Search Documents

By G. E. Agar, R. Stratton-Crawley

"The applicability of a hydrocyclone model to simulation of the cyclone banks in a multi-stage sandplant circuit producing mine back fill has been demonstrated. The model ha~; been used in conjunction with a modular computer program for circuit simulation in order to study the effect of changes in the operating conditions. It has been shown that weight recovery to sand fill increases as feed percent solids decreases, and, to a lesser extent as pressure drop across the banks increases. An increase in apex diameter also causes an increase in weight recovery. Increased weight recovery must, however, be balanced against sump an1l cyclone capacity and dilution of sand fill by fines. The predicted results from circuit simulation were in good agreement with plant data.The model has been found to be applicable to widely different ores."

Jan 1, 1979

By V. Ramachandran

The successful advent of solvent extraction (SX) reagents for copper recovery and improvements in electrowinning of copper to produce LME grade A copper cathode have paved the way for the hydrometallurgical treatment of copper oxide and low grade sulfide ores. This has resulted in about 25-30% of the world's copper being produced today by the Leach-SX-EW process. The obvious next step was to develop processes for the hydrometallurgical treatment of copper sulfide concentrates, as an alternative to a typical smelter-refinery complex. The current paper updates the processes that have been developed to date with emphasis on processes that are being commercialized or that are seriously under consideration for commercialization. Most of the discussions relate to the hydrometallurgy of chalcopyrite concentrates, which account for about 70% of the world's known copper reserves. In summary, in the last thirty years, the hydrometallurgical treatment of copper sulfide concentrates has attained full maturity and will be a serious option to contend with while evaluating any future new copper plant.

Jan 1, 2007

By M. A. Keogh

This paper reviews the physical properties that make low-density polyethylene the most practical and economical material for launder• fabrication in the majority of mine and mill applications. The basic design features and use of other launcher• materials are also discussed.

Jan 1, 1976

By J. E. Gill, A. R. Byers

"The property of Sladen Malartic Mines, Limited, is in the northern half of Fourniere township, Abitibi county, Quebec. The group is large, but the part so far found to be of economic interest is a strip 3,200 feet long between the Canadian Malartic property to the west and the East Malartic and National Malartic properties to the east ( Fig. 1).The original claims were staked in 1923 and 1924 by St. B. Sladen and H. S. Kennedy because gold was known to occur on claims nearby. In 1928, detailed mapping of the Malartic Gold Mines property (now Canadian Malartic) showed the presence of an east-west gold-bearing zone traceable almost to the Sladen boundary. During the winter of 1929, a hand-driven drill was used to secure short sections of core through casing pipe sunk to bed-rock. This proved the existence of the main Sladen ore zone, but it was not until the price of gold was increased, in 1934, that serious work was attempted.Underground work was started in 1935 and milling in January, 1938. To the end of 1945, 168,882 oz. of gold were recovered from 1,641,974 tons of ore, an average of 0.103 oz. a ton.GEOLOGYThe bed-rock underlying' the Sladen Malartic property consists mainly of Precambrian greywacke and volcanics that appear to form a conformable series with a general northwest strike and vertical to steep northerly dip. Except where disturbed locally by drag folds or faults, tops face north. Intrusive rocks that range in composition from diorite to granite cut the sediments and volcanics. The basic types, generally quartz diorite and diorite, form dykes or sills in the volcanic rocks. The more acidic types, mainly quartz syenite and related porphyries, intrude the volcanics and the sediments in the form of dykes, sills, and larger, stock-like bodies.The orebodies are parts of slightly shattered or brecciated zones, mainly in greywacke, but partly in syenite, diorite, and volcanics, that have been more or less replaced by fine-grained quartz, pyrite, and minor amounts of sphalerite, galena, sylvanite, petzite, and gold."

Jan 1, 1954

By R. D. Brown

Ever since British Columbia started the ball rolling in 1974 with the introduction of its now-defunct Mineral Royalties Act, all Canada's resource-based provinces have significantly altered their mining tax systems. The last resource-based province to abandon its pre -1974 mining tax structure is New Brunswick, which introduced a new mining tax regime in the summer of 1977 to take effect from April 1 1977. The new structure, which represents the outcome of considerable study and discussions with industry representatives, contains some intriguing concepts which make Nero Brunswick's new mining tax system unique among the Canadian provinces.

