Search Documents

By Samantha Beeson, Collin Poole

"This paper examines the development of two new selective flocculation techniques for recovering KCI values from low grade carnallite potash ore.Direct recovery of KCI was achieved using one of two mid-range molecular weight polymers, one non-ionic and the other strongly cationic, in conjunction with the same selective anionic dispersant. From initial response studies on pure minerals and selective flocculation tests on synthetic mixtures, investigations were extended to recover KCI values from a natural carnallite potash ore. A single-stage process achieved products grading up to 61.3% KCI at recoveries up to 85.4% for the cationic flocculant suite and up to 64.8% KCI with recoveries as high as 90.3% for the non-ionic flocculant suite, with dispersant and flocculant dosages of 150-250gr1 and 10-75gr1, respectively. These results clearly demonstrate not only the feasibility of treating such problematic ores at low reagent dosages, but also the potential elimination of desliming prior to froth flotation.The experimental results presented are considered in terms of the reagent adsorption phenomena present in the system and various aspects of floe formation and cleaning.IntroductionAs high-grade sylvinite potash ores become scarce, lower grade sylvinite and carnallite potash ores are becoming more attractive. However, these ores often contain large amounts (up to 15% by weight) of water-insoluble slimes which must be removed prior to KC! flotation, owing to their high adsorptive capacity for the amine collectors used. The slimes are generally removed by scrubbing followed by hydroclassification and any residual material not eliminated is blinded with reagents such as guar gum or starch to inhibit interference in subsequent KC1 flotation.An alternative approach used commercially in Canada by Agrium Inc. involves water-insoluble slimes flotation prior to KC! flotation. In this process, the slimes are selectively flocculated and then separated by froth flotation. Losses of KC! to the slimes product and associated brine requirements are both reported to be less than those encountered in conventional desliming, but the technique is somewhat limited in its application at present."

Jan 1, 1997

By F. Guo

"The leaching kinetics of zinc sulphide concentrate was studied under total pressures ranging from 0.3 MPa to 0.5 MPa and leaching temperatures ranging from 358 K to 378 K. The apparent activation energy of leaching reaction under different total pressures was calculated. The results show that for the extraction of zinc at low-temperature pressure leaching is controlled by an interfacial chemical reaction. This was supported mineralogical analysis of the leaching residue. The kinetic equation for low-temperature pressure leaching of zinc sulphide concentrate was further established by quadratic regression on the basis of shrinking core model.INTRODUCTIONThe Roast-Leach-Electrowinning Process (RLE) is the primary route for zinc production and responsible for more than 85% of the total zinc production (Souza et al., 2007). During the roasting of zinc concentrates, fugitive SO2 causes pollution. The prevention of SO2 emissions from the RLE process can be one of the challenges to this technology (Deller, 2005). In the 1980s, the Zinc Pressure Leach (ZPL) process changed the concept of zinc hydrometallurgy, in which zinc sulphide concentrate is directly leached at approximately 423 K and approximately 0.7 MPa oxygen overpressure and the sulphidic sulphur is oxidized into elemental sulphur so that the pollution by SO2 is completely avoided. Since 1981, five zinc plants have adopted the ZPL process either for expansion by integration with existing roasting facilities, or for the production of zinc without any roasting at all (Collins et al. 1994; Barth et al. 1998). The innovation of the ZPL process has made the zinc industries more competitive although it needs an autoclave. The direct leaching technology of zinc is still in development."

Jan 1, 2012

By W. F. James

"The property of Siscoe Gold Mines, Limited, comprises about 1,600 acres, including Siscoe island and adjacent claims under water in Montigny lake, in Dubuisson and Vassan townships, Quebec.For many years the property was reached by way of Harricana river and its chain of lakes from Amos, Quebec, about 45 miles distant. In later years a highway has been built from Noranda east through Val d'Or, about 5 miles distant.Gold was discovered on one of the claims on the north shore of Montigny lake as early as 1911, but these gold discoveries have never been economically important. Several years later gold was discovered on Siscoe island and considerable surface work was carried out. Still later, iscoe Gold Mines, Limited, was formed and carried out further work, some of it through shallow shafts. In 1928, larger scale operations were undertaken and a 100-ton mill was constructed. In the years following, production· was on a larger scale with lower grade, until finally a milling rate of over 1,000 tons a day was attained. Approximately 1,500,000 tons were treated between the end of 1940 and mid-year 1945. At present the milling rate is down to about 200 tons a day and work is confined chiefly to some of the less important veins that have been recently developed.The following is a summary of production up to December 31st, 1946:"

