Search Documents

By S. Averill, B. Schreiner, V. Sopuck

The La Ronge. Kisseynew, Glennie Lake and Flin Flon domains. the main focu for gold exploration in the southeast part of the Saskatchewan Shield, were subject to continental glacial ice advances from the northeast during the Quaternary. Based on forty-four auger hole along with surficial mapping, the general Quaternary stratigraphy in this area is observed to be composed of a lower till unit , an overlying stratified unit of glaciofluvial sand and gravel and/or a glaciolacustrine silt-clay unit. an upper till. and an upper tratified unit. The lower till is commonly found throughout the geological domains except where it has been eroded in glaciofluvial or fluvial channels. Glacial Lake Agassiz fo rmerly covered most of these prospective domains. The lacustrine deposits associated with the lake impede surficial geochemical surveys including soil. lake sediment. and biogeochemical surveys. The approximate extent of clay cover can be predicted from beach elevations. For instance. in the Waddy Lake area. clay i not known to occur above about 1,400 feet (425 m) elevation. Exploration techniques are hampered by clay in at least one third of the volcanic belt. Thi s influence is indicated by the fact that nearly all gold prospect found to date are located above 1,400 feet (425 m) while the area of clay cover is vi rtually unexplored. The upper till i related to a minor ice readvance. This till is the medium often sampled during soil surveys in the area . lts value as a geochemical ampling medium is dependent on the extent of erosional contact with bedrock highs on the lower till. Those areas which are relatively free of lacustrine and fluvial deposits are those where surface geochemical methods work best. In the Waddy Lake volcanic belt approximately 25-50% of the area may be suitable for surficial surveys. The area of the Star Lake prospect occurs above the 1,500 foot (460 m) elevation and was not covered by Lake Agas iz. The effectivene of till sampling as a surface sampling medium was tested in those areas above the clay level. Till orientat ion surveys were carried out at the Star Lake property and the Tower Lake prospect (Waddy Lake area) within the La Ronge Domain . Gold grain counts and analy es of heavy mineral concent rate from 7 kg surface ti ll samples were used to delineate dispersion trains down-ice from mineralization. In addition, the clay fraction and a 30 g (-80 mesh) subsample from the same till sample, were analyzed for gold . In the Star Lake area, ice direction is subparallel to the strike of several narrow northeast trending auriferous structures. arrow dispersion trains down-ice from known

Jan 1, 1986

By D. M. Baird

"THE Island of Newfoundland lies on the extreme eastern edge of the continent of North America and at the extreme northeastern end of the Appalachian geological province. Its belonging to the Appalachian province is shown in the geological history of the region and in the rock types and structures.Geosynclinal sedimentation in early and middle Palaeozoic times was interrupted by Taconic and, more profoundly, by Acadian, mountain building activity. Mid-Palaeo-zoic intrusions range from masses of serpentinized ultrabasic rocks to granite batholiths. A Carboniferous overlay of continental and shallow, drying sea types covers the earlier developed complex. Local basins in these times were filled with products of the erosion of tl1e earlier rocks, and, locally, grew the right kind of vegetation to make thin, discontinuons seams and pockets of coal. Post-early Pennsylvanian history is one of erosion and pene-planation with renewal of movement along many of the older fault systems."

Jan 1, 1960

By N. W. Hendry

ABSTRACT Exploration by geophysical methods and diamond drilling of an occurrence of chrysotile asbestos, located ten miles east of Matheson, Ontario, was commenced on March 25th, 1949, by the Canadian Johns-Manville Company, Limited. The asbestos is associated with a narrow sill-like body of basic and ultrabasic rocks which strikes northwesterly across portions of Munro and Beatty townships. To date, asbestos zones of commercial interest, many hundreds of feet in length, width, and depth, have been outlined by diamond drilling along a 2-mile length of serpentine. The fractures occupied by the asbestos veins are closely associated with the regional faulting in the area. The mining of the first occurrence, or A orebody, will be by open-pit methods. Milling will commence at a rate of 50 tons an hour. INTRODUCTION OCCURRENCES of chrysotile asbestos in Munro township have been known at least since 1914 and references to them appear in reports published by the Ontario Department of Mines in 1915 (1) and 1919 (2). J. G. Ross (3) in his excellent publication on Chrysotile Asbestos in Canada, mentions an occurrence in Munro township. The area was first mapped in detail by J. Satterly, of the Ontario Department of Mines, in 1944, and brief mention is made of chrysotile asbestos in Satterly's preliminary report (4), which was published the following year.

