Search Documents

By Craig H. B. Leitch

"In describing the alteration of porphyry systems, the term ""secondary K-feldspar"" appears to be an oversimplification. A better term would be ""alkali feldspar"" alteration, because in actual fact the replacement feldspars show gradational changes from an albite, which is important in some systems, to an alkali feldspar containing minor orthoclase molecule, to true orthoclase.There are several textural varieties of secondary alkali feldspar present in the porphyry systems studied from British Columbia, Australia and New Zealand. These include, in apparent increasing order of alteration intensity: clear albite (An10); patchwork albite (An5-10); chessboard albite (An0-10); ""irregular albite "" (An0Ab100 to Ab90Or10); untwinned ""anoralbite"" (Ab90Or10 – Ab70Or30); and orthoclase (Ab40Or60 - Or100)·The exploration significance of these varieties of alkali feldspar is that their gradation in composition, from sodic to potassic, may be linked to a corresponding increase in intensity of alteration. Thus, there is a tendency for more sodic alteration feldspars to characterize weak, sub-economic deposits, or the fringe zones of stronger deposits; the more potassic alteration feldspars may provide an exploration vector toward more highly mineralized zones."

Jan 1, 1981

By Craig H. B. Leitch

"In describing the alteration of porphyry systems, the term ""secondary K-feldspar"" appears to be an oversimplification. A better term would be ""alkali feldspar"" alteration, because in actual fact the replacement feldspars show gradational changes from an albite, which is important in some systems, to an alkali feldspar containing minor orthoclase molecule, to true orthoclase.There are several textural varieties of secondary alkali feldspar present in the porphyry systems studied from British Columbia, Australia and New Zealand. These include, in apparent increasing order of alteration intensity: clear albite (An10); patchwork albite (Ab5-10); chessboard albite (An0-10) "" irregular albite "" (An0Ab100 to Ab90r10); untwinned "" anoralbite"" (Ab90Or-Ab70Or30); and orthoclase (Ab440Or60-Or100)·The exploration significance of these varieties of alkali feldspar is that their gradation in composition, from sodic to potassic, may be linked to a corresponding increase in intensity of alteration. Thus, there is a tendency for more sodic alteration feldspars to characterize weak, sub-economic deposits, or the fringe zones of stronger deposits; the more potassic alteration feldspars may provide an exploration vector toward more highly mineralized zones."

Jan 1, 1981

By William A. Napier

The Mantaro Phosphate Property is located ~ 250 km east of Lima, Peru in the Andean altiplano near the city of Huancayo, Junin District. The Mantaro deposit is a mineralized zone of phosphatic rock currently defined by surface outcrops, trenches and drilling extending over a strike length of more than 30 km and a width of more than 5 km covering ~27,700 hectares. Mineralization is exposed as three roughly parallel exposures (?mantos?) trending in a northwest-southeast direction along the Mancaspico syncline. Estimated mineral resources1 contained in Manto 1 of the Property (4% P2O5 cut-off) as of February 21, 2010, are: Measured 5.548 million tonnes @ 10.8% P2O5 Indicated 33.975 million tonnes @ 9.9% P2O5 Measured + Indicated 39.523 million tonnes @ 10.0 % P2O5 Inferred² 376.265 million tonnes @ 9.0% P2O5 1Tonnes rounded to the nearest 1,000 and grade to 1 decimal place. 2Inferred material reported with no cut-off and an assumed grade. There is considerable potential to expand the resource base. Mantos 2 and 3 of the deposit have been geologically mapped and exhibit surface mineralization widths similar to Manto 1. Given that the deposit is of marine sedimentary origin, it is reasonable to infer that comparable grades and depth of mineralization are present within Mantos 2 and 3. Based on this assumption, the potential mineral deposits within Mantos 2 and 3 are estimated to be approximately: Manto 2 425-435 million tonnes @ 9% P2O5 Manto 3 280-290 million tonnes @ 9 % P2O5 These potential quantities and grade are conceptual in nature, there has been insufficient exploration to define a mineral resource and it is uncertain if further exploration will result in these targets being delineated as a mineral resource. However, should such conceptual resources be confirmed by trenching and drilling, the Mantaro Phosphate Property would rank as one of the most significant phosphate deposits in the world.

