Search Documents

By W. R. Hargrave

"Mining OperationsOre will be mined by open pit techniques. Because of the high grade of the deposit and the low strip ratio, mining rates are small relative to most other open pit operations.The ore deposit is located in the valley of the main fork of Red Dog Creek. The bulk of the deposit is located on the southwestern flank of the creek, but mineralization does traverse the creek in both the north and east directions.Erosion has exposed the orebody in a number of locations, and has resulted in oxidation of the mineralization closer to the surface. Although much of this oxide material is very high grade, it leaches readily and, at least in the initial phases of the operation, will be stockpiled and not treated in the concentrator.During construction, 2.3 million mt. (2.5 million st.) of overburden and waste will be stripped from the orebody to expose ore for initial operations. Competent non-mineralized waste will be used to build roads and waste dumps, but the bulk of material removed consists of oxide or ice-rich soils and weathered rock which is not suitable for construction.The annual ore mining rate will be 1.9 million mt. (21. million st.). The strip ratio will start off at 1.2 to 1, falling to 1.0 to 1 by year 5 and ultimately to 0.8 to 1.Bench heights are set at 7.6 m (25 ft). Pit slopes will vary depending on the material present in the wall. The slope, through competent waste and the sulphide package, was set at 45 degrees. This is flattened to 26 degrees (i.e. 2: 1) through overburden and Upper Kivalina shales. The Kivalina Shales are an ice-rich shale whose carbonate matrix has been leached out and which exhibits little or no strength as it thaws. In addition, a 100 ft containment berm will be left in the wall below overburden and Kivalina."

Jan 1, 1989

By Akira Fujisaki

"The oil crisis accelerated the change of non-ferrous metals' demand structure. Maturing societies in developed countries and preference for lighter, thinner and smaller products are eroding the non-ferrous metal industries' growth potential. Inventory-control, stockpiling and developing new demand are measures Japanese smelters have taken to cope with the changing demand.The most effective means for risk management of product demand lies in the cooperation between ore producing countries and metal consuming developed countries to assist developing countries in their efforts to ""take-off"", which in turn will bring about a surge of demand for metals.SummaryThe non-ferrous metal industry in the world is suffering its most serious slump since the war. With some of the markets of the advanced industrialized countries approaching saturation point and economized usage of natural resources and substitution growing, the possibility of a quick recovery of the demand for base metals is dim.To cope with the changing product demand Japanese producers have had recourse to such measures as strict inventory control and stockpiling for the purpose of stabilized imports. They have also tried hard for securing raw materials and promoting new field s of demand but the very core of ""risk management"" has been the diversification of line s of business to bolster and stabilize the foundation of management of the non-ferrous metal industry in Japan.To see the demand for nori-ferrous metals recover from the slump and be put on a path of solid development, we have to wait for the economies of the developing countries to ""take off"" and for its realization the economies of the developed countries must be reactivated with new growth industries playing a leading role, and the transfer of technology and money recycling must be carried out smoothly under an orderly international trade system."

Jan 1, 1983

By A. J. Oliver, C. E. O’Neil, I. J. Itzkovitch, V. A. Ettel

A new solvent extraction process for the separation of cobalt, copper and zinc from nickel sulphate process streams has been developed. It involves selective extraction of these elements with a quaternary ammonium thiocyanate dissolved in an aromatic diluent. The chemical principles of this process have been investigated and are described, together with background physico-chemical data relating to the use of this solvent. Long-term testing in a continuous "mini-plant" circuit gave high-purity nickel and cobalt products (Ni/Co —200011 and Co/Ni ~1000/1 respectively).

