Search Documents

By G. Russo

During the construction of the S.Martin La Porte access adit, 9m in diameter, extreme squeezing conditions occurred while crossing Carboniferous schistose formations, with diametric convergence up to 2m. Back-analysis of monitoring results shows that an acceptable simulation of the observed excavation behaviour can be derived using a combined analytical and numerical approach, with simple elasto-plastic laws but a progressive reduction of residual parameters and a relevant increase of dilatancy.

May 1, 2009

By S. Kelebek

Efficient separation of minerals is the essence of mineral processing. Separation of hexagonal pyrrhotite in processing of Ni-Cu sulphide ores was investigated together with particle size effects with respect to selective flotation recovery of pentlandite and nickel. The recovery by size response was compared for sodium metabisulphite (SMBS), triethylenetetramine (TETA) and their combinations with amyl xanthate as a collector. The pyrrhotite recovery for all sizes was lower than that of pentlandite for the blank case as well as individual cases with SMBS and TETA. For pyrrhotite, the recovery by size relations in the case of individual uses of reagents were mainly determined by recovery losses at coarser size range (>74 um), which occurs at a coarser size for pentlandite (>212 um). The combined use of SMBS and TETA, and the associated synergistic effect very significantly knocked down the pyrrhotite recovery to less than 7% that was a maximum for the –10 um (attributable to hydraulic entrainment). High recovery of pentlandite in a wide range of intermediate sizes and drastically low recovery of pyrrhotite resulted in a very efficient separation of pentlandite from pyrrhotite in all sizes. Separation of this mineral is discussed in relation to fundamental functionality of the reagents used.

Jan 1, 2017

By J. Schmidt

Cold drawing of copper wire rod is usually combined with an in-line annealing process to adjust the ductile microstructure of the wire again. One important key factor for successful annealing is the quality of the copper itself. Rod producers can check the recrystallization behaviour of the rod by different methods: chemical analysis, Spiral Elongation Test (SEN) as well as the Rapid Elongation Test (AR) are some examples of common testing methods. The comparison of the results of these methods does not always show sufficient correlations. The paper introduces firstly the SEN and AR-Tests and their different approaches to the mentioned task. The second step is to compare some results of the SEN-Test with the results of the AR-Test and identify causes of deviations. Thirdly, the effect of pre-annealing is discussed, which is especially common for wire rod with diameters of more than 8 mm.

Jan 1, 2007

By K. G. (Ken) Thomas

"This paper gives an insight into the various processes available to treat gold ores. A brief overview is given of the various types of refractory gold ores. Particular emphasis is given /0 comparing the costs of oxide vs refractory gold ore processes, inclusive of grinding through to dore bar.HistoryThro ugh time gold has been recovered from the earth's crust by various mean s. Five major historical steps can be identified for metallurgical processing as shown in Table I .Gravity concent ration started with, for example, river bed panning and developed to more sophisticated processes such as the Johnson concentrator, belt concentrator and jigs. The South African gold fields were a major developer of gravity concentration processes during the first half of the twentieth century.As coarse free gold became depleted, stamp milling, in conjunction with amalgamat ion , was developed. Basically, rock was crushed under large mechanical hammers an d the gold collected in mercury . The mercury was then evaporated in a retort to leave sponge gold for further fire refining.As deposits became deeper and gold finer, the gold became more difficult to recover ; fine grinding was required to liberate the gold. In the 18905, MacArthur and the Forrest Brothers of Glasgow, Scotland, introduced the cyanide pro cess for dissolution of gold and its subsequent precipitaiton by means of zinc. This process, in vogue until the early 1970s, was commonly referred to as the Merrill-Crowe process for recovering fine gold .Activated charcoal was used as a means of recovering gold from solution in the 1880s, especially in chlorination plants in Australia( l). Two factors probably retarded the development of carbon instead of zinc-based processes during those year s. First , there was no satisfactory procedure for the elution of carbon to allow its recycling and, second, the development of the Merrill-Crewe process for gold recovery by zinc cementation probably discouraged any further work on the use of carbon"

Jan 1, 1991

By Paul D. Young, Michael J. Allan

"The Con Mine has been producing gold continuously since 1938. In 1990 laboratory and pilot plant investigations began into the use of pressure oxidation for treatment of an arsenic trioxide waste product from two previous roaster operations on the property. This led to the construction in 1992 of a 96 ton/day plant to treat a mixture of arsenic waste and flotation concentrate from the existing mill. The plant was commissioned in the fall of 1992.This paper describes experience gained in the commissioning and initial operation of the plant. The unique aspects of treating a hazardous waste product are described including special operating procedures to satisfy environmental and employee safety concerns. The paper further describes modifications made to the process flowsheet, to operating procedures and to materials of construction in the early months of operation."

