Search Documents

By Gabriel Zarate

"Los Bronces had two ROM dump leach operations designated Leach I and Leach II. Leach I was commissioned in 1998 and stopped in 2014 due to the mine requirements. Leach II plant, commissioned in early 2002, was built to treat around 700 million tons of marginal ROM ore averaging 0.45 % total copper. The mineralogy of this material was estimated to be 70% chalcopyrite, 20% chalcocite/covellite and the balance oxides.The original electrowinning plant design capacity for copper production was nominal 19,500 tonnes per year at a current density of 276 A/m2 and a current efficiency of 92%. Presently, Los Bronces San Francisco plant typically operates at current densities between 390 and 440 A/m2, much higher than the average in the industry, with current efficiencies around 93% and a maximum copper cathodes production of 37,200 tonnes per year.In order to accomplish these achievements, a number of modifications in the process conditions, in the cell hardware and in the operational procedures have been implemented. In the first case, the specific flowrate, copper concentration and temperature of the electrolyte were modified to accommodate the operational requirements facilitating the increased current density. Associated with the cell hardware, a six cells expansion was added, upgraded equipotential inner cell busbars were installed and the cross section of the cathode hanger bars was enlarged for increased current carrying capacity. Documented operational procedures like short circuit detection and cathode weight control were improved.The modifications implemented and the results obtained are discussed in this paper.INTRODUCTIONLos Bronces Division of Anglo American Chile is located up in the Andes Mountains, northeast of Santiago. It had two cathode plants, Los Bronces at an altitude of 3500 meters above sea level (m.a.s.l.) commissioned in 1998 and closed in 2014 and San Francisco at an altitude of 2800 m.a.s.l. and in operation since 2002.The process is leaching run off mine (ROM) low grade copper sulphide ore in dumps. The mineralogy of this material was estimated to be 70% chalcopyrite, 20% chalcocite/covellite and the balance oxides. The average grade is 0.45% total copper (Cut).At Los Bronces dump, Leach I plant, the pregnant leach solution (PLS) was collected and stored in an underground reservoir. From there, it was fed to a solvent extraction plant with a series-parallel configuration in two extraction stages and one stripping stage. The electrolyte produced was fed to the electrowinning plant having 30 cells and 60 cathodes per cell. Maximum capacity of this plant was 12,000 tonnes per year (tpy)."

Jan 1, 2016

By J. Larose, E. Irissou

The aerospace business has always been driven by innovation. A significant portion of the overall business technology development strategies is still based today on improved materials and coatings. In this highly regulatory business environment, large amounts of funding are required to increase the maturity level of novel technologies, but the evolution process still remains a delicate endeavor. The technical risks involved during technology development obviously need to be managed and mitigated throughout the development cycle, but other hurdles almost inevitably get encountered, such as budget limitations, transition from lab scale to production scale, loss of focus, intellectual property negotiations and supply chain integrity. This presentation will cover some of the issues raised when a great idea is slowly morphed into an aerospace production part.

Jan 1, 2010

By Chris J. Pritchard

Pumpable, two-component resins for anchoring rock bolts provides significant advantages over traditional cartridge resin and cement grout systems where fast and easily adaptable support is required for difficult ground conditions. Cartridge resin anchoring with rock bolts is often ineffective in oversized, fractured and washed-out holes. Cement grouting of cable bolts is frequently plagued with QA and QC issues related to the grouting process. Installation of cable bolts with resin injection techniques is routinely completed in cycle allowing blasting immediately after cable bolting. Xstrata Nickel has evaluated the Minova Resin Injection System since 2007. The Nickel Rim Mine and partner Minova have tested and validated the Resin Injection process for bolting procedures including Hollow Fiberglass Bolts, Rebar, Modified Cone Bolts and Cable Bolts. The resin injection process is adaptable to most bolting processes and equipment. Currently, Nickel Rim Mine use 2 resin injection products with different set times to grout deep cable bolts and development support in highly variable ground conditions. The product predictability and adaptability in application along with a high crew acceptance continues to make this support process part of an adaptable ground support system. Product consistency and quality significantly reduce the quality control concerns for ground support in highly variable ground conditions.