Jan 1, 1976

By R. W. Guill

"The Apex Mine is currently scheduled to be brought back into production by Hecla in the first quarter of1990. Its projected productivity rate will be exceptionally high for a small underhand cut and fill mine.The ore mined at the Apex Mine occurs within a pipe-like structure as a series of iron oxides containing both gallium and germanium, plus significant amounts of silver, zinc, lead, and copper.Ground conditions in and around the ore zone have dictated that unique approaches be utilized. To date, these have included a prototype 0.5 cu. yd diesel LHD, and the use of fibrous shotcrete in 4ft by 7ft headings, and the first pneumatically-placed cemented backfill in North America. Above all else, it is the combination of new technologies with a small and dedicated workforce which has allowed for the successful development of this ore body.IntroductionThe Apex Mine is an example of the typical small underground project. It has high grade, but low tonnage and is deposited in poor ground. In such cases, conventional planning and thinking generally results in an uneconomical evaluation and negative production decision. Fortunately, some unconventional thinking was allowed to take place during the planning and evolution of the Apex Mine development. The result now serves as an example of how such unconventional thinking can lead to the type of innovations described below.The job necessitated the development and use of new equipment and materials to execute a highly flexible underhand cut and fill mine design/pneumatic backfill concept, that must be constantly modified as different than assumed conditions become evident in and around the ore zone."

Jan 1, 1990

By Donald Lindell

Safety Share ?Dad receives fryer for Christmas 2009 and makes delicious sweet potato fries ?When the oil fryer was pushed back on the stove for cooling, the back edge comes into contact with the stove top controls, unknowingly activating the cooking element, family leaves kitchen. ?Faint smell of smoke from the melting plastic alerted the family; teenager arrives first and pulls the fryer forward causing oil to spill onto hot stove and burst into flames that reach the microwave ?Teen runs for sink to grab pan of water but is stopped by Dad ?Dad opens refrigerator, grabs baking soda and pours it on fire, extinguishing flames Lessons 1.DO NOT USE WATER ON GREASE FIRE 2.Where is the baking soda in your kitchen?

May 1, 2010

By A. E. M. Warner, P. J. Mackey

Copper metal is produced in large or small tonnages in almost all countries of the world—handling raw materials in the form of either as-mined or milled ores, custom concentrates, or other custom materials including scrap and recycled copper. The scale of operations and type of technologies used around the world varies widely. There is a certain concentration of both mining and smelter-refinery production as a total of ten countries produce some 80% of world mined copper, while ten countries—mostly different ones— produce about 80% of smelted and refined copper. As a result, international copper trade is significant. The present paper takes the reader on a virtual tour of the copper plants throughout the world with a focus on smelter facilities. Operations and technology employed at each plant visited are discussed including a brief historical sketch. Future trends identified during the world tour are also discussed. The present authors considered sufficient time was required for a thorough study tour and settled on eighty days—the same as that for the celebrated fictional story of world circumnavigation in the 1870s. INTRODUCTION The celebrated French writer Jules Verne published his book “Around the world in 80 days” in English in1873 and it is the story of Phileas Fogg and his French valet Passepartout circumnavigating the world in 80 days in the fall of 1872 on a £20,000 wager (equivalent to over 2 million pounds today) from the exclusive Reform club in London. This is an interesting period for copper as it started trading on the London metals Exchange in 1876 and the start of global copper production chains started to take off at this time with the rapidly increasing electrification of the world. The production chain includes mining, mineral processing, smelting, refining and fabrication. Since 1880 annual world copper production has increased by over 150 times from 154,000 tonnes in 1880 (nominally considered as smelted copper—essentially the only route at the time to marketable copper) to over 23 million tonnes today (including total refined copper of 19 million tonnes of smelted copper including scrap and 4 million tonnes by solvent extraction-electrowinning), in tandem with increased electricity usage, along with significant transportation usage and for manufactured products (Figure 1).

