Search Documents

By F. Q. Barnes

"Uranium, thorium and yttrium have been recovered, since the 1950s, from pyritic quartz-pebble conglomerates occurring in the basal sediments of the Quirke syncline at Elliot Lake. Gold, an element of interest in similar type deposits occurring worldwide, is a very minor constituent of the Elliot Lake conglomerates because the provenance area of the sediments had few gold-bearing rocks.Uranium, thorium and rare elements are found in resistate and diagenetic minerals occurring in the matrix of the conglomerates. The valuable elements are recovered from the acid soluble minerals during the milling process.Large uranium reserves occur in mines found on both limbs of the Quirke syncline. Major reserves are being developed on the South Limb of the syncline, where the Stanleigh Mine, among four past-producers, has been reactivated.IntroductionUranium and thorium commonly occur in anomalous amounts in coarse basal sediments. Radioactivity in basal conglomeratic sediments is generally attributable to resistate minerals, that rarely occur in concentrations high enough to be of economic significance. One type of basal conglomerate found worldwide, in Precambrian cratonic basins, has uranium or uranium and gold concentrations large enough to be of economic interest. Principal among the occurrences are the pyritic quartz-pebble conglomerates of the Huronian in Canada, of the Witwatersrand in South Africa and at Jacobina in Brazil.The uranium and gold mineralization of these conglomerates was derived from provenance areas where both elements occurred and were later concentrated through source degradation and deposition in placers in a reducing environment. Only the Huronian conglomerates, generally much richer in uranium but with negligible gold, have been exploited solely for their uranium content.The uraniferous conglomerates of the Huronian at Elliot Lake, 500 km north of Toronto, continue to represent a major world source and supply of uranium concentrate."

Jan 1, 1986

By Jamal Asfahani

Abstract - Natural gamma ray well logging, an effective tool in geophysical prospecting, is used to investigate the radioactive and phosphatic layers in the Khneifiss mine in Syria. The interpretation of the gamma ray measurements, using numerical methods of analysis developed previously and applied successfully in some phosphatic areas in Syria, make it possible to define precisely the phosphate thickness from place to place in the study area. This technique has been successfully applied while studying seven boreholes in the area. Sixty-three core samples from phosphatic layers in the boreholes have been analyzed, using gamma ray spectrometry for the determination of P2O5 , U, Th, and K. Good correlation between P2O5 content and U concentration has been found. The total count gamma logs correlate reasonably well with the U core analysis, suggesting that radioactive equilibrium exists in the U decay series. These gamma logs can be therefore used effectively to quantitatively map the distribution of P2O5 and U. The characteristics of both subsurface phosphatic sand and phosphatic rocks have been investigated and outlined using a statistical approach. The affinity of uranium to some trace elements such as V, Sr, Cu, and Ni has been verified using correlation matrices of these elements.

Jan 1, 2002

By Al Goodier

"This paper discusses the experience of Noranda Mines Limited, Matagami Division, with the vertical crater retreat (VCR) method in the mining of narrow-vein stopes. Although limited to only one stope, the viability of this method at the Radiore No.2 Mine has proven that further use of VCR in narrow-vein mining will be made.IntroductionThe Radiore No.2 property is located east of the Bell River in the southeast quadrant of Isle-Dieu Township, approximately 4.5 km east of the town of Matagami. The new James Bay Highway is 2.5 km north of the property and access to the mine is by a 2.5-km logging road.The property was staked by Radiore Uranium Mines in March 1961 and the sulphide body was first indicated by an E.M. survey. Diamond drilling commenced in the fall of 1961 and was completed by the end of 1962. As per an agreement in 1970, the claims were sold and assigned to Orchan Mines Limited. Subsequently, the property was transferred to Bell Allard Mines Limited, a wholly owned subsidiary of Orchan Mines. Early in 1979, Noranda Mines Limited acquired the property and it is now part of Noranda's Matagami Division.Geology and MineralizationThe deposit is in a band of volcanic rocks north of the Bell River complex. The lens of massive sulphides dips almost vertically and strikes almost east-west. The north contact is essentially sharp against andesite material; the south contact is less well defined, as the massive sulphides tend to grade into more disseminated material.The orebody varies from 5 to 20 feet in width, by 350 feet long and 200 feet in height. The overburden is composed of sand, gravel and clay, varying from 0 to 26 feet in depth. The ore reserves were 153,340 tons grading 1.97% copper and 1.01% zinc including 10% of dilution at zero grade."

