Search Documents

By Ron Bradburn, Derek Perkins

"The Brenda mine is located in south central British Columbia, 22 km north west of Peachland, in the heart of the Okanagan Valley. Situated at an elevation of 1500 metres, the mine area straddles the divide between the headwaters of Trepanier Creek and Peachland Creek. These flow into Okanagan Lake, the chief valley water resource located 1100 metres below. The creeks are of great significance to the water management of the area as they constitute the water supply for the Municipality of Peachland, a thriving retirement community with a population of 5000. A location map is shown in Figure 1.The history of the Brenda Mine operation has been well documented previously. After twenty years of operation, the open pit mine shut down in June 1990 due to the depletion of its ore reserves. During the course of its life, it produced 109 million tonnes of waste rock which is thought to contain approximately 0.10% copper as chalcopyrite and 0.015% molybdenum as molybdenite stored in four rock piles around the pit. Similarly, approximately 200 million tonnes of tailings were produced grading 0.015% copper and 0.005% molybdenum. During operation, tailings were hydrocycloned to produce a coarse sand for dam building with the fine slime stored behind the dam. It is estimated that 40% of the tailings were used for the dam construction. The layout of the mine site is shown in Figure 2.The mine was operated under a zero discharge permit. This was achieved by diverting practically all surface water flowing towards the mine area around the site. Water affected by mine operations, was discharged to the tailings impoundment, and recycled to the mill for reuse. The recycle rate was 90% and seepage from the tailings embankment and saddle dam was pumped back to the tailings pond. Because acid drainage was not a problem with the low grade Brenda rock, runoff from the rockpiles was initially released to the local environment. However, due to the alkaline nature of the waste rock, dissolution of low concentrations of molybdenum in the site runoff waters became evident by the late 1970's. The molybdenum content of Peachland Lake, the water reservoir for the municipality of Peachland, approached the Canadian Drinking Water Standard of 0.25 ppm. By 1979, a series of diversion and collection ditches was completed to direct all runoff water from the rockpiles to the tailings impoundment area. This had a significant detrimental effect on the site water balance causing it to go into a considerable surplus condition. During normal operation, this oversupply was contained by the rate of tailings dam building. An economic shutdown of the mine during 1984 forced a limited discharge from the site to protect the integrity of the tailings dam."

Jan 1, 1995

By M. Bryson, S. Broom-Fendley, A. E. Brady, W. Dawes, G. Beer, N. Sehlotho, S. Al-Ali, F. Wall

The Songwe Hill Rare Earth Element (REE) Project in Malawi is a near surface carbonatite-hosted deposit with synchysite and apatite as the key REE bearing minerals. A strong focus has been placed on understanding the REE mineralogy of the Songwe Hill carbonatite as REE mineralogical characterization is a crucial component at all steps, ranging from exploration to production, in the development of REE deposits. Extensive mineralogical work has been completed at Camborne School of Mines (CSM), Natural History Museum (NHM) London, British Geological Survey (BGS), Nottingham, Aberystwyth University, Wales, Mintek, South Africa, and SGS Inc. Canada (SGS). The following analytical techniques were used: scanning electron microscopy (SEM), electron microprobe analysis (EMPA), laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS), and QEMSCAN®. The detailed studies have demonstrated that while synchysite is light-REE enriched as expected, apatite, abundant in all stages of carbonatite emplacement at Songwe, is anomalously enriched in mid- to heavy-REE relative to apatite in other carbonatite deposits. The distribution of REE within synchysite and apatite at Songwe has had important implications for the direction of the metallurgical work with respect to the behaviour of light and heavy REE through the flotation and hydrometallurgical stages of the flow sheet.