Jan 1, 1977

By Lee W. T. Weitzel

This paper reviews the Falconbridge- SMRQ?s Raglan project in northern Quebec and the process that was used in developing its current long-term mine plan. Challenges were many and not only limited to the longevity of the project, numerous ore deposits (both underground and open pit), and a 40km property strike length. As a result of its remote northern location other factors such as progressive reclamation, leachable mine waste, water treatment, and waste management were also part of the plan. A combination of modern planning tools were used to formulate the plan including DataMine, Mine 2-4D, AutoMod Simulation, and an Excel based financial spreadsheet to bring the total plan together. The focus of this paper is to show the complexity of modern mine planning and associated economic modeling of mine processes.

May 1, 2002

By F. Mercier-Langevin

ABSTRACT; Agnico-Eagle’s LaRonde mine is one of the deepest mines in Canada. Ground conditions in the deeper levels can be very challenging, ranging from hard and brittle to soft and squeezing. As a result, rock mechanics and ground control practices have had to evolve considerably to accommodate progressively deeper mining activities. This paper focuses on the deeper levels of mines and how the difficult ground conditions encountered there have influenced the mining strategy. The first section examines ground control practices and support systems in highly stressed, poor quality rock. The evolution of level layout is also presented. Finally, improvements in stope sequencing are reviewed.

Jan 1, 2010

By Arnaud Faucher, Amar Sabih, Sudarshan Martins, Tristan Martin, Sami Makni, Peter Radziszewski, Poorya Hosseini, Francois-Raymond Boyer

The measurement of acoustic signals produced by a tumbling mill has been previously used to determine the operating state of the mill and correlate the variations of the sound intensity with the operating conditions of the mill. Separately, the discrete element model (DEM), a software simulation of the mill, was developed to provide insight into the operation of the mill. Presently, there has not been much work reconciling the DEM simulation of the mill with the acoustic signal. Working from basic principles of linear, time-invariant systems, agreement between an acoustic DEM simulation and the measured signal is sought. First, the impulse response function of the mill is measured. The DEM provides the forces applied to the mill shell as a function of time. A convolution of these simulated shell forces and the transfer function gives the simulated acoustic signal. This signal is compared to the measured acoustic signal, both in the time domain and the frequency domain. Finally, a discussion of the results is given.

Jan 1, 2012

By Kousuke Takahata, Hirofumi Yoshimura, Jun Nakahigashi

Studies of a protium treatment for grain refinement of a + ß type titanium alloy are reviewed and recent experimental results are introduced. Protium treatment consists of the following three processes: (1) protium absorption, (2) martensitic transformation and hot working, and (3) final treatment for protium desorption and recrystallization. A combination of these processes results in the ultra-fine grains of 0.3 to 0.5 µm in diameter with high angle boundaries. The ultra-fine-grained material exhibits superplastic elongation of over 9000%. Superplastic forming was successfully used to fabricate a denture base. These materials may be widely applicable as biomaterials in various medical industries.

Jan 1, 2004

By M. J. MONEA

Canada's only economic high-swelling bentonite deposit is mined in Wilcox, Saskatchewan, by A vonlea Mineral Industries Limited. The bentonite resulted from devitrified and altered volcanic ash released during the Laramide Orogeny. Volcanic ash was deposited in a pre-Cretaceous basin that was formed by salt solution collapse structures. Sedimentary rocks in the Wilcox area belong to the Snakebite Member of the Upper Cretaceous Bearpaw Formation. Bentonite beds are 61 cm, 46 cm and 30 cm thick; these are separated by 365 cm and 182 cm of shale respectively. Saskatchewan bentonite is used primarily in the oil well industry.

