Search Documents

By D. A. Stokes

"In October of 1980, Fording's 15 000-ton capacity clean coal silo was put into operation. The silo was unique in that it was designed to allow the mass flow of material, coupled with a sophisticated computer-controlled dynamic loadout/weighing system.On May 1, 1982, an explosion, attributed to a methane buildup, devastated the top of the silo. .As a contingent plan to minimize the effect of the production loss the conveyance to the silo top was reconstructed and the silo' was back in operation by mid-June 1982, although the silo top was left open to prevent further methane buildup. As dust emissions occurred during loading ofthe silo, an extensive study was undertaken to establish dust control for the silo, while at the same time providing methane detection and control.The study, conducted for Fording by the Cambrian Engineering Group of Calgary, involved an extensive search and investigation of existing coal silos. The study concluded that there IS no universally accepted method of controlling methane emissions in coal silos.The study also produced a unique conceptual design for handling methane, while at the same time, protecting the environment . Fording's Clean Coal SiloThe silo, located at Fording Coal's Fording River metallurgical coal operation, is utilized for the storage and load out of cleaned thermally-dried metallurgical coal.The silo was constructed in 1979 and 1980 to reduce unit train loadout times and to facilitate the handling of “special shipments"" of coal. The silo went into operation in October 1980, under manual control and utilized computerized, automated loading by February 198I.The silo is 21 m in diameter and 76 m high, with a nominal capacity of IS 000 live tonnes. The coal storage portion of the silo is 21 m in diameter and 48 m high, utilizing 2 steep-angled hopper outlets allowing mass flow of the stored coal during train loading. Each hopper has a control gate and a discharge chute, one chute for bulk loading, the other for trim loading of coal into the rail cars."

Jan 1, 1986

By A. J. Williams

"IntroductionAN EXCELLENT paper entitled Potash Discoveries in Western Canada (l) was presented to the 1948 Annual Meeting of the C.l.M. by L. Heber Cole, of the Department of Mines and Resources, Ottawa. In the intervening three and a half years, the search for oil and gas in Saskatchewan has added considerably to the information available on the occurrence of potash. It is the purpose of this paper to summarize the additional data. For greater clarity, it may be useful, first, to recapitulate some of the highlights of Mr. Cole's paper.Underlying the western plains of Canada there is a large deposit of sodium chloride, believed to be of early Devonian age. Associated with the sodium chloride are certain potash salts, primarily 'sylvinite,' a mechanical mixture of sodium chloride (halite) and potassium chloride (sylvite) crystals. The potash salts, when present, are usually near the top of the salt formation, though in at least one well they were found near the central part of the deposit. Cole reported on some seven wells in Saskatchewan which had encountered appreciable amounts of potash; these were the Ogema, Radville, Davidson Nos. 1 and 2, Prairie Salt Nos. 1 and 2, and Verbata wells. Depth of potash from surface ranged from 7,653 feet in the Radville well to a minimum of 3,466 feet in the Verbata well. Such depths do not compare favourably with those at which the potash is found in mines in the United States, France, and Germany, where about 1,000 feet is the average. The greatest concentration of sylvite encountered was in the Verbata well, where a bed 11 feet thick carried the equivalent of 21.64 per cent K20."

Jan 1, 1952

By Daniel D. M. Adams

Over the last 100 years industry in general has been trying to advance the ability to maintain systems through management processes. Mining has looked to utilize onboard data systems in our mobile mining fleets to compliment these processes. Combining the two concepts build the concept that Rio Tinto refers to as asset health. These programs can generate a cost shift between $20,000 and $100,000 per piece of equipment annually. Even with the documented savings many operations struggle to justify the systems, why?

May 1, 2011

By Himmelman. Nicholas P.

In this paper, the hardware foundations and data collection methods of a real time collision avoidance system for electric surface mining rope shovels are described. The primary goal of the system is to help a shovel operator avoid accidentally colliding the shovel?s dipper with either a nearby haul truck or the shovel?s tracks. To achieve this goal, the system requires complete and precise knowledge of the shovel?s geometry and movement, as well as the location of any nearby haul trucks. This paper describes the subsystems created to acquire this necessary information. This system is unique in that all of its components are mounted solely on the shovel and that it is designed to be easily retrofitted to a shovel without significant modifications.

