Search Documents

By E. Sharifi, B. Komishke, R. Heffel, D. Schwartz

"The oil sands resources in Canada are one of the world’s largest hydrocarbon deposits. Processing of oil sands uses hot water to extract bitumen. The process generates tailings slurry that must be settled for final deposition. The tailings contain fine material, with poor water release characteristics which makes water recovery challenging. Polymer flocculants are added to assist in settling and dewatering the fine tailings. The amount of polymer addition is dependent on tailings characteristics, including the particle size distribution (PSD). If the PSD of the tailings is unknown, an excess amount of polymer needs to be added in the dewatering stage to flocculate the particles. Over flocculation also has a detrimental effect on the water release characteristics. Measuring the particle size distribution using an on-line analyzer could have major benefits over common laboratory methods as it provides online and fast insight into the process enabling the operators to implement required changes to minimize the reagent consumption, while achieving optimal flocculation. Online measurement of PSD using laser diffraction has long been used in base metals beneficiation processes. A series of test work using Outotec PSI500® particle size analyzer on oil sands samples from different operations have been conducted. Tests were performed by recirculating the slurry in closed circuit to simulate real plant conditions. This paper presents a summary of the results.INTRODUCTION Canada’s oil sands are the third largest reserves of crude oil in the world, with an estimated 165.4 billion barrels of recoverable oil (Government of Alberta 2016). Oil sands are a mixture of sand, water, clay and bitumen. Bitumen is a form of oil that is too heavy or thick to flow or be pumped without being diluted or heated. About 20% of bitumen reserves are close enough to surface to be mined. In mining methods, oil sand is transported from an open pit mine to the processing plant and bitumen is separated from solids and water. The separation process involves ore preparation, such as addition of hot water, steam and caustic (NaOH), followed by gravity separation and froth treatment (Masliyah et al. 2004). A general scheme of the extraction process is presented in Figure 1."

Jan 1, 2018

By R. W. Lawrence

"In the past year, BioteQ Environmental Technologies Inc. have initiated design and construction of new plants to add to an existing list of plants that utilize the BioSulphide® and ChemSulphide™ process technologies for metal recovery and water treatment. In these plants, low cost biogenic sulfide or, in some cases, chemical sulfide reagent is used to selectively remove metals from contaminated water. The process produces high grade, marketable, metal sulfide products even from low grade feed solutions. The revenues generated from the sale of products can allow for water treatment at a profit in some cases, offset treatment costs in others, and generally reduce sludge disposal and management costs. The effluents produced from the process can meet stringent environmental standards. Current plants in operation and under construction range in sulphide demand from 50 kg/day to 3.7 tonnes/day, with the feasibility of larger plants with sulfide demands ranging from 6 to 43 tonnes/day under review.Biogenic sulfide reagent can also be considered for other applications in hydrometallurgy and mineral processing. Uses under consideration by a number of mining companies include: (1) replacement of sodium hydrosulphide in the SART process for cyanide regeneration and copper recovery in the processing of gold-copper ores, and (2) replacement of sodium hydrosulphide for use in the separation of copper and molybdenum in flotation. Biogenic sulphide, produced on demand at site, offers significant cost savings and provides the additional benefit of improved safety due to the elimination of the transportation, handling and storage required for chemical sulphide reagents.This paper reviews the applications of the BioSulphide® and ChemSulphide™ technologies for water treatment and metal recovery, and introduces projects where biogenic sulfide can be applied in hydrometallurgy and mineral processing."