Jan 1, 1954

By T. Yalcin

"This paper describes the development of a mathematical model for determining the liberation of an ore at various grinding sizes, based on the combined results of microscopic counting, grinding tests, and chemical analysis.The method is illustrated with an application to the magnetite ore of Sherman Mine in Temagomi, Ontario. For this ore, a degree of liberation of 98.7% was determined at a grinding size of 90% passing 44 microns, which closely corresponds to the final grinding size employed at the Sherman Mine Concentrator.Introduction Liberation characteristic of ores have direct and significant bearing on overall economics of concentration processes.Target grades and recoveries can be achieved only it minerals are adequately liberated prior to separation. Degree of liberation depends on the extent of size reduction. However, due to the high costs associated with size reduction processes, it is important to keep size reductions within limits of satisfactory liberation. Prevention of excessive size reduction is also necessary because of inefficient mineral separations in very fine sizes. Hence, a study of reduction size — liberation relationship is essential for optimum profit from milling operations.A number of procedures have been developed for liberation studies (1-12), but there is lack of method for universal adoption.A new approach is presented in this paper that might provide a realistic estimate of liberation and give a practical guidance as to the degree of size reduction required for satisfactory liberation."

Jan 1, 1985

By John A. Herbst, Gerald H. Luttrell, Jaisen N. Kohmuench, Aaron Noble, Michael J. Mankosa

The HydroFloat TM is an innovative fluidized-bed separator that can substantially increase the upper particle size that can be successfully treated by flotation. Recent studies conducted using laboratory, bench-scale and pilot-scale equipment indicate that this technology can be used to float coarse sulfide middlings that cannot be recovered by conventional flotation machines. Recent data collected from pilotscale tests conducted at a base metal concentrator indicate that this technology can float middlings particles as large as 850 microns in diameter containing as little as 1% exposed hydrophobic mineral. As such, the crossover of this technology into the base metals industry has the potential to substantially reduce grinding costs and increase concentrator recovery/capacity through the use of split-feed circuitry. The split-feed concept, which is often used for upgrading industrial minerals, involves segregation of the feed into more than one size class followed by subsequent upgrading using mills/separators/reagents specifically optimized for each size class. In this article, a split-feed circuit is described that utilizes two stages of classifying cyclones in conjunction with the HydroFloat_ separator. The circuit is designed to recover, recycle and regrind coarse middlings containing small amounts of valuable mineral while simultaneously rejecting coarse well-liberated siliceous gangue so that mill throughput can be increased. Simulation data conducted using well-known process models suggest that this approach can increase existing primary mill capacity by up to 25% with only modest investments in new classifying and flotation equipment.

Jan 1, 2016

By M. Rantapaa

Measurable improvements in throughput have been documented at Barrick Goldstrike due to increased ore fragmentation through efficient drilling and blasting techniques. A decrease in throughput at the autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the open pit and process areas worked closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of actually improving throughput in future years, despite the projected harder ores. A series of tests were conducted to determine if adjustments to drilling and blasting could positively influence throughput. Better fragmentation and a subsequent increase in mill throughput were achieved through the use of electronic caps for more precision and flexibility, as well as for allowing extremely fast shots; explosives with a higher velocity of detonation (VOD) to provide for improved shock energy; and improved distribution of the explosives by decreasing pattern spacing. Early tests indicated a significant increase in throughput when processing identified harder ore. It is anticipated that the total process throughput (hard and soft ore) will increase by 6 tph in 2003 due to the improved fragmentation of the hard ore. Barrick Goldstrike?s D2M initiative includes roaster hard ore (BWI>17), as well as autoclave hard ore (BWI>15). Approximately 6 million tons of D2M material were shot in 2003, a relatively small amount compared to the 150 million tons to be mined. The benefit of additional ounces produced should far outweigh the additional drilling and blasting costs.