Oct 1, 2009

By Michael K. O’Leary, William D. Coplin

"Risks from political instability and government policies restricting equity ownership, local operations and transfers of payments affect the profitability of foreign mining ventures. More than seat-of-the-pants judgments and old-boy networks are required to anticipate these risks and to take actions appropriate to offsetting them. A system for making political forecasts, called the Prince System, and a series of charts relaying risk s to a production of key minerals will be presented.IntroductionFirm s with extractive operations outside their home country do not have to be told that political stability and government decisions play a big role in the success o f their operations. The takeover of copper firm s in Chile during the Allende administration in 1971 and the recent decision by Venezuela to reduce Reynolds Metals equity share in a smelting operation from 50% to 28% are two examples of hundreds of events that have determined the profitability of extractive operations over the past decade. Both risks and opportunities for international firms seeking to produce and market raw materials are heavily affected by political conditions. While news of political events travel much faster than in the past and host governments are more clever in shaping the risks as well as the opportunities, politics has always been part of the mining business.What has changed is the need to be more systematic in approaching the assessment of political conditions and how it affects business. The increasing costs of extractive operations, the need for long-range planning, the importance of financial arrangements and the world-wide scope of man y firm s' activities require that the assessment be updated continuously and be comparable across different countries and different types of investments. Political risk analysis, the assessment o f macro-political changes and specific governmental decision s on the operations of extractive industries needs to become as systematic and integrated into corporate decision -making as economic analysis has become over the past two decade s."

Jan 1, 1983

By J. Olsson

The paper describes and discusses the use of stainless steels for leaching plants emphasising the duplex family, i.e., austenitic-ferritic stainless steels. This group has generally twice the proof strength of the more common 300-series austenitic grades, which implies possibilities to reduce the gauge at construction of pressure vessels and atmospheric tanks and vessels and thereby possibilities to reduce the weight. The duplex grades have also higher surface hardness resulting in better resistance to mechanical wear, i.e., abrasion and erosion corrosion. The lower contents of nickel and molybdenum imply lower cost and a more stable price considering the present market situation for these alloying elements. Corrosion data from laboratory and pilot plant tests, as well as examples of applications of duplex and highly alloyed austenitic grades, are presented. Cu2007 - Volume IV (Book 1) The John E. Dutrizac International Symposium on Copper Hydrometallurgy Edited by P.A. Riveros, D.G. Dixon, D.B. Dreisinger, M.J. Collins Toronto, Canada,

Jan 1, 2007

By Xiao Huang, Dongmei Wang, Prakash Patnaik

Further increase in gas turbine engine temperature necessitates continuous development and advancement to thermal barrier coatings. While tremendous effort has been devoted to developing new thermal barrier coating materials and processing methods in order to decrease the thermal conductivity, limited attention has been paid to radiative thermal transport through coatings. It is the purpose of this study to develop a new layered coating structure that can be used to effectively reduce the both radiative thermal transport as well as thermal conductivity, and to demonstrate the mechanism and effectiveness of the proposed multilayered structure. Mathematical modeling based on the multilayer quarterwave stack and simulation results are presented.

Jan 1, 2004

By Chia-Chi Chiu, Meng-Chia Weng, Tsan-Hwei Huang

"This paper proposes a biconcave shape bond model for the distinct element method (DEM) to simulate cementation between two circular particles in geomaterials. Rather than an original parallel bond model between particles, the proposed model adopts the more realistic shape of cementation and considers the elastic response of cementation under external loading. The stress field and force-displacement relationship of the biconcave shape bond is based on Dvorkin’s theory, and three modifications are adopted: (1) A superposition method is applied to improve the correctness and symmetry of the stress field, and it also provides a method of addressing the status when both connected particles rotate; (2) To simplify the input parameters, the tangential movement is replaced by the normal deformation and rotation between particles; (3) To accelerate the calculations, variables are extracted in analytical procedures, which provide an efficient method for applying the bond model with only one matrix inversion. With these three modifications, the new biconcave shape bond model is created.To assess the validity of the proposed model, this study compared the elastic deformation in a single bond with an elastic analysis performed using the finite element method (FEM). After verification of the proposed model, a series of sensitivity analyses was performed to explore the effect of bond shape and the differences from the parallel bond model. For a single bond, the results showed that a biconcave model can represent the mechanical behavior of a biconcave shape bond and is effective with different bond shapes. The stress fields calculated by the biconcave model were more similar to the FEM results than those obtained using Dvorkin’s theory. The width and thickness of a bond have a considerable effect on its stiffness, and the variation of thickness decreases with the width of the bond. In addition, the required parameters can be acquired directly from real bond material rather than using the back analysis procedure for parameters.The biconcave model was further implemented in DEM software Particle Flow Code 2 Dimension to certify its applicability in geotechnical engineering. Using this model, a series of uniaxial compression test simulations was performed to analyze the macroelastic responses of specimens. The results showed that the macrotangential elastic modulus and Poisson’s ratio had a regular tendency, and they agreed with the stiffness variation in a microbond. This finding can assist in determining correlations between microand macroproperties and provides an innovative method for simulating the behavior of cemented granular material."