Jan 1, 1982

By D. Newman

"This paper discusses the author’s work on international law norms of consultation with Indigenous communities and examines unexpected corporate stakeholder impacts on these norms. Customary international law, which governs the area, does not traditionally refer to corporate conduct. This paper surveys several sources on developing international law on consultation obligations; it also discusses the impacts these norms can have on corporate stakeholders in the mining industry. Finally, it asks how interactions of corporate stakeholders in this area can indirectly impact future law and suggests implications for different business models in the mining sector.RÉSUMÉ Le présent article traite du travail de l’auteur sur les normes de consultation avec les communautés autochtones contenues dans le droit international et examine les impacts inattendus des parties prenantes sur ces normes. Le droit coutumier international, qui gouverne ce domaine, ne réfère traditionnellement pas à la conduite des sociétés. L’article analyse plusieurs sources traitant du développement de nouvelles lois internationales sur l’obligation de consulter; il traite aussi des impacts que ces normes peuvent avoir sur les parties prenantes dans l’industrie minière. Finalement, il pose la question à savoir comment les interactions des parties prenantes dans ce domaine peuvent avoir un impact indirect sur les lois futures et il suggère des implications pour divers modèles d’affaires dans le secteur minier."

Jan 1, 2015

By S. Markstrom

The Boliden AITIK copper mine is located 100 kilometres north of the Arctic Circle in northern Sweden. A pre-feasibility study was conducted in 2005 with the aim of increasing the capacity of the existing processing plant. After analysis, options to upgrade the existing plant were abandoned in favour of building a new processing plant, with higher capacity and therefore greater profitability. A new plant could be designed with greater flexibility to make potential future expansions easier. A feasibility study for a new 36 Mt/y processing plant including fully AG grinding circuits and flotation was completed in 2006. The project was approved by the Boliden board shortly thereafter. Construction started in the beginning of 2007 and was completed during 2009. Commissioning of the new plant was undertaken in the first half of 2010. The grinding circuit consists of two lines with each line consisting of a 22.5 MW AG mill and a 10 MW Pebble mill in closed circuit with a spiral classifier. The nominal production level is 2 200 t/h for each grinding line. This paper presents the start-up and operation of the grinding circuit.

Jan 1, 2012

By A. J. Williams, W. H. A. Timm

"Lake Dufault Mines, Limited, is located north of Noranda, Quebec, and is a producer of copper and zinc concentrates. Various papers have been given on the mill design, construction and operation. 1, 2This paper is intended to describe the application of computer control to the Lake Dufault milling process. A brief history and description of the plant flowsheet will be given, followed by the reasons for installing the computer and the development of the program up to its present use. The success attained to date, comments on economic justification and future plans will also be given.HISTORY AND FLOWSHEETThe Lake Dufault ore body was discovered in September, 1961, and the mill commenced production during August, 1964. The rated capacity of 1,300 tons per day was reached by October 1, 1964. In milling the Lake Dufault ore, many metallurgical problems have been encountered, mainly due to wide and rapid variations in mill heads and oxidation of the massive sulphide ore. However, flexibility in plant layout and the incorporation of up-to-date instrumentation have facilitated its processing."

Jan 1, 1969

By B. Loveday, G. W. Delaney, S. Cummins

"Applying DEM to prediction of tumbling mill performance is challenging because several different modes of breakage are active in the process. As our knowledge of breakage and computational capacity improve, it is worth revisiting previous simulation tasks which did not produce a satisfactorily realistic description of a measured process. At SAG 2006, we reported the simulated and measured outcomes of treating a well characterised ore in a 1.2 m diameter mill. This well instrumented, pilot scale mill at the University of KwaZulu-Natal has been combined with some new approaches to ore testing to allow different modes of breakage to be tested. The mill design allows the rate of generation of fine material to be measured in close to real time for autogenous and SAG mill charges. The updated simulation model estimates mass loss with particle evolution and embeds the cumulative damage and breakage.The simulated results are compared with the measured results. Issues such as relating modelling inputs to particle breakage characterisation data and the accuracy of the predictions of the models are discussed."

