Search Documents

By R. J. R. Welwood, F. J. Grebenc

"Brunswick Mining and Smelting Corporation Ltd. (controlled by Noranda Mines Limited) operates two lead-zinccopper- silver mines approximately 20 miles inland from Bathurst, N.B. The principal No. 12 orebody is mined by underground methods; the second, the No. 6 orebody (6 miles away), is recovered by open-pit mining. No. 12 underground operations ar•e in two parallel massive sulphide orebodies about 400 ft apart, dipping at 75 to 80 degrees and plunging almost vertically. The initial mining phase involved longhole open stoping from the 1550 level to the crown pillar, with main levels at 150-ft intervals and sub-levels between at 75 ft. Stope dimensions average 120 ft long, 100 ft wide and 400 ft high, with alternate rib pillars as well as sill and crown pillars. Initially, ore was transferred through scram drifts below each stope by means of 125-hp electric slushers and 72-in. folding scrapers, being delivered to gravity ore-pass collection •systems feeding a primary jaw crusher below. Later, track and trackless drawpoints were utilized below most longhole open stopes and pillars. Rib pillars were recovered by longhole methods, with large blasts into a central slot and undercut, after adjacent stopes had been filled. Waste-rock stripping from No. 6 open pit has been supplied to No. 12 stopes as backfill, by means of gravityfill raises.In 1968, the decision was made to mine the remaining ore zones by mechanized cut-and-fill methods, utilizing Load-Haul-Dump equipment. Currently, approximately 60 per cent of No. 12 mine production comes from mechanized cut-and-fill mining. As before, backfill is supplied from No. 6 open pit stripping waste rock, which has been crushed to minus 6 in. The ultimate objective is to supply virtually all production requirements by mechanized cut-and-fill techniques. The No. 6 open pit, which commenced production in 1966, covers an area of 1,500 by 1,200 ft, equivalent to 41 acres approximately. Ramp roads are graded at 8.5 per cent. Each mining bench is 36 ft high and the ultimate pit will consist of 14 benches for a final pit depth of 504 ft. Present depth is 180 ft."

Jan 1, 1971

By Frank Arthur Forward

FRANK ARTHUR FORWARD was born in Ottawa and attended the University of Toronto, where he received a B.A.Sc. in chemical engineering in 1924. From 1924 to 1929, he was a smelter operator and research metallurgist with the Consolidated Mining and Smelting Company of Canada Ltd. (Cominco) at Trail, B.C. Moving to Australia in 1929, he was assistant smelter superintendent, Mount Isa Mines Ltd., Queensland, until 1934, when he returned to Canada, spend-ing one year as metallurgist with B.C.

Jan 1, 1970

By J. E. Sepulveda, R. Morrow

"The Linear Wear Theory provides a reliable framework for the assessment of grinding media performance at full scale. This theory can be applied for analyzing grinding media consumption rates in any given grinding operation as well as the evaluation of alternative grinding media products, based on actual operational data, correcting for conditions like ore hardness, feed and product sizes, mill power and circuit throughput; all of them unrelated to the grinding media intrinsic quality attributes. A series of Moly-Cop Tools 3.0 applications have been developed to facilitate the calculations involved. Moly-Cop Tools 3.0 is available, free of charge, to all interested parties through the corresponding author.INTRODUCTION Mineral grinding circuit operators recognize the significance of grinding media (balls) consumption on the cost structure of any full scale grinding facility. The effective cost associated with this essential consumable depends on two factors: delivered price and durability (quality) of the grinding media. When evaluating alternative grinding media varieties, there is a well accepted evaluation criterion by which a given media type is considered to be “cost-effective” when its unit application cost – normally expressed in $/ton of ore ground – is shown to be lower than that of a nominal reference condition: Grinding Media Cost = Ball Price x Ball Consumption (1) ($ /ton ground) ($/ton balls) (ton balls/ton ground) Under this criterion, an alternative, higher-price grinding media product could be “cost-effective” if its associated consumption rate is sufficiently lower than the reference media, enough to yield a lower grinding cost, as dictated by Equation 1. For the proper application of the above criterion, evaluators must rely on representative indicators of grinding media quality, ideally independent of most mill operating conditions. In each particular case, ball price is always a known component; however, it is not so evident how media performance (quality) differences amongst alternative product types could be assessed with a reasonable degree of accuracy and precision."