Jan 1, 1994

By J. Paraszczak

Application of teleoperated and automated (or ?autonomous?) mobile equipment in underground metal mines represents a promising avenue for overcoming some of the challenges facing the industry. This paper addresses the overall effectiveness of autonomous loading and haulage equipment compared with conventional human-operated machines. Factors affecting availability, utilization, and production rate are explored, and an emphasis is placed on some problems and risks not present in conventional human-operated systems, as well as on the character and criticality of autonomous equipment. The need for a more in-depth analysis of factors affecting overall autonomous equipment effectiveness is stressed; these factors should be taken into consideration at the stage of feasibility studies. The paper concludes with recommendations and directions for future research.

Aug 1, 2010

By J. Paraszczak

ABSTRACT: Application of teleoperated and automated (or “autonomous”) mobile equipment in under-ground metal mines represents a promising avenue for overcoming some of the challenges facing the industry. This paper addresses the overall effectiveness of autonomous loading and haulage equipment compared with conventional human-operated machines. Factors affecting availability, utilization, and production rate are explored, and an emphasis is placed on some problems and risks not present in conventional human-operated systems, as well as on the character and criticality of autonomous equipment. The need for a more in-depth analysis of factors affecting overall autonomous equipment effectiveness is stressed; these factors should be taken into consideration at the stage of feasibility studies. The paper concludes with recommendations and directions for future research.

Jan 1, 2010

By C. Feng, D. W. M. Arrigan

Arsenic is often associated with gold mining operations and poses a significant health and environmental hazard. While a number of technologies are available for removing arsenic, none of them is effective under all conditions. Although adsorption is a promising approach, most methods focus on the purification of water under neutral or acidic conditions and tend to be less effective in gold mining process waters, operating under alkaline conditions. In this study, the removal of As (III) and As (V) from both arsenic-only solutions and simulated process waters using composite magnetic nanoparticles was investigated. The nanoparticles consisted of magnetite (Fe3O4) or maghemite (?-Fe2O3) cores covered by various metal oxides with Langmuir adsorption capacities of As (III) and As (V) ranging from 31.4 to 79.1 mg/g and 10.2 to 25.5 mg/g, respectively, in arsenic-only solutions at pH 9. Their adsorption capacities were further recognised by the adsorption tests conducted in simulated process waters. The ability to remove As (III) is of particular importance as it is harder to remove it from alkaline solutions. The magnetic cores allow simple and efficient magnetic recovery of the As-loaded nanoparticles.

Jan 1, 2017

By Otto Engel

"A multipurpose program for a hand-held programmable TJ-59 calculator and PC-100C printer facilitates the evaluation of various mineral processing tests and the calculation of mass and metal balances. Its application is demonstrated by some example problems. Detailed user instructions are given for each application.IntroductionThe program listed in Appendix I is written for a programmable Texas Instruments TI-591 PC-100C calculator I printer combination. The program is applicable for the evaluation of:1) screen analyses;2) flotation test s; and3) mass and metal balances.Each application is demonstrated by an example problem and corresponding detailed user instructions. The ""measured"" data in the examples are fictitious and do not represent a real operation.The steps in using the program are the same for each of the three types of application, viz.:1. Enter the number of product fractions and press ""A"".2. Enter the measured weights (0) of each fraction and press ""RIS"" each time. After the last fraction has been entered, the printer automatical1y displays the total weight.3. Press ""B"" to calculate the weight distribution (Y). Once ""B"" is pressed, the printer automatically displays the weight distribution of all fractions.4. If the accumulated weight distribution (EV) is also needed, press ""RIS"". The printer now displays these data. This step is optional and may be bypassed.5. Press ""2nd A"" to prepare for entering of the measured metal assay (M).6. Enter the measured metal assays of each fraction and press ""RIS"" each time. If analytical data exist for more than one metal, each data set has to be entered separately in one sequence.7. Press ""C"" to determine the ""calculated"" head assay (MA) of all fractions.8. Press ""RIS"" to calculate the metal distribution (R). Once ""RI S"" is pressed, the printer automatically displays the metal distribution of all fractions. This operation is optinal and may be bypassed if desired.9. Again press ""RIS"" to obtain the accumulated metal distribution (ER). This operation is optional and may be bypassed.10. Press ""D"" to calculate the gangue distribution in the concentrate (W). One ""D"" is pressed, the printer automatically displays the data for all fractions. This operation is optional and may be bypassed.11. Press ""RIS"" to obtain the accumulated gangue distribution (EW). This operation is optional and ma y be bypassed.12. For more than one metal, press ""E"" to clear the memory for storing the assays of the next. Then press ""2nd A"" and start entering the assays of the next metal as described previously (6 to 11). Steps 5 to 12 may be repeated as many times as desired."

