Search Documents

By T. S. Li, D. Ilievski, I. Livk

Micromixing of the fluid and the particulate phases in a continuous gibbsite precipitator was investigated for three different micromixing states, namely maximum mixedness (MM), complete segregation (CS), and maximum mixedness of the fluid but complete segregation of the particulates (MMF-CSP). The influence of the micromixing on continuous precipitation of gibbsite was studied at different precipitation conditions via simulation. Three different cases were considered with respect to the precipitation kinetics: (1) gibbsite secondary nucleation is favoured with slow crystal growth and agglomeration rates; (2) gibbsite crystal agglomeration and growth are dominant mechanisms with secondary nucleation suppressed; and (3) gibbsite crystal growth is the only relevant phenomenon. Simulation results for the cases (1) and (3) showed that the crystalline products for both the MM and MMF-CSP micromixing states were very similar, but the product obtained from the CS micromixing state was considerably different. This indicates that at those precipitation conditions the fluid micomixing has the dominant effect on the product properties, and the particulates micromixing effect is insignificant. However, when operated under the conditions of fast crystal growth and agglomeration kinetics, i.e. case (2), both the fluid and the particulates micromixing were found to affect the precipitation process, resulting in a significantly different product. Computational Analysis in Hydrometallurgy 35th Annual Hydrometallurgy Meeting held in conjunction with the 44th Annual Conference of Metallurgists ofCIM Calgary, Alberta, Canada Edited by

Jan 1, 2005

By Peter McGoldrick

This Talk ?Australian deposits in world context ?Geological setting: the importance of the basin fill ?Key deposit features using HYC (McArthur River) and Century as examples ?The difference between Aussies & Canuuks(that is between Australian & Canadian sedexdeposits!) ?Timing of mineralization ?Sources for metals and ore fluids ?What makes a super giant sedexdeposit?

May 1, 2006

By R. W. Seedsman

In 1984 and 1985, two 7.6m diameter TBM tunnels were driven from the Donkin-Morien peninsula in Nova Scotia to access the Harbour coal seam. The design of the ground support was based on identifying zones of rock failure through the application of the Hoek Brown failure criterion and the early use of finite element analyses. In 1992, the mining project was abandoned and the tunnels allowed to flood. Monitoring data from the tunnel was subsequently used as a case study in the development of the concepts of brittle rock behaviour. In 2007, the tunnels were pumped out as part of a feasibility study into the reintroduction of longwall mining into the coalfield. There is a good match between observations of the collapse zones in the roof and sides of the tunnel and a simple elastic analysis using brittle parameters, a spalling limit of 5, and a low independent shear modulus. The brittle analyses form the basis of the design for the resupport of the tunnels.

May 1, 2009

By Ken Wood, Luc Duval

"The development and operation of the milling circuits treating the different Selbaie orebodies are discussed in this paper. The project is reviewed from metallurgical evaluation through construction to present operating status. The current flowsheets are described, with discussion of some unusual features.IntroductionThe Selbaie concentrator commenced initial production in August 1981, treating underground B zone copper ore in a single 1500 t/d circuit. Throughput was increased to 1650 t/d in 1985. The mill was expanded in 1986 to treat ore from the A-I zone open pit; an independent circuit was added to selectively treat 5000 t/d of copper-zinc ore. Current total mill throughput through both circuits averages 7200 t/d with the production of approximately 270 t/d of copper concentrate and 230 t/d of zinc concentrate.This paper describes the stages involved in bringing the project from initial laboratory testing to its current status as one of the most important producers of silver, copper and zinc in Quebec and a major employer in the region."

Jan 1, 1990

The Discrete Element Method (DEM) is a powerful tool for analysing the flow of charge, the energy consumption and the pattern of energy utilisation of a SAG mill. With the development of laser scanning measurement, the detailed internal working surfaces of a SAG mill can now be included in DEM models. Using scanned results for new and worn shell liners for a 32? (9.75 m) SAG mill, it is shown that the feed and discharge lifters have significant effect on the flow of the charge introducing significant threedimensionality. The effects of the resolution accuracy of liner geometry and the lower cut-off of the rock size distribution are explored. Finally, using a matched new and end of life worn liner and operating conditions taken from site surveys, the effect of wear on charge motion, distribution and energy utilisation are evaluated.