Jan 1, 2014

By R. P. Kofluk

The nickel-cobalt sulphides produced from limonitic laterite ores by Moa Nickel S.A. in Cuba are refined at the Corefco nickel-cobalt refinery in Canada. Significant economic implications are associated with the refining of precipitated sulphides containing elevated iron contents. The Moa Nickel S.A. operations encompass laterite mining, high pressure acid leaching (H PAL), and ultimately, precipitation of a mixed sulphide product. These processes are reviewed as they pertain to the control of iron and the formation of a mixed sulphide containing nominally 55% Ni, 5% Co and 1% Fe. The contributors to the iron content of the mixed sulphide product are reviewed; the major contributors are the HPAL operation and sulphide precipitation. The precipitation of iron during sulphide precipitation is influenced by the solution acidity, the iron and copper concentrations in the feed solution, and the presence of laterite leach solids. The significance of the copper concentration of the sulphide precipitation solutions is manifested by both physical and chemical modifications of the sulphide precipitates, presumably through the formation of fine copper sulfide seed particles.

Jan 1, 2006

By Joanne G. Petrini

ISO 26000 Unique Process Unique Personality ?Almost 10 years in the making ?What type of standard is this? Different type of ISO Standard ISO 26000 Structure and Substance ?Principles ?Core Subjects ?Implementation Guidance ISO 26000 Impact ?Same old, same old? ?So Is there really anything NEW? ?Should I care??

May 1, 2011

By Dale A. Sketchley

"Abstract - Large differences in gold content between rock fragments or small volumes of unbroken rock, commonly referred to as the nugget effect, are related to sample and subsample weights, crushing and pulverizing sizes, and density, shape and size distribution of gold grains. Gy’s sampling theory, which relates gold grain characteristics to sample weight, fragment size, and error, provides a method of estimating a sampling constant that quantifies deposit characteristics that contribute to the nugget effect.Sampling control tests provide methods for determining the sampling constant. Sampling control charts, comprising nomographs that relate sample weight, error and particle size, use the sampling constant to optimize sample weights and comminution sizes, and to minimize the variability introduced by incorrect or inadequate sampling and sub-sampling procedures. The sampling constant is useful in classifying ores into arbitrary categories according to expected sampling difficulties. Spatial variations in the sampling constant can be used to aid in defining ore types for modeling geological domains, which should have unique sampling protocols. Examples that illustrate the relationship between the sampling constant and expected sampling problems, and the spatial variation of the sampling constant, are given for various deposits. Case histories of sampling programs are presented.Quality control procedures consist of monitoring sample contamination amd accuracy and precision of analytical results. Accuracy, precision and contamination are monitored by including standards, duplicates and blanks into batches of samples being analyzed. Analytical results of standards and blanks are plotted on a batch-and-time basis with control lines at plus or minus two/three standard deviations as confidence limits of the accepted round-robin value. Examples are given that illustrate a laboratory system in statistical control and the various types of problems encountered when interpreting quality control data. These include sample transcription errors, degradation, contamination, sampling errors, detection limit problems, instrumental drift, lack of statistical control, laboratory bias, procedural problems and data tampering.Where bias is negligible, precision, as a function of concentration, can be obtained from duplicates using the Thompson-Howarth precision algorithm, which also allows calculation of the practical detection limit. Examples are given that illustrate variations in precision, with grain size, for different types of duplicates, as well as mineralogical changes and sampling errors."