Jan 1, 2005

By R. Mckinstry, M. Rantapaa, T. Bolles

"Measurable improvements in throughput have been documented at Barrick Goldstrike due to increased ore fragmentation through efficient drilling and blasting techniques. A decrease in throughput at the autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the open pit and process areas worked closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of actually improving throughput in future years, despite the projected harder ores. A series of tests were conducted to determine if adjustments to drilling and blasting could positively influence throughput.Better fragmentation and a subsequent increase in mill throughput were achieved through the use of electronic caps for more precision and flexibility, as well as for allowing extremely fast shots; explosives with a higher velocity of detonation (VOD) to provide for improved shock energy; and improved distribution of the explosives by decreasing pattern spacing. Early tests indicated a significant increase in throughput when processing identified harder ore. It is anticipated that the total process throughput (hard and soft ore) will increase by 6 tph in 2003 due to the improved fragmentation of the hard ore.Barrick Goldstrike’s D2M initiative includes roaster hard ore (BWI>17), as well as autoclave hard ore (BWI>15). Approximately 6 million tons of D2M material were shot in 2003, a relatively small amount compared to the 150 million tons to be mined. The benefit of additional ounces produced should far outweigh the additional drilling and blasting costs."

Jan 1, 2005

By K. Soucek, J. Ptácek, A. Hastíková, R. Kukutsch, P. Konícek, P. Waclawik

"Cable bolts are used frequently as a secondary support system (with steel arch support) in difficult stress-strain conditions of deep coal mines. The load transfer mechanism of cable bolts depends on several factors, such as the strength, deformation and geometric properties of the bolts, resin and the surrounding rock mass so-called cable-resin-rock system (CRR system). The bonding length and bolt/borehole diameter ratio strongly influence the final bearing capacity of the CRR system.The study presents the behaviour of CRR system during a pull-out test which is usually used in the carboniferous rock mass in the Czech part of the Upper Silesian Coal Basin. A series of 28 pull out tests were performed on 3-m-long cable bolts, with various combinations of borehole diameters and bonding lengths, to understand this behaviour. Boreholes were drilled into a solid rock mass consisting of fine-grained sandstone to guarantee similar conditions during the pull-out tests. Video inspection and measurement of borehole diameters were performed to determine their quality and real diameters. Three characteristics were observed from pull-out test results: ultimate pull-out load; displacement of the end of bolt and system stiffness. Numerical modelling by FEM (Finite Element Method) was used to determine the stiffness of the CRR system for variable bolt/borehole ratios and bonding lengths each under constant load. A linear elasto-plastic model and a mohr-coulomb model were used for cable and resin-rock respectively. The results of the experiment may contribute significantly to improving of the methodology of cable bolts installation as well as the design of used cable bolts."

Jan 1, 2015

By George Carico

Research and related demonstration projects are being conducted in West Virginia on both existing and former coal surface mine lands to determine potential post-mine land re-use options that offer the greatest likelihood of future benefit and success. Examples of projects include renewable energy considerations that incorporate solar, wind, and/or biomass options, and contain components designed to educate business, government entities and the local community on renewable energy options and potential opportunities Multiple property re-use options are being researched and evaluated, based on site-specific conditions and characteristics, including infrastructure, local community needs and regional economic conditions. Re-use options being explored include innovative uses and needs, such as specialty housing, unique business and industrial needs, and an extensive variety of recreational and small business opportunities that best fit the specific needs of the local community and regional economic structure.

Aug 1, 2013

By J. A. King, D. A. Knight

"The Porgera orebody is located in mountainous terrain in Enga Province, Papua New Guinea. An underground mine has been developed which produces up to 2000 t/d of ore grading over 2 ozs Au/t. Some 79% of the gold in the ore is free, with the balance in a highly refractory form as sub-microscopic gold evenly disseminated within a pyrite matrix.This paper describes the metallurgical plant that uses flotation and cyanidation circuits to effectively recover the free gold in the ore feed, allowing for wide variation in the gold head grade. The refractory gold component in the ore is stored as leached pyrite flotation concentrate and this concentrate will be later treated by autoclaving techniques to recover the contained gold.The ProiectThe property is located in the Porgera Valley 600 Km North West of Port Moresby. The remote location is 2500 m above sea level. The mine area has 3600 mm of annual rainfall and a temperate climate with temperatures ranging from 10° c to 22° c throughout the year.Alluvial gold was reported in the Porgera area in 1938 and has been an important source of revenue for the area for many years. Intermittent exploration was carried out until the 1960 1 s when Placer (PNG) Pty. Ltd. with Mt. Isa Mines commenced an extensive exploration program. The property was brought to production in 1990 by the Porgera Joint Venture group consisting of Mount Isa Mines Ltd, Rennison Goldfield Consolidated Ltd. and Placer Dome Inc, each with a 30% ownership and the Government of Papua New Guinea with a 10% share. Placer Dome Inc. is the manager of the property with construction under the direction of the Placer Dome Technical Services group."