Jan 1, 2012

By Trung Nguyen

Midwest is a unique uranium deposit with exceptionally high arsenic content. The ore body is located 17km west of the McClean Lake operation. The McClean Lake mill will be modified to process Midwest ore and handle solid wastes coming from the Midwest water treatment plant. This paper describes the modifications required of the McClean Lake mill, process challenges associated with treatment of the arsenic, and the possibility of recovering nickel and cobalt as a by-product. It also reviews the complexity in the design of the Midwest water treatment facility which incorporates reverse osmosis technology with conventional physical-chemical water treatment.

Aug 1, 2010

By D. Crone, T. Watts

"The Lindsley project was a program of deep drilling to test the contact down-dip from two nickel-copper deposits, one uneconomical and the other mined out. The role of Borehole Pulse EM(PEM) was to detect the higher grade, more massive sulphide zones if they were missed by a drillhole, and to help determine geometry if the zones were intersected. Two problems appeared as the PEM survey progressed: (1) conductivity-thickness as measured by the PEM did not always relate to economic sulphides as determined by the market; (2) a pattern of unusual PEM anomalies was obtained that indicated something odd and big, but the cause was unknown. A large fold structure subsequently was indicated by a program of deepening previous holes, the third of which intersected high-grade mineralization below 1280 m. Falconbridge is in the process of shaft sinking and underground exploration.IntroductionThe Falconbridge Lindsley property is on the south rim of the Sudbury basin, 8 Ian north of downtown Sudbury. The original property was acquired by a prospector named James Stobie, who, in early August 1885, staked a showing that later became the Mount Nickel mine (Fig. I). On August 10 Stobie staked another property that would become the Little Stobie mine, and at the end of the same month he staked the main Stobie orebody.In 1888, the ground immediately west of the MOlU1t Nickel find was staked. This ground contained the Blezard deposit (Fig. 1) which was put into production in 1889 and was eventually acquired by Inco. Down-dip from the Blezard workings, on Falconbridge ground, is located the upper Lindsley No. 1 deposit which was drilled off by Falconbridge in the 1940s to 1950s. A decision to go underground on the Lindsley No.1 mineralization was made in 1969, but the project was cancelled in 1971 because of declining nickel prices. The shaft was stopped at 95 m, and the headframe and hoist were sold. Further surface exploration drilling in the 1970s discovered the deeper Lindsley No. 2 zone, but as it had grades similar to those of the No. 1 zone, it too was considered uneconomic."

Jan 1, 1992

By W. Beres, Li. J.

The finite element method (FEM) has been applied to investigate the stress fields and deformation of a TiN/Ti-6A1-4V coating/substrate system subjected to nanoindentation. MSC Patran and MSC Marc were used to prepare the three-dimensional finite element models and to perform the simulations of the Vickers nanoindentation experiments. Pure silicon and TiN/Ti-6A1-4V coating/substrate system were analyzed. The properties of the materials were assumed to be homogeneous and isotropic with a linear hardening behavior. The reverse method was used to extract material properties, such as the yield stress and strain hardening coefficient, from the numerical results by comparing the simulated indentation load vs. penetration depth (P-h) curves with those obtained experimentally. Both non-linear elastic and non-linear elastic-plastic analyses were carried out for the coating/substrate system. The results are given for four different coating thicknesses.

Jan 1, 2004

By R. S. Forgan

The synthesis and study of a systematic series of phenolic oximes have shown that substitution in the 3-position can greatly affect extractive efficacy. Solid state, solution and gas phase analytical techniques, including X-ray crystallography, EPR and IR spectroscopy and collision induced dissociation mass spectrometry have been assessed for their applicability in interpreting the origins of differences in extractant strength. The dominant substituent effect on pH0.5 is the change in ligand pKa, with the more acidic ligands being stronger extractants. The influence of the 3-substituent on the stabilising intracomplex H-bonding of their copper(II) complexes also affects extractant strength. The 3-NO2 substituted ligand shows the lowest pH0.5 value, due to a combination of its low pKa and a stabilising bifurcated H-bond assembly around the copper(II) centre. Appending an aminomethyl group to the 3-position gives a ligand capable of binding a metal and its attendant anion. These metal salt reagents show potential to open up new flowsheets for the processing of high tenor copper feeds.