May 1, 2011

"The gravimetric dust sampler is one of the tools now available to the industrial hygienists for determining the worker 's exposure to the numerous types of particulate matter that may be present in the workplace. The paper ' reviews the different sampling trains that can be used for the two major criteria for respirable dust and some of the sources of error in this dust assessment technique.IntroductionIt may be stated simply that the measurement of airborne dust in the working environment is done for one or two reasons: namely, for engineering control purposes and! or to evaluate the potential for toxicological insult arising from the inhalation of dust particles.This paper reviews the progress made in the development of dust-assessing instruments, particularly the gravimetric types designed to meet British and U.S. dust criteria , and discusses the limitations in their use for this purpose."

Jan 1, 1981

By Robert B. Parsons

"The annual onslaught of provincial budgets and tax changes is complete, and once again the Canadian taxpayer is being asked to dig deeper into his pocket to fund old and new programs. It is noteworthy that 1987 tax reform promised lower taxes, but a broader fax base. Five years later, we still have the broader tax base, but the lower faxes have gradually crept up to pre-tax reform levels. Surprise! Surprise!IntroductionThe last edition of Tax Notes commented on some important proposals announced in Manitoba's 1992 budget. In this issue, Tax Notes summarizes the 1992 budget proposals of British Columbia, Ontario and Quebec. These budgets reflect the continuing trend of transferring responsibilities and the related costs-from the federal government to the provinces. As well, the budget papers bear witness to the respective governments' political stripes. British Columbia, Ontario and Quebec are seeking higher tax revenues. Only Quebec continues to acknowledge the importance of the mining industry in its annual budget documents."

Jan 1, 1992

By Tom Shumka

INTRODUCTION ?This bull gear inspection technique was developed to provide more accurate data and faster inspection times than current techniques used today. ?Eddy Current Array (ECA) is a non-destructive testing technique that provides the ability to electronically drive multiple eddy current coils, which are placed side by side in the same probe assembly. Each individual eddy current coil in the probe produces a signal relative to the phase and amplitude of the structure below it. ?This data is referenced to an encoded position and time and represented graphically as a C-scan image. Most conventional eddy current flaw detection techniques can be reproduced with ECA inspections; however, the remarkable advantages of ECA technology allow improved inspection capabilities and significant time-savings.

Oct 1, 2010

By W. Dresler

"A major Canadian chromite deposit at Bird River, Manitoba is one of the largest known chromite reserves in North America but it exhibits low chromium contents and low chromium to iron ratios. Commercial beneficiation techniques permit these ores to be upgraded to concentrations which, however, remain inferior to most other ores and concentrates used worldwide f or production of high-carbon ferrochromium. Analyses for reduction of low-grade concentrates by submerged-arc electrofurnace techniques predict chromium contents between 45.9% and 51% for a high-carbon ferrochromium alloy. Relatively high over-all chromium recoveries between 79.5% and 91. 1% can be achieved. Alloy compositions for Cr, Fe, C and Si are determined for various burdens with low-grade concentrates. Consumption data per ton contained chromium are obtained for electric power, coke, concentrate, quartzite and limestone. The data are compared with those of high-carbon ferrochromium producers in South Africa. Economic aspects are discussed and compared with a South African reference study.IntroductionThe present ferrochromium demand in the western world is estimated at approximately 1.7 Mt with a consumption of approximately 0.36 Mt in the U.S.III and 0.03 Mt in Canada'-', A low estimate of the installed production capacity for ferrochromium in the non -communist world is 2.4 Mt. This production capacity of ferrochromium by far exceeds the demand, which is also evident from the fact that no shortage in supply of ferrochromium to the world markets was encountered in the past. Supply-demand comparisons therefore suggest that in the foreseeable future no new chromite or chromium producers should enter the world markets unless superior chromites or superior technologies are successful in competing with existing producers. Neither one of these conditions exist presently in Ca nada or the U.S., although essentially no ferrochromium is produced and no chromite is mined in these countries at the present time."