Jan 1, 2019

By F. T. Manns, G. Harper

"The Swayze gold mine is an Archean vein deposit in northern Ontario. The veins are superimposed on a conjugate joint system and are contained within an anastomosing alteration envelope in a metadiorite body. Reserves were estimated on the basis of fire assays of channel samples and car load samples from underground mine openings, surface and underground diamond drilling and surface trenching. A semi-variogram constructed from channel samples along one of the drifts yielded a horizontal, regionalized influence of approximately 9.0 m. Common industry practice has been to use 6.1 m for similar deposits in Ontario. Proven ore was defined from underground openings. The maximum extrapolation distance for proven ore along strike and dip from a data point is taken to be 6.1 m. Probable ore is extrapolated 7.6 m from a data point in a mine opening or from a drill intersection. Possible mineralization is based on geological continuity one-half the distance to a neighbouring data point.The mineral inventory estimate of 1.45 million tonnes at a grade of4.8 g Au/tonne gives an excellent outline of the geology of the deposit. The deposit contains 313 000 tonnes of ore reservesat a fully diluted grade of6.9 g Au/tonne. These figures include dilution for several reasons: (I) a 2.1 m mining width is used rather than the more typical 1.5 m width to allow for over break because of the shallow dip of some vein zones; (2) over break is allowed for adjacent to major unmineralized dykes; and (3) grams of gold are deleted from estimates to allow for the mining of unavoidable minor dykes.A personal computer with off-the-shelf software was used to compile 712 geologically defined ore blocks and sort them into a number of revealing categories. The computer was used to perform grade sensitivity tests, as well as to evaluate depth potential. Hopefully, the reiterative aspect of the method has randomized the errors and helped to cancel their effects."

Jan 1, 1987

By Réal Marcotte

L'industrie minière représente un apport économique important pour le Québec ; cette production est très diversifiée et répartie dans plusieurs régions. Hormis les forges du St- Maurice au XVIIe siècle, l'industrie minière québécoise commence en 1862 dans la Beauce avec l'exploitation de placers aurifères dans les affluents de la rivière Chaudière; à la même époque, on met en production les mines de cuivre Eustis, Albert et Capelton, près de Sherbrooke1; à partir de 1881, les mines d'amiante et de chromite au voisinage d'Asbestos et de Thetford commencent à voir le jour. Dans les années ?20, l'extraction de métaux précieux et usuels débute en Abitibi- Témiscamingue; durant les années '50, le fer et l'ilménite de la Côte Nord, ainsi que le cuivre de Murdochville et Chibougamau, commencèrent à être mis en valeur. Plus récemment, soit durant les années '80, le sel des Iles-de-la-Madeleine et le graphite des Hautes Laurentides s'ajoutèrent aux produits que nous commercialisons. Finalement, soit en 1998, le Québec devenait un important producteur de nickel avec le démarrage de la mine Raglan, au Nunavik. L'exploitation d'une mine peut nécessiter l'extraction de grandes quantités de roches stériles, particulièrement lorsque la production se fait à partir d'une fosse à ciel ouvert. De plus, étant donné que les minéraux et les métaux mis en marché ne constituent qu'une fraction du minerai extrait, il faut le concentrer : on se retrouve alors avec des proportions plus ou moins importantes de résidus finement broyés. Ces deux types de rejets totalisent bon an mal an environ 100 millions de tonnes. Lorsque cela est possible, ceux-ci sont, soit valorisés comme matériaux de construction ou retournés dans leur lieu d'origine afin de soutenir les murs des excavations. Toutefois, une bonne partie est accumulée en surface dans des aires aménagées spécifiquement à cette fin ; comme le montre la figure 1, la superficie utilisée à cette fin a progressé parallèlement aux booms miniers que nous venons de mentionner pour atteindre actuellement environ 15,600 hectares, dont environ la moitié sont situés sur des aires encore en activité.