Jan 1, 2007

By Richard Dawson

Presentation Outline? Northeast BC Coal Fields Overview and History ?New mines and projects in development ?Design Issues for steeply dipping footwall slopes ?Design issues for angle-of-repose waste rock dumps

May 1, 2006

By Chantale Doucet

L?utilisation du remblai en pâte dans les exploitations en vrac est de plus en plus importante. Puisque la technologie existe pour fabriquer du remblai en pâte sans construire une usine coûteuse, il est maintenant possible d?élargir le domaine d?utilisation du remblai en pâte pour y inclure des gisements filoniens où le besoin annuel de remblai est moindre. Dans certains cas, l?utilisation du remblai en pâte pourrait permettre de réaliser d?importantes économies telles que la réduction de la dilution, la stabilité des ouvertures, la récupération d?une plus grande partie du minerai par la réduction de la taille des piliers et l?entreposage de moins de résidus à la surface. L?ampleur des économies est parfois difficile à chiffrer mais il est tout de même important d?en tenir compte lors de la décision d?utiliser du remblai en pâte puisque ce sont souvent ces économies qui seront déterminantes. Différentes méthodes d?extraction avec remblai en pâte appliquées aux mines filoniennes seront présentées. Des défis et les solutions reliés à l?utilisation du remblai en pâte à la Mine Doyon seront discutés.

Oct 1, 2001

By Marcel Vallée

"This text consists of two parts, comments on "Classification and Reporting of Mineral Resources for High-Nugget Effect Gold Vein Deposits," by S.C. Dominy, P.R. Stephenson and A.E. Annels, Volume 10, No. 3, pp. 215-233, and related comments on some features of the JORC Code.This paper is, in many respects, a very elaborate and valuable account of the problems encountered in the estimation and classification of high-nugget gold deposits. However, in some key areas, it appears to fall short of its objective to help "resolve satisfactorily most issues" and "contribute to improved estimation and classification" (abstract). One must realize that high-nugget effect gold deposits constitute a very narrow field, despite the occasional bonanzas. This is a field of mostly smaller sized deposits, where limited success and a significantly higher rate of failure occur relative to larger deposits of mostly lower grade. This is shown by the six deposits described in the paper. Thanks for contributing to greater understanding of these complex and nevertheless challenging deposits."

Jan 1, 2002

By C. A. Born

This paper describes the rejuvenation of a molybdenum mine mill complex at the head of Alice Arm, 500 miles north of Vancouver and 85 miles north of Prince Rupert, British Columbia. It includes a description of the property history of the deposits and of the previous operations, together with details of the project for re-opening the mine.

Jan 1, 1979

By Stephen Esposito

Outline ? Brief Overview of Solid Energy New Zealand ? Need for Integrated Risk Management at Solid Energy New Zealand ? Overview of Solid Energy?s IRM program ? What are the results and key learnings? Overview Of Solid Energy New Zealand ? 100% NZ Government Owned ? Produces 95% of New Zealand?s Coal ? Sales turnover USD150 million per year ? Sold 4 million tonnes of high quality coal in 2003 ? Coking and Thermal coals ? Exported 2 million tonnes of coal ? Significant international and domestic growth expected going forward

May 1, 2004

By R. F. Tylecote

"The closure of the iron and steel making plant at Consett in Durham in 1980 marked the end of an era-a long era in the world's iron and steel making history. Iron had been smelted in the Tyne-Wear area of the United Kingdom since before the Roman period, but apart from evidence of smithing in the Roman period, the historical evidence for iron production on a large scale dates from the 14th century.The paper describes sites in the area that first worked the bloomery process and then, in the 16th century, as did most of Europe, graduated to the blast furnace process. The main emphasis is on the early introduction of coal to iron making at the end of the 18th century and the use of the steam engine to render integrated sites possible.IntroductionIron has been smelted in the Tyne-Wear area of the United Kingdom since before the Roman period, but apart from clear evidence of smithing in the Roman period, the historical evidence for iron production on a large scale dates from the 14th century. Like many other countries, the United Kingdom benefitted from the visits of foreign observers, such as Jars, Svedenstierna, de la Houliere and Dufrenoy, who left detailed records. In modern times, information gained from excavations of iron and steel making sites has supplemented the historical record.Natural ResourcesUp to the end of the 19th century, the industry was wholly dependent on its own resources. Iron ore, limestone, wood, coal and water power were all found a short distance away from the main valleys of the Tyne and Wear. The main sources of iron ore were the coal measures, with rider ores from the lead vein s in Alston and Weardale, and carbonate ores from shale horizons in the Carboniferous limestone. Good coking coal was available from West Durham and reasonable coal from the Tyne valley and Northumberland limestone. Limestone was plentiful."

