Search Documents

Several inorganic reagents and organic polymers were tested as depressants in the single mineral flotation of ultrafine iron oxide and hydroxylapatite with Dowfroth 250 as a frother. It was observed that the inorganic reagents and the low molecular weight polymers generally caused dispersion of the ultrafine particles, and consequently their recovery into froth products more or less equaled the recovery of water. On the other hand, the high molecular weight polymers caused different degrees of flocculation of the ultrafine particles, and their recoveries were much lower than the recovery of water. These observations pointed to a need to re-define flotation depressants in fine particle flotation. The traditional definition of a flotation depressant, i.e., to make particle surfaces hydrophilic by forming a hydrophilic film and/or by removing collector and activator coatings, is sufficient for relatively coarse particles. However, to prevent fine and ultrafine particles from floating, a successful depressant should not only make the particles hydrophilic, but also enlarge the particle sizes so that they do not enter the froth product by mechanical entrainment. Polymeric depressants are ideal for these purposes. The different schemes to use polymeric depressants in the selective flotation of fine and ultrafine particles were discussed These schemes involve the integration of the polymeric depressants into other size enlargement processes such as shear flocculation, oil agglomeration, etc., for hydrophobic particles.

Jan 1, 2004

The following guidelines have been recommended by the Diamond Exploration Best Practices Committee established by the Canadian Institute of Mining, Metallurgy and Petroleum. These guidelines are applicable to public companies and their consultants reporting diamond exploration results. In respect of these guidelines, Diamond Exploration Results are results derived from the initial activities undertaken to investigate a diamond bearing prospect or deposit, to generate tonnage, grade and value estimates that cannot be classified as a Mineral Resource or Mineral Reserve. They do not address the earlier stage reporting of geophysical, geochemical or kimberlite indicator mineral results. Public reports of Diamond Exploration Results relating to mineralization not classified as Mineral Resource or Mineral Reserve must address the confidence limits of the result and contain sufficient information to allow a considered and balanced judgement of the significance of the results. The objective of these guidelines is to assist public companies and consultants in making appropriate disclosure of diamond exploration results by reporting in a manner which is: ??Uniform within the diamond exploration industry; ??Consistent with reporting from other industry sectors; ??Comprehensive; ??Unambiguous. The guidelines are not prescriptive. Materiality is the overriding principle that determines the information that should be disclosed. However, where a company or consultant deviates from the guidelines, the disclosure or technical report should state the extent to which the guidelines have not been followed, and the reasons for the deviation. The guidelines do not in any way replace jurisdictional reporting requirements (For example, the requirement for Canadian reporting issuers to comply with Canadian Securities Administrators National Instrument 43-101 by having technical disclosure endorsed by a Qualified Person as defined in that legislation).

May 1, 2003

By Dean Millar

Clean, green, cheap compressed air can be produced efficiently and renewably by modernization of a 19th century technology ?The hydraulic air compressor has no moving parts ?After commissioning, the Ragged Chutes HAC operated for 70 years, only being stopped twice for repairs to the intake heads ?Operates using hydropower from Montreal river ?Produced air for ~29 silver mines in Cobalt, 20 km distant