Jan 1, 2007

By G. Plascencia, C. López, J. González, D. Jaramillo, M. A. Barrón

Air jet and molten matte interaction within a Peirce - Smith converter is analyzed during the first stages of blowing using Computational Fluid Dynamics (CFD), by means of the Large Eddy Simulation and Reynolds Stress turbulence models. Jet velocities ranging from 5 to 150 mis, which involve the bubbling and open jet regimes, were considered in 2 and in 3-D numerical simulations. As a result of the computer simulations, it was found that low velocities results in gas bubbling in the molten copper, whereas higher gas velocities results in well defined plumes. The consequence of such different behaviours results in an increment in the rate of refractory wear or in copper splashing respectively. The analysis of the results may lead to improve the design of the tuyeres currently used in copper converting. Bottom blowing of air is also explored in this work. Numerical results show a strong non-linear parabolic behaviour of the jet velocity on the average velocity of copper; which means that beyond certain jet velocity, the copper de-accelerates thus reducing its velocity. This may be due to the open nature of the jet, which prevents the momentum transfer from the injected gas to the molten copper.

Jan 1, 2007

By Subrata Dutta

Sindesar Khurd Mine is situated in Rajasthan, India, and operated by Hindustan Zinc Ltd, under Vedanta Group. The base metal mine is high in reserves of Lead, Zinc and silver and has been producing since 2007 with initial production of 0.3 mtpa. Recently the mine has gained prominence as a base metal underground mine in introduction of latest mining techniques and achieving high production at lowest costs. The promising Lead-Zinc reserves of Sindesar Khurd Mine (SKM) and high-tech exploration adopted by Hindustan Zinc Ltd (HZL), (Vedanta Group), raising the reserves and resources from a meager 9 Mt (1997) to 81 Mt (2012), has prompted HZL management to ramp up the mine production from 0.3 mtpa (2006-07) to 2 mtpa by 2013-14 with ambitious plans to reach 3.5mtpa subsequently (presently largest underground metal mine in India). The complete trackless system underground mine, recently equipped with latest leaky feeder communication system (unique in India), utilize modern drilling, mucking and hauling equipment aided with various utility/service vehicles. Excavation optimization and quality recovery maximization from the open and post filled stoping methods, continual expert analysis and feedback from International consultants like AMC (Australia) and SRK (UK), and involvement of renowned bodies in management excellence, have lead the mine towards highest productivity and lowest mine operating cost, earning the mine a prominent place in the global base metal industry. The paper deals with how the various challenges in mine planning and designing, mine development, operator skill, equipment introduction and maintenance, expertise availability, provide training and exposure to officials, prompt and effective communication/service, control of ground vibrations, maintain ventilation standards etc are faced in attaining high operational excellence and thus attain a record mine output/man shift (OMS) of 14 ton/man shift with targets to reach 20 ton/man /shift. Scientific designing using 2D/3D numerical mine-modeling techniques, faster stope sequencing with introduction of paste filling ( first time in India),latest leaky feeder communication system, control ground vibration to stringent standards using electronic delay system, faster raising techniques using raise borers to enhance development and ventilation, cavity scanners to monitor large stope voids, fast shaft sinking at 100 m/month(Chinese expertise) and maintaining adequate ventilation with close software monitoring are some of the highlights discussed in the paper towards achieving the targets.

Aug 1, 2013

By Ertugrul Alp

Alp & Associates - Who We Are ?? Canadian consulting company (1999-?) ?? Principal Consultant: Dr. Ertugrul Alp, P.Eng. ?? Over twenty-five years experience serving the chemical, mining, pulp & paper, energy, steel, and transportation industries, and government clients. ?? Ph.D. in Mechanical Engineering, University of Waterloo ?? Experience: ?? Westinghouse Canada, Atomic Power Division, Manager, Analysis and Modelling ?? Concord Environmental (later Bovar Environmental), Principal, Manager, Air Quality and Risk Assessment ?? Arthur D. Little, Associate Director, Safety & Risk Practice Leader in Canada ?? Member: NATO CCMS Pilot Project on Disaster Preparedness (1991-1993) ?? Chair: MIACC Risk Assessment Expert Committee, 1995-1999 ?? Member: MIACC Committees on Land Use Planning and Pipelines (1993-1998) ?? Member: CSA/Q850 Risk Management Standard Technical Committee ?? Member: CSA/Z1002 OHS Risk Assessment Standard Technical Committee ?? Member: CCPA/CSChE Process Safety Management Committee (1999-?) ?? Member: ISO-31000 Risk Management Standard Canadian Advisory Committee ?? Chair: CSChE Process Safety Management Committee (2005-2006) ?? Chair: CSChE Expert Committee on Risk Assessment (1999-2005) ?? CSChE 2007 Process Safety Management Award