Jan 1, 2012

By C. J. Newman, D. J. Kemp, R. M. Sweetin

"The smelter is described by area; feed preparation, continuous furnace line, gas handling and auxiliary systems, blister refining, Hazelett casting of thin anodes, and scrap remelting. Early smelter campaign data is presented and compared to design. Some modifications to the basic design of the furnaces and gas trains are indicated, with their respective impacts on improving smelter performance.Plant compactness, the use of jumbo tanks, and a highly automated electrode handling system are featured in the refinery description, with brief coverage of the liberator and slimes leaching sections. Early experience in refining thin regular Hazelett anodes, and submersible pump recovery of raw slimes are relayed, together with automatic stripping from titanium blanks.Refinery tonnages and operating parameters are given showing the relatively trouble-free attainment of refinery design performance.IntroductionPrevious papers and articles ( 1), (2) ,(3 ) have described the metallurgical facilities serving the copper-zinc-silver Kidd Creek orebody located near Timmins, Ontario. For convenience a brief review of their mid-1983 operating status is presented.The concentrator, originally designed for 9,000 short tons, was commissioned in late 1966. It can now comfortably process over 13,000 metric tonnes per day largely as a result of the addition of a fourth circuit in 1978."

Jan 1, 1984

By Tim Watson

Andacollo Hypogene Project ?Overview Project description: Sulphide copper concentrator Throughput:55,000 tpd Location: Approximately 50 km from La Serena Elevation: Approximately 1,000 m ASL Start feasibility study: July 2005 Start of construction: May 2007 Construction completion: December 2009 Final cost(1,2,3):435 Million US $ (1) Excludes third party costs, 220 kV power line (2) Cost is based on a Chilean Peso to US Dollar foreign exchange rate of 535 to 1 (3) Does not include US$40.3 million for the Elqui River Pipeline Project or US$8.0 million for the stock pile cover

May 1, 2010

By F. King, R. Sutherby, J. Been

With thousands of kilometers of buried oil and gas pipelines throughout the country, carrying flammable, high-energy hydrocarbons, the integrity and safety of this transportation and distribution network are paramount. The pipeline industry has the primary responsibility for pipeline safety and has in many ways taken the lead in dealing with safety issues. Over recent years, regulatory demands have increased, requiring operators to comprehensively evaluate their pipelines through indirect and direct inspections and to manage risk through integrity programs. Mechanistic and correlative models have been developed that assist in the prediction of pipeline integrity and the determination of reassessment intervals. These lifetime prediction models are based on decades of laboratory research as well as pipeline operating data, material data, and field monitoring data pertaining to soil conditions and CP. An overview is presented of an integrated approach towards the development of such models for the evaluation of external cracking and corrosion of transmission lines.

Jan 1, 2005

By H. E. Lake

VERY EARLY in the initial stages of underground development work at Eldorado's Beaverlodge operation, the decision was made to use mill tailings as a backfill product. Mining and milling commenced in June, 1953, using locally available sand as backfill, while test work and installation of a plant was carried out to prepare ?and deliver the tailings to the mining areas. The first use of tailings was made in February, 1954, a sandslime separation being carried out with hydraulic cyclones. To date (January. 1956), approximately l 40,000 tons of fill have been used in the stoping areas, providing very effective support in a 50 deg. Vein system of cut-and-fill mining. The recoverable portion of the mill tailings amounts to 40 to 45 per cent, which has resulted in a product giving a percolation rate of 6 to 10 inches per hour. Owing to the fact that Eldorado has milled from 15 to 2 5 per cent more ore than it has mined, through the purchase of custom ore, the degree of control on the sand-slime separation has not been as critical as it might normally be when the filling operation must depend only on the tailings from ore mined. A description of the conditions involved and of the plant as finally installed is given below. It might be mentioned here that, with the impending increase in milling capacity from 700 tons to 2,000 tons p.er day, the present plant will be considerably altered within the ensuing year to handle the increased tonnage and distribution.