May 1, 2011

By Vincent Doyon

For several years, the GDD SSW EM Probe is being used in nickel?s mines in Canada and Brazil to define ore limits, reduce dilution and predict nickel grades. It is used with success to test most if not all percussion blast holes at all Falconbridge Mines in Sudbury and Raglan and all Inco?s Thompson mines. However, after testing the SSW Probe in other metal mines, we realized that EM conductivity does not define ore limits by testing blast holes for copper, zinc or gold. For non-conductive ores, no instrumentation is yet available on the market to reduce dilution, by outlining quickly and inexpensively the real shape of an orebody. To that effect, Instrumentation GDD Inc has developed a new revolutionary photonic probe that will make the reduction of dilution possible by probing blast holes. Once surveyed with the probe, a computer draws graphs of the ore grade as a function of depth for each blast hole. A contribution by Canada Economic Development made possible the development of this new technology. Canmet and Soredem also cautioned this technology developed by Instrumentation GDD Inc. This new photonic probe will allow: 1) to better understand the shape of the orebody 2) to raise the grade of the ore fed to the mill 3) a more complete extraction of the ore 4) to raise the competitiveness of mines

Oct 1, 2004

By Matthew Violot

Vale Canada?s Birchtree Mine, located in Thompson Manitoba, has been experiencing problems with hanging wall / footwall dilution, as well as sloughing off of adjacent stopes and temporary stope block backs. Birchtree Mine is interested in determining how time affects the stability of their open stope blocks. Many factors simultaneously influence open stope stability (rock mass quality, joint condition, stress condition). This makes it challenging to determine the influence of a single parameter such as exposure time or stand-up time. This study focuses on determining the effect of exposure time on open stope dilution and combines stress analysis and empirical based approaches.

Jun 1, 2012

Training by Inclusiveness ?Background ?Video ?Results ?Partners ?How SEM works ?Future of SEM Background: Inclusivity partners ?Northwest Community College ?Smithers Exploration Group ?With support from the Province of BC ?Federal government ?And First Nations across the northwest

May 1, 2010

By O. Laitinen, M. Rudolph, J. A. Sirviö, H. Liimatainen, R. Hartmann, University of Oulu

The increasing complexity of the ores composition worldwide calls for suitable collectors with specific properties, such as selectivity, wettability, and in regard to current regulations, environmental sustainability. Therefore, collectors have to satisfy many features to improve the efficiency of flotation processes. Cellulose nanocrystals gain more and more interest due to the versatile synthesis routes which enable the integration of specific functional groups and components with different degrees of hydrophobicity within the molecular structure. Consequently, cellulose nanocrystals can be employed in flotation processes as depressant or collector molecules, respectively. Nonetheless, the usage of cellulose nanocrystals is still limited due to a lack of the characterization of nanocrystal-mineral interactions and the change of the surface wetting properties of minerals after adsorption phenomena between nanocrystals and minerals. In these studies, butyl-amine cellulose nanocrystal (BAC) and quartz are used as model system to investigate physicochemical properties of both, BAC and quartz, and examine the applicability of BAC in flotation processes. Therefore, the surface charge distribution and electrophoretic mobility of BAC and quartz are investigated and compared to understand the effect of electrostatic interactions between BACs, and BAC and quartz. Based on this, the adsorption of BAC on quartz is examined. Finally, microflotation experiments test the efficiency of BAC to be used in flotation processes. The flotation response is correlated to the specific surface charge of BAC revealing the dominant effect of surface charges on effective particle-bubble adhesions.

