Search Documents

By M. Rafati

In this investigation, the effects of T4 and T6 heat treatments of AZ91 magnesium cast alloy have been studied. The effects of different microstructural details such as morphology, size and distribution of precipitates and their influence on fracture mechanisms were investigated by optical and scanning electron microscopy. The mechanical strength of the alloy after T6 treatment was found to increase in comparison to the T4 treatment, due to the formation of discontinuous precipitates in the grain boundaries. Precipitation in this alloy occurs in two ways: continuous precipitation, which nucleates and grows inside the grains, and discontinuous precipitation, which forms at the grain boundaries. During ageing, the length of the continuous precipitates increases, and, hence, interprecipitate distance decreases. The formation of discontinuous precipitates causes initiation and propagation of cracks at and the weakening of the grain boundaries. This is the principal reason for the reduction of the ultimate tensile strength in T6 heat treatment in comparison to the T4 condition.

Jan 1, 2006

By Alain Simard, Andre Gobeil, Sylvain Lacroix, Maurice Rive, Denis Racicot, Pierre Verpaelst

"The Abitibi volcano-plutonic belt forms the major portion of the Abitibi lithotectonic subprovince in the Superior Province. The Abitibi belt is composed essentially of"" (1) approximately 2.7 Ga old volcanic and sedimentary rocks; and (2) gabbro, tonalite, granodiorite and syenite intrusions occurring in well-defined prekinematic ( synvolcanic ), synkinematic and post-kinematic plutonic suites. Most of these rocks are metamorphosed to greenschist facies. Regional multi-phase deformation affects the volcano-sedimentary rocks. Deformation was initiated as these rocks were formed, and peaked at the end of the Keno ran orogeny with the emplacement of granitic batholiths.There are 145 former and current mines in the Quebec segment of the belt. To date, more than 420 Mt of ore have been extracted yielding 1,600 tonnesof Au, more than4,000 tonnesof Ag,4,400,000 tonnes of Cu and 5,300,000 tonnes of Zn. Mineral production is concentrated in geologic domains that approximately coincide with the boundaries of lithotectonic domains. We have compared the geology and mineral deposits of different domains to illustrate their distinct metallogenic signature. Certain domains are dominantly gold-producing (Cadillac-Malartic, Val-d'Or, Caopatina), others are base-metal producers (Matagami and Normetal), while others produce both gold and base metals ( Rouyn-Noranda, Chibougamau, Casa-Berardi-Joutel).Gold is extracted from quartz-rich vein deposits (for example, Val-d' Or), sulfide-rich veindeposits(Cadillac or Chibougamau) and from volcanogenic massive sulfide deposits ( Rouyn-Noranda). Base metals are generally mined from volcanogenic massive sulfide( RouynNoranda, Matagami, Normetal), although certain vein deposits yield base metals (Chibougamau) . Certain sectors are dominantly zincrich (Matagami, Normetal)."

Jan 1, 1989

By L. Haavanlammi

Iron is a significant component of all copper concentrates leached in the HydroCopperTM process. The metals in the concentrate are leached in a chloride solution by oxidation with cupric ions. Copper enters into the solution as a cuprous chloro¬complex. Iron dissolves at the same time in the ferrous form, but it is immediately oxidized to the ferric state. Oxidation is effected by sparging air or oxygen into the leaching reactors. Because the pH is 1 - 2.5, ferric ion precipitates as akaganeite (T<90°C) or hematite (T> 90°C). Arsenic, antimony and the main part of the bismuth co-precipitate with iron and report to the leach residue. Cupric leaching is faster than iron oxidation; thus, leaching of low-iron concentrates (secondary copper minerals) is quicker than leaching high iron concentrates (chalcopyrite). Pyrite does not dissolve during copper leaching, but is oxidized slowly at higher redox-potentials after the copper has been leached.