Jan 1, 1984

By C. L. Belyk

There are fifteen accepted types of uranium ore deposits and at least forty subtypes readily identified around the world. Each deposit type has a unique geological model which may also have unique processing implications. Primary uranium production in the past decade has come from a handful of these deposit types: unconformity, sandstone, calcrete, intrusive, breccia complex and volcanic. Processing implications for each of the fifteen deposit types can vary widely between and within different geological models. Some key characteristics of uranium deposits that may have processing implications include: ore grade, uranium and gangue mineralogy ? including clay and carbonate species and content, hardness, porosity, uranium mineral morphology, and carbon content. Processing roadblocks may occur as a result of one or more of these characteristics for any of the fifteen deposit types. Future technological advances and innovative thinking around uranium ore processing could provide avenues for roadblock removal setting the stage for additional and economically-viable uranium production from traditional and non-traditional uranium ore deposits.

Aug 1, 2010

By Zhang Wei

"Pulang Copper Mine is located in Shangri-La county, Diqing Prefecture, Yunnan Province, with currently defined copper reserve of 4.8 million tonnes of copper metal and an average grade of 0.34% Cu. The mineralized zone in a dome shape is 2,300 m long, 600–800 m wide, and 1,000 m high. At present, the project is at a construction phase, with a first-stage mining and processing capacity of 12.5 million tonnes of ore per year. Ore haulage is planned via a drift and ore pass development system. The cavability of mineralized rock is classified into three types (II, III, IV), with type III accounting for more than 98% of the total reserves. The cavability of the orebody is generally considered to be good and block caving mining method is planned. Semi-autogenous grinding and ball milling are adopted for the mineral processing. The tailing dam construction method is a center-line method.INTRODUCTIONAs the China's largest underground nonferrous mine, Pulang Copper Mine is located in the northeast of Shangri-La County, Diqing Prefecture, Yunnan Province, China. It is 62 km northeast of Shangri-La city. Shangri-La County is a Tibetan-dominated, multiple-ethnic region, with a population of approximately 163,000 in 2009. The county is rich in mineral and water resources, thriving with tourism. Its economy is also dominated by agriculture. To date, the defined copper reserves at the Pulang Copper Mine is 4.8 million tonnes of copper metal at an average grade of 0.34% Cu. In addition, it contains a gold reserve of 145 tonnes, a silver reserve of 2,754 tonnes, a molybdenum reserve of 0.19 million tonnes, and a sulphur reserve of 10.5 million tonnes. The first-stage mining and processing capacity is planned at 12.5 million tonnes of ore per year. When it ramps up to this production rate, the mine will produce copper concentrate containing 50,000 tonnes of copper and molybdenum concentrate containing 968 tonnes of molybdenum. A drift and ore pass system is planned for ore haulage and mining method is a block caving method. Semi-autogenous grinding and ball milling are considered for mineral processing. A center line dam is adopted for the tailing dam construction (Feng, 2010; Feng, Li, & Wang, 2011; China Enfi Engineering Corporation, 2014)."

Jan 1, 2016

By Carlos Nieble

Ferteco Mineracao, belonging to the CVRD group, is one of the several iron ore mines in the south east of Brazil. Some of these mines have pit walls of over 350-m height and operations under difficult geo-technical conditions are steadily increasing. In order to mine the 15 million tonnes of high grade hematitic ore remaining in the Fabrica pit, Ferteco had to deal with the following restrictions: Warrant power to its concentrator and pellet plant, relocate the load-out rail road loop, stabilise a poor phillyte slope, relocate a creek on a bench, lower the water table and mine at maximum angles at a slope with phillyte and loose itabirites directly under the rail road loop. Considering these aspects, 3 stages of operations were designed, considering a safe operation, but with the lowest possible security factors at the last mining stage, before the pit would be filled in again with tailings. Stage one above the rail road loop and below the high tension power mast, where the poor phillyte slope was secured by a flexible retaining wall, using old rails and anchors up to 27 meters (80ft) with a working pressure of up till 30 tonnes and stage two with different slope angles, and deep wells, high wall blasting perpendicular to the highwall with relief holes and rerouting the creek in steel half culvert and stage three, the filling in with tailings and recuperation of the deep well pumps. Following studies and analysis were made: Geotechnical and geological studies of all rock formations including rock strength test, a hydrological study to define the lowering of the ground water level, slope stability analysis for every bench and all possible combination of benches, definition of blasting parameters close to the pit slope, a monitoring plan, including topographical movements, vibrations due to blasting, piezometers and pressure cells as well as a plan how to fill up the pit again with tailings in combination with the rising of the ground water level. A close co-operation between the geo-technical consultant, pit operations, the blasting contractor and the geological department resulted in an operation without any incidents, lowering the pit with an additional 3 benches and mining an additional 5 million tonnes of high grade ore.