May 1, 2008

By H. C. M. Gordon

IT is essential to the success of any mining op::ration that the roadways through which the material wrought and ocher materials and supplies are to be transported should be kept in such condition that this transportation cart be effected rapidly and without difficulty. The longer the roadway and the greater the tonnage to be taken over it, the more necessary it becomes chat the construction and maintenance of the road be such chat traffic delays can be reduced co a minimum. le is proposed co deal with the development and construction of roadways serving longwall operations and, since a recreating system of longwall is worked, as a rule, only where roadways driven in the solid coal can be readily maintained, the discussion will be confined co advancing longwall roads which are driven through areas from which the coal seam has been totally extracted. In order to construct a roadway through extracted ground in such a manner that it will remain in a state of reasonably good repair without undue maintenance, it is necessary chat everything possible be done to bring the overlying strata co a state of equilibrium as quickly as this can be effected, and the operations should be so planned that future workings will not disturb the equilibrium so set up more than can be avoided. Obviously, the readiest way to obtain a stable roadway is to develop it by tunnelling through a settled waste. However, this cannot always be done, as some of the roadways must be developed and constructed as the walls progress, but level or lateral cut-offs can be constructed in this manner. Main-slope roads can be developed in a similar manner after the coal has been extracted and a waste formed for at !east five hundred feet on either side of the line of the permanent roadway from temporary subsidiary roads developed for this purpose along one or other of the flanks of the waste to be formed. This interval must be obtained in order chat the lacer extraction of the seam will not set up movements in the waste immediately overlying or adjacent to the constructed roadway, thus upsetting the equilibrium of the strata and distorting the road.

Jan 1, 1940

By B. Arlyuk

On the basis of research of relations among the market participants the analytical model has been created which connects the price of industrial good at stock exchange with volume of sales and the stock of the sellers and buyers, Also a model was developed for assessment of these parameters of the market status by the actually fixed stock exchange and general market indicators. The composition of these models made it possible to create reliable system of short-term price forecasting for commodities or base metals up to one quarter ahead. Imperfectability of creation a model for reliable price forecasting by purely statistic methods (by the "black box" principle) was shown. A model of price behavior qualitative forecasting till one quarter ahead has been developed, which determines the probability of reaching in future of the given level as well as of the price maximums and minimums, Optimal values of threshold probability were determined for forecasting the future price maximums and minimums securing the maximum profit from the forecasting system application for commercial activity. The developed system of forecasting was identified for primary aluminium at the period of 1990-2003. The system was tested daily during 20 months period for speculations on 3M primary aluminium forwards at London Metal Exchange with high commercial result.

Jan 1, 2004

By Yuanming Pan, Brett Rogers, Baoquan Hu, Gary Yeo, Christine Austman

The nature and distribution of radiation-induced defects (RIDs) in quartz from the Maw Zone, a yttrium- and rare-earth-element-enriched sandstone breccia complex exhibiting intense hydrothermal alteration, have been investigated by electron paramagnetic resonance (EPR) spectroscopy. EPR spectra show that detrital quartz in sandstone, from five diamond drill holes intersecting the Maw Zone and one above the crest of the so-called Quartzite Ridge, contain only background-level RIDs, indicating that Ubearing fluids were absent in this area. However, close to the sandstone-basement unconformity, in hole WR-194 immediately west of the Quartzite Ridge, the concentration of RIDs in detrital quartz is significantly above background but at least an order of magnitude lower than those at the Key Lake and McArthur River deposits. Widespread drusy quartz at the Maw Zone, which signifies intense hydrothermal alteration, is associated with hematite-, sulfide- and carbonate-bearing mineral assemblages, which exhibit complex crosscutting relationships. EPR spectra of drusy quartz in all three types of mineral assemblages are low in RIDs as well, supporting the EPR evidence that fluids at the Maw Zone did not carry significant U. These EPR results suggest that, in spite of intense hydrothermal alteration and favorable structural geology, the Maw Zone is unlikely to host any significant U mineralization. Moreover, this study shows that the EPR technique is potentially a useful exploration tool, capable of determining whether individual alteration zones in the Athabasca Basin were associated with U-bearing fluids or not.