Jan 1, 2014

By S. Sundararajan, J. Brousseau, P. Bocher, M. Galopin, N. Barka

This research is committed to the prediction of the hardness profile produced by induction heating, using a computer-modeling software. The paper presents the simulation of the induction hardening process to analyse the sensitivity of the induction parameters on the hardness profile of a low alloy steel specimen. The developed numerical model includes the coupling effect between electromagnetic and thermal fields, and takes into account the non linear behaviour of the material properties. The study applies an enlightened experimentation method to build the feasible domain of the process and to achieve predictive empirical modeling. The ultimate goal is to replace the trial and error method that is usually used for the development of new parts, by costless experiments with the numerical model. Further development of this approach will lead to the computation of the residual stresses and finally to the assessment of the mechanical properties of the part. The end result will be the ability to shorten the development time and to improve the quality of the hardened part.

Jan 1, 2006

By B. Schulz, T. Leißner, R. G. Merker

"Ores enriched in critical rare earth elements (CREE) keep on being of particular interest. The CREE are Nd, Eu, Tb, Dy, including Y. In conjunction with beneficiation tests on Y-mineral bearing flotation tailings of complicated mineralogy, the Mineral Liberation Analyses (MLA) was used to work out processing characteristics fraction-wise in terms of modal mineralogy, mineral recovery, locking and liberation, and particle size.Size fractions from mechanical sieving (“real fractions”) as well as fractions created virtually by using filters on the MLA-data of the unsieved head material (“virtual fractions”) were investigated comparatively thereby. The ""virtual-sizing-approach"" features a much simpler sample preparation procedure and considerably lower cost if a fraction-wise investigation of a head sample is needed. It can be conveniently applied to intimately locked ores needing a fine grinding to a particle size distribution (PSD) range below 25 microns for instance. However, its practical use is sometimes disputed in terms of the reliability of the results. Results are shown for the main Y-bearing mineral xenotime and selected main gangue minerals of a low grade REE-ore.The influence of sample representativeness, sample preparation and particle counting statistics turned out to be of crucial importance. Given that all preconditions for reliable results are met, locking characteristics, modal mineralogy, and even PSD trends can be read from virtual fractions.The authors encourage processing engineers to use the virtual approach. They propose practical measures to improve the reliability of the MLA results, identify and tackle conflicting results, and mitigate evaluation problems that may arise."

Jan 1, 2016

By O. Rabeau, M. Legault, F. Fallara

"Abstract - The development of robust 3-D geological models involves the integration of large amounts of public geological data, as well as additional accessible proprietary lithological, structural, geochemical, geophysical, and diamond drill hole data. 3-D models and maps have been available, particularly in the petroleum industry, for more than 10 years. Here, we demonstrate how robust 3-D maps can be used as interactive tools for mineral deposits exploration. In particular, we show how the interrogation of 3-D data sets can constrain exploration targets at depth. The main advantages of this technique for the mining industry are the homogeneity of data treatment and the validation of geological interpretations, taking into account geophysical and geochemical data. Data integration and cross-correlation of geology and geophysics can be achieved in two dimensions in any good GIS package. However, the added strength of 3-D analysis is the integration of separate data sets in three dimensions to build more complete, more realistic models, and in delineating areas of high economic potential at depth. Furthermore, these models can be modified and improved at any time by adding new data from ongoing drilling and geoscientific surveys. This paper presents two examples of 3-D models used for mineral exploration: the Joutel VMS mining camp and the Duparquet gold camp, Quebec. In both examples, the creation of the model is discussed and queries specific to the relevant exploration model are introduced. Eight potential exploration targets are generated at Joutel and seven at Duparquet. Although the targets defined are dependent on the details of the chosen queries, it is apparent that this technique has the potential to generate promising exploration activity that can engender new targets. Sommaire - Le développement de modèles 3-D géo-intégrés fiables implique l’intégration de grandes quantités de données géologiques publiques ainsi que des données lithologiques, structurales, géochimiques, géophysiques et de forages en provenance du secteur privé. L’industrie pétrolière dispose de modèles et de cartes 3-D depuis plus de 10 ans. Ce manuscrit présente un exemple d’utilisation de modèles et de cartes tridimensionnels détaillés comme outils interactifs dans l’exploration de dépôts métallifères. L’emphase est mise sur le processus d’interrogation des données en 3-D pour la définition de cibles d’exploration en profondeur. Les avantages principaux de cette technique sont l’uniformité du traitement des données et de la validation des interprétations géologiques, tout en tenant compte des données géophysiques et géochimiques. L’intégration de données et la corrélation de la géologie et de la géophysique peuvent être accomplies en deux dimensions dans n’importe quel logiciel SIG. La plus grande force de l’analyse 3-D demeure cependant la possibilité de construire des modèles complets et réalistes permettant de cibler des secteurs à haut potentiel économique en profondeur. De plus, ces modèles peuvent être modifiés et améliorés de manière interactive en ajoutant de nouvelles données provenant de forages et de levés géoscientifiques en cours. Ce manuscrit présente deux exemples de modèle 3-D géo-intégrés développés pour l’exploration minérale : le camp de SMV de Joutel et le camp aurifère de Duparquet, Québec. Dans les deux cas, la construction du modèle est décrite et les requêtes spécifiques à chaque type de gisement sont présentées. L’exercice a permis de définir huit cibles d’exploration potentielles à Joutel et sept à Duparquet. Bien que les cibles identifiées dépendent des contraintes utilisées pour les requêtes choisies, cette technique permet de générer de nouvelles cibles qui pourraient relancer l’activité d’exploration dans les camps miniers " matures " ou dans des secteurs moins explorés."