May 1, 2013

By R. J. Balfour, T. L. Papucciyan

"INTRODUCTIONCapital Cost considerations are basic to feasibility in the achievement of success for Mineral Processing Projects as much as or more than in many other industries. Capital cost is an important factor ae it 1R the unit of measurement for process engineering economic decisions. As a result of ever increasing complexity, alternatives of process and remoteness of site, there is an ever increasing emphasis on accurate estimating and the attendant cost control systems in the international market of today for the Mineral Industry where initial plant costs are becoming a more important factor than operating costs. An undervaluation means trouble ahead. An over-cautious assessment may bring an unnecessary abandonment of a project. Consequently, the ultimate cost must be predicted early and accurately and must be controlled to this parameter during the design and construction phases. Cost Est!~ mating is one of a variety of project management tools used to assist in planning and achieving the optimum balance between Quality, Cost and Time, the eternal triangle of evaluation, namely obtaining a project of acceptable quality at minimum cost and on time. In order to attain these established objectives, proper planning, organizing, coordinating, monitoring, adjusting and controlling the design, procurement and construction elements of the project are essential.This project management approach based upon the principle of a Task Force under single management, comprising a complete service organization, requires a substantial number of qualified individuals specialized in their own field and capable of working together as a team to perform their various functions effectively. The Task Force is supported by their chiefs of discipline and performs in accordance with established procedures and standards under the leadership of a Project Manager.General Engineering Company Limited with the backing of the full resources of Surveyer, Nenniger & Chenevert and its total staff of approximately 1,0009 offers the complete project management service to the Mineral Processing Industry of North America and the rest of the world. As mine sites become more remote and difficult of access, the need for an experienced team of specialists who work under the Task Force principle, with well established standards and procedures becomes even more important. Our long history of successful pro1ecta in this field has been our training ground for the fulfillment of this need."

Jan 1, 1972

By K. C. Viveros, R. R. Ambriz, C. García, F. De Villèle, A. Talha, D. Jaramillo

Cold hole expansion on base metal, weld metal and heat affected zone of 6061-T6 aluminum alloy welds was simulated by means of finite element method. Three dimensional compact test models with a previous fatigue crack length with a relation of ??= a/W = 0.3, were used to analyze the hole expansion process. Considering the local mechanical properties for each zone of the welded joint, the optimal expansion degree (1.64 to 2.46 %) was determined. The residual stress field, through thickness, after the expansion process in all welding zones, were correlated with the crack opening displacement obtained by finite element analysis. It was observed, that compressive residual stress fields for a post-expansion, in different crack lengths, provided a crack closure mechanism for base metal, weld metal and heat affected zone. Contrary, the crack remained open when residual stresses are positive. The results are given as tangential stresses versus distance from the edge of the cold expansion and crack opening displacement as a function of applied load.

Jan 1, 2014

Background Chronology 2008 Positions May 8, 2010 Summit Going Forward Say one thing and do another ??Genuine passion to see our customers succeed?, ?A passion for exceeding our customer?s expectations? Self serving actions to gain competitive advantage at the expense of the customer No single supplier or technology can manage the overall mine and its integrated operation - April 2005: Informal meeting at Toronto CIM 2004 -Unanimous interest - July 2005: Formal Calgary Meeting, developed: - Scope and vision statement , - OEM/OTM communication plan, - industry communication plan - Aug?Nov 2005: Aligned with SMART - Nov 2005?May 2006: Direct OEM, OTM communication - May ?Sept 2006: Developed baseline standards - Sept -April 2007: Developed SMART document - Sept 2007: Document distribution and request OEM OTM response - Jan ?May 2008: Acquired OEM OTM feedback and positions May 2008: Results presented to SMART and discussions on next steps

May 1, 2010

By J. Olaf Sund

"The New Brunswick gypsum and an-hydrite deposits make up part of the Windsor group in the Upper Mississippian. The present deposits were formed by surface hydration of the underlying anhydrite beds. The sub-hydrate, hydrate, and di-hydrate stages of gypsum are formed from the anhydrite by this hydration. The anhydrite was precipitated from sea water in embayments that were separated from the sea by a reef or bay-mouth bar. The anhydrite is the original form of the calcium sulphate precipitate.One gypsum deposit near Plaster Rock in northern New Brunswick was precipitated from sea water directly as gypsum, which is its present form."