Jan 1, 2013

By S. Luidold, A. Poscher, H. Antrekowitsch

"The rare earth elements (REE) are nowadays mainly used for permanent magnets, catalysts, hydrogen storage alloys in rechargeable batteries, for glasses, ceramics, and polishing agents. Other important areas of application are phosphors in different types of lamps (fluorescent tubes, energy-saving lamps, etc.). These lamps are often collected and treated at their end of life by disintegration and sorting. However, the obtained fine fractions comprise not only REE-containing phosphors but also small amounts of mercury and are therefore disposed till today in special landfills. Due to the enormous price increase of the rare earths during the last two years, a lot of activities started for extracting these elements from secondary resources such as for example phosphors. All recycling concepts for this task mainly work with hydrometallurgical methods. The large number of different compounds in phosphors with sometimes very different behaviors with respect to their solubility in aqueous phases forms a major challenge to achieve good yields as well as acceptable purities of the produced rare earth concentrates by a process with a reasonable number of operation steps. Therefore, this paper gives at first a brief overview about the compounds, used as phosphors and about existing concepts or investigations. It further describes our own process design and the results, obtained on laboratory scale. INTRODUCTIONThe rare earth elements (REE) have a central position in the industrialised world despite their marginal production volume in comparison to common metals such as aluminium, copper, zinc etc., because they are essential for many applications. They often cannot be substituted without a considerable loss on functionality and quality. This group of metals comprise the lanthanoids (f–block elements, lanthanum–lutetium) as well as scandium and yttrium.The estimated world mine production of REE amounted to 133,000 t rare earth oxide equivalent in 2010, whereat China accounted for 130,000 t or 98 % (Cordier, 2012). The European Union (EU-27) imported 23,013 t in 2008 to cover its demand. The figure 1 shows the fraction of the European member states in terms of the total imports of rare earth compounds from outside the EU-27 (Schüler, Buchert, Liu, Dittrich, & Merz, 2011)."

Jan 1, 2012

By Y. Zedan

In this study, the statistical design of experiments (DOE) was applied to study and regulate the properties of near-eutectic Al-11%Si alloys. Develop regression equations for such response variables as hardness, yield stress, ultimate tensile stress, percent elongation, total cutting force, cutting power, and tool life together with other factors which, include the percentage composition of the alloying elements, and the requisite modification (Sr) level. These equations may be analyzed quantitatively to acquire an understating of the effects which the main variables and their interactions may have on the mechanical behaviour and the machinability of the alloy under investigation. The results reveal that increasing the levels of Cu and Fe content results in an increase in hardness, yield stress, and ultimate tensile strength in both modified and non-modified alloys. On the other hand, both Cu and Fe appear to affect the percentage elongation adversely, whereas the Sr-level has a positive effect on this parameter. It was found that Sr-levels have the most significant effect on the cutting forces and cutting power followed by the content in Fe and Cu. The results also reveal that the interaction coefficients of these variables have a significant effect on tool life compared to the main independent variables. This fact may be attributed to the formation of complex insoluble phases between Cu, Fe, Si, and Al as investigated using Scanning Electron Microscopy (SEM) attached to an EDX analysis system. The accuracy of the regression equations in predicting the expected properties has been verified by carrying out random experiments in the range of variation of these variables.