Jan 1, 1998

By Q. Zhang, J. A. Finch

"Sphalerite flotation in the absence of copper activation at moderately alkaline pH has been observed in laboratory studies. An in-plant test of this observation was conducted at Kidd Creek Mine LTD. using a portable minicell flotation circuit. The results confirm that raising the pH causes sphalerite flotation.The testwork with the minicell circuit is described. The circuit, built around 2, 51 cells donated by the Noranda Technology Centre, was funded by Air Liquide and NSERC. It includes a data acquisition system to monitor continuously dissolved oxygen, pH and Pulp potential.INTRODUCTIONFlotation of sphalerite is normally practised by adding CuSO4 as an activator under alkaline pH. Recently there have been a number of laboratory and plant examples of sphalerite flotation without deliberate addition of cu++ ions (Girczys, 1972; Mukherjee, 1976; McTavish, 1980; Marouf et al., 1986; Mielczarski, 1986; Leroux et al., 1987; Palsson and Forssberg, 1989; Sandoval-Caballero et al., 1990; Zhang et al., 1991).In batch tests, with a sample of Pb/Zn ore from Polaris, Leroux et al. (1987) found that sphalerite became floatable after adjusting pH to 9. 5-11: they ruled out natural floatability or the formation of elemental sulphur on the surface but suspected iron hydroxy compounds were responsible. Sandoval-Caballero (1990) conducted a continuous minicell test at Brunswick Mining and obtained a 44 % Zn recovery and 40.5 % Zn grade concentrate without deliberately adding CuS04 at pH= 10.5. With single mineral studies, Zhang et al. (1991) revealed good sphalerite floatability (over 80% recovery) in pH range 8 to 11 and found that this floatability was related to pH, dissolved oxygen (DO) level and Fe++ species present in the system.To explore further the conditions under which sphalerite can float without addition of CuSO4 , a continuous pilot test using minicells was performed at Falconbridge Ltd., Kidd Creek division. The set-up is briefly described (a more detailed description is given elsewhere in these proceedings) with emphasis on the data acquisition system - dissolved oxygen, pulp potential and pH were monitored continuously. Results of testwork investigating pH, CuS04 addition and gas composition are presented."

Jan 1, 1992

By Johnna Muinonen

"The Thompson Mill processes ores from the Thompson and Birchtree Mines. While the Thompson ore has very little magnesium containing gangue, the Birchtree orebody consists of veins of massive sulphide in a rock matrix that contains a high proportion of magnesium silicate minerals. A significant fraction of the magnesium is floatable, which lead to MgO levels varying from 3-11 wt% in the Birchtree concentrate. The magnesium in the concentrate causes a higher operating temperature in the smelter, reducing furnace life.Birchtree ore represented 20-30% of the mill ore receipts prior to October 2003. Since then the fraction of Birchtree ore has increased to 50%. A reduction of the MgO in concentrate to less than 3% in the total mill concentrate was required to allow safe and economic smelter operation.In October of 2002 a miniplant was set up to simulate the Birchtree plant circuit. Several flow sheet modifications were tested that led to a proposal for a circuit having increased cleaning capacity for the scavenger concentrate and a recleaner on this concentrate. Addition of CMC in rougher cleaner feed was also found to be required. The solution was confirmed through pilot plant testing in the mill in December of 2002. A full-scale installation was designed, engineered, and installed between February and September of 2003 with commissioning in September and October of 2003. Target metallurgy was achieved one week after start-up on slurry to coincide with the Birchtree Mine tonnage increase. This paper highlights the development, design and commissioning stages of the project.The new MgO rejection circuit has successfully allowed the processing of Birchtree ores producing concentrate consistently below 3% MgO. In addition, the new circuit increased overall nickel recovery in the mill.INTRODUCTIONThe Thompson Nickel Belt located approximately 700km north of Winnipeg was discovered in the early 1950’s. Inco first produced nickel from the area in 1960. Over the years the mill has processed several ores from different ore bodies in the area. Currently the Thompson Mill processes two significantly different ores from two mines, Thompson and Birchtree. The Thompson ore is a massive sulphide orebody hosted in schist, containing feldspars, quartz and biotite. Thompson Ore is characterized by high nickel recoveries and clean, low MgO containing concentrates (<2.5% MgO). The Birchtree ore is ultramafic and contains a high percentage of Mg-silicates such as serpentine, chlorite, biotite, amphiboles and talc. Some of these Mg-silicates report to the nickel concentrate and prior to commissioning of the MgO rejection circuit the Birchtree nickel concentrate typically contained 5-8% MgO"