Jan 1, 2006

By Olli Aulio, Outokumpu Oy

"GENERALThe Outokumpu Company is today an important European producer of metals from its own mines: copper nickel cobalt, ferro chrome and zinc being the main products. In 1972 about 4 million tons of ore was hoisted from eleven mines.Outokumpu Oy has gained experiences on the various aspects of on line computer control since 1968. This knowledge has been combined to develop a standard computer control package for concentrator control. Before the development of computer control package was started Outokumpu Oy had three large computer control systems. The first system was at the Pyhasalmi Concentrator, thee second at the LokkolaPlant, and the installation of the third system at the Vuonos Concentrator was just started.The characteristics of general computer software packages - both control and executive ones - were thus well-known as well as the practical usage of control theory. Furthermore Outokumpu had developed the Courier analyzer which included a so-called minicomputer. This project had given experience both 1n totally self made real tire executives and in computer hardware and peripheral d=vices. The instrumentation of the Outokumpu concentrators was designed and installed traditionally by the engineers of Outokumpu themselves."

Jan 1, 1973

By J. C. Heaslip

Introduction The greatest single advance in rock drilling practice since the advent of percussion drills was the introduction of tungsten carbide tipped rock drill?bits. The evolution of rock drills has been a long and highly diversified effort which has culminated in the highly refined ?drilling machines we know today, but because of the spectacular possibilities shown by ?detachable bits, and especially those with tungsten carbide inserts, there is little doubt that the cutting face of .the drilling unit has in recent days stolen the spotlight of rock drilling research and commanded the major attention of the rock drilling fraternity. "Solid" Steels Until about twenty years ago, all rock was drilled with a one-piece rod with a bit forged on one end. In the early years of the art of rock drilling, there was tried every conceivable pattern of :bit from the single-edge chisel to elaborate geometric &apos;designs. In the end, it was found that a 4-point bit with two sharpened cutting edges crossing each other at right angles would serve best for most rock drilling requirements. For some years thereafter, the main concern of drill manufacturers was .to obtain the best possible steel for drill rods. This was not accomplished as easily as might be thought. The cutting end had to be such that it could be hardened sufficiently to do its work without premature dulling and yet not so brittle as to shatter under the multiple impacts.

Jan 1, 1951

By J. E. Udd, S. Bharti

"ABSTRACTMonitoring of stability conditions in underground mines permits management to assess the response of the rock mass to mining strategies. Monitoring of movements, if sufficiently early, may also permit operators either to avert potential failures or to develop alternative approaches to extraction.The Falconbridge organization has been a leader both in the uses of rock mass stability monitoring techniques and in the development of instrumentation.In this paper, the authors review the Falconbridge approaches to monitoring, and present case history examples to illustrate the application of the various instruments used.RESUMELa surveillance des conditions de stabilité dans les mines souter-raines permet aux chefs d&apos;enterprises d&apos;évaluer les réactions de la masse rocheuse aux méthodes d&apos;extraction minière. Si le contrôle des mouvements du terrain est effectué assez tot, l&apos;exploitant pourra prendre les mesures qui s&apos;imposent, soit pour éviter les détériorations possibles ou pour mettre au point de nouvelles méthodes d&apos;extraction.Le groupe de la Falconbridge a ére le premier a utiliser des techniques de vérification des conditions de stabilité de la masse rocheuse et a mettre au point l&apos;appareillage requis.Ce document présente une revue des méthodes employées par la Falconbridge pour assurer la surveillance active de la stabilité de la masse rocheuse et illustre au moyen de cas concrets la manière d&apos;utiliser les divers appareils."

Jan 1, 1987

By Maciej Wrobel, Joerg Hammerschmidt, Dana Nurgaliyeva, Alexandros Charitos, Jochen Guentner