Jan 1, 1956

By Derek H. C. Wilton

"The Cape Ray Fault Zone of southwestern Newfoundland contains two notable electrum/ base metal sulphide quartz vein lode occurrences hosted by two contrasting lithological units, viz. a graphite schist horizon and a granite. The two occurrences, although in proximity, are not in direct contact, but, based on geochronological, geochemical and isotopic evidence, they were apparently deposited from hydrothermal fluids generated as a vapour phase from the magmatic progenitor of the Windowglass Hill granite.This paper provides further evidence, from REE and background A u and Ag data, for the magmatic origin of the hydrothermal fluids. Wall rocks to the electrum-bearing quartz veins in both the schists and granite have experienced a LREE depletion probably due to leaching by Cl-bearing solutions. Gold and silver contents are typically low in all rock types but there is a slight elevation in gold concentrations in those units in contact with the Window glass Hill granite. The granite also has the relatively highest gold and silver contents of any unit in the region.IntroductionThis paper presents the evidence from rare earth element (REE) and gold/silver concentration data for the magmatic origin of hydrothermal fluids responsible for deposition of the Cape Ray electrum deposits of southwestern Newfoundland. The two deposits occur in the Cape Ray Fault Zone (Fig. I) within the Windsor Point Group and Window glass Hill granite. The larger occurrence is called the Main Shear Showing and consists of a deformed quartz vein horizon, which extends for - 6 km, within the late Devonian Windsor Point Group. This unit is an intermixed ignimbrite and mafic tuff sequence with associated schists (metasediments) and gabbros. The host rocks to the mineralized quartz veins are interleaved graphite, chlorite and sericite schists. Basal ignimbrites within the Windsor Point Group have been dated, by Rb/Sr isotopic methods, at 377 ±21 Ma (Wilton, 1983a). The basal ignimbrites also have enriched REE patterns, an elevated initial Sr ratio (0.709) and a peraluminous-siliceous nature which suggest they resulted from the partial melting of continental crust (Wilton, 1984)."

Jan 1, 1985

An Attractive Investment ?Near term low cost and secure PGM producer ?restricted supply legislated demand ?strong pipeline of resource development ?Building Canada?s largest undeveloped PGM-Cu resource ?All work (resource, reserves, DFS, EA) is NI43-101 compliant ?Strong balance sheet: over $8 m in cash with no debt

May 1, 2010

By H. Henao, E. Kohnenkamp, L. Rojas

The slags generated in the copper conversion process are mainly composed of Cu2O-Fe2O3-SiO2 with the compounds CaO and Al2O3 in concentrations up to 10 wt%. The present work contributes to the knowledge of the conversion process, generating experimental data for the diagrams of phases Cu2O-Fe2O3- SiO2-Al2O3 and Cu2O-Fe2O3-SiO2-CaO. The experiments were carried out in a tubular furnace at temperatures of 1150°C and 1200°C under a condition of saturation with tridymite. Once the equilibrium was reached, the samples were fast quenched in water. The phases in the samples were observed in a Scanning Electron Microscope (SEM) and the elemental composition of the phases analyzed by means of Energy-dispersive X-ray spectroscopy (EDS) detectors. The addition of Al2O3 and CaO into the Cu2O-Fe2O3- SiO2 system resulted in an appreciable displacement of the liquidus lines, corresponding to an expansion of the liquid in the tridymite primary phase field. INTRODUCTION The conversion process of copper consists of oxidizing Fe and S present in mattes with 60 to 65wt% Cu (up to 16wt% Fe). This process is separated into two stages: 1- Slag blowing: Fe is oxidized, the addition of a flux such as SiO2 (silica) forms a second liquid phase called slag, this phase is removed from the furnace; 2-Copper blowing: in this stage, the matte with low concentration of Fe (<1% w/w) is again oxidized to remove S as SO2 in the exhaust gases. The product of these two processes is the formation of Copper Blister (> 98wt% Cu) (Schlesinger et al., 2011). Unlike the aforementioned conventional processes, in most Chilean smelters, conversion Peirce- Smith Furnaces are loaded with high copper matte (70–75wt% Cu) (Henao & Moyano, 2016). Due to the low concentration of iron in these matte (up to 5wt%), it is considered that separating the conversion process in two stages is neither operational nor environmentally convenient. Therefore, the process is carried out in a single stage (Pradena et al., 2006), generating a slag phase with a high percentage of Cu2O (wt%Cu>40).