Jan 1, 2006

By M. J. McLeod, D. R. Lux, R. P. Taylor

"The Mount Douglas Granite constitutes the eastern part of the Saint George Batholith and contains the youngest, most differentiated phases of the batholith. It also contains extensive endogranitic, low-grade. Sn- W-Mo-bearing sheeted vein systems. Early phases of the Mount Douglas Granite are coarse- to medium-grained, seriate granites that represent the slowly cooled carapace of the intrusion. Late phases are medium- to fine-grained, equigranular and porphyritic granites that were accompanied by repeated and widespread fracturing of the carapace and injection of mineralizing fluids. These granites represent a highly differentiated suite with ""A "" type affinities developed in a ""within plate"" transitional to ""syn-collision"" tectonic setting. 4oAr/ 39Ar dates for biotites from the various phases indicate emplacement circa 367 Ma.The linear distribution of some phases in the Mount Douglas Granite and the systematic orientations of sheeted veins along tensional fractures indicate structural control on granite emplacement and vein distribution. This type of relatively passive endogranitic mineralization is unique in the granites of southern New Brunswick and contrasts markedly with highly fluidized systems operative elsewhere in the area. IntroductionInvestigation of Sn-W-Mo occurrences in New Brunswick has shown that most of this mineralization is associated with late, highly differentiated phases of post-orogenic (Acadian) granitoid magmatism that occurred during Devonian and Early Carboniferous time (Ruitenberg and Fyffe, 1982; Taylor et al., 1988). The polymetallic Mount Pleasant Sn-W-Mo deposit (Ruitenberg, 1967, 1972; Kooiman et al., 1986)and the Burnt Hill W deposit are two orebodies of this type in New Brunswick. Numerous smaller deposits associated with these granitoid rocks in southwestern New Brunswick have been documented in previous investigations (Ruitenberg, 1967, 1968; Ruitenberg and Fyffe, 1982; Taylor et al., 1985; Lentz, 1985)."

Jan 1, 1988

By K. Sasaki

Ventilation measurements were carried out in a shallow underground-quarry space with relatively large internal volume of 14,600 m3 in order to evaluate its effective ventilation characteristics. Based on air velocity measurements with an ultrasonic anemometer in the exhaust airway connected to the space, it was found that the space was ventilated by natural ventilation airflow with intermittent changes in direction. It was difficult to measure the ventilation flow with typical methods of flow measurement provided from the intake portal and throughout the mine, because the cross-sectional area and volume of the openings were too large and the flow was variable. In the present study, a tracer gas method was applied to evaluate the effective ventilation airflow rate in the space. A photo-acoustic infra-red gas monitor, highly sensitive to SF6 gas used as a tracer gas, was set in the space to determine air exchange rates from gas concentration-time decay curves. The seasonal variations of airflow and thermal environment in the space were investigated through 13 sets of measurements taken over 15 months. Airborne rock dust concentrations were also measured at same time in the opening. The correlations between the effective ventilation airflow rate, thermal environment and dust concentrations in the opening space were analyzed and are discussed based on the presented measurements taken during year. It is concluded that seasonal variations in effective ventilation flow and the dust concentration are mainly due to differences in air temperature in the space, as affected by the rock?s surface temperature and atmospheric temperature. In summertime, the air temperature and associated air density difference generated lower natural ventilation flows resulting in higher dust concentrations.