Jan 1, 1986

By Tatyana Alexandrova

The problem of processing refractory (rebellious) gold ores is important for all the countries involved in recovering precious metals from ores. Technological aspects of processing precious metal ores are examined in two respects: enhancing gold recovery from double refractory ores; and using carbonaceous ores on a production scale. The dispersed carbonaceous matter (DCM) present in concentrates causes the adsorption of [Au(CN)2]- complex on their surface during cyanidation process. Depending on the degree of graphitization and the organic carbon content in DCM (including kerogens and bitumen), the technology used to recover precious metals varies considerably. The problem of processing refractory (rebellious) gold ores is important for all the countries involved in recovering precious metals from ores. Depending on the degree of graphitization and the organic carbon content in DCM (including kerogens and bitumen), the technology used to recover precious metals varies considerably. The possibility of rare metals recovery, including rhenium, from black-shale rocks, has been examined. Comparative assessment of analytical methods of rare metals detecting has been carried out. It has been proved that neutron activation analysis is a promising technique. It has been shown that colloid-salt fraction (nanofraction) with particle size less than 1000 nm makes up to 3 wt% of black shale samples and is extracted by water under special conditions. The use of water instead of chemically active reagents provides insolubility of the mineral matrix and fully reflects the colloid-salt element of the samples. To sum up, the justification of the choice of technology for processing of carbon-bearing ores is based on examining the type of carbonaceous matter and its adsorption behavior. When the content of carbon of high degree of metamorphism is considerable, it is possible to recover platinum group elements and rare elements from this type of ores. The obtained results predetermine the general guidelines for creating new methods and techniques of processing carbonaceous material for integral development of solid minerals in the mining and oilfield areas of Russia.

Jan 1, 2016

By G. B. Harris

A process for the recovery of copper from the waste oxide copper of a mined-out sulphide orebody is described. Hydrometallurgical recovery of copper from this and similar wastes has been tried several times previously without success. Leaching is carried out by sulphuric acid in columns under conditions that minimise the iron content of the pregnant leach liquor, and copper is then recovered by ion exchange rather than the more conventional solvent extraction. The resin is stripped by spent electrolyte and copper is electrowon. Results are presented for testwork originally carried out in 1993, and repeated in 2006, and the novel aspects of the process, leaching and ion exchange, are discussed. Finally, preliminary order of magnitude capital and operating costs are given, demonstrating that the process is cost effective.

Jan 1, 2007

By Larson. William

What is Lunar In-Situ Resource Utilization (ISRU)? ISRU involves any hardware or operation that harnesses and utilizes ?in-situ? resources to create products and services for robotic and human exploration In-Situ Lunar Resources ???Natural? Lunar Resources ??Discarded Materials Lunar ISRU Products and Services ??Excavation, Site Preparation, and Outpost Deployment/Emplacement ??Mission Consumable Production ??Outpost Growth and Self-Sufficiency Benefits of ISRU ??Increased science and exploration hardware (instead of consumables) ??Increased safety, crew exploration time, and self-sufficiency ??Technology spin-in/spin-offs help recycling on Earth & space economy

May 1, 2009

By A. Pranowo, G. R. F. Alvear F., N. Aslin, M. S. Moats

"The toxicity of arsenic is well known and documented; however, the presence of arsenic in copper electrorefining anodes and electrolytes is critically necessary to produce high-quality cathode. Arsenic as well as antimony and bismuth concentrations vary relative to their concentration in the anode copper received from the smelter. The behaviour and benefits of arsenic in copper electrorefining and the detrimental effects of antimony and bismuth on cathode quality and tankhouse performance are discussed. This will include the minimization and mitigation of problems associated with arsenic, antimony, and bismuth—including cathode contamination, floating slimes, scaling, and anode passivation.RÉSUMÉ La toxicité de l’arsenic est bien connue et documentée; toutefois, la présence d’arsenic dans les anodes de l’électroaffinage du cuivre et dans les électrolytes est d’une nécessité critique pour produire une cathode de grande qualité. Les concentrations en arsenic, ainsi qu’en antimoine et en bismuth varient selon leur concentration dans l’anode de cuivre reçue de la fonderie. Le comportement et les avantages de l’arsenic dans l’électroaffinage du cuivre et les effets indésirables de l’antimoine et du bismuth sur la qualité de la cathode et le rendement des cuves d’électrolyse sont discutés. On traite aussi de la minimisation et de l’atténuation des problèmes associés à l’arsenic, l’antimoine et le bismuth – incluant la contamination de la cathode, les schlamms flottants, l’entartage et la passivation de l’anode."