Jan 1, 1960

By S. Power Warren

Introduction It is generally conceded by flotation men that the condition at the surface of a particle of mineral or gangue is the most important factor controlling its behaviour in a flotation cell. Much research work has been devoted to the study of the forces that are active at the surface of the particle and of the effect of the surrounding solution upon these forces. Study of the relationship between mineral or gangue particles and gas bubbles indicates that, in the main at least, flotation is a physical phenomenon. The important factor, that of mineral-gas-bubble attachment, is unquestionably physical; however, modifications may be effected by chemical means, whereby the nature either of the surface of the particle or of the surrounding solution may be changed. For example, the coating of lead sulphide that forms on lead-carbonate ore particles when sodium sulphide is added greatly aids the flotation of the carbonate particles. Without going into the question as to why, under certain surface conditions, mineral particles will attach themselves to gas bubbles whereas under other conditions they will remain unaffected, it may be stated that there are three general conditions in a flotation pulp which control the attachment of the particle and the gas bubble.

Jan 1, 1933

By B. Morrison

"The Kiruna Electric System is a recently developed inclined ore haul age system for underground mining operations. Although an initial investigation was carried out at the Swedish underground iron ore mine LKAB almost three decades ago, it was not until 1981 that the resources of LKAB, ASEA and Kiruna Truck AB were combined to investigate, and subsequently develop an ""all- electric truck"" for the mining industry.It has long been appreciated, that major economical advantages could be realized by a mining operation through an extension of the cost-effective life of the existing ore hoisting system by the use of ramps to haul ore up to the main haulage level. Diesel truck s have been used and are being used for ramp haulage. Their use however, is limited due to ventilation and operating costs restraints.There are numerous instances of orebodies, located within a couple of hundred metre s of surface, or below an existing hoisting facility, being developed by ramp access while the shaft is being sunk. Development of an orebody via ramp access has many advantages to a mining operation where mechanized mining is to be practiced. These advantages are both practical and economical; generally falling within the over-all umbrella of the phrase ""cash flow"" mining.The decision to sink a shaft is a major committment by any mining company, regardless of size and financial reserves. Extensive diamond drilling, both shallow and deep must be carried out before a decision can be executed. This constitutes a major financial expenditure over an extended period of time.The decision to sink a shaft must be weighed against the reliability of geological interpretation of the deep diamond drilling results, the stability of the mineral market and potential fluctuation in ore prices and interest rates."

Jan 1, 1989

By B. Yu, Y. O. Oyediran, M. Robart

"This paper presents the latest flotation development testwork conducted in 2015 on the ‘B Zone’ samples from the Strange Lake Alkalic Complex (SLAC). Since the discovery by Iron Ore Company of Canada (IOC), metallurgical development has been under taken by a number of mining companies targeting various value metals, including yttrium, zirconium, niobium, and rare earths.Most recent, Quest Rare Minerals Ltd. (Quest) completed a Pre-Feasibility Study (PFS) in 2013 where the flowsheet was relatively complex and led Quest to explore alternative options. In 2014, the PFS flowsheet was simplified and one of the features introduced was pre-concentration by rougher flotation. The combined rougher flotation concentrate and slimes successfully recovered >90% TREE in 60% mass thus reducing capital cost and technical risks of the downstream hydrometallurgical processes. The latest flotation development testwork focused on achieving a pre-concentrate in which >80% TREE are recovered in 20% mass. Two separate reagent schemes, based on an ester phosphate collector (Clariant 1682) and a benzoylhydroxamic acid collector (Florrea 7510), were developed. Parameters evaluated in the development testwork included desliming, secondary yttrium and zircon collectors, depressants, temperature, conditioning temperature, time, and density, pH, sodium silicate type, cleaning, and flowsheet configuration. Both developed reagent schemes achieved the targeted metallurgy.INTRODUCTIONThe Strange Lake Alkalic Complex (SLAC) was discovered after geological survey and mapping studies by Geological Survey of Canada and Newfoundland and Labrador Department of Natural Resources between 1967 and 1980. Subsequent exploratory drilling programs by Iron Ore Company (IOC) in the 1980s found that the REE and high field strength element (HFSE) mineralization were within the central region of the SLAC which was named A Zone by IOC and later renamed Main Zone by Quest Rare Minerals Ltd. (Quest). Additional exploratory drilling outside the Main Zone by IOC and later by Quest, led to the discovery of B Zone, which was recognized as the most significant deposit of rare earth elements, yttrium, and zirconium in the SLAC. The B Zone Indicated Resources are estimated at 278.13 Mt at 0.93% total rare earth oxide (TREO) and Inferred Mineral Resources are estimated at 214.35 Mt at 0.85% TREO (Oyediran et al., 2014)."