Jan 1, 1982

By A. Hasselbring

Sub-Level stoping was used in this country at least as early as 1912, at the Magpie mine in Michipicoten. The fundamental principles of the system are the same wherever it is used, but modifications have been adopted in the Michigan iron mines and in several Canadian mines. It is a system whereby a suitable body of ore may be developed quickly and worked cheaply, with a low initial expense, and by miners of quite ordinary ability. The basic method, described in the following pages, may be modified to meet conditions where one or more factors are not in accord with normal sub-level stoping requirements. In suitable ground, sub-level stoping is probably the most satisfactory method yet devised for underground hard-rock mining. It is so simple, straightforward, and safe that no special training of a crew is necessary. Any miner capable of drifting and raising can carry on the work necessary for sub-level stoping after the shaft has been sunk. The method is suitable, however, only for reasonably wide ore-bodies, the minimum width of ore to which it can be economically applied being somewhere in the neighbour-hood of thirty feet. The development programme is simple. Assuming, for purposes of illuslustration, an ideal ore-body, two thousand feet long, dipping nearly vertical, and varying in width from forty to a hundred feet, this programme would be as follows. The shaft should be sunk on the footwall side about sixty feet outside of the ore-body and near its centre. Levels are then established at suitable intervals, usually 125 feet. On each level, a cross-cut is run to the ore-body, and there a main-haulage drift is driven in either direction to the end of the ore. Cross-cuts are then run at 25-foot intervals, so that ore-chutes can be spaced about 25 feet centre to centre each way. It is not necessary that these cross-cuts be extended to the walls of the ore-body, if the position of the walls is known; they are extended just far enough to make room for the correct location of the chutes.

Jan 1, 1934

By Garry Biles, Ken Major, Raj Anand

"Prime Resources Group Inc. (Prime) commenced the Eskay Creek Mine operations in 1994 in northern British Columbia. The ore from the underground mine is crushed and shipped to smelters in Japan and Canada. The nominal production rate is 300 tonnes per day.Before commencing the above operations, preliminary evaluations for the high grade gold mine had indicated that an extremely complex metallurgical and chemical process flowsheet would be required to recover the economic metals. Subsequent to the metallurgical testing program, Prime identified markets for the untreated ore and initiated underground mining and ore transportation operations.Prime recently identified lower grade ore zones, which are less economic or uneconomic to mine and ship directly to the smelters. Test programs were initiated to evaluate processes for upgrading the ore to a marketable product. In 1997, Prime will complete the engineering and construction of a 150 tonne per day flotation plant to concentrate the gold and silver values for the NEX and 109 zones. The mine will then, in addition to the direct shipping of the shippable ore, ship concentrate from the millable ore. This paper discusses the development and design of the flotation plant.IntroductionThe Eskay Creek Mine is located in north-western British Columbia approximately 83 km north-west of Stewart, B.C. as shown in the location map Figure 1. Access to the site is provided by a restricted access gravel road from Bob Quinn Lake junction of highway 37, a distance of about 59 km. The work force at the mine is based on a two-week rotation schedule. Employees are flown from as far away as Vancouver to Smithers by commercial airlines and then from Smithers to the Bob Quinn airstrip by local charter. During poor weather conditions, transportation to site is by vans that take about six hours to travel the 450 km road distance."

Jan 1, 1998

By G. C. Weatherly, D. S. Wilkinson, A. M. Limarga

In addition to the harsh environment, materials for high-temperature applications are often subjected to a significant mechanical loading. Several researchers have noted that the rate of oxidation can be affected by stress in a range of materials. We have recently studied this effect in y-TiAl, based on the preliminary work of Magnan and Weatherly which showed that nitridation rates on the tensile side of a flexural creep specimen could be 10 times higher than on the compressive side. We have since developed a four-point bending creep setup capable of controlled atmosphere testing. We present quantitative data on the effect of creep on scale growth under a range of atmospheric conditions. Finite element analysis will also be used to show how modest applied stresses can have a large effect on scale growth rates through the generation of large stresses due to the mismatch of creep rate between the metallic substrate and the scale.