Jan 1, 2015

By I. Paredes, R. Díaz, H. Henao

Smelting of copper concentrate generates a significant amount of dusts which are collected in electrostatic precipitators. This material, which is a complex oxide of Cu, Fe, S, As, Sb, Bi and others, is difficult to recirculate into the smelting process due to the reported high concentration of arsenic. However, the dust also has concentration of copper above 10wt %, aside from reported contents of silver corresponding as much as 25wt% of the total inventories of this element in the smelters. Thus, it is of economic and environmental interest the development of a process able to reduce the concentration of arsenic in the dust and produce a material suitable to be recirculated into the smelting process. The present experimental work shows the results of a process of dust sulfidization-oxidition able to remove more than 65wt% of the arsenic present. INTRODUCTION Copper sulfide deposits worldwide exhibit increasing concentrations of arsenic. One case of interest would be the copper ores from the northern zone of Chile, which report high concentrations of enargite (Cu3AsS4) (Revista química, 2015) (Latinominería, 2014). The obtained concentrate from this ore is treated in a Fluidized Bed Roaster, producing calcines with low concentration of arsenic (<0.5 wt% As). This material is suitable to be treated in a Flash Furnace. At the roasting process, the arsenic is volatilized and then precipitated as fine particles of complex oxides. Most of this particulate material is removed from the gas stream through a device called Electrostatic Precipitator (Minería chilena, 2014). The experimental results reported in the literature indicate that arsenic present in these particulate materials (or dusts) cannot be eliminated in oxidizing atmospheres (air) or with inert gases (N2) in a Fluidized Bed Roaster even at temperatures as high as 700°C. There is also information that even the recovery of valuable metals from the dust is difficult through hydrometallurgical processes (private communication). This is how in some foundries these dusts are considered environmental liabilities. Regarding the decomposition of enargite (Cu3AsS4) in neutral atmosphere, it is reported in the literature (Padilla, 2001) that the main chemical reactions are:

Jan 1, 2019

By Joseph J. Mgumbwa

Pillars are any structures left between two or more underground openings. The stability of pillars is normally considered to depend on shape (defined by width to height ratio), rock mass strength, extraction ratio, in situ stresses and the gross structural features (i.e. joints, contacts, faults etc). Recent experience has shown that pillar stability is also controlled by the relative orientation of the orebody with respect to the in situ principal stress. In inclined orebodies, pillars are loaded in compression and shear, thus creating unsymmetrical stress distribution. Failure mechanisms of these pillars are little known. This paper investigates the failure mechanisms of pillars under shear loading. Two dimensional elastic numerical modeling was used to examine the behavior of pillars in different orebody inclinations relative to the major farfield stress orientation. First, the paper reviews pillar design approaches including the empirical pillar design chart and uses numerical modeling to investigate the effect of the major farfield stress orientation on pillar stability. It is concluded that the empirical pillar design chart be used with caution, and that for orebodies under shear loading mine planning and design should take this into consideration since such geometrical orebody/stress relations put mine structures at higher risk of instability.

Oct 1, 2010

By Z. D. Hora

Several deposits of crystalline magnesite are known in southeast British Columbia. Deposits at Cross River and Marysville have been thoroughly explored, but as yet there has been no commercial production.

Jan 1, 1984

By A. I. A. Salama

The CANMET Western Research Centre (CWRC) has developed a hydrocyclone model simulation of dewatering and fine particle separation circuits. The simulation is based on an existing empirical model. Utilizing a cyclone manufacturer’s published data, some modifications have been developed and integrated into the model. Feed stream characteristics, cyclone mechanical dimensions, and operating conditions are used in the CWRC modelling simulation. The computer results are presented in 3D graphs and corresponding 2D maps showing the cyclone mass recovery, percent solids by mass in underflow and overflow, and cut size as functions of the cyclone apex diameter and cyclone throughput (i.e., inlet pressure or pressure drop). Results of the computer simulation have been used in the economic feasibility and design of several dewatering circuits in oil sand plants.