Jan 1, 2019

By Donald A. Cranstone

"This paper provides a bird&apos;s eye view of the pattern of gold discoveries since 1823, the year of Canada&apos;s first gold find, up to 1983. Within this 160-year period, more gold was discovered in Canada during the last ten-year period (1973-1982) than during any previous decade. The record suggests that the potential for further major gold discoveries is high, which bodes welt f or the future of Canadian gold mining.IntroductionCanada has an impressive history as a gold producer. Since 1921 we have occupied second or third place among the world &apos;s gold producing nations, after South Africa and most of the time the U.S.S.R. Canadian gold production over the last hundred years has added up to some 6 per cent of all-time world production.The sharp rise in the price of gold in the 1970s led to a surge of gold exploration, which in turn resulted in the discovery of significant quantities of gold in Canada. How do these recent discoveries rate in comparison with those of the more distant past? For example, are the quantities of gold in notable discoveries of recent year s, such as Hemlo and Detour, in the same league with the amounts of gold discovered around 1910 in the Porcupine and Kirkland Lake district s of Ontario? Can the combined gold content of the recent discoveries be likened to that o f the almost 40 major Canadian gold deposits, along with numerous smaller ones, discovered in Canada during the 1920s and 1930s? What are the implications of the more recent gold discovery record for future rate s of gold discovery in Canada?This paper attempts to glean answers to such questions from an overview of the period that begins in 1823, the year of Canada&apos;s first gold discovery. Gold deposits come in two major types: placer deposits and lode deposits in solid rock . Placer gold is distributed in sand and gravel. Gold in solid rock occur s mostly in gold ore filling fissures."

Jan 1, 1985

By J-P. Rossetti, A. Guerin, M. Jaboyedoff, L. Baillet, A. Mariscal, J. D'Amato, D. Hantz

"The processes leading to the fall of rock compartments from rock walls are poorly known as well as their velocity. It ensues that quantitative prediction of the failure time for a rock compartment which is presently stable, is not possible by a purely geomechanical approach. However a quantitative probabilistic prediction of rockfalls at the scale of a rock wall is possible if the spatial-temporal rockfall frequency can be determined or estimated (Hantz, 2011). For a better knowledge of failure processes and frequency, rockfalls have been detected in several rock walls, using annual terrestrial laser scanning, allowing comparison of the frequencies in different geological conditions. For one of these rock walls, the spatial detection have been completed by a precise dating of the events, using a quasi-continuous photographic survey (one photo every 10 mn), allowing the study of the influence of meteorological factors.The precise dating of rockfalls has been carried out for the Saint-Eynard cliff which towers above a residential area of the town of Grenoble (French Alps). The South-East facing cliff consists in bedded limestone gently dipping North-West and located at an elevation between 850 m and 1100 m. The surveyed zone is about 750 m large and 250 m high. Between 01/02/2013 and 26/11/2013, 65 rockfalls ranging between 0.01 m3 and 20 m3, have been detected by diachronic comparison of laser scanner data and dated by comparison of photographic images. The temperature at the elevation of the cliff has been calculated from the temperature measured (every 5 mn) at a meteorological station located at an elevation of 245 m and 2.5 km away from the cliff, using a temperature gradient of 0.003°C/m (D’Amato et al., 2014). The precipitation were measured 900 m away from the cliff at an elevation of 469 m. Different meteorological conditions have been defined: (a) “freeze” qualifies days with negative mean temperature (but with a thaw period, except for two days); (b) “thaw” qualifies days with positive mean temperature, but following a freeze day; (c) “rain” qualifies days with precipitation.Table 1 shows the rockfall temporal frequency for the different meteorological conditions. It appears that the frequency is about 6 times higher the freeze days, 2.5 higher the thaw days and 3 times higher the rain days than days without freeze, thaw or rain."