Aug 1, 2013

Stress induced, gravity-assisted failure processes typically dominate long before stress levels approach the strength of the intact rock (at approximately smax > 0.4UCS where smax = 3s1 ? s3 and UCS is the Unconfined Compressive Strength of the intact rock (Martin et al. 1999)). Under these conditions, discontinuities typically become clamped and the failure process becomes brittle. This brittle failure process is dominated by new stress induced fractures growing subparallel to the excavation boundary. While it is possible to identify areas with the potential for brittle failure, for example, using the general assumption that brittle failure will occur in areas at right angles to the major principal stress (Hoek et al., 1995), when the threshold smax > 0.4UCS is reached in areas around the tunnel boundary, or elastic modelling and the Hoek-Brown brittle parameters proposed by Martin et al., (1999) (i.e. m? 0 and s ? 0.11), amongst others, recent observations discussed by Everitt & Lajtai (2004), and Kaiser (2005; 2006) suggest that brittle failure processes are enhanced when structural features such as joints, weakness zones, bedding planes or foliations are preferentially orientated around the excavation boundary creating stress raisers which in turn facilitate the stress-driven rock mass disintegration process (e.g., as illustrated by Everitt & Lajtai (2004) on Figure 1b). Such weaknesses induce stress heterogeneities that thus promote tensile-spalling failure processes (Diederichs 2000). The observations suggest that stress induced damage can occur ?prematurely? depending on the orientation of micro and macro structures in situations where the known stress conditions should not yet initiate brittle failure processes. In general, when structural features (micro and/or macro), especially foliations, are present in a rock mass, the strength is effectively reduced, largely due to tensile strength heterogeneity in areas depending on the orientation of the structural features with respect to the excavation boundary. As a result, stress induced damage could occur in areas not normally considered due to the influence of anisotropy (Figure 1).

May 1, 2009

By N. I. Basuki, E. T. C. Spooner

"Abstract - More than 2800 published fluid inclusion data (primary inclusions) from eighteen typical Mississippi Valley-type (MVT) Zn-Pb deposits and districts were examined to study possible relationships between MVT fluid properties and metal tonnages and ore grades. The mean Th and salinity values for fifteen MVT deposits and districts are 122°C ± 21°C and 20.7 ± 2.6 wt% CaCl2 equivalent, respectively. In general, temperatures increase from pre-ore to ore stages, and salinities decrease from ore to post-ore stages. From post-ore to late calcite stages, salinity and temperature decrease with various trends within specific districts.Several conclusions are drawn: first, results show that Hanor’s (1996) salinity threshold for metalrich basinal fluids applies to typical MVT ore fluids (~16 wt% CaCl2 equivalent). Second, the lower limit of mean Th values of measured MVT deposits and districts (n = 15) of ~75°C is similar to Hanor’s (1996) observed temperature threshold for metal-rich basinal brines of ~60°C (n = 224). Third, there is no statistically significant relationship between fluid inclusion homogenization temperatures (Th) and metal tonnages or ore grades. Fourth, there seems to be a tendency for large tonnage districts/deposits to be associated with mean fluid salinities that are relatively low (~16 to 21 wt% CaCl2 equivalent) within the overall range of salinity means (~16 to 26 wt% CaCl2 equivalent). There is also a correlation between higher ore grades and higher salinities. Finally, comparison with other sedimentary rock-hosted Zn-Pb deposit types shows a trend of salinity decrease and temperature increase from MVT, sandstone-hosted and diapir-related Pb-Zn deposits, to vein-type and Irishtype Pb-Zn deposits, and then to sedex deposits. However, more data are needed for sedex deposits. The salinity threshold for significant Zn-Pb transport decreases to =~10 wt% CaCl2 equivalent at ~250°C. This study suggests that fluid inclusion analysis during exploration may be useful in assessing ore-forming potential (threshold salinity) and possible ore grades (salinity)."

Jan 1, 2002

By R. R. Rogers

Introduction The subject of cathodic protection is not new. In 1824 Sir Humphry Davy, in publishing the results of his investigations for the British navy, pointed out that copper could be protected from sea-water corrosion by connecting it electrically with zinc or iron. Since that time much work has been clone in this field, particularly in the protection of metals from the action of sea water, neutral brines, and treated and untreated waters. Special mention should be made of the successful protection of underground pipe-lines which formerly were badly corroded by the water in the ground. So far, magnesium alloy and zinc anodes have been the most popular. However, fairly recent work has indicated that aluminium anodes will give good service under certain conditions. The principle of cathodic protection has been applied extensively in coating steel articles with zinc and in cladding aluminium alloy sheet with pure aluminium. A valuable discussion of the fundamentals and applications of cathodic protection recently was presented in the Corrosion Handbook. A useful list of references was included in the article.