Nov 1, 2002

By D. W. I. Griffiths, J. C. Bélanger

"La Division Matagami de Minéraux Noranda inc. a profité de la construction de sa nouvelle mine (Isle-Dieu) pour continuer sa modernisation.L'utilisation d'automates programmables (PLC) s'est intensifiée pour contrôler et automatiser de plus en plus d'équipement dans ses minessouterraines, au concentrateur, dans les atelierset bureaux.Tous les PLC comrnuniquent entre eux et les IBM PC sont utilisespour exterioriser l'information et faire Ie lien entre Ie personnel et les automates. Le système Central IBM 36 emmagasine les donnees traitees par lesPLC (a travers les PC). Ces donnees sont transmisesau programme d'entretien de chaque equipement et compile les heures, cycles, tonnes, etc., fait imprimer automatiquement les feuilles d'entretien préventif ', etc.Les principales realisations adate et en progrès pour la mine Isle-Dieu sont:• automation complète du système de remblayage du concentrateur ala mine Isle-Dieu situee a2 km de la mine principale;• automation du fonctionnnement des ventilateurs qui comprendra la position des portes de ventilation, Ie chauffage, Ie débit, etc.;• automation des pompes, surveillance des sous stat ions électriques, concentration des gas (CO, SO2) à chaque niveau en tout temps et du propane à l'entree d'air frais;• tonnage et cycles par Ie treuil; et• contrôle d'autres équipernents à differénts niveaux. D'autres travaux furent egalement effectues par les employes, tels que:• la conversion d'un Scooptram ST5A de diesel à électrique;• I'installation complete de systèmes de depoussierage a I'eau (scrubber) pour le concassage secondaire;• I'installation d'un marteau hydraulique avant les concasseurs coniques;• la rénovation des cellules de flottation ; et• l'installation d'un système de gardiennage par caméra. D'autres projets seront effectués ou étudiés:• automation d'un Scooptram"";• automation d'un marteau hydraulique;• récupération de Scooptrarn; téléguidé:• gestion de l'énergie, contrôle de la demande, surveillance et contrôle de l'équipernent de machines fixes(compresseurs, boulloires, pompes à vide, génératrices, débits et pression d'air, eau pour diagnostiquer les problémes, analyser les coûts;• concasseur portatif pour fabriquer de la pierre concassée pour utiliser dans les chemins sous-terre, et• utilisation de micro-ondes pour transmettre les images captées par camera."

Jan 1, 1990

By I. S. Laitinen

Outokumpu Technology has recently introduced new technology in both copper electrorefining and electrowinning. This technology includes, among other things, a new permanent cathode (Outokumpu Permanent Cathode) and new busbar technology (Outokumpu Double Contact System). The new technology has already been tested in commercial scale cells. To get a better understanding of the busbar system a multiphysical simulation model of the electrowinning and electrorefining cells was developed. A mathematical model of electrical conduction and heat transfer in a copper electrolysis cell was developed from partial differential equations. The model was expanded to a cell group including seven electrolysis cells connected electrically in series. The model was solved numerically using the finite element method (FEM). Using the model, different intercell busbar systems were simulated. Typical electrical disturbances, like loose contacts between cathodes and the main busbar and short circuits between electrodes, were included in the simulation. The results of the simulation runs with conclusions are presented in this paper.

Jan 1, 2007

By Rob Kelso

The PISCES Goals ? To conduct research and develop programs to enable and promote planetary surface exploration ? To host international tests and technology demonstrations at the PISCES Test Site. ? To promote STEM education, inspiring students by connecting Hawaiian culture to space exploration and settlement. - economic and workforce development ? To involve the commercial sector, spinning off technologies to help the local Hawaiian economy. ? To develop a full-scale, technically valid, analog lunar/Martian outpost on Hawai`i Island.

May 1, 2013

By Dave Shook

A Mineral Processing facility in Montreal has recently implemented a leading-edge intranet solution for monitoring the performance of plant operations, and providing condition-based maintenance. This innovative multi-faceted software implementation incorporates: web-delivered plant information systems; area-wide control loop performance assessment (using sophisticated algorithms to evaluate poorly performing controllers); and integrated alarm management functions. The system has enabled a project to improve plant operations through better process control. Maintenance technicians, engineers, supervisors and managers all can see the performance of the controllers, and the performance of the plant itself, through webdelivered graphics and reports. Information is combined from many sources, real-time, historical, relational and analytical, to provide a complete picture of plant operation. The web-based solution centralizes the administration of user access, and simplifies the deployment of several different kinds of information to many desktops. It is an extensible system that allows users to create and share their own web pages and data views. The paper will discuss the solution architecture and the improvements the I.T., operations, maintenance, and engineering groups have experienced, and overall benefits to the facility.