Jan 1, 2006

By Kurt D. Mitchell

"This paper discusses general application for A C variable frequency drives in the mining industry. A review of induction motors characteristics, adjustable frequency controller fundamentals, and three commonly used controllers is presented. General application guidelines for the three different types of controllers; variable voltage input , current source input and pulse width modulated are then reviewed in detail, and an example of the economic benefit of this technology is discussed. IntroductionSoon after static DC variable speed drives were well established in industry, a need for static AC variable speed drives was seen. The first technical papers describing possible systems appeared in the mid-1960s, with commercially available units arriving in the early 1970s. Without exception, static AC drives are substantially more complex than their DC counterparts, but they have some very desirable properties. As compared to DC motors, AC motors are less costly, physically smaller, more reliable, require less maintenance , easily sealed, have good load regulation, are able to run at higher operating voltages, and have little danger of over-speed runaway . These properties are particularly desirable in explosion-proof, submersible or difficult accessibility applications.Variable speed AC drives are now a proven technology. available in packages from Sub-horsepower to hundreds of horsepower, from 115VAC to 4160 VAC. This paper covers the principles of operation of three common types of controllers, application criteria, motor consideration and finally an example of how an AC variable speed drive can pay for itself in terms of energy savings."

Jan 1, 1986

By G. R. Heffernan

"IntroductionTHE PURPOSE of this paper is to give a •brief history of iron and steel in British Columbia, a quick look at the present operations of Western Canada Steel, Limited, a review of iron ore resources and iron and steel markets, and a projection of what the future might hold for the industry in British Columbia.From the Past to the PresentWhile the paper is entitled Past, Present, and Future, in covering the past, which we shall call the time prior to 1947, there is very little to be said. Small shipments of iron ore were made from the Texada deposits by the Puget Sound Iron Company from 1886 to 1907. Total ore shipped did not exceed 70,000 tons. Part of this is believed to have been used in building a United States battleship in 1907 in the Bremerton Naval Yards in Seattle, Washington.In 1914 a small steel mill was started on Lulu island, rolling bars from •box piles and used shafting. This mill operated spasmodically for a few years but finally burned down in 1921. The rolling mill stands were sold to China and are no doubt in operation in China today.In 1916 the City of Port Moody assisted in the financing of a mill which operated on re-roll rails, box piles, and steel ingots made in an experimental electric furnace in Port Moody. This furnace also produced small quantities of pig iron scrap. The backers of the Port Moody mill showed a great deal of enterprise and must have been a very forward looking group, since this was one of the first recorded applications of the electric furnace to small ingot production. Despite their enterprise, the operation was unsuccessful and terminated in 1921."