Jan 1, 1949

By C. W. Eggert

This paper gives an account of the E.V.O.P. tests made at the Copper Rand mill of the Patino Mining Corporation in Chibougamau, Quebec. The runs were made to acquire an understanding of the method. A description of events, along with conclusions, observations and opinions, is out-lined.

Jan 1, 1967

By H. Blaha, H. Wagner

"Room and pillar workings in salt mines are preferred sites for underground waste disposal. A critical issue in selecting waste disposal sites is long-term behaviour of such workings. The long-term behaviour of salt pillars is controlled by the pillar geometry, i.e. the height, width and length of pillars and the level of pillar stress. The latter has a strong influence on creep characteristics of salt pillars whereas the width to height ratio of salt pillars determines the strength of pillars and the deformation characteristics of salt pillars.Three different regimes of pillar creep behaviour of salt pillars can be distinguished, namely a stress level below which the rate of creep approaches a value of zero, a stress range where the rate of creep is constant and finally a stress level above which the rate of creep accelerates. Long-term stability of room and pillar workings can be assured only when the pillar stress level falls within the first stress regime. Strength and creep tests on model salt pillars have shown that at stress levels below 40% of pillar strength the rate of creep approaches a value of zero, between stress levels of 40% and 65% the rate of creep is constant but increases with stress level. Above pillar stress levels of 65% the rate of creep accelerates.Long-term measurements of pillar deformation and surface subsidence above relatively shallow room and pillar workings in salt mines have confirmed these observations. Long-term strength of salt was found that be between 60% and 65% of short term strength. The evaluation of salt pillar behaviour on the basis of critical pillar stress levels was found to be superior to the traditional factor of safety concept because it allows relating pillar deformation measurements to actual pillar conditions. The approach described in the paper was used successfully to evaluate the stability of room and pillar workings in a salt mine and to design strategies to stabilise critical pillar workings."

Jan 1, 2015

By Jaeheon Lee, Junmo Ahn, Isabel F. Barton

"Newmont’s Mike prospect, currently undeveloped, is a blind Cu-Au(-Zn) deposit on the Carlin Trend, containing >8.5 M oz. Au, 1027 M lbs. Cu, and 809 M lbs. Zn as Carlin-type gold and polymetallic Cu-Zn minerals in Paleozoic lower-plate carbonates and shales. This project was undertaken 1) to examine the effectiveness of different lixiviants for leaching the Mike supergene Cu-Au ores via bottle roll tests, and 2) to determine what ore minerals resist dissolution in each leaching agent by comparing the mineralogy and chemistry of head and tail samples. Sulfuric and sulfurous acids were used to leach copper and cyanide was used to leach gold. Thiourea, glycine, and other lixiviants were used to leach both base metals and precious metal. QEMSCAN and SEM study of six samples of different ore types and grades indicate that the Au occurs as varieties of native gold, including auricupride and electrum. Major Cu minerals are native Cu, cuprite, malachite, chrysocolla, and conichalcite (Ca-Cu arsenate), with locally significant Cu in jarosite and goethite. Gangue mineralogy is dominated by quartz, sericite, chlorite, alunite, smectite and kaolinite, K-feldspar, and iron oxides (sensu lato). Results of bottle roll tests and leach residue mineralogy will be presented and discussed at the conference.INTRODUCTION Resource and Geologic Setting The Mike deposit is a large, blind Cu-Au(-Zn) deposit in the Maggie Creek district of the Carlin Trend of Nevada, USA, near the Gold Quarry mine (Figure 1). The mineral inventory, based on drilling, is 8.568 Moz. Au, 1027 M lbs. Cu, and 809 M lbs. Zn at average grades of 0.72 g/t Au, 0.34 wt% Cu, and 2.13 wt% Zn (inventory for a cone at $400/oz Au and $0.80/lb Cu by Norby and Orobona, 2002)."