"Smelting of copper concentrates in the flash smelter generates a flue dust stream that contains a substantial amount of copper and accumulates more than half of the arsenic input to the smelter. In view of its high copper content flue dust recirculation to the flash smelter is common practice. Globally traded copper concentrates are affected by ever increasing arsenic contents and cause an increasing circulating arsenic load in flash smelter operation. Control of the arsenic level in the smelter slag becomes a challenge. This interaction of arsenic loaded copper feedstock, need for flue dust recirculation and slag quality control call for possibilities to reduce the arsenic load of the recirculated flue dust stream.The technology of partial roasting is known from pre-treatment of copper concentrates before smelting, and gold concentrates before cyanide leaching, to remove the harmful element arsenic. The partial roasting technology can be adapted for use in the purification of the flue dust. A major challenge for flue dust treatment is its extremely fine particle size compared to usual concentrates. For this reason Outotec developed a new process, which allows handling of such fine flue dust. This process solution provides an efficient possibility to reduce the arsenic burden in copper smelter operations.The suggested process aims at reducing the arsenic load to the smelter by treating the flue dust prior to recirculation to the smelter. The presented results are based on test work in the Outotec R&D-centre in Frankfurt. It is possible to remove 80-85% of the contained arsenic and to collect it in an arsenic trioxide residue with a concentration above 90%. The final off gas contains SO2 from decomposition of sulphates that are contained in the flue dust. The off gas stream is relatively small. We assume that it is possible to combine the off gas stream with other smelter process gas streams and to treat it in an existing sulphuric acid plant. Coal is used as fuel and as reductant to reduce pentavalent arsenate to trivalent arsenite. Arsenite can be kept in gas form at temperatures above 450°C. This permits separation of a calcine stream with arsenic levels of 0.2 – 0.3%, which is recirculated to the furnace.Outotec has a wide range of roasting testing facilities from lab-scale to pilot-scale. Outotec has both capability to modify and adapt technology to specific ore or concentrate requirements, but also the necessary infrastructure in its research centers in Frankfurt and Pori to do appropriate validation tests in lab and pilot scale size plants."

Jan 1, 2016

By C. Tissot, R. Palmer

"Due to the low concentrations of gold, direct measurement of gold concentration in ore on belt has not been seriously considered to now. Pre-concentration or sorting strategies have largely consisted of particle sorting based on secondary characteristics such as colour, which can be successful in select cases. CSIRO has produced sample measurement results using gamma activation analysis of ~300 gm samples with accuracies of around 30 ppb at best. With this encouragement, a feasibility study into gold ore measurement on belt for the purpose of sorting pods of gold ore has been undertaken. The study described here included, prototype design options with existing industrial Linacs, extensive Monte Carlo modelling of measurement sensitivity and shielding, further sample measurement, a study of the interaction of target measurement accuracy and sorting efficiency, and a rough estimation of potential economic benefit. The projected model sensitivity of around 0.1-0.15 ppm (1 standard deviation) in 10 seconds for 1 ppm average feed result in good bulk sorting performance and intriguing economic potential.INTRODUCTION Pre-concentration or sorting strategies for gold ores have largely consisted of particle sorting based on secondary characteristics such as colour or density, which can be successful in select cases (Klein, 2010). No method is available to measure gold content for sorting in particles or even in bulk on belt, principally due to the low concentrations of gold present. In fact, in many cases it is difficult to do rapid bulk grade measurements of base metal ores with concentrations many orders of magnitude higher. By a fortunate quirk of nature gold is particularly amenable to gamma activation analysis (GAA). CSIRO has performed extensive work in GAA of samples of crushed ore (Tickner, 2017). This has resulted in the Photon AssayTM technique that is currently being commercialised through the CSIRO spinoff company Chrysos. The technique relies on the recent availability of industrial high intensity X-ray sources such as Linacs which are currently being used in industry for security, medical and sterilisation applications. This development has led to CRC ORE funding a feasibility study to determine whether on-belt measurement of gold concentration is possible at a rate and accuracy sufficient to be useful for bulk sorting, where pods of ore are diverted rather than individual rocks. The study in the first instance is based on Monte Carlo modelling that has successfully predicted the performance of the sample based gold measurements. As well as the measurement feasibility consideration was also given to the likely heterogeneity of gold ores and hence the degree to which useful separation could be achieved. This is then tied to a back of the envelope evaluation of the order of magnitude economics of bulk sorting in an example deposit."