Jan 1, 1953

By W. E. Lockley

This paper will attempt to answer a number of questions which are important to the safe and continued operation of an electric power system. 1. WHY should electrical protective devices be tested? 2. WHAT devices should be tested ? 3. WHEN should they be tested ? 4. HOW should they be tested? 5. WHO should test them ?

Jan 1, 1977

By Laura A. Sanders

Mineral scale formation is prevalent in numerous mining operations. Such scale formation can occur in the direct-contact heat exchangers ahead of an autoclave. In these heat exchangers, the incoming slurry comes into contact with steam in a stage-wise fashion, which is re-circulated from the downstream flash vessels to heat the slurry in stages ahead of the autoclave. Calcium sulfate scaling causes severe problems in mining operations where increased temperatures are involved due to rising temperatures promoting calcium sulfate scaling through a decreasing solubility. In a number of these operations, the scale formation can occur in the presence of mineral solids, where fine-grained charged particles are at concentrations in excess of 35%. Scale prevention is not difficult in standard aqueous systems; however, the presence of solids leads to significant deficiencies in the prevention of scale due to the adsorption of the polymer onto the charge solids instead of the polymer interaction with the scale. Therefore, a technical solution to prevent mineral scale build up occurring in presence of pulp slurry in mining operations is needed. Several novel antiscalant technologies were developed and evaluated which provided a substantial improvement in the scale prevention in such systems.

May 1, 2013

By R. P. Townsend

It is a widely accepted "fact" that a Koepe friction hoist is generally the best solution for production hoisting when compared to a double drum hoists. This would appear to be true if one looks at the initial capital cost of just the hoist, and also if one compares the size of the motors selected for the duty. But is this the whole story? What are the longer term costs involved in the hoist's operation, and what are the relative efficiency's of the two designs? Perhaps the Koepe hoist design enjoys a better reputation than it deserves.

Jan 1, 2011

By C. Tasker

Introduction In the Early part of 1930 the Ontario Research Foundation was asked by the Minister of Mines, the Hon. Charles McCrea, K.C., M.P.P., to undertake a technical and economic investigation of the Northern Ontario lignite deposit. This investigation has been under way since June, 1930, and has necessitated considerable work at the deposit, in the laboratories of the Foundation, and at test plants in Europe. All the work has been carried out in active co-operation with the Provincial Department of Mines, the Deputy Minister, Mr. T. F. Sutherland, and several of his technical colleagues being associated with members of the staff of the Foundation on the Advisory Committee, which has met at frequent intervals to co-ordinate and direct the various lines of research. An interim report was made to the Minister of Mines by the Director of the Foundation, Dr. H. B. Speakman, at the end of December, 1932, and is at present under consideration by the Minister. This report deals with the extent and character of the deposit, the methods and costs of mining, and the methods and costs of processing raw lignite, the characteristics of certain lignite products, and the technology and economics of present fuel utilization by railways, industry, and domestic users in northern Ontario. It is not the purpose of the author to discuss in this paper either the geology of the deposit or the economics of the mining, processing, and utilization of lignite, but rather to deal briefly with some of the technical problems investigated by the Foundation during the study of the characteristics and methods of utilization of Northern Ontario lignite. Some mention, however, of the work carried out to define the extent of the deposit is a prerequisite to any discussion of the nature of the lignite.

Jan 1, 1933

By H. Dean

"Mine hoisting machinery, of which wire rope is an essential part, is developing, in Canada as well as in other parts of the North American continent, into highly sophisticated equipment. Heavier payloads are now required to be raised from steadily increasing depths at higher rates of speed and production. These hoisting conditions have, of necessity, brought about a major change in the production of steel roping wires and the wire ropes manufactured from them.Operators and designers of hoisting equipment are requesting a very much more efficient ratio of strength to weight in hoisting ropes, so that heavier loads may be raised from greater depths by ropes which will provide a predeterminable life span on which the operator may depend.The cost of wire rope to the operator is very low indeed, usually less than $0.01 per ton of payload, but the cost of unexpected shutdown periods, due to rope maintenance or change, can be extremely high -particularly in operations where a continuously high rate of production is an absolute necessity. Mine hoist ropes with a higher strength to weight ratio are now being made and used in some areas of Canadian mining, and a general understanding of the performance we may expect from them is required."