Jan 1, 2017

By M. D. Johnson, R. K. Bezys

"The majority of Ontario&apos;s limestone and dolostone production comes from a few Paleozoic carbonate units. In eastern and central Ontario, Ordovician rock units, which are the main sources for production, include the Oxford, Gull River, Bobcaygeon, Verulam, and Lindsay Formations. They are predominantly utilized for aggregate and cement manufacturing, with the Bobcaygeon Formation being used as a source of building stone. Along the Niagara Escarpment, the Silurian Lockport, Amabel, and Guelph Formations are sources for the limestone industry. The largest tonnage of rock extracted by the industry comes from these Silurian units, especially the Lockport and Amabel Formations. These units are used primarily for aggregate, although they are also a source for lime. In southwestern Ontario, the Silurian Bertie Formation and Devonian strata, represented by the Bois Blanc Formation, Onondaga Formation, Detroit River Group, and Dundee Formation, contribute to Ontario&apos;s production of lime, cement production and crushed stone. The Detroit River Group (Lucas and Amherstburg Formations) is the main source of the lime and cement produced in the province.Northern areas, which may become significant sources for the industry, include Manitoulin Island, the Lake Timiskaming area, and the James Bay Lowland. IntroductionThe Engineering and Terrain Geology Section of the Ontario Geological Survey has undertaken a geological inventory of all active and abandoned limestone and dolostone quarries in Ontario. This geological study, combined with a commercial study of active quarries carried out by the consulting firm of Derry, Michener, Booth and Wahl, will provide an up-to-date report on the industry in the province and will be published by the Aggregate Resources Section of the Ministry of Natural Resources. This report will follow the format and style of D.F. Hewitt&apos;s Ontario Department of Mines Industrial Mineral Reports and Circulars (Hewitt, 1960, I964a, 1964b, 1964c; Hewitt and Vos, 1972). Examinations of the quarries were carried out by geologists in the Paleozoic I Mesozoic Geology Subsection of the Engineering and Terrain Geology Section, and include, in addition to the authors, R,R. Wolf, V.A . Mazur, and D.K. Armstrong in the summer of 1986."

Jan 1, 1988

By Pierre Montrueil, Marcel St-Amant

Within the next few years, underground mobile equipment will be partially automated. Mining methods will integrate more and more automation. Such an evolution will be possible only if adequate underground communication systems are developed. This is expected due to the available competence in Canadian telecommunication, to the economic pressure on the Canadian mining industries for international competitiveness and to the social changes where a better working environment (i.e. less accidents) becomes a major concern. CCARM propose the concept of a Production Area Network for Automated Mobile Units called PANAMU as an intermediate size communication system. It can be implemented using mature present-day technology and it can be integrated in some mine wide communication systems. It can evolve so as to incorporate new technologies because of its modular concepts. In this paper, the communication requirements are estimated, the amtmptions are defined, the concepts of the PANAMU are presented and an over- view of its implementation is described. CCARM presents this article to the mining industry as a document for discussion.