Jan 1, 2017

By R. W. Brigstocke

History The birth of the mining industry of Canada took place about 1670. According to Salone (Salone E., La Colonisation de la Nouvelle France, page 205) the first discovery of ore in the country was made by an iron-master, Monsieur de la Potardiere, near Trois Rivieres, Quebec. Under French rule some prospecting was done; but at this time no one seemed to consider the working of mines practicable. It was not until the time that Begon became Intendant, when the Marquis of Vaudreuil was Governor, that mining was attempted. Begon was a patron of industrial arts and did his best to promote home manufactures. The mining industry was developed under his regime and discoveries of copper and lead ores were made in 1730. About this time the St. Maurice Forges were erected to treat bog-iron ore, and they were in operation for many years. Prior to 1747, iron pans to the value of £21,000 were manufactured, together with bar-iron and plough-shares. About 1769, that is, ten years after the conquest by Wolfe, stoves and other articles, and, later, potash kettles, appeared. What is still more interesting to us-or was, at least, to General Wolfe-is that cannon balls made at the St. Maurice Forges delayed his operations. A map dated 1744, a copy of which appears in the report of the Ontario Bureau of Mines for 1913 (Vol. XIX), indicates the extensiveness of the wanderings of the French and also shows the location of the lead mine on the east shore of Lake Timiskaming. Bog-iron ore was turned into metal, with charcoal for fuel, at Norman-dale, Norfolk county, Ontario, in 1813, and at Clementsport, Nova Scotia, in 1825. In a volume published in 1672, reference is made to the occurrence of coal on the Atlantic seaboard, and in 1677 Monsieur Duchesneau, the Intendant, levied a royalty of twenty sous per ton on all coal taken from Cape Breton.

Jan 1, 1932

By E. Lehtila, J. J. Talja, R. Jahila

Kopar Oy is acknowledged for engineering and manufacturing of robust systems for bulk material handling, especially at power plants and non-ferrous smelters. We have over thirty years of experience with systems specifically designed for hot and abrasive conditions, aiming at low cost of ownership, low operational expenses and high availability. Although Kopar has numerous applications in mechanical conveying, there is an increasing number of pneumatic conveying applications at copper smelters. They relate to conveying of concentrate, and primary and secondary flue dusts. Challenges of pneumatic conveying for concentrate are mechanical and do relate to broad particle size distribution and high abrasivity of the concentrate and the silica. Therefore, special attention shall be paid to system design and ceramically lined bends in the pipeline. Challenges of pneumatic conveying of primary flue dust relate predominantly to material stickiness and poor flowability which are mainly due to fine particle size and formation of sulphates and furthermore, crystalline water. Additional challenges of secondary dust, the white converter dust, are primarily due to the extremely fine 0.1–1.5 µm particle size and problems which come with this. Effect of material characteristics like size distribution, morphology and chemical composition in pneumatic conveying are discussed in detail. INTRODUCTION Fine materials like concentrate, feed mix, flue dusts (from waste heat boiler and electrostatic precipitator) and secondary dusts need to be conveyed at smelters. Both horizontal and vertical conveying and combination of those are used. For the purpose, both mechanical and pneumatic conveying are applied. Most widely used equipment are drag chain conveyors and various combination of pneumatic systems, e.g. air lift, dense-phase and dilute phase pneumatic conveyors. Kopar has 30 years’ experience with multiple material handling systems. Furthermore, acquired companies like Elmomet Oy and SITE Oy (both currently fully merged and integrated into Kopar Oy) have even longer history, especially in pneumatic conveying. It is commonly known that the finer the dust the more difficult it is to be conveyed pneumatically. Sulfates with crystal water makes it all even more difficult, if not ineligible. Challenges related to pneumatic conveying of various fine materials is discussed in detail in the paper.