May 1, 2003

By Rodrigo Craig Cerello

The Brazilian economy has always presented a strong correlation with the mineral activity. Since colonization days, due to the territorial expansion caused by the explorers search for gold, mining in Brazil became a basic sector of national economy. Currently, the Brazilian mineral sector¹ estimates a 550% production increment (Figure 1A) in the last 10 years, reaching the US$ 50 billion value, reflecting the increased global demand for raw materials from mineral origin. According to the Brazilian Constitution², mineral resources belong to the Federal State and, consequently, their exploitation must be authorized, under penalty of engendering federal crime. Furthermore, activities of this nature are prone to cause environmental degradation such as, but not limited to, deforestation, pollution, soil deterioration and water contamination. The GPEMA represents the forensics group of the Brazilian Federal Police responsible for the technical analysis of traces related to crimes against the environment and consequently, illegal mining cases.

Aug 1, 2013

By Stuart McTavish

"The Brunswick Mining concentrator processes 10,000 D.S. T. per day of a complex sulphide ore. Four separate concentrates- zinc, lead, copper and bulk-are produced by selective flotation. Several major changes have been made to the Brunswick flotation circuit to improve the process and control. This paper will describe the present flotation practices at the Brunswick Concentrator. Special emphasis is given to the conversion of two of the primary circuits to an SO2-aeration flowsheet, and to the addition of a new secondary zinc flotation circuit that produces a zinc concentrate from the plant tailings. IntroductionBrunswick Mining and Smelting Corporation operates a zinclead- copper and silver mine and concentrator near Bathurst, New Brunswick. Since the start-up of operations in 1964, the flotation flowsheet has undergone major modifications to process the increased tonnages and to produce a greater number of concentrates. The flowsheet for the concentrator as it was in 1971 has been described by Neumann and Schnarru) and by Ersklneco. Since then, in 1971, the No.6 concentrator was converted from bulk flotation to selective flotation to produce a copper, lead and zinc concentrate. A separate zinc upgrading circuit was installed in 1972 and a bulk flotation or dezincing circuit, which reduced the zinc in the lead concentrate, was started in 1973. In 1976, the secondary zinc circuit was initiated.In addition to these new circuits, changes have been made to the existing circuits to simplify their operation."

Jan 1, 1980

By Chri Langille, Dougal McCreath, Samantha Espley

"In 1993, trials of two innovative applications of liner support involving the replacement of bolts in the ground support system were undertaken at Inco mines. The first trial involved an evaluation of the effect of dynamic loading on mesh-reinforced boltless shotcrete in a sub-level cave mining area on 2400 level at Stobie Mine. The second trial involved an evaluation of the MIROC Mineguard spray-on liner as a replacement for bolts and screen support, or as a replacement for screen support alone, in a topsoil heading of a bulk, VRM (vertical retreat mining) stope on 3240 level at Lower Coleman Mine.In the Stobie Mine trial, an uppers retreat heading was supported using a two-pass system. First, shotcrete was applied 2 inches thick, followed by pinning of mesh screen to the back and walls. A second pass of another 2 inches of shotcrete was then performed. For recovery of the ore zone, a vertical slot was created using a Borepak blind boring machine. The uppers rings were blasted, one or two rings at a time, starting at the slot and retreating out of the heading. During blasting of the production rings, blast monitoring was used to record the ppvs (peak particle velocities). For a series of 5-ring blasts, the maximum ppvs were measured to be 0.4 m/s (16 in./s) with a maximum charge weight per delay of357 kg (800 Ib). Six 5-point convergence measurement stations were set up and after each blast the total rockmass convergence was measured using a tape extensometer. Although a maximum displacement of 100 mm (4 in.) was measured, the shotcrete still managed to provide some support junction. A support damage assessment was also done to try and relate blast vibration to effectiveness of the mesh reinforced shotcrete liner. This trial demonstrated the effect that blasting has, on a support system, and it also demonstrated the necessity of having the mesh reinforcement properly placed within the shotcrete."

