Search Documents

By W. J. Mcgaughey, R. G. McCreary, S. C. Maxwell, R. P. Young

"Seismic tomography is a process for obtaining images or maps of seismic velocity or other seismic properties of a rock mass. Seismic velocity images reveal variation in elastic moduli which, in tum, are related to several properties required in the geological or geomechanical assessment of a rock mass. Seismic velocity is sensitive to lithology, discontinuities, and in situ stress. Spatial or temporal variation of these properties may be indirectly assessed. Tomographic measurements are sensitive to volumes of ground, rather than determinations at points, or along lines or surfaces, as in conventional geological or geomechanical measurements or mappings.Tomography surveys are complementary to conventional measurements as they have the capability to interrogate a substantially larger volume of ground. They are thus useful in discerning trends or patterns in regions between or surrounding conventional ""point"" measurements of lithology, rock quality, stress, or other parameters of interest. Seismic velocity images give broad indications of trends in velocity; their spatial resolution of ground properties is typically on the order of five to ten per cent of the nominal survey dimension.Research in seismic tomography has been carried out for several years, and the capabilities and limitations of the technique in mining environments are beginning to be understood. This report reviews the present capabilities of seismic tomography surveys in mining, emphasizing rock mechanics applications. Six case studies are used as examples to demonstrate the capabilities of the method in assessing lithological variation, density and orientation of discontinuities, and the effects of stress."

Jan 1, 1994

By K. Fujita, T. Kikuchi, Y. Sakamoto

Ceramic fibers were classified as a category 2 carcinogen by The European U legislation. Therefore we developed non-fibrous insulating castable which utilizes n porous aggregate, which is composed of Calciumhexaluminate. Although at beginning we applied alumina cement as binder for non-fibrous insulating castable, kind of formulation had a poor resistance to spalling. We developed non-fibrous insulating castable without alumina cement. This solved a problem which pre\ formulation had a poor resistance of spalling. We applied a new non-fibrous insub castable for reheat furnace in steelworks, then we could achieve good result which condition equivalent to ceramic fiber insulating castable.

Jan 1, 2004

By G. E. Agar

"The distribution of gold in the grinding-classification circuit of an operating gold plant was determined by assaying the size fractions of samples from each of the streams. This analysis identified the streams with the maximum potential for gravity recovery of gold and revealed that there was up 110 seventy-five times as much gold in the primary cyclone underflow as in the concentrator feed.Laboratory jigging and tabling tests were done on samples from two of the streams to determine what the recovery might be with a gravity circuit and to show that a high grade concentrate could be produced. A numerical simulation procedure was used to calculate a material balance for a circuit that included gravity separation on the primary cyclone underflow. The numerical simulation optimistically indicated that as much as 84% of the gold might be recovered in a reasonable grade of concentrate even though the recovery in batch bench scale tests was only 14%.Incorporation of a gravity separation device would reduce the inventory of gold in the grinding-classification circuit.INTRODUCTIONMany gold concentrating plants include a gravity concentration operation while others do not and the reasons that some do and some do not is not clear. Some of the advantages and disadvantages of gravity circuits are discussed by Penman (Penman 1987) without clear cut resolution. Penman's comments elicited an interesting response from Lloyd (1989) who produced a simple way to determine if the addition of a gravity concentration circuit would enhance the recovery of gold. Lloyd's method does not consider the cost of running the circuit so it only partially answers the question. There are reports in the literature (Wells and Patel 1991, Matwijenko 1988) that as much as 60% of the entire production comes from a gravity circuit when it is used, and that the grade of the concentrate produced often exceeds 65% gold, an assay that far exceeds most Merrill-Crowe precipitates that are sent to refining. In at least one instance (Hood 1984) a range of recovery from 40-50% was indicated from laboratory test work and the plant subsequently realized recoveries in the range of 26-40%. Despite these favorable numbers other plants use gravity separation when as little as 20% of the gold is recovered in the gravity concentrate (Carter 1992)."