Jan 1, 2016

By K. Janghorban

Multilayered ceramic-metal composites were produced by solid state diffusion bonding of polycrystalline alumina and three Al alloys containing 1 to 2%Sr, 2% Mg and Mg + Si (5057 Al alloy), The multilayered structures were fabricated at 610°C under a compressive stress of 3 MPa for 2 hours in He-5%H atmosphere, The ceramic-metal interfaces were studied by SEM and TEM equipped with energy dispersive spectrometer (EDS). Addition of 1 wt % Sr to Al promoted good adhesion, without producing any interfacial products, while the Al-2%Sr was poor in this regard due to the presence of dispersed A14Sr which is an intrinsic phase in the Al-Sr phase system, The Al-2%Mg alloy produced a continuous film at the interface, which was characterized to be MgAl2O4. Al alloys containing Mg and Si (5057 commercial alloy) produced not only the spinel structure (MgAl2O4), but another phase rich in Mg and Si (close to Mg2Si), These latter interfacial reaction products were not the intrinsic phases in Al-Mg alloys, and were reaction products at the Al2O3 ?Al alloy interfaces.

Jan 1, 2005

By W. R. Hopkins, J. A. Davis

"This paper presents a discussion of the mechanisms by which aerosols of the process electrolyte are entrained into the breathing environment of copper, Zinc and nickel eIectrowinning tankhouses. Literature outlining the health effects associated with worker & posure to the acidic and metallic contaminants found in the airbome aerosols is summarized and compared with existing North American regulations.A brief review of the existing technologies for the source reduction of these aerosols is presented. This paper outlines the industry experience with use of covers, balls, beads, shapes, fixtures and chemical surfaetants. Each of these devices is ranked according to its effusiveness in the process in which it is used, and rated according to its operator acceptance.The various forms of existing in-plant ventilation systems are reviewed with a discussion of their relative merits and effectiveness. Actual experience is related, detailing the methods of testing for ambient contaminant levels in a variety of tankhouse environments. Guidelines are provided for the site and process specific criteria which govern the selection and ultimate effectiveness of a particular form of ventilation system.Finally, actual project experience is cited in which hydraulic modelling is used a design tool in tankhouse ventilation design. These projects include the upgrading of existing traditional ventilation designs, and the ''grass roots"" design of a more efficient aerosol source control system to be used in high altitude, cold weather sites."

Jan 1, 1994

By V. S. Sastri, M. Elboujdaïni

"Corrosion rates of silicon brasses, highzinc yellow brass, low-zinc yellow brass, leadedtin bronze and silicon bronzes in both permanent-mold and sand-cast conditions were determined in soft water of pH 3, 5 and 8, and hard water of pH 8 at 70°C by electrochemical polarization technique. The alloys in permanent- mold condition showed greater corrosion resistance than sand-cast condition. Corrosion rates obtained from weight loss measurements showed no observable trend of a difference between permanent-mold and sand-cast alloys.The corrosion rates decreased with increasing pH of the medium. Silicon bronze and silicon brass showed high corrosion resistance while leaded-tin bronze showed the least resistance. Addition of small amounts of aluminum improved the corrosion resistance of silicon bronzes and silicon brasses. Alloys in permanent- mold condition showed greater resistance to dezincification than sand-cast alloys when average pit depth parameter is considered."