May 1, 2002

By S. Sagar

In September 1996, Dofasco commissioned a 165 Mt twin shell EAF furnace and an associated ladle fleet. During and after this startup, refractory performance in the ladles was optimized on a holistic approach through several initiatives that increased ladle refractory retention times from 7000 to over 16000 mins (160 heats). This dropped the overall refractory costs by 40% while ensuring a consistent and predictable ladle performance. One initiative that drove enhancements was the proper brick selection for each particular refractory area and it's process conditions. The work concentrated on the selection of a resin bonded alumina magnesia carbon (AMC) brick in the barrel area of the ladle, upgrades to the 2 piece monolithic alumina cast ladle bottom and increasing the slagline refractory brick quality with the appropriate zoning/paneling. The adoption of a magnesia alumina carbon (MAC) brick in the transition area of the barrel/slagline has also improved performance and predictability. The design developments have lowered the overall wear rates and balanced the service life of the entire ladle. Safety was improved and breakout potential reduced by changing the safety lining from a high alumina brick to a state of art technology - monolithic shotcrete lining. This initiative decreased the overall manpower required to brick a ladle and increased shop ladle availability. The ladle bricking area environment was also improved by adopting a post combustion device to burn phenol fumes from ladle preheating practices. This has improved the overall health & safety of the reline teams. The consistent and predictable performance of the ladle on a whole has allowed the shop to decrease the number of working ladles in operation from 5 to 4. This further decreased wear rates from over-oxidation and excessive thermal cycling, saving approximately $500,000 in natural gas from pre-heater operations.

Jan 1, 2004

By G. Mucsi, J. Faitli, K. Bohács

"The authors developed an online tube rheometer to supplement a Netzsch MiniCer (Netzsch GmbH, Germany) stirred media mill in order to monitor online the rheological characteristics of the suspension and therefore the result of grinding during the process. Previously it was demonstrated that the above measuring system was working appropriately based on the preliminary tests. The product related stress model was applied for the evaluation of the grinding results. It was found that the suspension concentration and the change of the material properties during grinding, consequently the rheology strongly affects the grinding result, i.e. specific surface area, median particle size as well as specific grinding energy. The tested model limestone – water suspensions behaved Newtonian initially, then after a given grinding time their properties had changed and they become Bingham plastic. INTRODUCTIONStirred media milling now is a common practice to produce fine and ultrafine granular materials for different purposes. With an increasing demand of ultrafine powders for industries (Kwade, 1999), wet and dry ultrafine grinding has been increasingly used in various fields, such as minerals (Mucsi, Rácz, & Mádai, 2013)(Rácz, 2014), ceramic materials (Becker & Schwedes, 1999), pigments (Ohenoja, Illikainen, & Niinimäki, 2013), chemical products (Baláž et al., 2013), microorganisms (Kwade & Schwedes, 2002) and pharmaceutics (Afolabi, Akinlabi, & Bilgili, 2014). It is well known that suspension rheology affects the wet comminution of materials (He, Wang, & Forssberg, 2006a). The rheological behaviour of the suspension containing the ground particles might indicate the level of interparticle interaction or aggregation and therefore it is an important variable factor of the process control (Muster & Prestidge, 1995). The influence of the rheological behaviour of mineral suspensions on their grindability has attracted more and more interests and attention, especially on ultrafine grinding performance (He, Wang, & Forssberg, 2006b) (Bernhardt et al., 1999). However, there are still many issues concerning the machine and the process for the different applications. When grinding is effective and the particle size range decreases significantly, the circulating suspension is becoming typically non-Newtonian. The changed rheological behaviour and the increasing rheological material parameters can negatively affect the grinding efficiency; therefore it is an important issue. Ultrafine stirred media milling as well as solid-liquid two phase flow have been studied for a long time at the Institute of Raw Materials Preparation and Environmental Processing of the University of Miskolc. Regarding ultrafine grinding the research is focusing on the description of materials’ grindability (energetic aspects) both in wet and dry circumstances (Mucsi et al., 2013; Rácz, 2014). Concerning rheology, the three measuring pipes tube rheometer was developed decades ago (Faitli & Gombköto, 2015). So far many different solid materials from all over the world had been tested in this rheometer (Faitli & Gombköto, 2015). Main aim of these tests was to gain basic data for large scale hydraulic transport applications. Among the many stirred media mills there is a Netzsch MiniCer mill at the Institute. It was reasonable to combine the two fields together, and the goal of the research presented in this paper is to develop an online tube rheometer for the Netzsch mill and to carry out grinding and rheological testing simultaneously."