Jan 1, 2016

By Peter Radziszewski

"Comminition process costs, which typically represent an important contribution to mining operating costs, can themselves be divided roughly between energy and liner /charge wear. As such, developing the ability of predicting mill wear will allow a more accurate estimation of wear costs and therefore their control. In this paper and based on the possibility of estimating energy dissipated in impact and abrasion by using a discrete element charge motion model for mill charge motion simulation, media wear will be investigated principally as a function of three wear mechanisms : impact, abrasion and corrosion. Experimental results will be used to identify a total media wear model. Model results will be compared with real mill data from three operating Australian mines. These preliminary results show for the cases tested that the overall average error, as compared with the observed cases, is 0 % with a standard deviation of 66.1 %. Results from the Bond abrasion index tests, for the same cases investigated, give an overall error of 73 % and a standard deviation of 192.5 %. Further work is in progress to improve test procedure, validity and confidence.INTRODUCTIONComminition process costs, which typically represent an important contribution to mining operating costs, can themselves be divided roughly between energy and line / charge wear. In Greenfield situations where the estimation of operating costs is critical in determining project feasibility, the level of confidence in such estimates becomes quite important. With regards to media wear, the Bond abrasion test currently serves as the standard media wear prediction device. However, as shown [l, 21 test results once compared with actual wear rates can vary greatly. Figure 1 shows test results as compared with 15 cases. Average error over this data is 73 % with a standard deviation of 192.5 %. As such, developing the ability of more accurately predicting mill wear will allow greater confidence in wear cost estimation and therefore their control."

Jan 1, 2001

By M. Tardif, F. L. -Lavoie, M. Ruel

"In mineral processing, it is often very difficult to reliably measure several key operation variables. The harsh environment and high temperature encountered in pyrometallurgy processes lead to some difficulties when selecting the instruments, valves and actuators. If an important variable cannot be measured or manipulated adequately, controlling it can really become a big challenge. Sometimes, it is simply impossible to find the perfect equipment for the task. To help overcome these difficulties, a different approach is required. This approach will not correct the inherent problems related to the instruments and valves, but will cope with these problems. This article will demonstrate how modern process control techniques can be used to solve complex problems while remaining easy to implement. In this article we will described how soft sensors and multivariable fuzzy logic control were implemented at Koniambo Nickel to stabilize the furnace feed and allow for safe and reliable operation of an 80 MW DC arc furnace.INTRODUCTION Process Overview The process plant at Koniambo Nickel SAS is located in the North Province of New Caledonia, 310 km north of Noumea. The nickel-bearing ore is mined in the nearby Koniambo massif. After being screened and crushed, the ore is transported to the processing plant using a 12 km conveyor. After stacking in two blending piles, the ore, containing 2.3% nickel, is fed to the processing plant where it will go through the NST process (Nickel Smelting Technology) before being sent to refining and shotting. This article will focus on the improvement to control of the NST processes. The first steps of this process consist of milling the ore and removing all moisture through calcining (Figure 1)."