Jan 1, 1993

By G. E. Wood

THE INSTABILITY of copper prices and their low levels since late 1974 are of great concern to both producers and, to a lesser degree, consumers of copper. The price levels portrayed by the "neutral long-term" price trend are assumed to have been enough to encourage sufficient investment to provide adequate world production capacity and yet not so high as to encourage development of excessive over capacity. The identification of the present level of this trend has taken on special importance for governments and for corporations active in the world copper industry. One approach to the possible determination of such a price is through the use of moving averages. In this way, the effects of relatively short-term price movements can be dampened, as can those related to business cycles. From such averaged price data, long-term trends can be sought over a selected time period. The choice of the past time period for which a price trend is sought may have a major effect on the result'. For example, in the period 1885-1973, the long-term price trend for copper in constant dollars showed a decline, whereas in the period 1919-1973 it was rising. For the purposes of discussion, an appropriate choice of period might be a relatively short and recent one so that the majority of the present cost factors would be present throughout. It should also be long enough to cover a number of full business cycles.

Jan 1, 1977

By D. Runnels, A. Allaire, J. Torrealba-Vargas

Data mining and modelling of operational data involves the discovery of patterns in large datasets for future use in benchmarking and plant optimization. The modern pattern of discovery in large data sets involves statistical techniques, machine learning and new visualization tools. Former examples of data mining are revisited and presented in this document. INTRODUCTION A network of enthusiastic and active professionals is currently developing and maintaining several open source statistical software tools (packages) for data analysis (example Rstudio, Orange, Spyder, etc.). The advantages of the open source software philosophy are the fast development and testing of the solutions presented to the community. Books and support are available for each software application. Since each modern work activity generates massive amounts of data, it is attractive to learn and test those available tools considering that we are at the door of the new work revolution coined as “Mine 4.0”. Data mining involves collecting large datasets, the preparation and cleaning of a dataset (term named data wrangling), the uploading of the data to a database program capable of handling big datasets, the development of prediction models and the presentation of the results. Machine learning techniques help to develop mathematical models and algorithms that could be used to improve the performance on a specific task. Mine operations are producing an incredible amount of data each day and the need to analyze those results seems to be impossible due to the lack of time, as well as the lack of skills to investigate the data collected. If we add to this the traditional habit of working in silos, an additional challenge is to consolidate databases from different departments in search of trends that could help to optimize production.

Jan 1, 2019

By J. N. Cram

"The comments given are to help allay generally accepted ideas that the handling of arsenic as arsenic-trioxide (As2o3J in and from off gas pyrometallurgical operation fumes is difficult, hazardous and expensive. It need not be any of these things if the basic and rather unique chemic3l and physical properties are understood and taken care and advantage of through present day technologies. These particular characteristics are:-(1) As2o3 sublimes and re-condenses, at a relatively low temperature;(2) As2o3 is, for practical in-plant purposes, insoluble in water at ambient temperatures and quite soluble in water just below the boiling point;(3) residual suspended and dissolved As 2o3 can be removed from water by complete dissolution with very little sulfuric acid, followed by the addition of small amounts of ferrous sulfate and calcium chlorate, with oxidation to the ferric and arsenite state and precipitation of an insoluble ferric calcium arsenate, thereby lowering the As2o3 content of solutions to acceptable levels. Even lower levels of non-toxic forms of arsenic solids and residual As2o3 in the water solutions can be attained by also using phosphate, and lime, along with the above.A background re past arsenic processing methods, present day operations, plus predictions re future trends, and hazards, are outlined."

