Search Documents

By A. R. Trusiak, C. Bazin, D. Hodouin

"The On-Stream Analyzer has proven, and is still proving to be, an extremely valuable tool for the control of flotation circuits. This paper examines the possibility of going further in the utilization of the analyzer results by using a real-time material balance program to calculate the mass flow rates within the streams of a circuit for process control, analysis and optimization as well as for the detection of sensor malfunction. The material balance algorithm improves measurements and give good estimates of unmeasured variables during normal operating conditions. The potential and limitations of the method are illustrated using results of an application to the Line 3 flotation circuit of Brunswick Mining and Smelting, New Brunswick.IntroductionThe On-Stream Analyzer (OSA) has gained, over the last two decades, the status of key instrument for the control of flotation plants. The OSA is currently used in almost every sulphide flotation plant and its application in oxide mineral flotation plants isincreasing. Commercial OSAs include a sampling system that collectssamples from various streams of a circuit and exposes thesamples to an X-ray beam. The sample then generates X-ray pulsesthat are converted into assays using multilinear regression programs(Leroux and Franklin, 1994). The estimated assays arepassed to the flotation operators via operator consoles, or to controlloops of various degrees of complexity (McKee, 1991), whichmanipulate reagent addition, aeration rate or froth thickness toensure an adequate operation of the plant. Although this applicationrapidly pays for the purchase of the OSA, one should ask:""Could we get more from the OSA?"""

Jan 1, 1995

By K. Shitogiden, Y. Samada, T. Miki

Steelmaking slag contains nutrition such as Si, P and Fe for acceleration of phytoplankton growth. Phytoplankton can fixate carbon dioxide more than any other species on earth. Hence, suppression of CO2 can be achieved by applying the potential of steelmaking slag as the nutrition for their propagation. When it is considered to supply nutrition from steelmaking slag to seawater, we must avoid dissolution of hazardous elements or change of pH of seawater by steelmaking slag addition into seawater. The protection against dissolution of fluorine into artificial seawater has been studied based on dissolution behavior of steelmaking slag and synthesized substances into artificial seawater in the present work. The dissolution mechanism of fluorine from steelmaking slag and buffering action of pH change are discussed by using stability diagram in seawater.

Jan 1, 2004

Accountability for profit realized or lost, and responsibility for continued safe operation are the main impetus behind operator training. Efficiency in operation enables production at lower unit costs. An inefficient operation eats profitability of the operation, creating short term losses, and also affecting longer term viability particularly when commodity prices fluctuate and competition erodes market share. Safe operation and efficient operation are ultimately conjoined entities which may not be able to be sustained without dual effort. Training is a very valuable tool to engage operations in adopting more efficient and safe practices. Training requires time, facilities and trainers. One novel way of minimizing both the trainers and the facilities is through the use of Computer Based systems. Included amongst this are Computer based equipment simulators, following an identical philosophy as flight simulators used for pilot orientation and training for different aircraft types.