Jan 1, 2019

By F. E. Lee

The following outline gives a brief account of some of the ways in which microscopy is applied to the problems arising from the various operations of the Tadanac reduction works, at Trail, B. C. The Sullivan ore is a very fine-grained mixture of galena, marmatite, pyrite and pyrrhotite. The separation of minerals associated so intimately is a difficult task and requires careful control. Various oils and reagents are used in the process as developed, and it is essential that the operators have a means of control which shall be rapid, and at the same time, approximately correct. This result is obtained by microscopic analysis in the following manner: The operator places a quantity of the material upon a slide, a drop of water is added, and it is covered with a cover glass. Upon examination with transmitted light, the zinc mineral particles appear reddish, the ordinary gangue colorless, the lead and iron sulphides opaque. This method has proved of great assistance both in the development and in the operation of the present method for concentrating Sullivan ore. The miscroscope has thus become as much a part of the metallurgical equipment as the balance and burette. The microscope used in the laboratory is a Fuess "petrographic" with a specially-made vertical "illuminator" by Bausch & Lomb, with the usual accessories.

Jan 1, 1924

By P. T. O'Kane

The PLATSOL® process, initially developed for the treatment of the NorthMet Cu/Ni/PGM concentrate, has seen over the recent years its applicability extended to include numerous other Cu/Ni concentrates of the same type, as well as other precious metals-containing feedstocks. However, several concentrates were found refractory to the typical PLATSOL® conditions, more particularly so the platinum. Attempts to extend those conditions, such as higher temperatures (250°C), longer retention time, increased oxidation conditions, higher chloride additions, were not successful. Detailed mineralogical investigation of those PLATSOL® leach residues indicated the main refractory mineral to be cooperite (PtS). Further metallurgical investigations showed that a thermal pre-treatment of the concentrate effectively unlocked the refractory platinum minerals for the subsequent leach. Temperatures between 400 and 750°C were tested, with the optimum being found around 650°C. The kinetics of the pre-treatment process were fast, and one hour at temperature proved sufficient. Under those conditions, PLATSOL® extractions were re-established around 95% for both platinum and palladium. From a mineralogical examination of the calcine, it was shown that the effect of the pre-treatment was to transform the cooperite and other refractory sulphides into metallic platinum and alloys, amenable to the PLATSOL®. The implications of the pre¬treatment step for the processing of PGM concentrates arc briefly discussed.

Jan 1, 2004

By D. A. Rhys

"The Red Bluff porphyry is a tabular 2 km long north-west trending Early Jurassic quartz diorite to monzodiorite body that intrudes a folded Triassic greywacke sequence in the lskut River area, northwestern British Columbia. The porphyry is 500 m to 800 m northeast of the Snip orebody, which is a southwest-dipping shear-vein, termed the Twin zone that contains approximately 35 tonnes of gold.The intrusion associated with the mineralization is characterized by 0.3 cm to 4 cm phenocrysts of K-feldspar in a mediumgrained plagioclase porphyritic matrix. It is overprinted by pervasive sericite + quartz ± K-feldspar ± biotite (potassic) alteration characterized by intense stockworking of quartz veins containing magnetite--hematite bands. This assemblage is cut successively by quartz veins with minor iron-oxides and pyrite, and by younger pyrite veins with phyllic envelopes. The system is gold-rich but copper-poor, with typical grades between 0.25 g/t and 0.6 g/t Au, and 0.1% and 0.2% Cu. All styles of alteration and veining have similar abundances of these metals. Where southwest- and north-east dipping shear zones are developed in the porphyry, veins of all types are sheeted and foliation parallel. These sheeted zones are interpreted to be syntectonic. Asymmetric phenocrysts, folded veins and oblique foliations developed in the 130 haulageway of the Snip mine imply oblique normally-directed shear on the southwest-dipping foliation.The adjacent Twin zone is a high-grade auriferous shear-vein system that is internally banded with: (1) carbonate-chlorite-biotite veins, with textures indicating formation at least partially by wallrock replacement, and (2) dilatant quartz-sulphide veins. Veins commonly have potassic alteration envelopes that contain biotite ± calcite ± K-feldspar. The zone is highly deformed and schistose, with numerous kinematic indicators including shear bands, asymmetric folds, rotated porphyroclasts and oblique foliations that indicate a normally-directed shear sense which is parallel to that indicated by fabrics within the porphyry.Precious and base metal veins within 2 km or 3 km of the Red Bluff porphyry are zoned. Veins and shear-veins proximal to the intrusion, such as the Twin zone, are typically enriched in gold, copper and molybdenum, and have potassic alteration envelopes dominated by biotite. Distal veins usually contain relatively abundant zinc and lead and have sericitic alteration envelopes. Structures of both types have an Early Jurassic galena Pb-Pb isotope signature.The similarities in structural fabrics and alteration histories in both the Twin zone and the porphyry, the zoning of the vein systems in the area, and the apparently concordant Early Jurassic zircon U-Pb age from the porphyry and galena Pb-Pb dates from the Twin zone and surrounding vein systems suggest that intrusion, semi-brittle deformation and a large mineralizing hydrothermal system were closely related temporally and genetically."