Jan 1, 1979

By R. A. D. Pattrick, D. A. Polya, D. J. Marsh, J. -J. Bao

"Abstract-The utility of high-density stream sediment and stream water sampling to the exploration for silver deposits was investigated by the study of the epithermal Ag-Au base-metal prospect at Lagalochan in western Scotland. The geology of Lagalochan is dominated by a calc-alkaline Caledonian intrusive complex emplaced into Dalradian Supergroup rocks (Harris et al., 1988a). The complex consists of subvolcanic porphyrytic rocks associated with intense hydrothermal alteration and brecciation. Early Cu-Ag-Mo-rich mineralization is found in the core of the complex with later Pb-Zn-Ag-Au-As-Sb-rich mineralization toward the margins (op. cit.).Stream sediment sample analysis spatially resolved the Cu-rich and Ag-rich mineralization. Ag and Cu anomalies relative to local background values were found in all size fractions analyzed (-125 µm, +125 µm, +180 µm, +250 µm) but the more pronounced anomalies were found in the -125 µm fraction. The coarser fractions generally revealed more erratic but longer dispersion trails. The separation of Cu-rich and Ag-rich mineralization is also apparent in the distribution of relatively high dissolved Cu and Ag in stream waters, particular when expressed relative to the solute load as Cu/TDS and Ag/TDS.The mineralization at Lagalochan is indicated by Ag, Cu and Pb stream sediment and water concentrations that are anomalous with respect to local backgrounds, but are difficult to distinguish from regional backgrounds. This emphasizes the further potential of high-density stream water sampling, in particular, as a viable geochemical exploration tool on a sub-regional scale for epithermal deposits in relatively unpolluted upland terranes."

Jan 1, 1995

By Barbara H. Scott Smith

"During the last two decades lamproites have joined kimberlites as the only two known primary sources of economic quantities of diamonds. This paper contrasts the petrography, primary and xenocrystic mineralogy and pipe geology of these petrogenetically separate rock types. The petrographic discrimination of kimberlites and lamproites from each other, as well as other rock types found during diamond prospecting, is discussed. Kimberlites and lamproites can be classified texturally and mineralogically. Such classifications highlight the differences between, and among, lamproites and kimberlites. The implications of these differences for diamond exploration programs are discussed, with particular emphasis on the application of petrography. IntroductionKimberlite was the term coined in the late 19th century to describe the host rock of diamond at the type locality, Kimberley, South Africa (Lewis, 1887, 1888). Innumerable kimberlites are now known worldwide; some of them contain economic quantities of diamond (e.g. South Africa, Botswana and Russia) while many are barren. Jennings (1989) suggests that less than 3% of the known kimberlites can be considered to be commercial. Kimberlite was thought to be the only important primary source of diamond for approximately a century. Until the late 1970s, lamproites were thought to be only academic curiosities. Some workers (e.g. Wade and Prider, 1940), however, did comment on certain similarities between lamproites and kimberlites and, hence, inferred a potential for lamproites to carry diamonds.The term lamproite was introduced by Niggli (1923) for leucite-bearing rocks from southeast Spain and Wyoming which had some unusual geochemical characteristics. Wade and Prider (1940) used the term lamproite (as defined by Troger, 1935) to embrace rock types found in the West Kimberley area of Western Australia. All the lamproites described by Wade and Prider (1940) form distinct topographic features. Subsequently in the late 1970s, additional pipes, which have little or no relief, were discovered in the same area, but only as the result of a major diamond exploration program (Atkinson et al., 1984; Jaques et al., 1984, 1986). Some of these bodies are diamondiferous. In 1979, the Argyle pipe was discovered in the East Kimberley area which, in terms of grade, is the richest known primary diamond deposit in the world with some parts of the body having grades greater than 500 carats/100 tonnes (Madigan, 1983; Boxer et al., 1989). All the initial new discoveries in Western Australia resulted from classic stream sampling for ""kimberlite indicator minerals"" (Atkinson, 1989)."