Feb 1, 2008

By Fernando Canales

In the last decade a great dealt of attention has been paid to the chemistry of polynuclear gold derivatives with a central heteroatom, not only from the experimental and structural but also from the theoretical standpoint (1). Interesting hypercoordinated species of the type [C(AuPR3)5]+, [C(AuPR3)6]2+, [N(AuPR3)5]2+, [P(AuPR3)5]2+ and [P(AuPR3)6]3+ have been described (2), apart from other complexes with more conventional stoichiometry, and all have in common the presence of gold-gold interactions of ca. 3 Å. Usually, the chemistry of the first row elements of the p-block is known to follow classical rules of bonding, and only in cases of extreme electron-deficiency has the traditional electron count to be reconsidered to account for special types of molecular or solid state structures. Many of these heteroatomcentered complexes are electron-deficient and the gold-gold interactions provide a significant contribution to their stability. The attraction between these closed-shell systems has recently captured the attention in inorganic and organometallic chemistry (1). P. Pyykkö has summarized the available theoretical and experimental evidence of intra- and inter-molecular interactions between heavy metal atoms, such as Au(I) (3). In general, when heavy metals are involved in such interaction, the closed-shell attractions are of metallophilic or van der Waals type, as has been found for d8, d10 coinage-metals, and d10s2 centers. Experimental evidence for the aurophilic Au(I)???Au(I) attraction is available from crystallography, NMR and Raman spectroscopies, and optical spectroscopic measurements of the interaction strength (4). It is manifested in molecular conformations with relatively close Au???Au interactions of ca. 3 Å, whose strength has been estimated at ca. 25-50 kJ/mol (5). These attractions are weaker than most covalent or ionic bonds, but stronger than other van der Waals bonds and comparable in strength to typical hydrogen bonds. The phenomenon cannot be satisfactorily explained by classical theories such as hybridization (3). From a theoretical point of view, the attractions close to equilibrium distances are caused by dispersive interactions together with relativistic effects (6). The attractive contributions are dominated by pair-excitations from the heavy metal, such as gold, strengthened by relativistic effects. In all the cases where there are inter- or intramolecular metal-metal attractions, the correlation effects are essential; if they are omitted, at the Hartree-Fock (HF) level, repulsive interactions are obtained (6). Hence, it is necessary to use at least second-order Møller-Plesset level (MP2) methods for the dispersive forces, which are included in the electronic correlation effects (7).

Oct 1, 2003

By G. Grant Smith

In situ bulk density of coal is a variable applied to various aspects of coal resource evaluation, such as compositing ply analyses of coal attributes that are expressed on a weight per cent basis, and determining tonnages from volume estimates. Its value is a function of composition and porosity of the in situ material. When densities of ash-free coal, ash and water are fixed, in situ bulk density of a coaly mix can be expressed as a function of proportionate weight of ash in the mix. Correlations between in situ bulk densities and weight per cent ash contents of coaly mixes have been estimated for four general rank classes of coal (low medium volatile bituminous, high volatile bituminous, subbituminous, and lignitic).

Jan 1, 1991

By Z. Mubarok

An overview of the problems encountered the electrorefining of copper anodes containing high levels of nickel and antimony is presented. Our investigations have been focusing on the passivation behaviour of the anodes with high contents of Ni, Sb, Sn, and Pb, the formations of kupferglimmer and floating slimes. The results of linear voltammetry, chronopotentiometry and electrolysis test revealed a noticeable lower resistance of the anodes to passivation in comparison to those with lower contents of Ni, Sb, Sn, and Pb. Anode containing kupferglimmer exhibited oxygen gas evolution during the passivation state. Scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) indicated that tin can replace and/or join antimony in the kupferglimmer structure. Under specified experimental conditions, floating slimes precipitations took place with high Ni, Sb, Sn, and Pb anodes prior to the end of one anode period.

Jan 1, 2007

By Lionel C. Kilburn

"This geological engineering method is based on jour main characteristics of mineral properties, viz; location: inclusion of valuable mineralization; inclusion of geophysical and/or geochemical targets; and inclusion of geological targets. These are subdivided into a total of 19 subcategories, which are used to determine the value of the property.The nineteen subcategories are prioritized and assigned relative value factors from 1.3 to 10. Value of each mineral claim unit is determined by applying the appropriate subcategory factors to a base value of $400per 16.2 hectare unit. Property value is calculated by totalling the values of such individual claim-units.The boundary between ore grade and sub-ore grade must be estimated for each property under valuation, thereby making the method sensitive to mineral commodity prices.A clear and disciplined sequence of decisions based on personal experience forms the basis of this method. The method utilizes all factors normally used to value a mineral property.IntroductionIt is generally accepted in the exploration industry that valuation of exploration properties is a subjective rather than objective process (Roscoe, 1986; Lawrence, 1988; Lawrence, 1989; Woodcock, 1985), and that it is greatly influenced by the experience and qualifications of the person who is doing the valuation. However, the significantly low degree of objectivity in mineral property valuation at this point in time invites effort to achieve a more quantitative engineering basis.Value of a mineral property depends basically upon metal prices, recoverable grades, mining and metallurgical practices, commodity supply and demand , and political-economic conditions, all of which vary with time. Therefore, any valuation is valid for only that point in time when it is made. Mineral deposits can decrease as well as increase in technical value with time."