Jan 1, 2016

By S. Jeon, T. H. Kim

"Understanding the frictional properties of discontinuities is crucial to ensure the stability of underground structures. In particular, the frictional behavior at depth depends on the complex interaction among mechanical, hydrological, thermal and chemical characteristics and their coupled effects. In this study, a series of triaxial compression tests were carried out to investigate the behavior of rough shear surface of synthetic rocks. The frictional behavior showed little variation at different confining and water pressures. The test results were analyzed using Coulomb’s failure criterion. In addition, numerical analysis was carried out using PFC2D to simulate the test.INTRODUCTIONUnderstanding coupled behavior of rock at depth is of great importance in design, construction and operation of underground structures such as a disposal facility of radioactive waste, hot dry rock geothermal system and oil reservoir. In particular, many uncertainties are involved in characterizing deep rock mass deformation in the designing process and interactions among fluid flow of groundwater, high temperature and stress disturbance should be considered. Many independent studies have been carried out to investigate the thermal, hydro, mechanical and chemical coupled effects in numerical and experimental methods. They include the researches by Lockner, Summers, Moore and Byerlee (1982), Jafari, Amini Hosseini, Pellet, Boulon and Buzzi (2003), Tembe, Lockner and Wong (2010), Lee, Lee and Jeon (2012), Indraratna, Premadasa, Brown, Gens and Heitor (2014)."

Jan 1, 2015

By J. M. Shneerson

Gipronickel Institute, Saint-Petersburg will The copper concentrate was extracted from copper and nickel matte after its hydrometallurgical treatment and nickel removal. The concentrate containing 60-74% of copper was represented by two principal copper minerals, digenite and covellite. The oxidising leaching of this kind of concentrate was studied at the Gipronickel Institute. The effect of key parameters, such as temperature, oxygen partial pressure and initial solution compound, on the rate of copper dissolution and transfer of sulphur from sulphide to elemental form was investigated. It was shown that at temperatures about 90DC, the sulphur content of covellite converts to elemental form. Under autoclave conditions at 11ODC, the elemental sulphur dissolves as a sulphate-ion. At the temperature range from 50 to 90DC, the copper dissolution rate is in direct relation with temperature. By increasing the temperature to 130DC, this effect is reversed. Based on the research work, a technological flow sheet for the leaching of the copper concentrate was developed.