Jan 1, 2004

By M. Xiao Bo

In recent years, there has been a heightened interest in the hydrometallurgical processing of sulfide ores and concentrates (especially copper sulfide ores and concentrates) mostly in the USA and Chile. Currently, hydrometallurgical operations account for about 30% of the primary copper production. In the present research, the leaching phenomena of IOCG (iron-oxide hosted copper-gold) ores and concentrates were studied. The IOCG ore, which is characterized as having a predominant amount of magnetite with fine chalcopyrite, is currently the center of attention for new copper resources. Heap leaching of IOCG ore is desirable because of its low cost. However, the leaching characteristics of the ores and concentrates and the mechanisms of copper leaching require investigation. This study defines the factors, which affect the leaching operation, such as the ORP, pH and oxidizing agents. Based on these results, the optimal leaching conditions are provided for pilot column leaching test and ultimately, commercial operations.

Jan 1, 2007

By M. Gruber-Pretzler

Technical Sn- bronzes tend to form both macrosegregations and microsegrega¬tions during DC-casting due to the particular thermodynamic properties and kinetics of phase transformation. As a result a heterogeneous cast microstructure forms that is some¬times a reason for a decrease in workability. The extent of macrosegregations in DC-casting can effectively be influenced by casting parameters like casting velocity, primary cooling or inlet geometry which in fact change the relative flow between the melt and the forming solid. In order to understand the influence and interaction of the related phenom¬ena, simulation methods are applied. The solidification of the strand as well as the forma¬tion of macrosegregation are simulated with a two phase volume averaging model. The velocity field of the melt flow is explicitly calculated by solving the corresponding mo¬mentum conservation equations. Within the mushy zone the local formation of microseg¬regations in the presence of feeding flow is estimated. The thermodynamics of the Cu-Sn system is accounted for and it is distinguished explicitly between interface and average concentrations. To investigate the influence of feeding flow on the formation of mac-rosegregations, a study has been performed. Based on this result, the phenomena of mac¬rosegregations are described in a detailed discussion.

Jan 1, 2007

By Jessica Hurst, Mark Holdsworth, Jeff McKay

"In 2002, Kennecott Utah Copper Copperton Concentrator installed an Expert Control system for optimization of their SAG and Ball milling circuits. The advanced process control has been well received and is utilized well over 95% of the time. In the years since, many lessons have been learned and many advances have been made. Improvements have produced millions of dollars of benefits and have included directly controlling feedrate with complex logic as opposed to using a bearing pressure controller, modifications to how sound is used for control, modifying logic for maximizing asset utilization and using advanced control for automating equipment restart. INTRODUCTIONRio Tinto’s Kennecott Copperton Concentrator produces copper, molybdenum, gold and silver. The mill has 4 SAG mills (SAG 1-3, 34 foot diameter and SAG 4 36 foot diameter), 8 ball mills and copper and molybdenum flotation plants, as seen in Figure 1. The 2010 average data is shown in Table 1.In 2002, a Metso Cisa OCS Expert Control system was installed at Copperton for SAG and Ball mill advanced control. The expert control was first placed on SAG 2; data from the first few weeks compared with operator performance indicated approximately an 11 percent increase in throughput. After full commissioning, the system was gradually refined further by plant personnel to develop key performance indices based on SAG feed size, refinement of the sound setpoint for control of mill speed and throughput, specific rules to help the adjustment of speed based on loss of a feeder, etc. With the addition of the pebble crushing circuit, the expert control began utilizing a model estimation of crushed pebble bin level to help stabilize the impact of returned crushed and uncrushed pebbles on the SAG mills. As the ore and limitations change, it is necessary to evolve the SAG logic to better handle any constraints."

Jan 1, 2012

By Rodrigo A. Marinho

Erratic high grade values are as common in Nature as they are a source of problems for resource estimators. In some highly erratic metal deposits, less than 2% of the drilling samples can represent more than 10% of the total metal in the blocks and they are associated with a high risk level. There is a risk of local overestimation but also of global overestimation, with the high grades being projected over too large a volume. Capping or restriction of these outliers control is being widely used in the industry and commonly applied in resource estimation for the last three decades. The primary purpose of this paper is to present and describe the most applied methodologies for restricting the extrapolation of high grade samples and discuss the results based on a theoretical simulated model. Additionally, this paper demonstrates the economical impact associated with the high-grade and the project risk profile associated with each method.