Jan 1, 2017

By A. F. Banfield

"IntroductionELEMENTAL sulphur occurs in three types of deposits: in salt domes in the Gulf Coast region of the United States and Mexico, from which over 90 per cent of world native-sulphur production is obtained; in sedimentary deposits such as those in Sicily, which are thought by some authorities to contain the largest world reserves of elemental sulphur; and as surface deposits, associated now or in the past with some phase of vulcanism, the type which bas the greatest world-wide distribution.Deposits of the volcanic type are the subject of this paper.From antiquity until the successful development of the sulphur-bearing salt domes at the beginning of this century, important sulphur production for local needs was obtained from volcanic deposits in many parts of the world. Due to technical and economic factors, however, producers could not compete in price with sulphur from salt domes. •The result has been that, except in Japan and Chile, little sulphur was produced from volcanic deposits from about 1910 until the start of the Korean war in 1950. Shortly after the outbreak of the Korean war, an acute world sulphur shortage developed and prices skyrocketed in many countries up to several hundred dollars a ton. Interest in volcanic deposits was renewed and exploitation of many was undertaken. Few of these operations have been successful, mostly due to inability of management to solve technical problems.While important volcanic deposits of elemental sulphur have not been reported ( 1) in Canada, and it is doubtful that any will be found, data presented in this paper may be of interest to students of ore genesis.This paper is based on field examination of numerous deposits of the volcanic type in North and South America."

Jan 1, 1954

By Jeff Stufsky

Debt Financing ?Broad Market Overview ? Recovering due to factors including: ? Increased trust in the system ? Enhanced capitalization of financial institutions ? The need to deploy capital for profit ? Competition: ? Investment-grade bond volumes increasing dramatically, and starting to pressure banks to compete with new capital ? Term Loan B financing from insurance companies and related institutions is returning, also pressuring banks to lend ? Local country financial institution capacity in Latin America has materially increased ? Results: ? Loan capacity increasing generally across instruments, regions, and sectors ? Financial institutions/banks starting again to seek yield as pricing competition heats up ? Tenors increasing with pricing coming down more slowly Underwriting is back in play

May 1, 2010

Palabora Mining Company (PMC) processes a multi-component ore body using a circuit consisting of two AG mills in parallel, closed with vibrating double deck screens and hydrocyclones. The bottom screen undersize feeds the hydrocyclones, but the screen oversize products can be treated in a variety of ways. The top deck screen pebbles can be crushed and then combined with the bottom deck oversize and recycled to the AG mill. Alternatively both the top and bottom deck screen oversize can by-pass the recycle crusher and be recycled directly to the mill. A full tap-off is a configuration when both the top and bottom deck screen oversize streams are stockpiled. The other configuration is when the bottom deck screen oversize is recycled to the mill while the top deck screen oversize is stockpiled - termed partial tap-off. This article reports the findings from the surveys performed to evaluate the performance of the PMC auto mill circuit when operated under the four different configurations discussed. Ore characterisation tests were performed to assess the deportment of the key ore components for the different configuration.

Jan 1, 2012

By John G. Peacey, Leoncio Sevilla G., Ford. Kevan J. R., Erling Villalobos C.

"Kinross Gold Corporation’s Mantos de Oro (MDO) gold/silver mine in northern Chile currently processes 15,000 tpd of oxide ores through a mill, whole ore cyanide leach plant followed by a Merrill-Crowe refinery. With the expected depletion of these oxide ores in a few years a new sulphide mineral deposit, Ladera-Farellón has been identified to potentially replace existing ore reserves. The deposit contains approximately 0.5g/t Au, 6g/t Ag and 0.5% Cu. The principal sulphide mineral in the deposit is enargite (Cu3AsS4) which hosts the majority of gold and silver and the copper. Direct cyanidation testwork has shown the sulphide mineral is refractory with a low gold recovery of 36% and silver recovery of 45%. Oxidation of the sulphides is required to liberate gold and silver and allow recovery of copper as an important pay-metal. Therefore, at MDO a new metallurgical process route with oxidation as a pretreatment step is required for viable treatment of such new sulphide mineralized material with acceptable recoveries of pay-metals.Analysis of flowsheet options was completed based on bench-scale and pilot scale metallurgical testwork as well as with reference to existing studies and operations. The process options investigated assume concentration of sulphides by flotation, followed by either pressure oxidation, bacteriological oxidation or roasting. Preliminary evaluation of flowsheet options focused on process risk, operability, technology availability and the economics of the project with emphasis on use of the existing metallurgical plant to reduce capital cost. Operating costs for each process option were also included in the relative analysis.The challenges of treatment of MDO sulphides, principally enargite and pyrite for recovery of gold, silver and copper center on fixation of arsenic and sulphur capture with environmentally acceptable disposal of residue tailings. This environmental focus was included in the process option selection and comparative analysis.This paper presents a review of the process options considered and highlights comparative advantages/disadvantages of each process with associated environmental issues. Preliminary conclusions are drawn on roasting as a potentially favorable process option for the treatment of MDO sulphides."