Jan 1, 2011

By A. Hashempour, D. Javani

"Selection of an optimal bit is a critical issue in drilling engineering. Specific energy (SE) and Cost per Foot (CPF) are the most common methods for evaluation of bit efficiency and optimal bit selection. The major shortfall of both methods is that they do not directly account for geological and geomechanical parameters of formations being drilling. In this paper, results of using the two foregoing methods are compared using Formation Drillability (FD) method, which directly accounts for geological and geomechanical parameters of a formation. This method combines various geological and geomechanical parameters and yields a dimensionless parameter indicating the formation drilling hardness (drillability). Results of this study show that the amount of energy, cost and time spent for drilling a unit volume / length of an identical formation may vary in different wells. This is due to the fact that geological and geomechanical characteristics of a formation may vary among wells and even within short intervals of a single well. Therefore, an optimal bit may not be appropriately selected, if drilling and economical parameters are the only factors considered and the formation geological and geomechanical specifications are ignored.INTRODUCTIONMany authors such as Bilgesu, Al-Rashidi, Aminian, and Ameri (2000) and Clegg (2006) conducted research in the evaluation of bit performance and optimum bit selection. Almost all of them tried to establish a good relationship based on geomechanical parameters. Primary examples are the research done by Ubaldi (1999), Macini, Magagni, Da Dalt, and Valente (2007)."

Jan 1, 2015

The Shortage of Mining and Metallurgical Engineers I N many parts of the Western World attention has recently been drawn to the acute shortage of mining and metallurgical engineers produced by the universities. Naturally, the reasons for this shortage have been discussed, and various remedies for it have been proposed. In this paper, I want to examine some of them. It is now fairly generally ac-cepted among mining men that the easy attractions of modern urban life have left the career of mining in the metaphorical as well as in the literal backwoods. The industry finds it increasingly difficult to recruit adventurous and intelligent young men; for such men now seek their intellectual, if not physical, adventure in more glamorous occupations from a safe social base in suburbia. The salaries, opportunities and security offered by the mining industry do not complete effectively with the rewards offered by other industries and by commerce, taking into account the social disadvantages of a mining life. The excitement and other non-material attractions of mining

Jan 1, 1965

By A. C. Gagnon, H. Saroglou

"The focus of this paper is on the analysis of geometrical discontinuity properties for the rock mass located within an open pit mine located in Western Africa. Discontinuity data were collected using various techniques including oriented core logging, borehole televiewer surveys, surface pit wall mapping and photogrammetry. The geological setting was initially studied prior to the data analysis to produce threedimensional ground models of the regional and mine site geology along with block diagrams illustrating predicted fracture patterns. Stereographic and statistical discontinuity data analysis of the geometrical properties of the rock mass was subsequently performed to identify unique structural domains throughout the open pit area. The discontinuity data collected throughout the studied open pit area were primarily discontinuity orientation, frequency and spacing and the investigation focused on the reasons for observed differences between the various data collection techniques. Stereographic analysis was used to assess the preferred geometry of discontinuities filtered by lithology, data collection technique, borehole, discontinuity type and pit wall (footwall or hanging wall). The observed fracture pattern is explained adequately by the geological setting. The need for accurate ground models for the design of open pit slopes is highlighted.INTRODUCTIONThe Tasiast Mine is an open pit operation located in north-western Mauritania, approximately 300 kilometres north of the capital Nouakchott. The Tasiast mine, which is owned and operated by Kinross Gold Corporation (Kinross), began commercial operations in 2008. The Tasiast mine is located in an area characterized by flat desert terrain within the western reaches of the Sahara Desert region. The current mine site includes mill buildings, shop facilities, waste dumps, tailings facilities and two main open pit operations (Piment and West Branch). The West Branch pit is the focus of this paper. The current open pit plan for West Branch indicates a final pit measuring approximately 2.5 km long by 1.4 km wide and 510 m deep."