Jan 1, 1997

By Y. H. Hatzor

"This is an extended abstract for a keynote lecture delivered by the author during the 2015 ISRM congress in Montreal on the application of the numerical discontinuous deformation analysis (DDA) method in rock mechanics practice. Due to the large scope of the topic this lecture will focus on studies performed by the rock mechanics group at Ben-Gurion University, alone or in collaboration which other research groups, and is not intended to provide a comprehensive review of everything that has been done on the subject worldwide during the past two decades. A forthcoming textbook (Hatzor et al., in preparation) will attempt to provide such comprehensive coverage.DDA has been developed by Dr. Gen-hua Shi while he was doing his PhD studies under the supervision of Professor R. E. Goodman at U. C. Berkeley (Shi, 1988). Dr. Shi has invented a new numerical discrete element method which provides a solution for dynamic deformation of block systems, hence its applicability to rock mechanics practice. The method is similar in essence to the finite element method in its implicit formulation of the time integration scheme and where in every time step the minimum potential energy of the entire system is sought, but here every element is a finite block with six degrees of freedom. The blocks are assumed to be stiff (simply deformable) so that most of the energy is consumed by slip along pre-existing discontinuities, the frictional resistance of which is assumed to obey the Coulomb-Mohr failure criterion for rock joints. The greatest advantage of DDA over alternative numerical discrete element methods is its robust area (volume) integration which ensures great accuracy even when the blocks are of irregular shapes, including non-convex blocks which may contain holes. The greatest disadvantage is the necessity to solve in every time step very large matrices of unknowns, imposing great CPU demand when the block system involves a large number of blocks. Another disadvantage is the sensitivity of the solution to the choice of the penalty parameter which is implemented in DDA in the form of stiff springs that are attached to contacts once detected automatically.The inherently dynamic formulation of the DDA method lends itself to solution of dynamic problems in rock mechanics. Dynamic analysis with DDA can be performed in different ways corresponding to different rock mechanics problems and loading conditions. Three main classes of loading conditions which are relevant to rock mechanics applications are discussed here: 1) dynamic loading of a single bock which rests on a stationary foundation, 2) response of a block to dynamic loading of the foundations, 3) wave propagation through a block system.The most common approach is to introduce the dynamic force to a specific block in an otherwise fixed block system and check the resulting deformation, typically the time dependent displacement or rotation of the loaded block. This approach is particularly useful for dynamic rock slope stability studies when a stability of a specific rock block against earthquake vibrations is in question. The first 2D-DDA benchmark test of this approach was performed by Hatzor and Feintuch (2001) who introduced harmonic acceleration functions into a block which rests on an inclined plane. The analytical solution proposed for this problem by Hatzor and Feintuch (2001) was later generalized by Kamai and Hatzor (2008). The first 3D-DDA benchmarking for this approach was presented by Bakun-Mazor et al. (2012) who studied single and double face sliding of blocks which rest on stationary foundations and subjected to harmonic input acceleration functions."

Jan 1, 2015

"ChairmanThis part of the discussion is intended as an exchange of information between those who have installed rubber liners in their mills and a means of others to get information that may help them decide if rubber liners would be applicable to their mills.To start the discussion and to relate it to the previous section of this symposium Mine Equipment Co. Ltd. have supplied some graphs that will give some idea of the noise suppression that may be expected from the u.se of rubber liners instead of steel. The figures used in preparing the graphs came from installations of rubber liners in Sweden.L. Strah - Mine Equipment Co.The graph, Figure 1, shows on the bottom the octave band range. The noise level generated by the steel liners is represented by the dotted line and lies within the shaded area where it is considered that hearing damage may result. The solid line represents the noise level generated by rubber liners in the same mill and you will see it is below the shaded area. Although it is not marked on the graph I think the decibel range is from 7 5 to 115. The next one, Figure 2 which shows the relative noise levels generated by steel balls and pebbles with both steel and rubber liners shows the decibel range."

Jan 1, 1968

By D. S. Cronan, S. P. Varnavas

Abstract - Metalliferous precipitates from submarine hydrothermal discharges have been investigated at four inshore locations off Milos in the Hellenic Volcanic Arc. The fine fraction of the sediments shows considerable variability in the concentrations of elements frequently associated with hydrothermal activity. Manganese varies from 30 ppm to 2500 ppm, encompassing the entire range of values found off Santorini also in the Hellenic Arc. Iron occurs in lower concentrations than off Santorini and Yali, while other elements often associated with hydrothermal activity such as Pb, Zn, As, and Cu also show enrichments in sediments from the hydrothermal vent areas. Selective leaching studies have shown that most elements are variably distributed between the different phases of the sediments but with enriched Pb, Zn, and Mn mainly in easily soluble secondary phases. Hydrothermal inputs are strongest at Palaeochori Bay, less at Voudia Bay and lowest at the Airport Springs and Rivari. The weathering of sulfide and possibly other orebodies is also thought to contribute to some of the elements enriched, while background concentrations are largely supplied from detrital sources.