Jan 1, 2009

By E. Ghali, A. D. Bas

"Treatment of oxide, e.g. roasted gold ores has received relatively less attention than sulphidic ones and recently, handling of oxide gold ores is becoming essential. In this study, the influence of roasted gold ore (RGO) slurry (at 35% solid ratio) on the electrochemical dissolution of gold has been examined using pure gold and iron oxide minerals (hematite, maghemite, and magnetite) as disc electrodes by zeroresistance ammeter mode either in one or two separate containers. The presence of slurry decreased galvanic currents, i.e. corrosion rates due to the release and increase in the amount of soluble and/or insoluble species that could retard further the anodic behaviour of gold. Higher galvanic currents were observed in two separate containers than that in one container indicating the primary importance of galvanic interactions. SEM-EDS results observed iron hydro/oxide coatings on gold surface in case of magnetite test. However, in case of RGO electrode it is not a perfect passivation, although somewhat decreasing trend was observed on gold dissolution. These findings have revealed that passivation is not only a laboratory phenomenon, but also it could be responsible for the slowdown of gold dissolution in industrial practice.INTRODUCTIONThe cyanidation of gold is an electrochemical corrosion process thus; the dissolution of gold can readily be studied by electrochemical techniques. The outcome/summary of previous electrochemical studies of gold leaching can partially be summarized as follows: Filmer (1982) and Lorenzen and van Deventer (1992) reported the negative effect of pyrite and pyrrhotite on gold leaching due to the galvanic interactions; Aghamirian and Yen (2005) studied gold galvanic corrosion in presence of sulphide mineral electrodes only in one cell using zero-resistance ammeter (ZRA) mode; Dai and Jeffrey (2006) discussed, individually, the anodic and cathodic behaviours between gold and sulphide minerals, and Azizi et al. (2010, 2011) used a bed reactor to examine the influence of sulphide minerals on gold dissolution in one and two separate cells. Accordingly, a slowdown in gold leaching has generally been attributed to the passivation phenomenon, although the indication of this phenomenon is still an undergoing debate. For instance, Mrkusic and Paynter (1970) identified the passivation as the film formation of dissolved species from calcine, Crundwell (2014) explained passivation, in the case of corrosion of metals, as the formation of a layer which is composed of a new chemical species on the mineral surface and this layer inhibits or blocks further reactions. He suggested that passivation is related to the oxidation of the metal, and the formation of a passive layer that retards the rate of dissolution by several orders of magnitude. Consequently, galvanic interactions, passivation phenomena, or combinations of them are considered significant electrochemical factors affecting gold dissolution (van Deventer, Reuter, Lorenzen, & Hoff, 1990; Azizi, Petre, & Larachi, 2012). It is important to note that generalizing the influence of a mineral/metal on gold dissolution may not be correct in all cases, since contrary behaviours/results (for pyrite) have been observed (Aghamirian & Yen, 2005). Therefore, electrochemical study of gold is still a subject of research and need to be examined further in detail."