Jan 1, 2015

By J. A. C. Ross

Introduction To enlighten those who may be wondering where anyone could find sufficient data to write a paper on underground concrete work, the author would like to explain that, at Copper Mountain, we have found it necessary to line numerous headings with a layer of concrete in order to keep them in a safe and serviceable condition. The majority of these headings are scram drifts and ore-pass raises. This paper will therefore deal, in the main, with the methods of and reasons for placing concrete in these headings. During recent years, radical changes have been made in the methods of mining ore at the Copper Mountain mine. After considerable experimenting, a mining system has been developed making use of diamond drills for primary breaking and transfering such broken ore through scram drifts with slusher hoists. With the advent of scram drifts, it soon became apparent that some substantial means of reinforcement and protection for the scram drifts themselves would be necessary. Since the orebodies in this mine are cut by numerous dykes or faults, and often both, it was anticipated that some means of support would be required where headings necessarily passed through these incompetent zones. Further, as experience was gained, scram drifts were driven into pillars and in close proximity to old workings so as to recover the maximum amount of ore. In such places, the ground is often severely fractured, either as a result of previous mining or from the effect of excessive rock pressures.

Jan 1, 1950

By Arash Habibi

The FMC Westvaco Trona Mine is located near Green River, Wyoming and has an annual production of 4.5 M tons. The underground mine has three active development panels and one longwall panel. The mining horizon is about 500 m below surface and strata liberate methane. Three surface-based blowing fans provide ventilation air. A ventilation survey and subsequent analysis was undertaken and a simulation model developed. Air heating during winter is essential to prevent freezing of pipelines and to lesser degree, for miner comfort. Air at all three intake shafts is heated using gas-fired heat exchangers. A strata heat study was conducted in one of the active panels to determine rock attributes. Tests included in-situ measurements of rock thermal conductivity and geothermal gradient. Continuously methane monitors have also been installed in an active development panel?s return drift. Ventsim ventilation software was used to aid the heat and contaminant simulation study. An exercise was also undertaken to gain some understanding of methane contaminant levels throughout the mine. It was further used to determine an adequate surface intake air heating rate and consequently the minimum natural gas consumption needed for winter intake air heating at the mine.

Aug 1, 2013

By Roger Potvin

Abstract The demand for pure zirconium and titanium metals in Germany increased considerably during the war. Pure zirconium was used in flash bulbs, in vacuum tubes, and in time fuses for bombs, where it has a decided advantage because it gives no gas in burning. Under the form of alloy, it was used with other rare elements for making substitutes for platinum; it was also used as a scavenging agent in high-grade steels. Metallic titanium was mainly used in connection with the manufacturing of special alloys. The authors were sent to Germany by the Department of Reconstruction and have investigated the German process developed for producing these rare metals. They describe the procedure and special equipment used for their commercial production in Germany during the war. General Metallic zirconium and titanium were .produced on a commercial scale in Germany by the thermal reduction, with metallic sodium, of potassium fluozirconate and titanium chloride, respectively, using a mixed potassium and sodium chloride flux. According to the information gathered, the sole German producer of these rare metals in pure form was the Deutsche Gold und Silber Scheideanstalt (commonly called Degussa), at their Werk II, 215 Gutleutstrasse, Frankfurt/Main, which was visited by the authors on September 18th, 1945. As far back as 1934, Degussa was carrying on active research on the manufacture of zirconium, and nearly one ton of the pure metal had been produced before September, 1939. Concurrently, a quite similar process was worked out for the recovery of titanium and it was in commercial operation in the year 1938, during which the production totalled about half a ton (metric). The demand, especially for pure zirconium, increased considerably during the war, attaining a total of about 48 tons during the period October, 1939, to the end of 1944, and reaching a peak of more than 15 tons in 1943. In 1944, the plant was slowed down due to the frequent and disastrous bombing by the Allies, especially in March and September.