Jan 1, 1992

By M. -C. Noël, G. P. Demopoulos

In this work the formation and environmental stabilization potential of arsenate-containing fluoroapatites is considered. In particular in this research various compounds were precipitated from synthetic solutions containing fluoride, arsenate/phosphate and calcium by varying different parameters-temperature, Ca:As ratio, pH, and P:As ratio, and aging time. The results obtained helped determine the operating window that should be used for the formation of highly crystalline fluoroapatites, in particular svabite (Ca5(AsO4)3F). It was found that svabite has a specific pH range of precipitation, with lower pH yielding CaF2 and calcium arsenate compounds such as CaHAsO4•H2O. At higher pH, a mixture of svabite and johnbaumite (Ca5(AsO4)3OH) precipitated, yielding a less stable material. This range of precipitation varied with the concentration of arsenic in the starting solution, and widened with higher initial concentrations of Ca2+, AsO4 3- and F-. Furthermore, svabite/fluoroapatite solid solutions were formed by using the same procedure as svabite but replacing some of the arsenate in solution by phosphate. The increase in phosphate content yielded a gradual change in morphology and crystallinity. Work on stability evaluation is currently under way.

Jan 1, 2014

By Ali Bunjaku, Lauri Pesonen, Hannu Johto

It is well known that there are many ways to process copper concentrates into copper anodes using the pyrometallurgical route. All modern copper smelting technologies are fundamentally energy efficient and environmentally safe options, and therefore choosing one depends on the desired capacity range, feed impurity levels, plant location, flexibility needs, overall energy use, and of course smelter economics in both the short and long term. This paper focuses on comparing different solutions which have potentially the lowest variable opex (operational expense), meaning in practice finding out which technology offers the best chances for profit maximization under certain scenarios. For the comparison, we chose to have a closer look at Outotec Flash Smelting (FSF) – Peirce-Smith Converting (PSC), Outotec Flash Smelting (FSF) – Outotec- Kennecott Flash Converting (FCF), Outotec Ausmelt TSL Smelting (ASF) - Peirce-Smith Converting (PSC), Outotec Ausmelt TSL Smelting (ASF) - Outotec Ausmelt TSL Converting (ACF), Mitsubishi Smelting Process (MIT), Bottom Blowing Reactor (BBR) – Bottom Blowing Continuous Converting (BCC), and Side Blowing Furnace (SBF) - Top Blowing Converting (TBC) since these seem to be the main state-of-art technologies now being applied in many recent copper smelter projects around the world. The work was carried out by modelling each smelting route by using the new HSC SIM 9 simulation software and applying operation time, energy, and consumables consumption numbers for each unit process and stream. Combined with cost data, the exercise produced a rich set of information which will be shown in detail for each area per scenario. The authors’ goal here was to provide a fair comparison where each technology can be evaluated from various perspectives such as electricity use or refractory consumption. INTRODUCTION Copper can be produced either pyrometallurgically or hydrometallurgically. The hydrometallurgical route is used only for a limited amount of the world’s copper production (~20%) and is normally only considered in connection with in-situ leaching of copper ores. On the other hand, most of the copper extraction from Cu-Fe-S minerals is pyrometallurgical (~80%) (Schlesinger 2011, ICSG 2017). Thus, several different processes can be applied for copper production, including the following state-of-the-art technologies: Outotec Flash Smelting (FSF) – Outotec-Kennecott Flash Converting (FCF) Outotec Flash Smelting (FSF) – Peirce-Smith Converting (PSC) Outotec Ausmelt TSL Smelting (ASF) - Peirce-Smith Converting (PSC) Outotec Ausmelt TSL Smelting (ASF) - Outotec Ausmelt TSL Converting (ACF) Mitsubishi Smelting Process (MIT) Bottom Blowing Reactor (BBR) – Bottom Blowing Continuous Converting (BCC) Side Blowing Furnace (SBF) - Top Blowing Converting (TBC)

Jan 1, 2019

By D. Bouchard, M. Forté, A. Charette

A transparent replica of a casting die was built to achieve a better understanding of the filling mechanisms of aluminum in high pressure die casting. Water and tomato paste were respectively used as analogues for the Newtonian liquid aluminum and the non-Newtonian semi-solid aluminum. The transparent die was installed on an industrial casting press and filling was filmed with a high-speed camera. Differences between the Newtonian and non-Newtonian fluids are presented and discussed.