Jan 1, 1990

By Andrew Bamber

The mining and beneficiation of minerals is the second largest end-use of electrical power on the planet, and comminution is by far the largest single contributor to this. Several jurisdictions, including British Columbia, have, in response to concerns about greenhouse gas emissions and climate change, adopted energy conservation legislation, including carbon taxes, carbon trading and conservation incentive schemes. Key to achieving conservation objectives is firstly an understanding of usage metrics across the various unit operations in the sector, and secondly an understanding of the conservation potential represented by available technologies and approaches in reducing end-use. This paper presents the results of a recent utility-funded study on energy use metrics and conservation potential at large open pit mines which are typical of the sector in BC.

Aug 1, 2013

By A. Chaisantikulwat

Most solid-oxide fuel cell (SOFC) modeling emphasizes steady state cell operation. However, understanding the dynamic behavior is essential to predict the performance and limitations of SOFC power systems. In this work, we demonstrate a dynamic model of a SOFC, and we simulate a feedback control scheme that can maintain output voltage despite load changes. Dynamic response is determined as the solution of coupled partial differential equations derived from conservation laws for energy, mass and electric charge. From such a model, the step responses to system input variables can be determined. Low order dynamic models that are sufficient for feedback control design can be derived from the step responses. The development of the partial differential equation model is outlined, and the limitations of the control system are discussed.

Jan 1, 2005

By Charles Tkaczuk

Key issues ? No business tool has greater potential to effect change and enhance profitability than process control. ? Successful businesses see process control as an integrated engineered system, designed and built into their business models from day one. ? The integration and use of process control sets the stage for years of compounded returns. ? Has been used for years to optimizing recoveries and minimizing waste. ? However, the mining/ore extraction sector has been slow to adopt integrated process control. What is the problem? ? Most executives and engineers do not clearly understand process control when applied to mining/extraction activities. ? Common approach has been to apply generic process control strategies as a blanket cure all and wait for it to pay off. ? No central focus which results in multiple group involvement, overlap and inconsistent application of questionable technology. ? Considered a low priority until production activities commence. ? Comfort in using brute force mining methods. ? An off-the-shelf integrated under ground mining process control architecture has not until recently been available.

May 1, 2004

By William D. Gallant, Thomas M. Barczak, Carol Tasillo

"This paper describes the results of full-scale testing of several multi-layered wood crib configurations that were tested in the Bureau of Mines mine roof simulator in cooperation with the Cape Breton Coal Research Laboratory and Cape Breton Development Corporation of Sydney, Nova Scotia. Nine different crib configurations currently being used as wood packwall supports for advancing longwall applications in Canada were evaluated. Configuration parameters understudy included the aspect ratio (height-to-width relationship) and percentage of solid material used in the crib construction. Test results and generalized wood crib behaviour are discussed in detail. Recommendations are made concerning crib constructions to maximize strength and stability. A cost benefit analysis of multi-layered wood crib configurations is made. A comparison of laboratory results and underground observations of several wood packwall supports in the Sydney coalfield suggest in situ load capacity is less than that measured in laboratory testing. Reasons for the apparent decrease of in situ load bearing capability are described.IntroductionA cooperative effort was undertaken by the U.S. Bureau of Mines with the Cape Breton Development Corporation (CBDC) and the Cape Breton Coal Research Laboratory (CBCRL) to evaluate the behaviour of gateside packing materials used in advancing longwall mining applications in the Sydney coalfield. As part of this effort, full-scale tests were conducted on wood packwall supports in the Bureau's 3-million pound (13.3 MN) active load frame.Nine different pack configurations were evaluated as part of this study. The wood packwall supports were multi-layered crib constructions from 6 in. (0.15 m) by 6 in. (0.15 m) cross section timbers using timber s 30 in. (0.75 m) and 60 in. (1.5 m) in length . The percentage of solid material in the crib constructions varied as illustrated in Figures 1 and 2. A summary of crib constructions is provided in Table 1."