Jan 1, 2016

By J. -P. Tshibangu, M. Ramos da Silva, F. Descamps, C. Schroeder, J. -C. Verbrugge

"The mechanical behaviour of rock materials is largely influenced by the stress state and pore pressure; this needs to be considered in many applications, such as petroleum engineering, tunnelling or stability of underground excavations.Conventional triaxial tests (d2 = d 3) are generally used to assess the influence of confining and pore pressure. In this work, those tests are performed on a porous rock named Sorcy limestone, along with more advanced stress paths like triaxial extension (d 2 = d 1) and purely deviatoric tests with independent pore pressure control. Those tests are combined to a true triaxial study on the dry rock in order to investigate the effect of true triaxial stresses and, hence, build three-dimensional limiting envelopes accounting for the influence of pore pressure.Three-dimensional limiting envelopes of dry Sorcy limestone are built in meridian and octahedral planes. The shape of the octahedral sections changes with the mean stress from triangular to hexagonal and then quasi circular. At even higher mean stresses, the evolution continues towards a triangle with apexes oriented in the direction of triaxial extension stress states. In meridian sections, the deviatoric stress first increases with the mean stress. The transition between this deviatoric mechanism and the cap surface occurs at different mean pressures depending on the Lode angle.Terzaghi’s effective stress is found to govern the yield and plastic behaviour of saturated Sorcy limestone. Triaxial tests show that the limiting envelope does not depend on the loading path (conventional compression and purely deviatoric stress paths). In triaxial extension, the brittle-ductile transition is observed for a higher mean pressure than in triaxial compression, as previously found for true triaxial tests on the dry rock.Finally, it is shown that upon appropriate normalisation, the dry and saturated yield envelopes come very close one to each other. This suggests that only the size of the yield envelope changes between dry and saturated state (pore pressure = 5 MPa); its shape does not seem to evolve."

Jan 1, 2015

By Arthur D. FitzGerald

EDC established an Environmental Review Framework in 1999. Throughout the early fall of 2001, the Corporation held public consultations across Canada to strengthen that framework, leading to a public release on November 15, 2001 of a report summarising the results of these consultations. Following this, the Corporation implemented strengthened environmental review requirements in the form of its Environmental Review Directive, in compliance with legislated amendments to Canada?s Export Development Act that went into effect on December 21, 2001. Over the past few years, there has been a global trend towards an increase in the social and environmental requirements of multilateral/bilateral financial institutions and export credit agencies. More recently, this activity has focussed on capturing institutions that have not yet adopted similar requirements and, more specifically, on developing a convergence of the requirements from institution to institution. This paper describes EDC?s new ERD and some of the initiatives that have taken place or are in process that are moving international financial institutions toward converging their environmental and social requirements for projects in the private sector.

May 1, 2002

By Matt Manson

Diamonds in Canada: Recent Advances in Exploration Methodology and Advanced Stage Assessment 1. Exploration Methodologies ? Prospectivity Mapping ? Surficial Geochemistry ? Geophysics 2. Advanced Stage Assessment ? Petrology and Diamond Paragenesis ? Micro/Macro ratios and Macro grades ? Value Sampling and Modeling