Jan 1, 1992

By R. Tomás, J. B. Serón, M. Romana

The Slope Mass Rating (SMR; Romana, 1985) geomechanics classification was developed as a sequel of Bieniawski’s Rock Mass Rating (RMR) system, which was almost impossible to use in slopes due to the extreme range of the correction factors (up to 60 points of a maximum of 100) and to the lack of definition of them. A detailed quantitative definition of the correction factors is one of the advantages of SMR classification. During the last thirty years the use of SMR system has been extended to many countries from the five continents and, thus, it is time to review the most interesting developments. Both RMR and SMR are discrete classifications, depending on the values adopted by the variables that control the parameters. This can cause major changes in the parameters value due to small differences in the variables value, with changes in the final rock mass assigned quality. On the other hand, geomechanics quality indexes are extremely biased. To avoid this problem, some authors have proposed continuous functions for SMR. This classification has been also adapted for its application in heterogeneous and anisotropic rock masses, for high slopes, for is application trough stereographic projection and Geographical Information Systems, has been used as susceptibility rockfall parameters and has been included in the technical regulations of several countries. Additionally, some open access computer tools have been developed for the computation of SMR. Consequently, this paper reviews: 1) the most important modifications and adaptations of slope classifications which derive directly from SMR; 2) the use of SMR throughout the world; 3) many significant papers on slopes analysed with SMR all over the world; and 4) future trends in the use of SMR.

Jan 1, 2015

By S. Parada, P. T. Jones, M. Guo, S. Smets, E. Boydens

The corrosion behaviour of a pitch-bonded MgO-C refractory in contact with a vacuum oxygen decarburisation slag with high Al2O3 content (12-17 wt%) is investigated under VOD process conditions by rotating finger tests in a vacuum induction furnace. The refractory degradation mechanisms are studied by the characterisation of the corroded microstructures using scanning electron microscopy, equipped with energy dispersive spectroscopy. The influence on the refractory wear of the process temperature, corrosion time and the Al2O3 content in the slag is discussed. The degradation mechanisms include slag infiltration, direct MgO dissolution from the refractories into the penetrated slag, erosion of magnesia grains at elevated temperatures, removal of carbon through the MgO-C reaction, and finally, oxidation of refractory carbon by reducible slag components. Both a porous MgO layer and a dense (Mg)(A1,Cr)2O4 spinel at the slag/brick interface were observed. Their formation mechanisms and industrial relevance are discussed.

Jan 1, 2004

By D. Harris, S. Murugesan, G. Ye, G. Oprea, J. Rigby, T. Troczynski

The spinel-added and in-situ spinel bonded castables have been developed and widely used in steel industry. It is challenging to develop magnesia-based castables for the non-ferrous industry because the temperatures in industrial furnaces are significantly lower than those in the steel industry and therefore the binding systems of these castables must have the capability to develop a ceramic matrix below 1300°C. It is also challenging to develop a good binding system without addition of fume silica, because the hydration of magnesia may take place during installation, curing and firing of the castables. This work presents the experimental results on developing magnesia-based cement-free, silica fume-free refractory castables using hydratable alumina as the hydraulic binder and a spinel phase as the final ceramic binder. In order to activate the sintering and have a ceramic matrix well developed at the relatively low required temperatures, ultrafine aluminas, chromia, magnesium-aluminate spinel and aluminum titanate powders were used as components of the binding system.

Jan 1, 2004

By C. H. Ash

"The Red Chris Cu-Au deposit (522.7 Mt at 0.35% Cu and 0.27 g/t Au), northwestern British Columbia, is one of several pre-accretionary porphyry systems in the Cordillera of westernCanada. It is hosted by an Early Jurassic hornblende monzonite to quartz monzodiorite porphyry which forms part of a suite of dikes and stocks that intrude Late Triassic volcanic strata. Major and trace element chemical data suggest that these Early Jurassic intrusions have compositions which fall on the boundary between alkalic and calc-alkalic compositions. Alteration and mineralization in the Red Chris deposit are more typical of calc-alkaline porphyry systems with abundant potassic, sericitic and argillic assemblages and quartz-rich stockworks. It lacks Na- and Ca-bearing silicate assemblages which characterize the alkalic porphyry deposits of British Columbia. One of the more unusual features of the deposit is the abundance of carbonate alteration and veins which occur throughout the hydrothermal history of the deposit. This type of alteration and veining is more typical of alkalic porphyry deposits.The composition of the carbonates vary both temporally and spatially with different alteration zones. Potassic zones, which are characterized by orthoclase±albite±quartz±chalcopyrite±bor-nite±magnetite±hematite and Au/Cu ratios of 1:1 (g/t Au:% Cu), contain minor siderite veins and alteration. Quartz-sericite-carbonate (QSC) zones overprint earlier potassic alteration and comprisequartz+ankerite+sericite+pyrite+chalcopyrite with Au/Cu ratios of 0.5:1 (g/t Au:% Cu). Ankerite isthe main carbonate in this stage but has a variable composition with a more Fe-rich variety associated with mineralized veins. Localized chlorite-carbonate alteration zones, characterized by chlorite+carbonate+quartz±kaolinite±pyrite±gypsum and high Au/Cu ratios [2 to 3.5:1; (g/t Au:% Cu)],contain predominantly calcite. Late stage carbonate-gypsum veins have an ankerite to dolomite com-position which is very similar to the regional carbonate alteration and veins."