Jan 1, 2007

By Erica J. Wanless, Ghislain Bournival, Seher Ata, Jose Hamilton Tavares

In froth flotation valuable particles are captured by bubbles and transferred to a froth layer where bubbles are in close proximity. Bubble coalescence frequently occurs in flotation, especially in the froth layer. The coalescence of two bubbles causes a release of energy, which may expel particles from the bubble surface. A series of experiments were carried out to determine the effect of bubble interfacial properties on the detachment of particles upon the coalescence of capillary-held bubbles of 2 mm in size. The interfacial properties of the bubbles were changed by the addition of low molecular weight alcohols, namely 1-pentanol or methyl isobutyl carbinol (MIBC). Using esterified glass particles (? = 43 °) with a 10 % and 90 % cumulative passing diameter of 47.2 and 92.5 µm, respectively, as model particles, it was found a certain concentration of frother, different for each additive, is needed in order to observe a reduction in the detachment of particles. In the presence of frother, the detachment was evaluated at approximately 65 % which was a considerable reduction in the detachment compared with the value of approximately 85 % found in the absence of frother. Frother molecules changed the properties of the airwater interface. Upon the coalescence of two bubbles, the release of energy caused the merged bubble to oscillate; effectively resulting in the detachment of particles. The addition of frothing agents augmented the elasticity of the bubbles, which appeared to be related to the detachment of particles. Whereas frothing agents are generally used to prevent bubble coalescence and stabilise the froth phase, only transient stability is imparted. The results suggested that an additional role of frothers in flotation is to decrease the detachment of particles from bubble surfaces. The type and concentration of frother can be strategically selected to improve metallurgical recovery as an economic incentive.

Jan 1, 2016

By M. H. Leite, R. Corthésy, D. E. Gill

"La connaissance des contraintes naturelles qui prévalent dans les massifs rocheux est un prérequis indispensable pour la conception sécuritaire et économique des excavations comme on en retrouve dans les exploitations minières souterraines. Certains chercheurs se sont attardés à colliger les résultats de mesures de ces contraintes et les ont utilisés pour produire des modèles de prédiction basés sur leur traitement statistique. Ces modèles de prédiction sont très populaires auprès des exploitants miniers puisqu’ils permettent, du moins dans les étapes préliminaires de design, d’obtenir de façon s’apéconomique mais approximative, une partie des paramètres dont ils ont besoin. Dans le cadre d’un projet initié en 1994 avec la collaboration de l’IRSST, il a été décidé de produire un modèle de prédiction englobant une partie de la zone périphérique de la faille de Cadillac, soit une zone plus restreinte que le Bouclier Canadien utilisé jusqu’ici comme région pour l’élaboration de tels modèles. Pour produire ce modèle de nouvelles données obtenues avec une technique permettant d’exercer un excellent contrôle de qualité ont été ajoutées à celles déjà disponibles. Une telle régionalisation des données de base permet d’obtenir un modèle où les intensités et les orientations des contraintes principales sont beaucoup moins dispersées que ce que rapportent les modèles publiés jusqu’à ce jour. Enfin, il est démontré que le modèle proposé pour la région étudiée est en toute probabilité plus sécuritaire que les modèles plus généraux publiés à ce jour. Knowledge of the in situ state of stress existing in a rock mass is essential to the safe and economical design of underground mining excavations. Prediction models have been published, based on the statistical treatment of stress measurement results. Such prediction models are very popular among mine operators because they allow them, at least at a preliminary design stage, to economically obtain part of the information needed, even if this information is approximative. In 1994, a research project financed by IRSST was initiated aiming to produce a prediction model that would comprise a peripheral zone around the Cadillac fault. This region is more confined than the Canadian Shield on which the existing prediction models have been based up to now. In order to produce such a model, existing stress measurement results have been used in conjunction with new stress measurements that have been performed based on a technique which allows full control of the quality of the measurements. Restricting the data upon which the model is based to a more specific region gives a model in which the intensities and the orientations of principal stresses are far less scattered than the results published to date. Finally, it is shown that the proposed model is probably safer for the studied region than the models previously published."