Apr 1, 2005

By K. Barbetti

"The carbon-in-pulp (CIP) process has been the dominant gold recovery process since the early 1980s. CIP has proven to be very adaptable for a wide range of ores and circuit configurations. The key performance indicator for CIP circuits is the minimisation of soluble gold losses to tailings, however, it is also important to operate the circuit efficiently (maximising gold loadings on carbon and minimising carbon inventory). Over the last 30 years the Curtin Gold Technology Group has studied CIP circuits as part of an on-going collaborative industry funded project (the AMIRA Gold Processing Technology Project). In the early years the project undertook basic research into understanding activated carbon, and its management in the circuit. More recently the development of process models and instrumentation has provided additional tools to assist operators. The results show that while most CIP circuits operate well, there are still significant opportunities for further cost savings, or additional revenue. This paper reviews the observations arising from this work, including key requirements for good carbon management, the results of benchmarking and industry surveys of carbon circuit over 20 years, the value of process modelling of CIP circuits to establish operating parameters, and the use of automated instrumentation to better optimise carbon control in the circuit.INTRODUCTION The introduction of activated carbon to recover gold from cyanide leach solutions in the last quarter of the 20th century was the most significant development in gold ore processing since the advent of cyanidation seventy years before. Replacing the Merrill–Crowe zinc cementation step with carbon-in-pulp (CIP) or carbon-in-leach (CIL) circuits provided a process that allowed the treatment of lower grade and problematic ores (e.g. high-clay ores), at lower capital and operating costs, and higher metal recoveries. The CIP circuit was first developed in the 1950s at the Carlton Mill, Cripple Creek, Colorado. All the components of the modern CIP process came to fruition at the Homestake Mine in South Dakota in 1973 (Fast, 1988). From the late 1970s onward a variation of CIP, carbon-in-leach (CIL) which combined the leach and adsorption stages, became the preferred circuit design in most parts of the word."

Jan 1, 2017

By H. Dundar

An extensive testwork was performed around the HPGR plant at GoldFields Ghana Limited Tarkwa Gold Mine. The HPGR was used to prepare the feed for heap leaching. The circuit was configured in such a way that the edge material from the HPGR discharge was recycled for further crushing while the product from the centre reported to the heap leach section. The set-up of the Polysius HPGR provided an opportunity to study the effect of different design and operating variables. This paper will discuss the results from the tests performed to assess the effect of rolls? speed and applied pressure on the capacity and the grinding efficiency of the HPGR. Applying different pressure values appeared to have an influence on the amount of edge material recycled.

Jan 1, 2012

By A. Miura, R. Winarko, D. B. Dreisinger

Chalcopyrite leaching in acidic ferric sulfate media at ambient temperature exhibits slow kinetics and poor leaching efficiency, which is typically attributed to surface passivation. Recently, the presence of small amounts of iodide in the leaching media has been reported to significantly accelerate chalcopyrite dissolution. To further explore the behavior of chalcopyrite leaching in the presence of iodide, it is essential to determine the factors that control the leaching kinetics. In this study, we investigated the effect of initial solution potential, iodide concentration, particle size, and temperature on the kinetics of copper extraction from chalcopyrite. The key in the experimental setup was to minimize iodide loss by iodine evaporation and precipitation as cuprous iodide. The former was achieved by performing the leaching tests in fully sealed leaching systems. The latter was achieved by maintaining the solution potential higher than 420 mV (versus Ag/AgCl electrode), where formation of CuI precipitate is possible. The experimental results show that higher solution potential and higher iodide concentration had a pronounced positive effect on the rate of chalcopyrite dissolution. There was no effect associated with particle size, which might be due to the narrow size range tested. The positive effect of increasing temperature only manifested itself when the solution potential was sufficiently high. INTRODUCTION The main challenge of chalcopyrite leaching using ferric ions as the oxidant at ambient temperature is the slow kinetics and poor extraction. The reason for this leaching behavior has been attributed to passivation resulting from formation of insoluble passivating layers on chalcopyrite surfaces, which could be metal-deficient sulfides, elemental sulfur, polysulfides, and iron precipitates (Klauber, 2008). To overcome passivation, technologies using higher temperature and pressure have been developed to leach chalcopyrite concentrates, such as the CESL process (Mayhew, McCoy, Mean, & Woeller, 2013), FLSmidth Rapid Oxidative Leach (ROL) process (Mulligan et al., 2017), Galvanox (Dixon, Mayne, & Baxter, 2008), Albion process (Hourn, Turner, & Hourn, 2012), HydroCopper (Hyvärinen & Hämäläinen, 2005), TPOX (Dreisinger, 2006), and AAC/UBC process (Dreisinger, Dempsey, Steyl, Sole, & Gnoinski, 2003). Even though they are effective in accelerating copper leaching kinetics, those technologies typically have higher capital and operating costs associated with production of concentrates and application of autoclaves. This makes them unsuitable for treating low grade primary copper sulfide ores.