Jan 1, 1999

By G. Zárate, G. Tapia

Anglo American Chile has been doing copper concentrate leaching studies at the laboratory and small pilot plant scale since 1992. Among the processes evaluated are bacterial leaching and pressure leaching using Mantos Blancos, Salobo Project and Quellaveco Project concentrates. Late in the nineties, it was decided to focus the research on pressure leaching, either medium or total pressure oxidation. Preliminary scouting tests were run with Mantos Blancos concentrate samples during 2000, which were repeated during 2003 together with samples of Los Bronces and El Soldado concentrates, in order to define the most suitable concentrate for running a pilot plant campaign at AARL, which was carried out in two campaigns, a first one from November 2003 through January 2004 and a second one during April 2004. Mantos Blancos was the selected concentrate and the laboratory and pilot plant results are discussed in this paper together with some preliminary economic estimates.

Jan 1, 2004

By L. Li

Iron removal is a common procedure in hydrometallurgy of non-ferrous metallic ores. Chemical precipitation and solvent extraction are currently the main methods employed for separation of iron from copper leach solution. However, chemical precipitation methods have the problem of producing large amounts of iron precipitates, and/or requiring high temperature and high pressure conditions for precipitation. The precipitates are difficult to separate from the solution. Emulsification is a general problem for solvent extraction, which causes loss of extractants and contamination of the electrolyte. A common problem for solvent extraction and chelating ion exchange processes is the difficult iron stripping process. Therefore, finding an efficient and environmentally friendly method for iron removal is of great significance. In this paper, new processes of using ion exchange resins to remove iron from copper leach solution have been investigated. Salicylic acid, amino carboxylic acid, amino phosphonic acid and hydroxy-oxime resins were employed to adsorb iron from a simulated copper leach solution containing 40 g/L of Cu2+ and 36 g/L of Fe3+. It was found that a hydroxy-oxime resin, named Z-Fe, has excellent adsorption selectivity on Fe3+. Desorption behavior of the resin was studied by two step elution using dilute H2SO4 and oxalic acid solution, respectively. After optimizing the adsorption-elution processes, the extent of removal of iron from the simulated copper leach solution using resin Z-Fe was 90%, while copper recovery could reach 100% in closed circuit processing.

Jan 1, 2016

By Gary Walters, Thomas Gonzales, David George, William Davenport, Andreas Siegmund, Suping Yao, Shijie Wang

The previous survey of world copper smelters was in 2016 (Copper, 2016). The copper smelting industry has grown and improved considerably since then, including continuing growth in China and modernization in Japan (Extraction, 2018). Outotec flash smelting and Outotec flash smelting/Kennecott - Outotec flash converting continue to be adopted while newer processes continue to be adopted in China. In addition, some of the world's original flash furnaces have been completely rebuilt (Extraction, 2018). This paper provides recent industrial production data and discusses these new developments. INTRODUCTION A world copper survey was redone in 2016 after a thirteen year lag since 2003. Some of the notable changes were the significant increases in production particularly from China. Since then, several smelters have gone through modernization processes and decommissioning of older technologies. This paper will review the notable changes since the last publication at Cu2016. In the last paper, Copper Smelting: 2016 World Copper Smelter Data, the author gave an audible sigh after observing that copper smelter sites as well as new and notable smelters have been spreading like wildfire in China since 2003. Indeed, seeing is believing. Figure 1 shows the Ningde Copper Smelter (double flashing, 400,000 MT Cu/Year capacity) that started up producing copper in 2018; Figure 2 shows the Nanguo Copper Smelter that is under construction with 300,000 MT Cu/Year capacity (first phase, side blown smelting and continuous top blown converting). We should not only admire the Chinese copper industry’s significant technological developments, but also the copper price support that it has provided throughout this century.

Jan 1, 2019