Jan 1, 1991

By R. Maxwell

"At Opemiska Copper Mines we have, over the past four years, operated 300 cu. ft. and 700 cu. ft. flotation cells as roughers, scavengers and cleaners and found them competitive with conventional flotation cells on a cu. ft. basis on all phases of flotation.The economics are very much in favour of the large cells for the following reasons:Power consumption is 35 to 40%, of conventional machinesMaintenance cost is about 20 to 25% of conventional machinesSpace required is about 30 to 35% of conventional machinesInstallect cost is about 40%, of conventional machinesTo put the above in more concrete terms below is what we are doing at Opemiska:1. Increasing mill capacity from 2000 to 3000 T.P.D. and will use only 5Cff, of the flotation space for 3000 tons that we used for 2000 T.P.D. with conventional flotation machines.2. Will require only 10 flotation cells for 3000 tons against 85 conventional cells for 2000 tons.3. Cells will be, one 2000 cu. ft. rougher, six 700 cu. ft. scavengers (2 banks of 3 each) and one cleaning circuit using three 300 cu. ft. cells.You will note that in this 3000 ton per day plant, we are going to have only ten cells. Had we put in conventional cells for this tonnage, we would have needed 120 cells."

Jan 1, 1970

By M. Sabau

The Electrowinning Plant at INCO's Copper Cliff Nickel Refinery is a precious metals upgrading plant. The feed to the plant contains copper, nickel, cobalt, iron, significant amounts of precious metals and some impurities. Copper is the most abundant element in the feed. This paper describes the major equipment and process changes over the last twenty years, geared to improve the tankhouse operation, workroom environment and recovery of copper from the acidic solution. Copper is plated on to titanium blanks using explosion-bonded crossrods, animal glue as a levelling agent, and an organic surfactant for mist control. The installation of the stripping machine in 2001 required a number of changes: cathode and anode contacts were redesigned, flat bus bars were replaced with dog-bone type, spacer boards for cathodes and anodes were installed, longer anodes started to be used, and the plating cycle was extended from seven to fourteen days. A number of initiatives for improvement are being carried out. Explosion-bonded crossrods are being replaced with titanium-clad crossrods. The plan for the near future is to increase copper production by increasing current efficiency and current density. The possibility of lowering the iron concentration in electrolyte and changing the acid mist control method is being investigated.

Jan 1, 2007

By Neri Roux, Ross Gilders, Yemi Oyediran, Leo Cheung

Quest Rare Minerals Ltd. is developing their Strange Lake B Zone REE deposit located in Northern Quebec. An extensive batch bench scale testing program was launched to investigate open circuit rougher flotation performance under different conditions. The objective of the flotation study was to demonstrate the effectiveness of rejecting gangue minerals to flotation tailings while concentrating rare earth elements as well as yttrium, zirconium, and niobium into a concentrate suitable for further hydrometallurgical processing. Mineralization of interest at Strange Lake occurs within peralkaline granite-hosted pegmatites and minor aplite. The REE and high field strength element (HFSE)-bearing phases are hosted primarily in pegmatites as relatively fine-grained phases or pseudomorphs. The gangue phases comprise of quartz, feldspar, amphibole, and pyroxene. Potential ore minerals comprise predominantly of kainosite, gerenite, gadolinite, zircon, pyrochlore, and gittinsite. These complex mineralogical characteristics increase the difficulty for processing and provide a challenge for choosing the correct reagent scheme in rougher flotation. Process options including reverse flotation to reject the gangue minerals and de-sliming prior to the direct rougher flotation were investigated. Optimization trials were conducted using various reagent regimes and under different flotation conditions. Encouraging results were found using a combination of collector reagents supplied by Cytec Canada Inc.