Jan 1, 2006

By Ken Steele, Pam Sangster, Myra Gerow

Ontario leads Canada in production of structural materials and ranks third in production of non-metallic minerals. The total value of industrial mineral production in 1997 was $1.6 billion. The province is the leading producer of nepheline syenite, salt, talc, clay products, cement, lime, sand and gravel, stone and a major producer of gypsum and silica. Barite, sulphur in smelter gas, elemental sulphur, tremolite, serpentine, gemstones and peat are also produced. Table 1 shows recent actual industrial mineral production levels in Ontario. Other industrial minerals, including phosphate, petalite, diamonds, wollastonite, vermiculite, kyanite, garnet, graphite, silica, kaolin, dimension stone and anorthosite, have been the target of exploration and development projects. Investment opportunities exist at all levels from grass-root prospect through to production level.

Jan 1, 2001

By K. Yamaguchi, Sekimoto. H.

"Platinum Group Metals (PGMs) used as catalyst which reduces toxic substances in emission gas exhausted from an automobile should extensively be recycled because they are rare metals produced only at the limited regions. The recycling process is to smelt an alumina honeycomb, in which PGM is built, in molten iron with flux such as lime and silica to separate them. PGMs are concentrated in molten iron while alumina in slag.The objective of this study is to understand the factor to concentrate PGMs in liquid iron as much as possible. Fundamental research of the distribution of the PGMs between the slag and liquid iron was carried out to recover the value metals of platinum, palladium and rhodium from the three-way auto catalyst. The distribution ratios of platinum, palladium and rhodium between the Al2O3-CaO-SiO2 slag and liquid iron are from 10-6 to 10-5, and these are concentrated in comparison with slag phase by about 1 million times to the liquid iron at 1873 K. The distribution ratios of platinum between the FexO-CaO-SiO2 slag and liquid iron decrease from 0.1 to 2?10-4 with increasing the CaO content in the slag. The CaO addition to the FexO unary slag is effective in concentrating platinum in molten iron.Based on the distribution ratios obtained in this work, recovery of PGMs was determined. The recovery of platinum, palladium and rhodium increase with increasing the mass ratio, Mmetal/Mslag. In the case of the conditions of Mmetal/Mslag = 0.04, the recoveries of PGMs showed more than 99.97%. The use of liquid iron and carbon saturated liquid iron as the collector metal is advantageous for the PGM recycling of the three-way auto catalyst. We found that PGMs are enriched to the molten iron or the carbon saturated iron and the slag loss of PGMs is negligible small."

Jan 1, 2014

By J. J. Taute, O. S. Tinkler, G. Zárate, K. C. Sole, J. Steeples

Global practice in copper solvent extraction is reviewed, based on individual plant operating data for 2018. The survey respondents account for almost 40% of global copper cathode production by solvent extraction and electrowinning. Regional trends in operating conditions, as related to the prevailing ore mineralogy, leaching processes, and life of mine are evaluated. The adoption and expansion of this technology in the African Copperbelt and Asia are assessed, together with the associated challenges of specific orebody characteristics. Trends in feed and electrolyte compositions and flow rates, and extractant and diluent selection, together with their impact on copper recovery are reviewed. The evolution of equipment design and associated ancillary processes are discussed, and new projects identified. INTRODUCTION Continuing from similar surveys carried out in 1997, 1999, 2003, 2007, and 2013 (Robinson, Davenport, & Jenkins, 1997; Jenkins, Davenport, Kennedy, & Robinson, 1999; Robinson, Sandoval, & Cook, 2003; Robinson, Moats, Davenport, Karcas, Demetrio, & Domic, 2007; Sole, Zarate, Steeples, Tinkler, & Robinson, 2013), global operating practice in copper solvent extraction (SX) in 2018 is reviewed. Contributing operations include established sites in the USA (8), Chile (9), Peru (2), Spain (1), Mexico (2), and Australia (2), as well as newer operations in Africa (7) and Asia (3). This survey represents 2018 copper cathode production of 1.91 Mt, or about 43% of world production by solvent extraction combined with electrowinning (SX–EW). Trends in operating conditions and performance, as well as equipment design and process technology choices are analysed. The significant expansion in production in the African Copper Belt is also discussed. There are currently about 130 operations worldwide producing some 4.6 Mt copper by SX–EW; of these, about half produced more than 10 000 t/a. Figure 1 shows global copper production by country. As it has for several decades, Chile remains dominant, with 36% of global production of cathode copper. Since 2005, the Democratic Republic of Congo (DRC) has increased production year on year, and now represents 23% of the global total (International Copper Study Group, 2017; Statistica, 2018). Copper production in Asia has grown significantly in the past decade, particularly since the ramp-up of Wanbao in Myanmar. There used to be numerous small copper SX plants in China (Schlesinger, King, Sole, & Davenport, 2011), although most of these have now shut down and Chinese production is lower than it was five years ago. The most important trend, however, is the rise of Chinese-owned mining companies, particularly in Central Africa, but also around the world more generally.