Jan 1, 2016

By R. Stauffer, S. Lindsay

"Sherritt Gordon Mines Limited utilizes pressure hydro-metallurgical techniques to recover nickel, copper and cobalt from su1phidic concentrates, mattes and various other metal-bearing materials.A brief description of the nickel refinery operation is given. In the nickel refinery process, an ammonia pressure leach is employed to treat the feed materials to dissolve the non-ferrous metals as their respective ammine complexes. The resulting leach solution goes through a series of steps which removes copper as copper sulphide and further purifies the solution prior to nickel precipitation by hydrogen reduction. The reduction end solution, containing the cobalt which was originally present in the leach solution as well as residual nickel, is treated with hydrogen sulphide. The resulting nickel-cobalt sulphide precipitate feeds the soluble cobaltic ammine process, which separates the nickel and cobalt and recovers the cobalt as a pure powder.A detailed description of the cobalt recovery process is given. Included are the various steps, comprising: acid leaching of the mixed sulphides, solution purification, ammine complex formation and cobaltous oxidation, two-stage nickel precipitation, cobalt conversion and reduction. A brief description of cobalt powder handling is included, along with typical physical properties and chemical analyses of the cobalt product. In general, the purpose of this paper is to describe the present plant practices employed in the recovery of cobalt as a by-product of the nickel refinery operations."

Jan 1, 1967

By M. El Tokhi, H. Arman, B. M. Amin

"This paper aims to overview some mechanical and physical features of the gabbroic rocks. The study has two phases: filed study/in-situ measurements and laboratory work. During the field studies, rock block samples were collected from different locations of the study area to represent the different types of the gabbroic rocks. Either core or rock samples for various tests were prepared from rock samples taken to the laboratory. The unconfined compressive strength (UCS), indirect tensile strength (ITS), point load index (PLI), Schmidth hammer rebound value (SHV), slake durability index (SDI), sonic velocity (SV) and unit weight (UW) test were carried out either on the selected rock block samples or core samples.INTRODUCTIONThe geology of the United Arab Emirates (UAE) has been divided into three major rock units (Lippard et al., 1986); an autochthonous succession, allochthonous units composed mainly of Mesozoic rocks and include the Sumeini Group (concomittent slope sediments), Hawasina Complex (basinal sediments) and the Semail ophiolite nappe (massive slice of former oceanic crust), that were emplaced as a series of thrust nappe in the Late Cretaceous and Neo-autochthonous sequence of Maastrichtian and Lower Tertiary sediments.The Semail Ophiolite (600 km long and up to 150 km wide) is thought by some authors (Glennie et al., 1990) to have been generated along a subduction related back-arc spreading axis during the Cenomanian-Turonian and was obducted onto the Arabian continental margin during the Campanian. Others, however, consider it to represent a primitive arc-spreading center related to oblique subduction Lippard et al., 1986). The Ophiolitic rocks in the study area comprise mantle and crustal sequences. The mantle peridotite and crustal gabbros are the dominant rock types of the exposed Semail Ophiolite north of the Hatta zone. This paper is only concentrated on the gabbroic rocks."

Jan 1, 2015

The Red Lake greenstone belt is an irregular mass of lavas sedimentary rocks and intrusives which is approxiately 35 miles long 18 miles wide and 7 miles deep. Basaltic volcamcs are the oldest rocks w1thm the belt. They are believed to have been laid down on an ancient crust which is at least 3 billion (3 x 109) years old and was composed partly of sediments. The basaltic rocks are overlain by acid volcanics and sedimentary rocks which have been complexly folded and are preserved as a down-folded remnant of younger rocks within the older crust. The volcanics and sedimentary rocks of the greenstone belt have been cut by intrusives with a wide range of composition. The emplacement of the intrusives and the accompanying regional metamorph-ism which terminated the orogenic activity in this area are believed to have occurred approximately 2.4 billion years ago. The basalts and many of the basic and ultrabasic intrusives undoubtedly had their source in the sub-crust or mantle. At least some of the granitic intrusives are believed to have had

Jan 1, 1965