produced applications to provide customized and flexible training methods. This paper will discuss tools to automate the operator competency process in order to guide trainers to effectively teach, measure, control, provide feedback, and monitor operator skills. Today’s competency management solutions can be effectively applied throughout the course of an operator’s professional life, as a guide to hiring new operators, for developing competencies to support operations, and also to develop and refine best practices and share lessons learned."

Jan 1, 2016

By Richard Burt

"In seeking to supply the ever increasing needs for raw materials, the mining industry has been required to develop lower grade resources in increasingly remote regions of the world. This has resulted in the extension of many frontiers, both technologically and geographically.The accent of mineral processing research over the last few decades has been to “do existing things better”. There have been many breakthroughs in equipment and processes; however in general the accent has been to increase capacity of existing unit processes, often by orders of magnitude, or to refine the process itself by basic research and development. This has lead to added sophistication, enabling the process engineer to maintain optimum performance of his equipment while reducing the cost, and the amount of labour needed to operate the plant.While much of the increased requirement for resources is handled by the development of ever larger, lower grade orebodies, a significant portion still comes from the small miner - even the artisanal miner - operating in remote and often politically sensitive parts of the world. For them, innovation and simplicity are the keys, not sophistication.The tension between sophistication and simplicity - or research and reality - is specially evident in the area of gravity concentration of rare metals, such as tin and tantalum. This paper looks at this tension, primarily from the eyes of an operator and seeks to put into perspective the two paradigms."

Jan 1, 1999

"INTRODUCTIONGold tailings retreatment plants have been operated for many years throughout the world. Several large tailings retreatment facilities have been operated profitably in South Africa since 1976 and there are tailings retreatment operations in Canada currently in production with more in the feasibility stages.The Timmins Gold Tailings Project of ERG Resources Inc. was designed to treat 8,000,000 tonnes per annum of gold tailings for an eight month operating season, and commissioning of the operation began in July 1988. The payback period for this project is about 3 years which corresponds to an IRR of 30%.This report summarizes the metallurgical characteristics of the reclaim tailings, describes the process flowsheet which was developed to enable ERG to economically recover gold from the Timmins area tailings, and reviews commissioning activities."

Jan 1, 1989