Jan 1, 2014

By L. C. S. Dharmasiri, S. M. Shin, A. Senaputra, J. S. Sohn, K. H. Park, J. Avraamides

Reducing agents can be applied to leach metal values from natural and secondary resources such as laterite ores and deep sea manganese nodules and recycled materials such as spent batteries / catalysts which contain high-valent metal oxides of manganese, cobalt and iron. Selective leaching of some metals can be achieved by selecting conditions to control the saturated solubility and dissolution rates of metals from oxides or mixed metal/oxide matrices. The leaching results are rationalized on the basis of chemical species, Eh-pH diagrams and heterogeneous kinetic models. The role of reducing agents such as hydrogen peroxide, sulfur dioxide and iron(II) sulphate, in acid, alkali and in the presence of complexing ligands such as ammonia for the improvement of the leaching of metal oxides and metals is discussed. Previous studies on acid leaching of metals from nickel laterites, manganese nodules and spent catalysts/batteries in the absence or presence of reducing agents show that the rate controlling step involves the diffusion of protons through a thickening product layer on the particle being leached. It is shown that the leaching of nickel and cobalt from manganese nodules and zinc-carbon batteries in ammoniacal sulphur dioxide solutions also obey shrinking core kinetics.

Jan 1, 2014

By T. Sun, J. Kou, C. Sun, China Railway Resources Group Limited

"The polymetallic sulfide ore in Jiama county of Tibet contains 0.78% Cu, 0.046% Mo, 0.31 g/t Au and 17.9 g/t Ag in average. However, heavy loss of valuable metals was observed using high-pH process and Butyl xanthate as the collector. In this paper, the flotation was optimized through the adoption of a novel collector C-7, which is a mixture of xanthate ester and thionocarbamate. This collector showed better flotation performance under weak base conditions. The recoveries of Cu, Mo, Au and Ag increased to 93.24%, 84.60%, 78.13% and 75.41%, respectively, under 15 g/t of C-7 at pH of 8.0. The adsorption mechanism of C-7 was investigated by micro-flotation tests, zeta potential measurements, FTIR analysis and adsorption quantity measurements. Chemisorption of C-7 on chalcopyrite surface is demonstrated with adsorption density 3.8 times higher than on pyrite.INTRODUCTIONXanthates are the most commonly used collectors of strong collecting ability for separating copper sulfide minerals from gangue in froth flotation. However, the selectivity of xanthates themselves is poor to realize separation of chalcopyrite and pyrite whose floatability are quite similar (Heyes & Trahar, 1977; Chandraprabha, Natarajan, & Modak, 2004). High pH process with xanthates as collectors is proved effective in copper-sulfur separation and is widely used in treatment of copper sulfide ore flotation (Smith, 1996; Valdivieso, Cervantes, Song, Cabrera, & Laskowski, 2004). This method could get ideal separation results, but large amount of lime must be added, and could bring about increased cost, device corrosion and environmental pollution. In addition, there could also be high depression and heavy loss of associated noble metal such as Mo, Au and Ag. Consequently, a large amount of research has been conducted on substitutions of xanthates for selective flotation of copper sulfide ores under low pH conditions (Gholivand, Khodadadian, & Ahmadi, 2010; Li, 2010)."

Jan 1, 2016

By T. R. Yu, D. B. Counter

"In an effort to increase productivity, the use of fly ash as a binder for consolidated backfill was studied. From laboratory and underground tests f or its cementitious properties and environmental effects, it was found that a portion of Portland cement could be replaced by the same amount of type ""C"" fly ash to produce an acceptable consolidated rockfill product for use at Kidd Creek.The environmental concerns in terms of dust control and emanation of radon gas were unfounded from measurements. The dust count was comparable to the use of Portland cement only, or with ground blast furnace slag, and the radiation readings were low, averaging one-seventh the regulation level.Since May 1984, a total of over 100 000tonnes of fly ash has been consumed as a binder blended with Portland cement, producing over four million tonnes of consolidated rockfill. To date, the fill in the stopes has performed very satisfactorily, while yielding considerable cost savings.IntroductionThe Kidd Creek minesite, located 27 km north of the city centre of Timmins, Ontario, produces 4.5 million tonnes of base metal sulphide ore annually. The mining method for both No. I and No .2 mines is mainly sub-level blasthole stoping with delayed backfilling.No. 1 mine was developed with a shaft to a depth of 930 m in 1973 to recover the ore between the floor of the open pit at the 216 m horizon, and the 792 m horizon. Stopes are normally 18 m wide, 22 m to 65 m long, with heights varying from 90 m to 135 m. Vertical rib pillars between stopes are typically 24 m wide and sill pillars are 30 m thick.Pillar recovery is implemented after the consolidated rockfill placed in the mined stopes has cured for a period of at least three months. This allows a maximum recovery of the ore with a minimum of dilution, while also maintaining safe working conditions.No. 2 mine was developed from a second shaft, sunk to a depth of 1530 m in 1978, for the recovery of ore beneath the No. I mine. Sub-level stoping in No .2 mine is similar to No.1 mine in methodology, yet differs in sequencing, as no rib pillars are left."