Jan 1, 1997

By Xuehui Xia

Abstract -There are a number of sedimentary exhalative massive sulfide (SEDEX) deposits in the Proterozoic Langshan-Zhaertai rift at the western segment of the northern margin of the North China platform in China, including more than ten large, medium and small deposits located in a belt of 300 km EW by 50 km to 100 km NS, with large Cu, Pb, Zn, Ag, and S reserves. In several representative SEDEX deposits in the rift, the mineralizing elements are prominently zoned, horizontally or vertically, with Cu decreasing but Pb increasing from west to east, Cu decreasing but Zn increasing from bottom to top, and Zn restricted to the bottom half. The ore-hosting rocks, characterized by a clear manganese halo, have developed a polymetallic mineralization in positive relation with their carbon contents. Their isotopic aspects are: ?34S has relatively large positive values, fluctuating between +5‰ and +35‰, compared with Pb isotopic compositions which are less variable, with a model age of 1600 Ma to 1800 Ma, showing that they are mantle-derived. The mineralizing materials were associated undoubtedly with the contemporaneously faulting events in the rift. The deposits owe their origin to seafloor exhalation, with sedimentary rocks as their hosts.

Jan 1, 1999

By Fathi Habashi

Extraction by organic solvents is a chemical process in which metal species in the aqueous phase react with an organic reagent to form an organometallic com- plex, thus, the metal species leave the aqueous phase and enter the organic phase from which it can be stripped back in the aqueous phase to obtain a pure and a concentrated solution. The metal in the organic phase is not bound to carbon atoms as in organometallic compounds but to oxygen, nitrogen, sulphur, or hydrogen by a co-ordination (dative) bond (Habashi, 1999).Solvent extraction was used for the first time in hydrometallurgy in connec- tion with the special and urgent materials requirements of nuclear energy during World War II. A plant was constructed in the United States for the preparation of high-purity uranyl nitrate solution. In this plant, the yellow cake (a high-grade sodium or ammonium uranate) was dis- solved in HNO,, and uranium was selec- tively extracted by ether then stripped by water to give a concentrated solution of pure uranyl nitrate. This was gradually followed by developing methods for other high-priced metals such as plutonium, thorium, niobium, tantalum, zirconium, hafnium, boron, beryllium, and molybde num. The second step took place in the 1960s when solvent extraction was applied for the first time to extract a rela- tively cheap metal-copper. At present, solvent extraction technology is wide- spread, well accepted, and highly efficient. Solvent extraction had its origin in the discovery, by Christian Friedrich Bucholz (1770-1818) in 1805, that uranyl