Oct 1, 2009

By John A. Meech, Irene E. Cristoveanu

"The separation of hematite fines (100% - 38 um) from quartz fines (100% -75 um) was investigated using coarse hematite (-212 + 150 um) as a carrier in an oleic acid collector system. Oleic acid additions, per cent coarse additions, combined conditioning time and ferric chloride additions were examined.It was found that carrier flotation is a dominant mechanism for fine hematite recovery at oleic acid levels greater than 200 g/t and coarse additions of 10 per cent. Hetero-aggregation is favoured under conditions of lower levels of oleic acid in the presence of ferric chloride and at conditioning times greater than ten minutes.Ferric chloride acts as a depressant for pre-reagentized coarse hematite at oleic acid levels below 150 g/t. At concentration levels above 500 g/t, ferric chloride interferes significantly with the success of carrier flotation of fine hematite.The sensitivity of carrier flotation to changes in oleic acid addition, ratios of fine and coarse material, conditioning time and the presence of an inorganic electrolyte emphasizes that its application is only suitable when flotation conditions can be stabilized.IntroductionThe production of fine material is unavoidable during the comminution of iron ore . Due to the difficulty of recovering iron from this fine material by various gravity separation methods, flotation can often be a more attractive process producing high-grade material at high recovery. One variation of the flotation process, that can be useful for recovering ultra fine minerals (<10 um) , is known as carrier flotation. This process involves the utilizat ion of coarse particles ( > 150 p.m) which act as flocculation centres to which the fine hematite particles (10 - 40 u.m) become attached and are carried or "" piggy-backed"" into the froth phase."

Jan 1, 1985

By M. P. Rennick, D. M. Burton

The Murray Brook massive sulfide deposit, which was the first geochemical discovery in the Bathurst camp, is one of the largest sulfide deposits in the area. The massive sulfides are hosted by quartzose metasedimentary rocks in the lower part of the Ordovician Tetagouche Group. This thick succession of sedimentary rocks is overlain conformably by felsic volcanic rocks, and is structurally overlain by mafic volcanic rocks. The massive-sulfide body is polydeformed, but primary metal zoning is still discernable and may permit future exploitation of discrete lead-zinc and copper zones. Although it was discovered in 1956, the deposit was not developed until 1989, when Murray Brook Resources commenced processing of gossan containing precious metals. Recovery of gold, silver, and mercury is accomplished by indoor vat leaching on a year-round basis.

Jan 1, 1992

By Bob Rappolt

Discussion Points Part 1: Global Mining Industry/Related Issues ? Historical Metal Price Trends. ? Historical LME Metal Stockpiles. ? China?s Demand for Metal. ? World Population Growth, Demands and Development. Discussion Points (cont?d) Part 2: Canadian Mining Industry ? Where are we? And where are we going? ? What progress have we made in the past 20 years regarding: ? Safety -Employee Levels ? Labour -Relative Compensation ? Productivity - Technological Advance ? Where do we stand regarding mineral production? ? What does the future hold for us?

Apr 1, 2005

By R. J. Chase, C. Davies

"The Merelani graphite-tanzanite deposit is located in northeast Tanzania, 14 kilometers south of Kilimajaro International Airport and in close proximity to the towns of Moshi and Arusha. The graphite mineralization is hosted by relatively undeformed linear Proterozoic metasedimentary gneisses, several of which have been subjected to hydrothermal alteration resulting in tanzanite mineralization. Exploration work comprised detailed geological mapping coupled with pit and trench channel sampling and a subsequent 1500 meters of diamond drilling. In addition, metallurgical tests have shown the graphite to be of unusually coarse flake size, crystallinity and high purity.Feasability studies have shown the economic viability of a major coarse flake graphite deposit with the measured resource to 50 meters in excess of 9 million tonnes assaying over 85 graphitic carbon. Production is due to start by the end of the first quarter of 1994 with the processing plant design capacity initially set at 15 000 tonnes per annum.In addition to graphite production, tanzanite will be produced through selective mining within the graphite open pit in the upper horizon and from underground workings within the lower horizon.The Merelani graphite-tanzanite deposit will be the first major orebody to be exploited through means of private funding since Tanzania gained independence"

Jan 1, 1994