Jan 1, 1968

By A. Plumtree

The morphology of environmentally assisted cracks in stressed pipeline steel has been investigated. For a dilute and neutral solution (NS4) simulating ground water in contact with the steel, semi-elliptical cracks grow faster on the surface (2c) than in the depth (a), hence, the aspect ratio (a/c) decreases. This is explained using a deterministic concept since corrosion is dominant and the primary constraint is the conservation of charge. By contrast, when mechanistic conditions prevail, significant growth occurs in the depth. When underloads are imposed in the loading history, temporary accelerations in crack growth occur because corrosion rather than mechanical effects become dominant.

Jan 1, 2005

By L. D. Snyder, J. K. Russell

"The Lower Jurassic Iron Mask batholith intrudes Upper Triassic Nicola Group volcanic rocks in the Quesnellia terrane of southcentral British Columbia and hosts Cu-Au mineralization. The batholith comprises three mappable intrusive phases, including: Pothook gabbro to diorite, Cherry Creek monzodiorite to monzonite and Sugarloaf diorite. The Iron Mask hybrid forms a fourth mappable unit that makes up to 45% of the areal exposure in the batholith. It is highly variable in texture and composition and subdivided into three types; Type I and II have abundant (partially digested) xenoliths, many of which are derived from the Nicola Group, whereas Type III is xenolith-poor and shows extreme outcrop-scale textural diversity.Pothook and Cherry Creek rocks are similar in texture, mineralogy, whole rock and mineral composition and style of alteration. Contacts between the two can be intrusive or gradational. Rocks collected from these two suites have compositions that are permissive of a single magma batch, although simple crystal fractionation does not explain all chemical variations within and between the two suites. The Sugarloaf unit comprises a diverse group of amphibole-phyric rock types and is texturally and mineralogically distinct from Pothook and Cherry Creek suites.The Iron Mask hybrid represents progressive stages of physical and chemical interaction between Nicola Group country rocks and Pothook magma. Magmatic assimilation (selective or partial) is supparted on the basis of field relationships, petrographic observations, and REB compositional data. Thermal dehydration and partial assimilation of Nicola Group rocks by Pothook magma is shown to be a valid means of promoting early and extensive volatile saturation in the Iron Mask batholith."

Jan 1, 1995

The morphology of environmentally assisted cracks in stressed pipeline steel has been investigated, For a dilute and neutral solution (NS4) simulating ground water in contact with the steel, semi-elliptical cracks grow faster on the surface (2c) than in the depth (a), hence, the aspect ratio (a/c) decreases, This is explained using a deterministic concept since corrosion is dominant and the primary constraint is the conservation of charge, By contrast, when mechanistic conditions prevail, significant growth occurs in the depth, When underloads are imposed in the loading history, temporary accelerations in crack growth occur because corrosion rather than mechanical effects become dominant.

Jan 1, 2005

By G. A. Brown

"Mining executives are becoming increasingly involved with decisions of the ""What would happen if ... "" variety. Potential changes in government policy, such as tax incentives, E.G.M.A. allowances, etc. affect the economic future of present and proposed mining ventures.This paper will discuss various measures of effectiveness normally used in assessing this future, such as discounted cash flow, etc., and will describe means of introducing uncertainty into the computations. As the recognition of risk and attitudes toward accepting it are very important in the life of a mine executive, there will be a brief discussion of utility theory and its application to risk analysis.Risk models are usually of a size to warrant the use of an electronic computer. Therefore, to demonstrate the simple interaction necessary between a financial analyst and such a model, data will be read into a remote computer from a time-sharing terminal in the meeting room. It will be shown that changes may be rapidly made and alternative policies investigated ""on line"" to a computer."