Sep 1, 1999

By Masami Nakamoto

Controlled thermolysis of gold(I) thiolate complex, [C14H29(CH3)3N][Au(SC12H25)2], at 180 °C for 5 h under an N2 atmosphere produces novel gold nanoparticles passivated by alkyl groups derived from the precursor complex, the TEM photograph of which shows spherical particles with average diameter 26 nm. Since Brust et al. reported the two-phase reduction of AuCl4 - by NaBH4 to afford monodispersed gold nanoparticles passivated by alkanethiolate ligands (1), plenty of preparative investigations on gold nanoparticles (2,3) and its surface modification (3,4) have appeared, because of their potential applications in microelectronics (5). However, those preparative methods generally involve the reduction of AuCl4 - by reducing agent NaBH4 in the presence of suitable organic stabilizers such as alkanethiol (1-4), phosphane (5), quarternary ammonium salts (6), surfactants (7) or polymers (8). On the other hand, O?Brien et al. recently reported the preparation of organically capped gold nanoparticles at 190 °C, where tri-n-octylphosphine oxide and/or n-octadecylamine are used both as a reaction medium and as a passivating ligand (6), but this procedure also needs NaBH4 as reducing agent. Our strategy of novel preparative method of gold nanoparticles is the combination of reductive elimination of thiolate ligands and simultaneous attachment of organic moiety on the growing nuclei. Gold(I) thiolate complexes with ammonium cations were useful for our preparative method. We now report the controlled thermolysis of gold(I) thiolate complexes, [R(CH3)3N][Au(SC12H25)2] and [R(CH3)3N][Au(SC6H4-p-R?)2] (R= C14H29, C12H25; R?= C8H17, CH3), under an N2 atmosphere, where the powder of gold(I) thiolate complexes completely melts to afford the precursor liquid and then the liquid gradually decomposes. In spite of no use of reducing agent and solvent, reduction reaction is thermochemically induced to afford novel gold nanoparticles passivated by alkyl groups rather than by alkanethiolate ligands. Figure 1a shows a typical transmission electron microscopy (TEM) image of gold nanoparticles prepared by thermolysis of [C14H29(CH3)3N][Au(SC12H25)2] at 180 °C for 5 h, indicating a controlled growth of spherical gold nanoparticles. As shown in Fig. 1b, these spherical gold nanoparticles display the size distribution ranging from 5 to 50 nm. Although the particle size is larger than that of thiol-derivatized gold nanoparticles (less than 5 nm) prepared by NaBH4 reduction (1-3), the aggregation of gold nuclei is smoothly regulated and the growth of core gold is limited to be 26 nm in average diameter in spite of thermal procedure.

Oct 1, 2003

By Richard Howie

Avian Diversity ?? Pre-mining ?? 110 - 125 species would have occurred ?? Dominated by forest species ?? Wetland productivity unknown ?? Post mining ?? 192 documented ?? Forested species in reduced numbers ?? Increase in wetland species ?? Increase in open country/grassland species

May 1, 2008

By Esa Peuraniemi, Hanna-Leena Heikkilä

Boliden Harjavalta has been operating a copper flash smelter since 1949. Thus, in 2019, the smelter is celebrating its 70th anniversary of flash smelting. Slag formation is an integral part of the smelting process; currently the processing of slag is based on froth flotation at the slag concentrator. It provides high recovery of copper but restricts slag utilization; the final copper slag is deposited in a landfill. The Harjavalta smelter commissioned a new landfill area for final slag in May 2018. This paper describes the full project from permitting to commissioning of a new landfill area. The permitting process is described comprehensively, including environmental impact assessment together with the environmental and dam safety monitoring. During the environmental impact assessment, observations on rare animals protected on European level were made as well as archaeological findings. Successful completion of the permitting allowed the construction phase to start on time. After six years of intensive work, the new landfill was commissioned in May 2018. The new landfill area provides a sustainable way to store the smelter’s slag for decades to come. INTRODUCTION Slag processing Sulphide based concentrates have always formed the main raw material stream at Harjavalta’s copper smelter. During the smelting and converting steps, the iron included in the concentrate is oxidized and fluxed using a silica-based sand. Originally, the slag was processed by using an electric slag cleaning furnace after which the final slag was water granulated. Froth flotation has been utilized for slag treatment since 1966. In the beginning, the slag was cooled in open ditches. In 1984, controlled slow cooling of slag was licenced to enhance copper recovery at the flotation plant. Today, the slag from both the smelting and converting is tapped/skimmed to slag ladles and treated in the following steps: Slag ladle transportation from the smelter to the cooling area by slag hauler Slow cooling of slag in the ladle to allow mineral precipitation Unloading the slag by tilting the ladle; causing the slag to crush as it drops from the ladle Feeding the crushed slag (-500 mm) by wheel loader to a slag concentrator’s feed funnel followed by a conveyor belt transporting the slag to the concentrator plant Crushing and grinding using lump and pebble mills Froth flotation of the valuables Recycling the slag concentrate back to the smelter feed after dewatering Pumping the final copper slag to the landfill area.