Jan 1, 2015

By Matthew Russell, Bobby Randhawa, Leopoldo Mariscal Samaniego, Jose A. Puente, D. Brosig, Paykan Safe

The La Caridad copper smelter, located in Nacozari, Mexico, have started a multi-year plan to reduce sulfur dioxide and particulate matter emissions into the environment. In 2014 the smelter completed a voluntary plant-wide SO2 process emissions inventory as part of the smelter’s proactive environmental stewardship policy. In turn, this triggered the development of several environmental projects to alleviate these emissions. A strategy consisting of improved capture efficiency of the sources with greatest impact has been followed to maximize cost-effectiveness. The reduction of secondary emissions from the Teniente Converter, as well as of primary and secondary emissions from the Peirce-Smith Converters have been key areas of priority. Additionally, a new system to capture and recover particulate matter from the Anode Refining Furnaces off-gas is also in the process of being implemented. This paper presents an overview of the work developed behind this effort and the smelter’s vision towards a greener future. INTRODUCTION The La Caridad copper smelter is owned and operated by Metalurgica de Cobre S.A. de C.V. (a subsidiary of Grupo Mexico). Currently, the smelter has a production capacity of 300,000 tonnes of anodic copper per year. The smelter is coupled with a 300,000 t/y electrolytic refinery. Other by-products (such as precious metals and sulfuric acid) are also generated as part of an integrated process. The original smelter started operating in 1986 with one Furukawa concentrate dryer, one Outokumpu Flash Smelting Furnace (FSF), two slag cleaning electric furnaces (SCFs), three Peirce-Smith Converters (PSCs), two Anode Refining Furnaces (ARFs) and one casting wheel. In 1997, a plant expansion project was concluded with the installation of one steam dryer, one Modified Teniente Converter (MTC), one additional ARF, one additional casting wheel, and the electrolytic refinery [1]. Over the years, the smelter management has implemented numerous environmental projects to alleviate SO2 and particulate matter (PM) emissions. The smelter process gas handling system captures the process gases from the FSF, MTC, and the three PSCs. The process gases are cleaned and conditioned and sent to the two acid plants. The first acid plant (with a capacity of 226,000 Nm3/h, wet basis) was commissioned in 1988 to process the FSF and PSC off-gases. A second acid plant (with a capacity of 195,000 Nm3/h, wet basis) was commissioned as part of the smelter expansion project [1]. The PSCs also have a secondary gas handling system with a dedicated baghouse and stack. The Furukawa dryer off-gas reports to a dedicated electrostatic precipitator (ESP) for dedusting before venting via a local stack. Process gas from the two SCFs, along with hygiene ventilation from various sources inside the smelter (including matte and slag tapping hoods from the FSF) report to a baghouse-based gas handling system and vent to atmosphere via a local stack. The original ARFs do not have an off-gas handling system, however, each ARF has a post- combustion chamber which naturally vents the process gases to the atmosphere via a dedicated stack.

Jan 1, 2019

By A. Ojaghi, A. R. Mohammadi

"The Marvast monazite deposit is located 35 kilometres south - southwest of Marvast in Yazd province of Iran. A representative sample weighing approximately 10 tons was prepared to study the amenability of the ore to physical beneficiation. The size fraction of +1000 µm was removed due to low monazite content and the –1000 µm size fraction was concentrated by the gravity-classification-magnetic methods. According to the results of sample characterization, the representative sample contains 220 ppm REO that is contained in monazite. It was concentrated to 41.5% REO by the above mentioned methods. The recovery of REO in the monazite concentrate was 41.5%.INTRODUCTIONRare earth elements are critical metals in many countries (Gupta, 2005; UK Geological Survey, 2011). Increasing application of these metals in hi-tech industries and price fluctuation caused by Chinese production policy has led other countries to focus on their local resources (UK Geological Survey, 2011). In this case, Iran is not an exception.REE mineralization in Iran is mainly located in the central zone. Regarding the exploration data, these deposits are divided into two categories. The first group is iron ore deposits in which the REE are carried by phosphate minerals. The other group is placer deposits where monazite is the major mineral of the deposit. The Marvast placer deposit is one of these types of deposit (Daliran, 1990; Mokhtari, 2008; Torab, &Lehmann, 2007; Alipour, 2014)."