Jan 1, 1988

Recently, renewed interest in the recovery of uranium from leach solutions has necessitated a re-examination of the hydrometallurgy methods used for uranium in the 1960?s to 1970?s. A synthesizing overview of the lessons learned in those decades together with examination of recent developments in this area is warranted. This paper considers uranium recovery chemistry from acid and alkali leach solutions using solvent extraction and resin ion exchange, and provides information on circuit selection and configuration, equipment selection and design, as well as operational considerations. The unique thermodynamics of uranium solvent extraction are also presented and discussed.

Aug 1, 2010

By C. J. Coulson, G. A. McKay, A. M. Cormie

"The Leitch mine, in the Beardmore area, Thunder Bay district, Ontario, is a part of the Leitch estate. It includes a group of patented claims, staked by P. A. Leitch of Port Arthur early in the century, along bands of jasper, hematite, iron-bearing slates, carbonatized schists, and greywacke, commonly known as 'iron formation'. The folding and shearing in these variably interstratified beds is a striking structural feature. The vein pattern is very definitely related to these structures.ROCKSThe rocks in the area are typical Keewatin lavas-greenstone-overlain by a series of Timiskaming sediments consisting of arkosic greywacke, iron formation, slate, greywacke, conglomerate, and greywacke, in this order from the contact. The sedimentary beds are generally conformable with the older rock contact except on local folds.Small intrusions of diorite occur as nearly vertical dykes and are believed to be of Algoman age. To the northwest of the mine there are larger intrusions of granodiorite belonging to the same period.Several dykes of quartz diabase up to 100 feet in width, striking generally north and south, with a vertical dip, cross the property. These have been classified by W. C. Laird as pre-Keweenawan in age. One of these dykes in particular is of importance for it cuts through the No. 2 vein and serves as a pillar when stoping. It is approximately 6 feet wide.The youngest rock type represented is a sheet of olivine diabase that extends over an area of thousands of square miles in and around lake Nipigon. It underlies most of this area and its outcrops form some of the most interesting topographical features, with fault scarps rising hundreds of feet. In the vicinity of the mine shaft the sheet is about 600 feet thick and extends from a depth of 1,871 feet to approximately 2,470 feet. It has a dense, hard, chilled margin and a sharp, tight contact. It intruded the sediments with very little lateral disturbance. The chief effect was baking, which darkened and hardened the greywacke near the contact. The sheet dips flatly to the cast."

Jan 1, 1954

By P. B. Marchant

"Based on laboratory and pilot scale continuous biooxidation of complex sulphide concentrates, commercial processing design and scaleup considerations are discussed. Capital and operating cost estimates for commercial biohydrometallurgical operations are summarized and potential applications of biotechnology are discussed. Biooxidation as an oxidative pretreatment alternative to enhance precious metals extraction from refractory sulphide concentrates in stirred tank reactors has received considerable attention recently due mainly to advances in the practical applicability of the process. Biooxidation of sulphides is certainly not a new process, however, application and control in large scale hydrometallurgical operations to treat refractory sulphides remains conceptual and the limited data available is restricted to relatively small laboratory and pilot scale operations. It is the intent of this paper to indicate scaleup and plant scale process design considerations for commercial bioleach circuits, based on recent operating experiences with laboratory and pilot scale continuous bioleach systems. An indication of the expected range of applications will be presented parameters for optimization will be discussed."

Jan 1, 1986