Jan 1, 1995

By A. Bamber

Canadian leadership in a global mining context will depend not only on entrepreneurship and best practice but also on technological innovation. This paper argues for more ambition and commitment to R&D for technological innovation in Canadian mining. It focuses on underground hardrock mining, where past R&D initiatives have simply not stood the test of time, and it is important to examine why. Concerns arise because industry’s commitment to R&D has not been sustained over time. Innovation through exploration, processing, and environmental technologies has been more significant. Meanwhile, R&D capacity and synergies in government institutions and universities have not been exploited. There is a need for more commitment, coordination, and collaboration by industry, governments, and universities. This paper examines some corporate models that have achieved sustainable innovation, along with some that have not. A strategy for innovation is discussed that relates to culture, commitment, coordination, and collaboration.

Jan 1, 2005

By Craig Haase

A. Introduction

Jan 1, 2003

By J. J. Denny

IN a preliminary paper (1) it was shown that the addition of small quantities of metallic aluminium powder almost completely inhibited the solubility of siliceous material in the beaker. Six rabbits exposed to quartz dust for six months all showed well developed silicosis. Seven rabbits exposed to quartz dust plus 1 per cent metallic aluminium powder for the same period did not develop silicosis. At that time, we were not in a position to state either the manner in which metallic aluminium reduced the solubility of siliceous material, or, from the animal experiments, whether the aluminium was acting locally or systemically, or for what period after the cessation of dusting it would continue to act. This paper reports the further progress of this investigation. CHEMICAL EXPERIMENTATION The technical details pertaining to the various substances used in the experiments are given in an appendix which is on deposit with the American Documentation Institute, Washington, D.C. For lack of space, it is not printed here. The term &apos;solubility&apos; is used to indicate the concentration of silica in the solution under the conditions as noted, determined colorimetrically (2), and expressed as parts per million (p.p.m.). The term &apos;reduction in solubility&apos; indicates the difference between the solubility of the .silica in the presence of the aluminium powder and its solubility in the absence of aluminium powder. It will be noted that the solubility figures for different samples of quartz with no added aluminium vary considerably. The figures do not refer to an equilibrium solubility of silica but to the actual amount of silica dissolved from a given sample in a given time at a given temperature. In view of the fact that quartz dissolves extremely slowly, it is evident that the actual figures in any case will depend upon the surface exposed, i.e., fineness of grinding of the different samples.

Jan 1, 1939

By Marco Quirion

The Daniel-Johnson dam, formerly named Manicouagan-5 (Manic-5), is located 800 km northeast of Montreal (Quebec) in Canada. This is the largest multiple-arch concrete dam in the world consisting in 13 arches and 14 buttresses. Since its construction in 1969, various type of cracks have appeared on both downstream and upstream faces of almost all the arches of this concrete dam. As a part of the Daniel- Johnson’s dam safety assessment program, Hydro-Québec is currently performing structural analysis of the dam with advanced numerical models to better understand and predict the dam behaviour. Because the buttresses transmit all the arch loads to the rock mass, determination of the properties of the dam foundation should not be neglected in dam global safety analysis and also to insure that reliable input parameters are used in the dam numerical simulations. This paper summarizes the past and the more recent investigations of this foundation used to assess its safety and stability. Moreover, the use of rock mass classification to estimate the deformation modulus, based on empirical equations, gives values in the range of 30 to 40 GPa that are higher than expected values. Using those values in the numerical simulations for dam structural analysis gives an excellent correlation with displacements monitoring of the buttresses.