Jan 1, 2016

By R. M. Bustin

"Extensive deposits of tectonically sheared coal of the Mist Mountain Formation occur in the south eastern Canadian Cordillera. The quality of the coal varies markedly; it is commonly partially oxidized and poor washability characteristics.Oxidation of the sheared coal has been promoted by its fine grain-size and by fractures in adjacent rocks which have facilitated penetration of atmospheric oxygen and circulation of oxygenated waters. Oxidation has resulted in a loss of coking power, a decrease in vitrinite reflectance, and an Increase In oxygen and decrease in carbon content.The relatively low clean coal yields of the sheared coal are primarily the result of the greater volume of mineral matter present, which in turn reflects both the greater susceptibility to shearing of coal with abundant rock partings and the shearing and dissemination throughout the coal of formerly discrete rock partings. The high ash content of some sheared coal seams may be artificial, resulting from the difficulty in distinguishing and separating sheared roof rock and floor strata from the coal seam during mining. There is little variation between the quality of the washed sheared and unsheared coal, with the exception of the somewhat higher ash content of the clean sheared coal compared to clean unsheared coal. This poorer separation of the ash from the organic fraction of the sheared coal is considered to be a product of the large amount of fines present as well as the local formation of aggregates of organic material and ash resulting from plastic flowage of the vitrite and clarite during shearing.IntroductionIn the southeastern Canadian Cordillera, coal seams of the Lower Cretaceous Mist Mountain Formation (Gibson, 1979 were in part sheared and comminuted during Late Cretaceous and Tertiary tectonism . Extensive deposits of sheared coal exist, and even in areas of mild deformation the coal may be locally sheared (Bustin, 1979). The quality of the sheared coal varies notably; it is commonly oxidized even far from the present weathering horizon, and locally has a disproportionately large amount of ash and poor washability characteristics even far from the present weathering horizon and locally has a disproportionately large amount of ash and poor washability characteristics."

Jan 1, 1982

By Y. Wang, J. D. Miller, C. L. Lin, Virginia Tech

Conventional flotation machines are typically limited to a particle topsize of 150-200 microns due to inherent constraints created by the pulp and froth phases. To overcome these limitations, a novel fluidized-bed flotation system called the HydroFloatTM Separator has been developed specifically for the purpose of floating coarse particles containing only small amounts of exposed hydrophobic minerals. Over the last decade, this technology has been successfully applied to industrial minerals with several full-scale units installed to recover particles up to and exceeding 3,000 microns diameter. More recently, sulfidebased test work has shown that this novel device is also capable of recovering metalliferous values at a grind size that is much coarser than currently used in industrial concentrators. In the current study, high resolution X-ray microtomography (HRXMT) was used to experimentally compare the degree of exposed grain surface area necessary to recover coarse particles using the HydroFloatTM technology to that attainable using a traditional mechanical flotation cell. The data indicate that exposed grain surface area is a critical factor for coarse particle flotation. For the gold-bearing sulfide ore examined in this study, the HRXMT data suggest that near complete recoveries of coarse (850x500 µm) multiphase particles containing as little as 1% exposed grain surface area were realistically attainable using the HydroFloatTM technology. As such, this new technology may offer a unique opportunity for increasing concentrator capacity by increasing the primary grind size needed for rougher/scavenger separations.