Jan 1, 2019

By R. J. Mitchell

"The use of hydraulically delivered classified tailings sands to provide ground support in large mining operations is still widespread despite recent developments of alternate backfilling methods and materials. The major disadvantages of the use of hydraulic fill are the costs and risks associated with slurry delivery. The main risk is that of bulkhead failure resulting from sand liquefaction due to insufficient operational control or due to dynamic loading from earthquake or rockburst. That risk may be eliminated by the pouring of a stiff cemented sand plug in the base of each stope prior to continuous fill pouring in that stope. An additional advantage of cemented plugs is that massive bulkheads are not needed. Instead, a temporary (removable and reusable) bulkhead can be used for plug forming.Physical model studies of fill pressures on a temporary bulkhead were carried out in a 3 m radius centrifuge facility. Fill pouring in-flight was carried out in order to model prototype stress paths. The results indicate that the average bulkhead pressure is likely to be less than 10 kPa under normal operating conditions and less than 20 kPa under the poorest anticipated operating conditions which include smooth walls, high slimes content and high water-content slurries. A portable bulkhead consisting of a central core and a surrounding sealing bladder was modelled and found to be effective. The use of different sizes of cores allowed the stress distribution adjacent to these bulkheads to be evaluated."

Jan 1, 1992

By T. Senga, T. Namihira, S. Terada, S. Owada

"Electrical disintegration (ED) has been well known as a good comminution method to improve liberation of compositional phases because it was reported that electron avalanche could occur preferentially at phase boundary. But the detailed mechanism of the ED has been still not known. This paper describes the results of ED experiments using synthetic binary sample, copper/resin, under the conditions of various distance between electrodes, and discusses the energy distribution in the three kinds of phenomena in the ED process, which are(1) streamer progression in water, (2) electron avalanche in water, and (3) electron avalanche in solid sample, by measuring current and voltage with elapsed time. Then, it has been found that the energy distribution in the phenomenon (1) is quite low and that the distribution in the phenomenon(2) had a considerably large compared with that in the(3), which indicates that the shockwave generated in water could contribute much to the sample breakage.INTRODUCTIONElectrical disintegration (ED) has been well known as a specific comminution technology which enhanced selective breakage at phase boundary and lead to a good liberation among compositional phases1-6),but the detailed mechanism has not been clarified yet. This study describes energy distribution among the phenomena in the ED process by using a synthetic binary sample, copper/resin, the phenomena of which are (1) streamer progression in water, (2) electron avalanche and shockwave generation in water and (3) electron avalanche in solid sample usually at phase boundary. The energy distribution could be calculated from ED experiments and from voltage-current changes between electrodes as a function of elapsed time.SAMPLE AND EXPERIMENTALSampleThe sample used in this paper was a synthetic binary solid of copper/resin as shown in Figure1.Cut and polished pure copper lump was put into silicone mold and melted epoxy resin was poured into it and cooled, then, finally the binary sample was polished and molded in the form of 10 mm * 10 mm * 10 mm."

Jan 1, 2017

By Richard C. Williams, Herman Pieterse, Ken Thomas, K. S. Fraser, Ron H. Colquhoun