Jan 1, 1994

By Dan Marshall, David H. Watkinson

Abstract - Cobalt, Ontario, is renowned for the 12.6 billion grams (445 million ounces) of silver produced from the area since discovery in 1903 by workers of the Timiskaming and Northern Ontario Railway. Native silver generally occurs with cobalt arsenides and sulfosalts in near-vertical carbonate veins cutting the Huronian sedimentary rocks of the Gowganda Formation, the Archean metavolcanics and/or the Nipissing diabase. All major deposits have been found within a few hundred meters of the unconformity between the Archean and Huronian rocks in general proximity to the Nipissing diabase and volcanogenic sulfide mounds within the Archean meta-volcanics. Silver has been mobilized from one or more of the local country rocks by hyper-saline brines and deposited in or near zones of mixing where the saline brines encounter paleometeoric water transported to depth along the unconformity or local structures. Previous work has shown that chloride complexes are the dominant ligands responsible for silver transport. These hypersaline brines, represented as halite-bearing fluid inclusions at room temperature, have been trapped as primary fluid inclusions within vein minerals. Pressure-temperature conditions of vein formation have been derived from mineral equilibria, maximum lithostat and fluid-inclusion studies. These data are consistent with vein formation occurring over the temperature range 300°C to 350°C, with pressures constrained between 60 Mpa and 136 Mpa (600 bars and 1360 bars).

Jan 1, 2000

By P. Mark. Hawley

Development of Barrick Gold?s Pierina Gold Mine in north-central Peru requires construction of a waste dump for disposal of non-ore grade materials stripped from the open pit to expose the ore. The waste dump site is located near the open pit in a U-shaped valley that is underlain by thin colluvial and morainal soils with locally thick peats and glaciolacustrine deposits. Bedrock underlying the site consists of variably weathered volcanics. The site is subject to moderately high seasonal rainfall and significant seismicity. The geotechnical quality of the waste rock is highly variable, ranging from low quality, degradable, soil-like materials containing appreciable quantities of silt and clay, to high quality, hard, durable, blocky waste rock. A hybrid dump design concept was developed that requires in-pit segregation of high and low quality waste, and selective placement of materials in the dump to maximize stability and enhance internal and subsurface drainage. The design includes a rock drain beneath the dump along the axis of the valley and a series of connected finger drains. Extensive peripheral diversions and stormwater control measures to inhibit infiltration of precipitation are also included. This paper discusses the unique challenges presented by the site and waste materials, the design methodology and stability analyses, and planned monitoring systems.

May 1, 2002

By K. Zenger, J. Kaartinen, J. Huuskonen, S. Torttila, S. Lähteenmäki, J. Pietilä

"Pyhäsalmi Mine in Finland has a long history of continuous process development. The concentrator processes Cu-Zn-sulphide ore with high recoveries. An on-line flotation simulator has been developed to maintain and further improve the flotation performance. Consisting of a flotation kinetic dynamic model, and interconnected with process control software, the simulator can be used for training new control room operators in various scenarios. For daily operation, the model parameters are continuously adapted to take into account the changing process conditions. On-line simulator tracking the process can provide the process operator new information in several ways: a) values of unmeasured process variables are obtained by displaying the corresponding simulator values, b) predictions of future process states and outputs are calculated and displayed, c) information of changing process parameters can be used as an indicator of e.g. change in the processed ore type. This paper describes the adaptive simulation system and its usage at the Pyhäsalmi concentrator.IntroductionPyhäsalmi massive sulphide orebody is located in central Finland. Operation of the mine started in 1962 and it is currently producing copper (Cu), zinc (Zn) and sulphur (S) concentrates. The concentrator control and optimization system has a long history of successful continuous development during the past decades (see e.g. Huuskonen & Moilanen, 2010). An on-stream analyzer has been a part of the automatic process control since 1968 (Lähteenmäki, Miettunen & Saloheimo, 1999). First control algorithms based on a flotation mathematical model were developed in 1971 (Koivistoinen & Miettunen, 1985). In 1990’s the development of a froth machine vision systems started (Kaartinen, 2009; Kaartinen, Roine & Hätönen, 2009). More recently Pyhäsalmi Mine Oy has been involved with several national development projects dealing with particle size distribution measurements (Kaartinen & Tolonen, 2008), spectral analysis of flotation slurries (Haavisto, Kaartinen & Hyötyniemi, 2008), and dynamic simulation of flotation processes. The latter topic is further elaborated in this paper."

Jan 1, 2015