Jan 1, 2003

By Elma van der Lingen

Gold is considered the most inert of all metallic elements, but the metal can show catalytic activity when prepared by specific techniques. Preparation techniques being used to prepare gold catalysts systems mainly involve precipitation methods incorporating gold compounds or complexes. This paper introduces a totally different method for the preparation of gold-based heterogeneous catalysts that can be used for oxidation and reduction reactions, as well as electrocatalysts. The method involves alloying of gold with a less noble metal, such as aluminium, to form a gold-containing intermetallic precursor. AuAl2 was produced by melting gold and aluminium together in a vacuum arc furnace under a protective atmosphere. The aluminium is then dissolved from the AuAl2 precursor by means of NaOH to produce a highly porous gold structure. The paper also reports on a method of incorporating transition metal oxide(s) with the porous gold to form an active heterogeneous catalyst. Promoter elements can also be melted with AuAl2 to improve catalytic activity. Alloying has the advantage that the promoter element can be in contact on atomic level with the gold. In-situ xray photoelectron spectroscopy (XPS) studies have also been done on the porous gold catalysts to further clarify the CO oxidation mechanism on gold-based catalysts.

Oct 1, 2003

By R. Stauber, B. Friedrich, S. Hilgendorf, G. Homm, C. Gellermann

Due to recent regulations limiting tolerated lead concentrations in copper alloys, new recycling strategies have to be considered. This study investigates the suitability of technical approaches in order to recycle leaded copper alloys exemplified by CuZn39Pb2 and produce an alloy in compliance with future lead regulations in the European Union. Three pyrometallurgical methods are considered to achieve this goal, namely vacuum distillation, intermetallic precipitation and fractional crystallisation. The impact of essential process parameters i.e. pressure, temperature, time, atmosphere and quantity of additives are identified using thermochemical and kinetic modelling. An experimental implementation reveals a general suitability of all three refining processes. However, the individual efficiency of the different methods strongly differs. Thus, a detailed assessment is carried out in order to provide an evaluation on the efficiencies of these methods from a technological, economical and environmental point of view. Taking a possible industrial realisation into account, the authors recommend the approach of vacuum distillation, although the energy demanded is comparatively high due to the enthalpy of evaporation for zinc, or rather, lead. However, required lead concentrations can be reached quickly without introducing an external element to the material. The prediction of selectivity and evaporation speed, which are immanent variables for a successful implementation, can be validated experimentally. INTRODUCTION In 2016 approximately 1 million tonnes of leaded copper alloy semi-finished goods with an average lead content of 2.1 Ma% have been produced in the European Union (EU). The global production in the same period exceeded 5.5 million tonnes, while the lead concentration has stayed constant at around 2.4 Ma% for the last 50 years. Up to 80 % of the current production volume is covered with end-of-life scraps, which are used for direct re-melting, depending on the alloy composition. Lead has been a popular alloying element in copper alloys in general, and in particular in brass due to its positive impact on various mechanical, physical and chemical properties, especially machinability. Health and environmental concerns were drivers for many governments to implement limitations on lead. In order to further utilise the resource potential of leaded copper scrap, it is inevitable to develop methods to efficiently eliminate lead from circulation as far as possible. (Glöser, Soulier, & Tercero Espinoza, 2013; Soulier, Glöser-Chahoud, Goldmann & Tercero Espinoza, 2018)

Jan 1, 2019

By A. C. Wilson

"In 1991, local prospector C. “Mickey” Clement recovered at least three alluvial diamonds from the Michipicoten River. Two of these stones were sent to the Department of Mineralogy, Royal Ontario Museum, where they were identified as industrial-grade diamonds with weights of 1.05 and 1.13 carats. Both stones were described as frosted and graphiteinclusion riddled.In 1995, prospector Sandor Surmacz and geologist Marcelle Hauseux discovered diamonds in bedrock approximately 20 km north of the Michipicoten River. An 18.1 kg bulk sample of a xenolith-rich lamprophyre, taken from an outcrop at the side of the Trans Canada Highway north of Wawa, yielded 1 macro diamond and 5 micro diamonds. All but one was gem quality (Sage, 2000).Since then, more than 36 occurrences of diamonds in bedrock have been reported in an area approximately 30 km2 in size, centred 20 km north of the town of Wawa. The occurrences are hosted within a sequence of unusual, Archean-aged, heterolithic breccias previously considered to have no economic significance. Ten kimberlite occurrences also have been confirmed in the Michipicoten greenstone belt in the last five years. Two of these kimberlites are diamondiferous.To date, expenditures on property acquisition and diamond exploration in the Wawa are estimated at CDN$120 M.This paper summarizes the geological observations made on these occurrences and describes the relationship between the occurrences and the regional geology."