Jan 1, 2019

By R. G. McDonald

"High iron solution concentrations often result in the formation of basic ferric sulfate during the high temperature oxidation of sulfidic materials such as base metal and refractory gold concentrates. Consequently, the “Hot Cure Process” followed by limestone neutralization is required to facilitate subsequent processing and/or disposal of the leach residue. The present paper discusses strategies that can be employed to influence the composition and nature of the high-iron content leach residues produced during pressure leaching.INTRODUCTION Control of iron deportment in hydrometallurgical processing remains a key challenge for a range of reasons. Strategies generally relate to the control of conditions under which iron is optimally rejected (Demopoulos, 2009). Supersaturation provides the driving force for crystallization and this can be controlled by a number of factors that include (1) pH and/or Eh control, (2) the presence of matrix anions and impurities, (3) dilution, (4) complexation and dissociation and (5) manipulation of the rate at which the metal to be precipitated is released to solution. Each of these factors is impacted by temperature. Good control of crystallization is essential to the control of precipitate properties such as the degree of crystallinity, stability, particle size and quality which covers both the extent of impurity uptake and suitability of the precipitate for waste disposal. The quality and properties of iron precipitates in turn can impact downstream processing. It is the aim of this paper to discuss the generation of iron-containing residues produced during the pressure oxidation of sulfidic ores and concentrates and how the nature of these can be controlled to potentially facilitate further processing. A brief overview of several related topics will now be given and include, where relevant, discussion of work undertaken in our laboratories. In addition, brief discussions of selected process options that enable good control of iron rejection will be provided."

Jan 1, 2016

By EJ. Reichhardf

The Molopo Farms Complex is a major, layered ultramafic/mafic, early Proterowic intrusion which is totally covered by sediments of the Karoo and Kalahari Fonnations and situated in southern Botswana and northeastern South Africa. The approximately 3000 m thick, generally fine- to medium-grained ultramafic and mafic cumulates are intrusive into equivalents of Thmsvaal Supergroup sediments and lavas. Multiphase defonnation resulted in tilting and segmentation of the Complex into individual tectonic blocks. Sr isotopes document at least two chemically distinct parental liquids which interacted in a complex manner to form an approximately 1000 m thick rhythmically layered succession which straddles the ultramafic/mafic boundary. Repeated mixing resulted in a complex cryptic layering pattern and numerous sulfide-enriched layers which contain significant PGE+Au concentrations.

Jan 1, 1994

By Lawrence Devon Smith

"The concept of risk is well established in the mining industry. It is acknowledged when estimates of reserves are expressed as proven or probable, when mining and metallurgical recoveries are applied to the ore, and when contingencies are added to costs. However, it is difficult to provide a quantitative assessment of risk. The significant sources of risk in a mineral project and how these are addressed in project evaluations are discussed.The discount rate is examined as a fundamental means of reflecting risk in discounted cash flow evaluations. Current industry practice is discussed, and a methodology for the analysis of risk levels is proposed that assesses the constituent components of the discount rate: real interest, mineral project risks, and country risk.IntroductionThis paper examines the components of the discounted cash flow discount rate and proposes a method of estimating project-specific discount rates. The motivation for this work comes from experience of project evaluations in which owners and purchasers had agreed on virtually every aspect of the evaluation except how much the project was worth. Agreement was reached on reserves, grade, recovery, capital costs, operating costs, taxes, and, by combining these components, even on the final cash flow values. The only difference in opinion concerned the discount rate to be used in the calculation of the net present value. Depending on the life of the project, such differences of opinion can cause a variation of more than 50% in the value placed on a project! This is illustrated in Figure I."

Jan 1, 1995