"The Banick Goldstrike Mines Inc. (Goldstrike) operation is located in Eureka County in north-central Nevada on the Carlin geological trend. Gold in the sulphide mill feed, occurs primarily as submicroscopic inclusions or possibly solid solution in a pyrite and marcasite matrix. Sulphide mill feed is pretreated in a pressure oxidation plant allowing gold recoveries of 90 per cent and greater to be achieved. Anticipated 1994 gold production for the sulphide gold facility is approximately 1,500,000 ounces.In January 1989 American Banick Resources Corporation (Banick) announced the US$365 million Betze Development Plan for the Goldstrike property. The Betze plan was based on a three (3) staged expansion of the original 4,500 STPD oxide gold plant. This expansion would involve addition of ore and gold processing capacity and the total conversion of all ore handling facilities to treating Betze sulphide ores.Phase 1 of the Betze Development Plan involved the construction of a pressure oxidation circuit, including a single autoclave and supporting ancillary services. The pressure oxidation circuit was commissioned in February 1990. Currently a throughput of 2,000 STPD is being achieved.Phase II of the Betze Development Plan, commissioned throughout April and May 1992, included the expansion of grinding, leaching, and gold recovery facilities enabling the treatment of combined oxide, and sulphide ore. Pressure oxidation capacity was increased by the addition of two (2) autoclave circuits each treating 2,600 STPD of sulphide ore and other required ancillary services. By June 1992, the Phase II gold facility had achieved a combined throughput of 15,000 STPD of oxide and sulphide ore.Phase Ill, the final stage of the Betze Development Plan, was successfully commissioned in February and March 1993. This final stage of development increased the design throughput of the pressure oxidation plant to 15,000 STPD by the addition of three (3) autoclave circuits with combined capacity of 7,800 STPD."

Jan 1, 1994

By Barry W. Schmitke, J. M. Marino

"Cigar Lake Mining Corporation is presently operating an underground test mine in northern Saskatchewan, with a view to developing a high grade uranium deposit. The mining test is intended to demonstrate that the innovative mining methods designed are safe and economical. Two vertical mining methods are considered for the test:• box hole boring from the lower level;• blind boring from the upper level.In both cases, it is anticipated to freeze the ground before excavation to ensure hole stability and limit the inflow of water. Special care will be taken to minimize radiation exposure of personnel.Remote controlled equipment will be used where applicable.The access to the orebody was an important component of the test. After shaft sinking to a depth of 500 m, development work commenced at the 420 level in fractured sandstone which was grouted to restrict the inflow of formation water. The drifting continued in a section of poorly consolidated sand, clay and sandstone; this area was frozen to allow stabilization prior to excavation. At the 480 level relatively little water was encountered in the altered basement gneiss and grouting was not necessary; however, extensive ground support was required in the soft ground areas."

Jan 1, 1992

By A. H. Winckers

"The Sullivan Mine and Concentrator are owned and operated by Cominco Ltd. and are located in the Rocky Mountain Trench, in Kimberley, British Columbia.The Sullivan Concentrator commenced operation in 1923 at approximately 2,500 tons per day. The concentrator was enlarged in several stages and by 1945 was treating 8,500 tons of ore per day. In 1949, the capacity of the concentrator was expanded to 10,000 tons per day with the completion of the sink and float plant, the installation of the rod mill, an underground crushing plant and a 4-mile underground and surface electric railway from the underground crushing plant to the concentrator. Throughput now averages 7,000 tons per operating day, or 2,400,000 tons per year.The concentrator operates 7 days per week, 24 hours per day while the underground crushing station operates 5 days per week, 24 hours per day. The ore is essentially a replacement deposit in argillaceous quartzite of Precambrian age. The ore bodies are massive deposits consisting of fine grained mixtures of sulphides, sometimes interbanded with the country rock and varying widely in their content of lead, zinc, iron and silicates. The principal economic minerals are galena and marmatite (7 ZnS:FeS). Iron is mainly present as pyrrhotite, and to a much lesser extent as pyrite. The intimate association of these sulphides necessitated the development of a successful differential flotation process before the ore could be beneficiated profitably."