Jan 1, 2016

By S. Banisi, M. Pourkani, A. R. Laplante, A. Partoazar

"Canadian experience in industrial modeling of grinding, classification, and flotation kinetics was applied at the Sarcheshmeh copper mine, which processes 40,000 t/d of ore at 0.9 % Cu, in an effort to improve capacity and metallurgical performance. Mcivor's functional performance analysis was applied to ball mill cyclone circuits to maximize circuit capacity. Plitt's cyclone model was applied to predict how apex wear would affect classification performance, as part of a predictive maintenance program whereby the optimum wear period is determined for cast iron apexes. The flotation flowsheet was improved using Agar's optimization criteria. The impact of these technologies has been nothing short of spectacular, with an improved capacity of 1 S to 20""/o, and increased recoveries.1-IntroductionThe Sarcheshmeh copper ore body, which may rank as third or fourth largest in the world, contains 1 billion tonnes averaging 0.90 % copper and 0.03 % molybdenum. It is located southeast of Iran and has been processing 40,000 t/d of ore since 1982. The mine produces 100,000 tonnes of copper and 2,200 tonnes of molybdenum concentrate per year. After three stages of crushing, the ore with a Fso of 12. 7 mm is fed to 8 parallel ball mills in closed circuit with cyclones to produce a product 70""/o finer than 7 S microns. The concentrate of the first stage of flotation is reground and the tailings constitute the main component of the plant final tailings. A concentrate with an average grade of 31 % Cu is obtained after cleaning and re-cleaning stages. Total recovery of the plant varies between 83 and 87 % depending on the operating conditions and ore type.To improve the overall performance of the plant, it was first decided to evaluate the performance of grinding, classification and flotation. Measures were then taken to improve performance using the following criteria: (i) The improvements should be of the types that have resulted in significant improvements in other plants (e.g. Shannon et al, 1993); and (ii) The proposed improvements must be achievable with the manual operation presently used at Sarcheshmeh. The outcome of this study could also help in making decisions on the implementation of automatic control systems in the Sarcheshmeh copper mine."

Jan 1, 1998

By Eamonn F. Maher

Superconductivity is one of the most remarkable scientific phenomena ever investigated. It is the phenomenon whereby some materials exhibit zero resistance to the passage of an electric current when cooled to low temperatures, and requires a quantum mechanical explanation. Four Nobel prizes in physics have been awarded specifically on the subject of superconductivity, with many more enabled by superconducting technology. For example, particle beams are generated in accelerators and manipulated in ?particle beam lines? in the ?Big Physics? projects around the world eg. at CERN, Geneva, leading to major discoveries in fundamental particle physics. Similarly, at the JET Propulsion laboratory near Oxford, U.K, controlled nuclear fusion has been demonstrated, and magnetic containment of plasmas is key. In the chemical and biological sciences high field NMR spectroscopy has become indispensable for examining organic matter, revealing the mysteries of the workings of cells, genetics, and in the development of new polymers and pharmaceuticals. With all these very advanced uses for superconducting magnets, it is easy to forget that superconductivity is big business, not just a scientific curiosity. MRI (Magnetic Resonance Imaging) superconducting magnets, the key component of high resolution body scanners, use approximately half of the world?s superconducting wire ? the other half being mostly used in accelerator magnets. The MRI market is about 3 billion dollars per annum, and one MRI magnet uses 200km of wire. New applications for superconducting magnets are now appearing including ?Catheter steering?, enabling much shorter timescales for life-saving brain tumour removals and ?Functional MRI?, a whole new area in patient diagnostics. Whilst the use of low temperature superconductors (LTS) is now well established commercially in superconducting magnets and niche electronic applications, the application of LTS in electric power distribution and transport has been very limited to date. It is now more than fifteen years since the so-called High Temperature Superconductor (HTS) materials were discovered: these can be operated at liquid nitrogen temperatures rather than liquid helium temperatures. However, materials processing and scale-up issues have prevented their widespread use, and in particular the required price/performance criteria are only beginning to be reached except in certain niche markets. BSCCO (Bismuth Strontium Calcium Copper Oxide) tapes up to one km long are now readily available, and have been demonstrated in high current cables for power distribution networks, but the general consensus is that 1) it is difficult to reduce the price much further because of the silver matrix required and 2) in applications where coils are required eg. motors, generators, transformers etc the properties of BSCCO are rather poor because of the critical current dependence on magnetic field. Magnetic fields are always associated with coils and windings, and such fields are of course fundamental to the operation of all electrical machines. YBCO (Yttrium Barium Copper Oxide) however, has good characteristics in field and for the last few years there has been intensive research and development costing several tens of millions of dollars worldwide into the scale-up of production of so-called ?coated conductor?. This ?second generation? tape can be produced by any of many different film deposition techniques, with more or less success for short lengths, but as yet it is unavailable in lengths more than a few tens of metres.

Oct 1, 2003