Jan 1, 1998

By T. Guan, G. Fu, X. Zhou, L. Deng

"One kind of tailings from gravity separation of polymetallic mine contains 0.5–0.8% SnO2. The proportion of –0.037 mm size fraction of the tailings is 37.12%, and the distribution rate of SnO2 is 60.32% in it. For this tailings, two processing technology was carried out. One was felt-shaking table gravity separation in which the concentrate with a grade of 30% SnO2 at a recovery of 10% was obtained. Another was flotation-gravity separation in which the concentrate with a grade of 51.20% SnO2 at a recovery of 51.69% was obtained, but the dosage of collectors was as much as 990g/t. Therefore, the experimental research on the influence of grain size composition on the cassiterite recovery were conducted. The results show that: (1) the flotation recovery of the cassiterite distributed in +0.043 mm size fraction is only 10%, flotation recovery is not suitable for it; (2) a portion of cassiterite distributed in –0.01+0.005 mm size fraction could be recovered by flotation, but the tin flotation performance will be worsened rapidly and the dosage of collectors will be increased due to the increase of the content of –0.010 mm size fraction; (3) flotation processing is not suitable for –0.005 mm size fraction of the tailings. According to the results, a new technology has been carried out, that is discarding tailings by gravity separation-hydrocyclone desliming-flotation-gravity separation processing flow. The processing index is close to that of the flotation-gravity separation processing flow, and the collector dosage is decreased to 360 g/t by this processing technology. And, it has been achieved that the cassiterite slime is recovered economically and reasonably.INTRODUCTIONAs the density of cassiterite is higher than that of gangue, gravity separation is considered to be a low cost, pollution free, and effective process for cassiterite recovery (Wills, 2009). However, cassiterite is a kind of fragile mineral, over crushing is easy to take place and a large amount of slime is inevitably produced in the crushing and grinding of cassiterite. For the cassiterite slime exists in –0.043 mm size fraction, the efficiency of gravity separation decreases sharply. The production practice shows that, for the fine cassiterite, the recovery of tin exists in –0.043 mm +0.010 mm size fraction is about 13% through shaking table gravity separation, and the tin exists in –0.010 mm size fraction is almost impossible to be recovered by gravity separation. If flotation is adopted to recover fine cassiterite, the problems of high reagent dosage, high cost, environmental pollution, and poor economic benefit would take place. Therefore, the recovery of cassiterite slime is a worldwide problem. A key way to increase the utilization of tin resource and increase the economic benefit of tin mines is developing suitable beneficiation process for fine cassiterite."

Jan 1, 2016

By R. Le Houillier, M. Nagamori, A. J. Plumpton

"Asbestos tailings are a typical serpentine, hydrated magnesium silicate, consisting primarily of antigorite and a few per cent of unrecovered fibrous chrysotile. Serpentine has unique thermal properties in that dehydroxylating calcination at 600 to 700°C can yield an amorphous structure in which most of the magnesia is liberated from the original bond with silica and thereby rendered chemically active. The amount of activated magnesia can be quantified by selective leaching with a weak acid such as acetic acid. Many wet processes have been proposed to extract magnesium values from calcined or natural serpentine by means of various acids and their ammonium salts. However, the only commercial utilization of serpentine today is found in dry processes such as the production of fused magnesium phosphate fertilizer .The present paper reviews the physical chemistry of the dehydroxylation of serpentine and also various wet and dry processes in order to provide a general view regarding the chemical transformation of asbestos tailings.IntroductionAsbestos fibers occur as chrysotile, a serpentine polymorph. More than nine tenths of mined asbestos ores consist of massive non-fibrous serpentine, primarily the polymorph antigorite, which is discarded as tailings after fiber extraction. For many decades, Quebec has been a world leader in the production of asbestos fibers. As a result, colossal tonnages of serpentine have accumulated in the Eastern Townships'!'. Serpentine minerals are found in large deposit s throughout the world, and significant research efforts have been made, particularly in Japan and the USSR, mostly in attempts to extract magnesia or silica values therefrom.The chemical composition of serpentine (chrysotile and antigorite) may be ideally expressed as Mg3Si2Os(OH). which corresponds to 43.7% MgO and 43.3% SiO2. Natural serpentines often contain a few per cent of Ni-bearing magnetite and other impurities, and therefore the contents of MgO and Si02are both about 40% or lower.Serpentine (hydrated magnesium silicate) is virtually insoluble in weak acids. However, when dehydroxylated under controlled conditions, ' it decomposes to an amorphous state in which magnesia and silica are isolated and chemically active. The magnesia so activated is readily soluble in weak acids. This unique characteristic of calcined serpentine, first discovered in 1942,, has since attracted the attention of innumerable researchers, whence many processes have been proposed."

Jan 1, 1980