Jan 1, 1983

By Jacek Paraszczak

L?exploitation rentable des gisements de type filonien constitue un problème important dans le contexte actuel de l?industrie minière québécoise. Les études effectuées depuis 1994 ont indiqué, que la technologie d?abattage mécanique utilisant l?outil hydraulique appelé « éclateur radial-axial » constitue une alternative intéressante par rapport aux méthodes conventionnelles par le forage et sautage. Les essais du prototype de l?éclateur ont prouvé qu?il est en mesure d?abattre les roches dures dans un environnement minier, mais sa performance dans les termes de masse du roc abattu dans une unité de temps a soulevé certaines doutes. Pour cette raison, une étude de préfaisabilité de l?éclatage en tant qu?une technologie d?excavation souterraine a été réalisée. Cet article présente quelques résultats des travaux effectués dans le cadre du contrat octroyé à l?Université Laval par le Ministère des ressources naturelles du Québec. Leur objectif principal consistait à comparer, pour les conditions des gisements filoniens, la productivité et les coûts des méthodes d?exploitation souterraine utilisant l?éclatage par rapport à celles conventionnelles. Deux variantes proposées de cette méthode ont été comparées avec la méthode conventionnelle sur le plan du coût (par tonne de minerai) et de la teneur de coupure de minerai d'or. Les études ont démontré que l?application de l?éclatage représente un potentiel de réduire ce coût, surtout dans les situations où l?abattage sélectif pourrait avoir lieu. Pour le cas de base on a trouvé, qu?il serait possible de réduire la teneur de coupure par la marge d?environ 16 ? 26%. Toutefois, les études de sensibilité ont démontré, que le coût dépend de façon important de la productivité d?éclatage, qui, pour sa part, varie beaucoup en fonction de paramètres du massif rocheux devant être abattu.

Oct 1, 2001

By Claudia Gasparrini

"Factors affecting the extraction of gold are of a mineralogical nature. Knowledge of the mineralogy of the ore or metallurgical product to be treated, if appropriately combined with the metallurgical test work, may improve gold recoveries. .This paper outlines the mineralogical techniques f or the study of gold ores and metallurgical products and describes the gold mineralogy in relation to its metallurgy. An effective plan for studying refractory and other difficult ores, combining metallurgical test work, chemical analysis and mineralogy and capable of giving positive results over relatively short periods of time, is suggested.IntroductionFactors affecting gold recoveries are of a mineralogical nature and include (i) the gold-bearing minerals, (ii) their grain size and, particularly where the grain size is very fine (10 microns in diameter and less), (iii) their host minerals and (iv) the association these form with the gold-bearing minerals.Mineralogical studies of gold ores and metallurgical products containing gold in economic amounts (today down to 1/10 of one ounce per tonne or 2.84 ppm) are difficult and time consuming. Mostly because of such reason, metallurgical testing (test work) is usually done simply by trial and error without understanding the causes for failure or success.Mineralogical studies, if appropriately conducted and combined with the test work, provide an efficient mean s of improving recoveries through the understanding of gold losses derived from the use of the wrong technique for separation. The information they provide is therefore the first step in the development of recovery techniques, for those ores where the test work alone failed to produce positive results."

Jan 1, 1983

By Jean-Luc Collins

"The paper deals with the impact of fleet imbalance on a deterministic evaluation of shovel fleet productive capacity. It shows that if the fleet imbalance is overlooked, then estimated fleet productive capacity will be overrated.The paper shows that fleet imbalance inflates utilization, and care must be taken when using such statistics which are derived from reported field-equipment-hours. It shows that the utilization must be deflated by a factor called 'balancing efficiency"" in order to estimate shovel productive capacity correctly. The paper also shows how fleet imbalance can be controlled by managing idle time or downtime in an actual operation.The technique used for measuring the balancing efficiency factor is based on statistical analysis of equipment utilization."

Jan 1, 1980