Jan 1, 1981

By Omkar N. S. Beruar

Extraction of sill pillars has always been problematic because of high risk of seismicity and rockburst. Depending on a number of factors, a sill pillar can undergo different failure modes and cause problems in the mine. Of these, sudden and uncontrolled failure of part(s) of the pillar leading to highenergy seismic events and rockbursts is a main concern because it is not possible to predict the location and time of a rockburst apart from its potential to cause extensive damage to the mine structures. To date, a comprehensive technique for sill pillar design and recovery does not exist. Conventional methods of pillar design, such as the pillar stability graph method, are utilized to design stiff sill pillars. In these design approaches, the post-peak response of the pillar-rock system is not considered. This is in part due to a lack of clear and comprehensive understanding of the post-peak behaviour and failure mechanism of sill pillars. In general, the strength of a rockmass is described using a failure criterion. When stresses reach the strength of the rockmass, the rockmass does not necessarily become unstable and knowledge of the loads alone is not enough to assess the instability conditions accurately. In fact, it is not possible to predict instability of rockmass based on the strength/stress ratio alone because instability depends not only on this ratio but also on the loading condition and loading system characteristics. The loading system can dictate whether the sill pillar will go through a stable or unstable failure process. This paper examines the influence of various parameters such as the pillar width to height ratio, the extraction rate, and placement of backfill on the Loading System Stiffness (LSS) and the Pillar Stiffness (PSS). The ultimate goal is to design yielding sill pillars that would yield in a stable manner and will reduce the risk of pillar rockburst. Plane strain finite element analysis is conducted using the generalized Hoek-Brown failure criterion with elastic-brittle-plastic parameters. Examples are given to demonstrate how to calculate these stiffness values and assess the stability condition of sill pillars. It is found that increasing the rate of extraction increases the likelihood of unstable yielding of the pillar as has been found in other studies. Placement of backfill in a timely fashion in the stopes above and below the sill pillars increases the stiffness of the loading system. This indicates that backfilling of stopes while creating the sill pillar increases the likelihood of stable yielding of the sill pillar.

Aug 1, 2013

By Xuanxue Mo, Kaihui Yang, Steven D. Scott

Abstract -The Changning-Menglian metallogenic belt in western Yunnan, China, is characterized by the occurrences of both Pb-Zn-Cu and Cu massive sulfides in Permo-Carboniferous mafic volcanic sequences. These deposits were formed in a back-arc basin at a rifted continental margin in the Paleozoic Tethys Ocean. Pb-Zn-Cu deposits are associated with alkalic basalt, andesite, and lesser felsic volcanic rocks intercalated with limestone, which probably formed along an immature rifting segment on a continental basement. These volcanic rocks are enriched in K, Ti, LREE, and other incompatible elements, and have the attributes of alkalic within-plate basalt. An extensive unit of sulfide- carbonate-silica shale in proximity to massive sulfides contains high values of Mn, As, Mo, W, Sn, Sb, and Hg, and has REE patterns that are similar to the volcanic rocks. This, together with the graded bedding in the footwall volcanic rocks, suggests that the sulfides precipitated in a shallow, unstable, and carbonate-saturated volcanic basin. A stringer zone is traced downward for 500 m below the massive sulfide orebodies. It is characterized by an upper sericite-quartz zone and an extensive lower skarn alteration with enhanced W, Sn, and Bi. Lead isotope data show both continental basement and magmatic sources may have supplied the ore metals. Cu deposit and occurrences are hosted by tholeiitic units that represent the mature spreading segments in the back-arc basin. The tholeiitic lavas have LREE-depleted or flat REE patterns similar to MORB or back-arc mafic lavas. The cupriferous massive sulfides are overlain by an extensive unit of chlorite-magnetite or ochre, suggesting a relatively oxygenated oceanic basin. Ni and less Co mineralization is found in dolomite veins of the stringer zone. Enhanced concentrations of Ni, Co, Au, and As are found in the massive sulfides and in sulfide-rich tuffites. The geological setting and mineralization of the Changning-Menglian belt has similarities with modern back-arc basins such as the Manus Basin in the western Pacific.

Jan 1, 1999