Jan 1, 2019

By Knut F. Garshol

Quality and durability of sprayed concrete depends on the concrete mix design, the type and use of accelerator and all the aspects of the placement onto the rock surface in the underground working. A large number of influence factors are involved and they must be managed for a successful and durable permanent sprayed concrete structure to be produced. The paper discusses some of the central issues, including how to view the long-term effects of chemical admixtures and accelerators in wetmix sprayed concrete. Permanent lining sprayed concrete for rock support is increasingly being used today and the durability can be equally achieved as for any other concrete.

May 1, 2003

By Yves-Laurent Turcotte

Notre conférencier, Monsieur Yves L. Turcotte, Vice-président et Directeur général chez Promaintech Novaxa est diplômé en génie industriel de l?Université du Québec à Trois-Rivières et détient une maîtrise en gestion de projets de l?Université du Québec à Montréal. Il est une véritable sommité canadienne dans le domaine de l?amélioration de la performance des organisations. Provenant d'entreprises manufacturières et de services, il possède plus de 20 ans d?expérience en tant que développeur de technologies, conseiller et formateur auprès d?entreprises. Il a à son actif la réalisation de mandats dans plus de 400 entreprises. Il est reconnu pour sa grande capacité d?analyse et pour trouver des solutions novatrices et profitables aux problèmes des organisations les plus complexes. Aujourd'hui, il dirige Promaintech Novaxa, une division de DMR, qui a célébré son dixième anniversaire en 2006. Cette organisation ayant des places d?affaires dans la région de Montréal, Québec et Vancouver compte plus de 50 professionnels et a une carte de visite dans 16 pays. Les axes d?intervention sont le Management, la Productivité, la Fiabilité, l?Innovation et l?Amélioration Continue.

Feb 1, 2008

By O. G. Olvera, E. Asselin, D. Rival

Particle concentration distributions in a leaching tank have been estimated using a novel experimental approach that takes advantage of the galvanic interactions that occur between pyrite (FeS2) particles and a Pt electrode. The collision of FeS2 particles with Pt changes the open circuit potential measured with the electrode due to galvanic interactions. To discern particle collisions with the Pt electrode from experimental noise a simple analytical procedure was first adopted although the use of techniques involving frequency domain analysis is also briefly presented and discussed. Although this method is still under development, it is simple to implement and can yield valuable information regarding the hydrodynamic behavior of solid particles in stirred tanks in very short times. Finally, the advantages and drawbacks of the technique are discussed.

Jan 1, 2014

By R. Noorani, M. Cai

"Excavation of deep underground openings in highly stressed grounds can generate new fractures near the openings. As a result, rock mass bulking may occur, leading to large wall deformation. A better understanding of brittle rock failure and the associated fracturing process at the laboratory scale is an essential step towards evaluating dilation behavior of rocks. A grain-based model that can capture dilation behavior of rocks under various loading conditions at the laboratory scale can be a useful approach to study rock mass bulking at the field scale. The aim of the paper is to study the dilation behavior of rocks at the laboratory scale employing numerical simulation. A modified grain-based model is used to simulate the macroscopic response of crystalline rocks by considering micro-fractures at the grain scale. Grains generated with the Voronoi tessellation are allowed to fail in tension or in shear using a strain-softening model. Damage is represented by either grain boundary fracture or grain failure, or the combination of the two. As stress increases, the process of damage, fracture initiation and coalescence in rocks can be captured.The grain-based model was calibrated using test data of the Lac du Bonnet granite and a parametric study was conducted. Numerical simulation results showed that the proposed modeling approach is able to capture most of the mechanical properties, fracture pattern, and dilation behavior in both unconfined and confined loading conditions. In an unconfined compression test, interactions of microscopic fractures may lead to macroscopic shear or axial splitting failure depending on the chosen micromechanical parameters. Numerical experimental results show that the dilation behavior of the model is strongly related to the failure mechanism of rocks. Tensile-failure-dominated failure mode generates large dilation due to the formation of new cracks that are sub-parallel to the loading direction. On the other hand, shear-failure-dominated failure mode produces small volume increase. One significant finding from this study is that in order to capture large dilation using grain-based UDEC models, intragranular grain failure should be considered."

Jan 1, 2015