Jan 1, 1970

By A. Dreimans

Tracing of 'float' against the latest ice-flow directions ha!' led to or assisted in discoveries of several mineral deposits in Canada at lP.ast since 1891, e.g., fluorite and corundum in eastern ?Ontario, Steeprock and Josephine iron ore in western Ontario, Malartic, Fisher-Quebec, and Lamaque gold ore, and Vendome zinc ore, in western Quebec, Sullivan zinc and lead sulphides in British Columbia, Orvan Brook or New Calumet sulphide deposit in New Brunswick, Lynn Lake nickel sulphide de-posit in Manitoba, etc. Pebbles or ore boulders whose source has not yet been found include diamonds in the Great Lakes region and ?sulphides in several localities in Ontario and Quebec. Complexity of transport of ore boulders, including non-glacial transport, may be the explanation. Tracing of ore boulders requires knowledge of the Pleistocene history of each particular area (ice flow directions, their ?changes during glacial oscillations, existence of pre-glacial lakes with ice-rafted boulders, later interference by streams, lakes, mass movements). Important also is distinction of till from similar non-glacial deposits and knowledge of the bed-rock geology. Quantitative methods, e.g., pebble counts, maybe applied while tracing magnetite, hematite, or goethite. Fragments of sulphide ores are less abundant in indicator trains, and quantitative methods are less suit-able for tracing them. Heavy-miner-al investigations may give good results for minerals resistant to weathering. Geochemical methods are of value only in the vicinity of ore deposits.

Jan 1, 1958

By K. Himbeault, D. Campbell, N. C. Garisto, D. A. Orava, A. Rosaasen

"The level of scientific knowledge about the effects of contaminants is increasing and changes in environmental monitoring are likely to allow for the assessment of environment effects particularly to the aquatic environment. This paper provides an overview of recent developments in this area which include the environmental effects monitoring program for pulp and paper operations, the assessment of the Aquatic Effects of Mining (AQUAMIN) program, the Aquatic Effects Technology Evaluation (AETE) program, and the review of the federal Metal Mining Liquid Effluent Regulations (MMLER). The paper also provides a look forward at the direction of environmental monitoring of mine projects in Canada. IntroductionEnvironmental monitoring programs provide a wide range of data to environmental management systems, regulatory authorities, and stakeholders. The data obtained are used to demonstrate that operations are in compliance with regulatory environmental protection requirements, and provide the scientific basis for assessing the effectiveness of environmental protection measures. Environmental monitoring requirements for mine projects are established based on the type of operation, site specific issues and concerns, and the requirements of regulators and mine proponents.The level of scientific knowledge regarding the potential effects of contaminants on the receiving environment is increasing, and in particular with regards to the receiving aquatic environment. Regulatory controls regarding the protection of fish, fish habitat, and fishery resources are being reviewed with regards to their adequacy, and the environmental effects monitoring program on the pulp and paper industry is expected to provide useful data relevant to those types of operations. These developments are of interest to mine proponents as it is presently expected that an environment effects monitoring program will be developed specifically for the metal mining industry under a regulated environmental effects monitoring program as part of the Fisheries Act. This paper reviews recent developments in this area, and provides a look forward on the future directions of environmental monitoring programs."

Jan 1, 2000

By W. T. Robson

ONE of the problems encountered in any mine is the effect of increasing pressure manifested by increasing depth. Although the depth at which excessive pressure assumes serious proportion, and the manner in which it appears in underground workings, are influenced by a variety of factors, nevertheless the difficulty is present in all mines and its gravity increases with increasing depth. In the Kirkland Lake camp, as far back as seven years ago, mining had proceeded to depths sufficient to result in the formation of pressure great enough to cause violent disruption of masses of rock. It is proposed in this paper to deal with the effect of pressure caused by mining as observed at Lake Shore Mines, and to describe some of the methods which have been adopted to counteract it. There are many contributing factors in a study of the problem, and results vary widely in individual mines and in different localities. One feature common to all, however, is that there is ground subsidence, evidenced either by a gradual settling accompanied by crushing and shearing of the ore and wall-rocks, or the disruption of the ground surrounding the periphery of an excavation may take place suddenly, attended by more or less violent shattering of the rocks. Such violent failure of a mass of rock has been designated by the term rock-burst. The history of rock-bursts extends over a great number of years. They have occurred in some form or other in practically ali places where mining operations, at all but very shallow depths, have been carried out. Since the theoretical aspects of the subject have been dealt 'with at great length by capable and experienced writers (1), the present paper will give only a brief résumé of the theories propounded by those engaged in deep mining operations in various parts of the world.

Jan 1, 1940