Jan 1, 2015

By Chenming Liu, Xiao Lin, Bo Wang, Hongbin Cao, Xingang Li

Over 2 million tons of NH3-N were discharged in China per year recently, rare earth industry contributed 7.03% of NH3-N pollutant from industrial wastewater in 2007. Wastewater containing NH3-N and heavy metals mainly produced in RE extraction saponificated with ammonia and precipitated by ammonia bicarbonate. Generally, 1 ton REO cost 0.6-1.2 ton ammonia for extraction and 1.6 ton ammonia bicarbonate for precipitation, and produce 35-100 ton wastewater. Processes, like Na-saponificated, Ca-saponificated and Non-saponificated technique, are widely studied to reduce the adverse environmental effect of RE industry, while traditional processes still have advantage in production cost, process stability and product quality. In this study, a novel process that combines distillation and air-stripping is developed. NH3-N is removed and recovered based on relative volatility difference of NH3 and H2O. Phase equilibrium, heat equilibrium are calculated to determine process parameters. Hydrodynamic performance like flow field distribution is also simulated. Then, design parameters for distillation trays or structured packing are determined based on calculations and simulations. Besides, the phase diagram of (NH4)2SO4-NH4Cl-H2O in 30°C - 100°C, the typical salts composition of nonferrous wastewater, is studied to ensure commercial plants’ continuous operation. Ammonia removal tower (ART) with different high efficient column internals is designed to fit RE wastewater treatment requirement. The novel process has been commercialized in RE industry in Jiangxi, China. The commercial project operation results show the novel process reached a nearly zero-emission with >99.5% NH3-N was removed and then recovered as ammonia. Combined the novel process, the traditional REO separation process using ammonia and ammonia bicarbonate could achieve NH3-N reuse and the effluent quality meets the discharge standards.

Jan 1, 2016

By J. W. Gregg, P. M. Dranchuk, D. L. Flock

"From preliminary investigations it has been observed that although evaporation losses may be estimated by comparing single values of certain physical properties of crude oils and their evaporation residues, such techniques possess little accuracy unless both the evaporation process and the variation of the property as a function of the process are completely known. The accuracy of estimation may be increased somewhat through the comparison of property mid-per-cent curves. Further increases in accuracy are possible if bottoms yield •curves rather than mid-percent curves are used. The use of both the mid-percent and bottoms yield curves however involves a prohibitive amount of effort in most cases. Examinations of distillation bottoms from Hempel type distillations carried to end points just short of the cracking point have indicated that these bottoms are not appreciably affected by the evaporation process. It was further observed that bottoms of identical API gravity, obtained from a crude oil and its evaporation residues behave as if they were pure components which were unaffected by evaporation. Based on these observations Hempel distillation bottoms of equal API gravity were obtained for a crude oil and its various evaporation residues from API gravity bottoms yield curves. The volume percent of these bottoms in the crude oil and its residues were used to calculate the evaporation losses suffered by the crude in order to yield the various residues. The results indicate that, although further refinements in technique are required, it is possible to calculate evaporation losses with an accept-able degree of accuracy through the use of this method."

Jan 1, 1960

By B. R. MacKay

Introduction During the past six seasons the writer has been engaged in semi-detailed investigations on the coal areas lying along the front of the Rocky mountains between the Brazeau river and the Smoky River Coal Reserve (see Map, Figure 1). The purpose of this paper is to present some observations pertaining to the stratigraphy and structure of the district, touching especially upon the lithological units into which the Lower Cretaceous sediments have been divided, the thicknesses of the formations at different localities, the number, thicknesses and horizons of the principal coal seams, and the structural conditions which exist in the various fields.

Jan 1, 1930