Jan 1, 1946

By J. C. Gibson, C. H. Stockwell

"The San Antonio gold mine is at Bissett, Manitoba, on the north shore of Rice lake, 100 miles northeast of Winnipeg. Gold was discovered on the property in 1911, but intensive exploration was not undertaken until 1926. Milling commenced on May 1st, 1932. Total amount of ore milled from that time until the end of 1946 was 1,766,670 tons, having a value of $18,378,317.GENERAL GEOLOGYThe rocks in the vicinity of the mine are Precambrian and include three groups, namely, the Rice Lake series of volcanic and sedimentary rocks, basic and acidic intrusions, and a younger formation of sediments known as the San Antonio formation (Fig. 1). The lower part of the Rice Lake series, consisting of flows of rhyolite, trachyte, and andesite with interstratified beds of agglomerate, occupies an area extending southward from Rice lake. The lake itself and the country to both east and west of its northern end is underlain by the next succeeding beds of the series, which are chiefly tuffs, arkose, and conglomerate, but include a thin band of basalt. Northward from the lake, these are succeeded by the upper beds of the series, first a thin band of basalt and, overlying this, porphyritic andesite flows interlayered with beds of volcanic breccia or agglomerate.The Rice Lake series has been invaded on the east side of the lake by a body of basic rock ranging in composition from gabbro to diorite and quartz diorite, now much altered. This is cut by younger sills and dykes of basic rock, probably diabase, the original texture of which is largely destroyed by alteration. Numerous dykes of feldspar porphyry, quartzfeldspar porphyry, and a few of a rhyolite-like rock, occur south of the lake, but are uncommon to the north. They cut the diabase and older rocks.Extending westward from Rice lake and lying with marked angular unconformity against all of these rocks is the San Antonio formation, consisting of cross-bedded, arkosic quartzite."

Jan 1, 1954

By H. P. Dibbs

An account is given of the application of neutron activation analysis to the rapid, non-destructive determination of copper in minerals, using a 14-MeV neutron source. Elements that interfere in the determination of copper by this method are given, together with the errors in the estimation of copper that result from the presence of varying amounts of these elements. The possible use of a compact "sealed-tube" 14-MeV neutron generator for the field assay of copper in minerals is discussed.

Jan 1, 1970

By J. E. Udd, L. P. Geldart, B. B. Dhar

"Solutions for the stress distributions around simulated underground openings have been limited to calculations of boundary stresses for simple openings in which the boundaries may be expressed in mathematical terms. Studies involving circles, ellipses and ovaloids are re-ported in the literature.The stresses on the boundary of an opening and those at a distance from it in the medium are of concern to the engineer. The former may be related to the greatest concentrations of stresses encountered; the latter have a bearing on the identification of the ""zone of influence"" of the opening.Recent advances, in the form of a derivation for the stresses at a distance from an opening of elliptical shape, together with a solution derived previously for stresses in depth around ovaloidal openings, have been combined with computer programming techniques to provide complete solutions for a wide range of cases and variables. Some typical results which, it is hoped, may have some application to the design of underground openings are given herein."

Jan 1, 1970

By Matthew A. Perras

With growing populations, infrastructure projects are utilizing underground space to expand transportation networks, water supply and sewer disposal systems and hydropower facilities. These new projects require large diameter tunnels to meet the growing demands. As the tunnel diameter increases, not all rock mass properties are scalable and precedent experience becomes less reliable. One such non-scaleable property is lamination thickness. Numerical modelling was conducted to determine the influence of lamination thicknesses on a 16 m diameter tunnel. Five different areas of excavation response were found to exist for laminations ranging between 0.16 to 16 metres in thickness. For this tunnel diameter, critical lamination thicknesses of 6 metre and 1 metre were found to exist. Above 6 metres the excavation response was similar to isotropic models. Below 6 metres the stresses and yield are channeled by the lamination boundaries, increasing plastic deformation. Below 1m multiple lamination units become unstable and the displacements increase significantly and the shape and extent of the yield zone size changes dramatically. The yield zone is controlled by bed deflections and bed parallel shear. As the lamination thickness decreases tensile failure first begins in the haunch area and progressively extends above the crown until a self-limiting plastic yield zone shape is reach at lamination thicknesses below 0.4 metres. Conclusions drawn from observations at the Niagara Tunnel Project are those of the authors.

May 1, 2009