Jan 1, 2004

By Brian Hart, Stamen Dimov, Aparup Chattopadhyay, Barun K. Gorain

"A novel gold deportment technique has been developed for complex copper-gold and double refractory gold ores using state-of-the-art technology. Characterization of these ores is a challenging task due to low copper and gold grades in ores, presence of both primary and secondary copper sulfide phases and variable proportion of visible and invisible gold in different sulfides and iron oxide phases.Double refractory ores are mainly composed of silicates and carbonates with moderate clay and mica, and minor amounts of sulfides and organic carbonaceous matter. Gold mostly occurs as ""invisible gold"" (sub-microscopic gold) as solid solution or as colloidal-sized particles in different sulfides and other phases. The dominance of invisible gold and presence of highly preg-robbing and finely disseminated carbonaceous matter adversely affects gold recovery in flotation and leach circuits. Characterization of this carbonaceous matter, commonly known as TCM and quantification of gold associated within TCM, along with different sulfide and oxide phases is highly complex and challenging.Studies were initiated on various complex ore deposits and also on samples representing various process streams. This paper presents the development of a systematic approach to diagnostic metallurgy using state-of-the-art optical and automated mineralogy techniques, namely, micro-probe, dynamic SIMS and TOF-SIMS analysis for quantification of invisible and visible precious metal content in various species. The relevance of the mineralogy characterization to metallurgy will also be discussed in this paper."

Jan 1, 2016

By Z. -E. Nakagawa, O. Yamamoto

After the formation of a concentration gradient of SiC within C-C composite, either zircon or mullite thin films were coated on the surface by sol-gel process. Oxidation resistance tests of as-prepared composites with a couple consisting of a ceramic thin film and a SiC-gradient were then carried out in air at the temperature range from 600 to 1600°C. By the coating of zircon with a thickness of 1.5 µm, a pronounced oxidation resistance was observed; the mass loss by oxidation was almost negligible at 1000°C and one hundredth of original composite at 1400°C. In the case of the coating of mullite with a thickness of 1.0 pm, the marked improvement in oxidation resistance over the whole temperature range examined, from 600 to 1600°C, was found with the combination of a SiC-gradient and a mullite thin film

Jan 1, 2004

By C. Ketata, M. C. Rockwell

During the operation of a mineral processing plant, the unit processes are investigated by analyzing the data extracted by means of stream sampling. The data structure is identical to the time series form. Data analysis is a crucial step in understanding the plant performance. To control the plant performance efficiently, it is very important to avoid sampling errors, which is impossible. However, it is possible to minimize these errors. The factors influencing these errors are divided into two categories: material properties illustrating its heterogeneity, and sampler features. The purpose of this paper is to study the influence of the material composition variation on sampling errors, and to compare our evaluation method with that of Gy. Note that the stream mass flowrate is assumed to be constant during the sampling process.

Jan 1, 2001

DynoMiner APS Delivery Systems Overview ? New Design of DynoMiner APS-M2 ? Stand alone or attach to Cargo type 10,000 lb (4536 kg) emulsion bins. ? Hose reel w/200-ft (61-m) by 1-inch I.D (25-mm) hose capacity, power rewind. ? Increased water and trace capacity. ? Hose reel and gassing offered as options. ? New Flow Meter ? DN-100: aluminum body, UHMWPE rotors. ? Will be offered as an option. ? APS Nomenclature ? Proposed changes ? DynoMiner APS and APS-M1 to become DynoMiner APS Drifter ? DynoMiner APS-M2 to become DynoMiner APS Stoper. ? Both to have optional gassing / flow metering.

May 1, 2004

By Laxman (Lucky) Amaratunga, Hisham Madi

Final disposal of mine wastewater neutralization sludge continues to be one of more pressing problems in the mining industry. The disposal of mining and metallurgical waste products into underground reduces the environment impact and improves the safety of the mining operation and the economics of the enterprise. This current research focuses on an investigation of utilization of mine wastewater neutralization sludge obtained from Kidd Creek Mine site, as a supplementary material for their proposed deep mine pastefill system. Their proposed pastefill consist of combination of rock aggregate in a matrix of imported sand and tailings with binder (Portland cement + Slag cement). Pastefill mixes containing various percentages of the waste sludge 0 (control mix), 1, 2, 3, and 5% by weight as replacement to the fine sand were prepared and tested with different percentages of binder. Hypothesis behind this approach is to study the behavior of sludge as replacement of sand in matrix as well as its ability to act as a binder. Compressive strength, percentage of sludge, binder dosage, slump, water to cement ratio, percentage of solid, and curing time are being observed. The results indicated that sludge can be incorporated into the pastefill and enhance its strength without compromising the pastefill quality and integrity.

Jan 1, 2004