Jan 1, 1995

By Cheryl L. Allen

The increasing energy costs associated with mining has become an issue that needs to be addressed for future sustainable production. Vale Inco is undertaking a Ventilation on Demand (VOD) Project in an effort to minimize costs, continue to mine at depth and reduce green house gas emissions. A dynamic VOD system is very complex with potential high risk. Therefore, a systematic approach is being taken for successful development and implementation of the concept. The physical components of the system are currently being tested at various Vale Inco mine sites. While the operability of the physical components are being tested, the strategy for optimizing the architectures of the system is being defined. This presentation discusses the method of developing a VOD system at Vale Inco.

Feb 1, 2008

By F. P. Yungwirth

"IntroductionTrout Lake Mine is located about 5 km north of the Hudson Bay Mining and Smelting Co., Limited complex at Flin Flon, Manitoba. The mine was brought into production in 1982at the onset of a severe recession in the base metal market. The mine is operated as a joint venture with HBM&S, MMR and SMS.During the first several months of operation it became evident that there were opportunities to reduce costs at the mine significantly, and a productivity improvement subcommittee was formed to make recommendations. The first committee met in January, 1983 and consisted of the mine manager from Hudson Bay Mining, a geological expert and a maintenance expert from Outokumpu Oy, Finland, and a mine manager from Granges, Sweden.Recommendations from this committee were implemented during 1983 and a new subcommittee was constituted in 1984 to continue the work begun the previous year. The committee remains as constituted in 1984 and meets quarterly.The committee consists of M.A . Kirby , manager - Flin Flon Mines, HBM&S; Gustav Hoberstorfer of Mindelco , a Swedish mining consultant retained by Granges; Eero Laatio, mine superintendent of Keretti Mine at Outokumpu Oy in Finland; and Bob Bray, a mining consultant retained by Manitoba Mineral Resources.Many productivity improvements made in the operation are attributed to the work of this committee and other experts retained at various times throughout the mine life."

Jan 1, 1988

By J. G. Martin, J. C. Campbell

THE VICTORIA JUNCTION 31,4-million-ton coal preparation complex went into operation in October 1976."' It is designed to produce a metallurgical coking coal by lowering the sulphur and ash content of the raw coal using a heavy-media cycloning process to treat deslimed crushed coal, with scavenging of fine coal by flotation from the primary minus-28-mesh screen product. A secondary H-M cyclone scavenges a thermal-grade coal from the primary H-M cyclone tailing.

Jan 1, 1985

By Z. S. Shao, X. Z. Li

"Sub-critical crack growth plays an important role in long-term creep failure in brittle rock. Based on micromechanics established by using relationship between micromechanical wing crack growth model and macroscopic strain, and comparing theoretical model with testing results, a method, which applies the theory to real rock, is suggested in this paper. Using this method, properties of creep, damage and progressive failure in brittle rock are investigated. Effects of stress state on creep failure time and steady-state creep rate are analyzed and graphically presented. The results are helpful to support structure design and service life evaluation of underground structures with high geostatic stresses. INTRODUCTIONDuring the long-term operation in underground space with brittle surrounding rock, due to chemical action between pore water and rock, the failure of rock often occurs at stresses below its short-term failure strength, which brings serious effect on the long-term stability of underground structure. Thus, the long-term strength of brittle rock attracted wide interests of scholars around the world. The static fatigue limit was predicted by exponential function that is derived from abundant experiment data of stress level and failure time(Schmidtke & Lajtai, 1985), and similar result by relationship between stress state and failure time was also suggested (Lau & Chandler, 2004; Aubertin et al., 2000; Sangha & Dhir, 1972). According to relationship between steady creep rate and stress state during creep, a critical stress that transforms steady-state creep to accelerated creep was studied and the long-term strength was suggested (Tsai et al., 2008; Ma & Daemen, 2006; Lajtai et al., 1991). Based on the results of experiment in compression, the long-term strength of rock was defined by stress at volume strain reversal. When applied stresses are larger than the long-term strength, the microcracks in the rock will grow constantly, damage of rock will increase and failure of rock will occur finally (Chandler, 2013; Bieniawski, 1967; Brace et al., 1966)."

Jan 1, 2015