Jan 1, 1951

By Bryan Tisch

Goal of GMGE ??To advance mine reclamation through the beneficial use of organic residuals for the sustainable establishment of bioenergy crops and other productive land uses Objectives ??To advance the current ?standard? of mine reclamation by demonstrating that mining lands can safely become agriculturally ?productive? through the use of organic residuals. ??To generate and compile sound scientific data that can be utilized by stakeholders to better assess the environmental impacts of utilizing these materials. ??To complete a manual of best practices regarding the utilization of organic residuals on mine lands. *Considerable effort to be placed on operations/implementation side of utilizing residuals ?rather than just pure research

May 1, 2011

By F. Bourgeois, J. -S. Kroll-Rabotin

ABSTRACT: Falcon concentrators are enhanced gravity separators designed for concentrating fine particles. The Falcon UF model is unique in that it is dedicated to beneficiation of ultrafines, one key feature being that it does not make use of any fluidization water. We investigated the physics of particle transport inside Falcon concentrators, and concluded that separation efficiency is governed by differential settling velocity. We derived and published a predictive model of the partition function under dilute conditions. We intend to extend the initial model to concentrated ultrafine suspensions for application to industrial scenarios by adding hindered settling to account for solid concentration effects.

Jan 1, 2011

By Suzie Poulin, N. Geoffroy, G. P. Demopoulos

Most metallurgical industries generate toxic waste that must be treated prior to being released to the environment. However, in a lot of cases, the waste materials are poorly characterized or the analytical results are not well interpreted. These shortcomings often result in the development of inefficient industrial procedures, thus causing economic waste and difficulty meeting environmental regulations. Fortunately, a wide range of analytical techniques are available to guide researchers and engineers into making sound process development decisions. In this work, an industrial selenium and mercury removal process is used as an example to illustrate the application of X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) coupled with Energy-dispersive X-ray spectroscopy (EDX) and powder X-ray diffraction (PXRD) on solid waste. Furthermore, samples of analytical results are presented and interpreted and the modifications to the industrial process that resulted are explained. Finally, a brief description of the advantages and limitations of the aforementioned analytical techniques is given with an emphasis on industrial solid waste material.

Jan 1, 2011

By W. K. Gummer

"THE LOCATION of Canada's present aluminum industry is determined by availability of hydroelectric power, and ready access to ocean transport facilities. The chief raw material for the production of the metal is imported by ship over several thousand miles of water. In times of freedom of shipping and uncontested movement this provides the industry with its cheapest method of operation. However, during the early part of the last decade the general conditions of ocean and rail transportation were such that interest in the treatment of materials other than bauxite was greatly stimulated. This was the case not only in Canada, of course, but in most other countries.Canada has no deposits of bauxite and much research was carried out on other aluminous materials, chiefly silicates, in an effort to develop more or less economic and feasible methods of treatment. In the United States, this research was considerably more extensive. Some projects were early shown to be of little or no value, whereas others, including the widely publicized lime-sinter and soda-lime-sinter methods, became important. In North America, however, apart from the application of the sinter method to the hitherto waste-product (red mud) of the normal Bayer plant operation, none of these processes contributed appreciably to the production of aluminum during the war. In certain European countries, on the other hand, largely because of their situation with regard to bauxite deposits, they had a more general application, and Germany, for example, produced alumina from clay, ashes, and slag by at least four methods."

Jan 1, 1952

By Jacob Masliyah, Zhiang Zhou, Tshitende Kasongo, Jianjun Liu, Zhenghe Xu, Jeawon Choung

"Slime coating is a recognized challenge in fine particle flotation, not only in decreasing recovery, but also in reducing the selectivity and hence froth quality. In this presentation, a novel method based on electrophoretic mobility distribution measurement to study slime coatings is described. By measuring electrophoretic mobility distribution of individual minerals and their mixtures, the interactions between these minerals can be evaluated.For illustrative purposes, a model system of fine coals, or oil sands with two different types of fine clays was studied. Flotation tests showed a significant decrease in coal (bitumen) flotation recovery with montmorillonite but not with kaolinite clay addition. When electrophoretic mobility distribution of a fine coal/montmorillonite clay mixture was measured, a single modal zeta potential distribution was obtained, in contrast to a bimodal distribution for fine coalkaolinite clay mixture. This finding suggests a stronger adhesion of montmorillonite than kaolinite clays on fine coal surfaces. In the case of bitumen, the bimodal zeta potential distribution was measured for the mixture of bitumen emulsion and kaolinite or montmorillonite, indicating a weak attraction of the clays by bitumen. In the presence of calcium, however, a single modal zeta potential distribution was obtained in the mixture of bitumen emulsion with montmorillonite but not kaolinite clays. These findings are in excellent agreement with bitumen flotation results, demonstrating that the electrophoretic distribution measurement is a powerful tool to study slime coating phenomenon in a complex fine particle flotation system."

Jan 1, 2002

By Yong-neng Feng, Xiao-ping Chen, Wei Guo

"While the uniaxial compressive strength of rock has been extensively investigated, the relation between the saturation and natural compressive strength is relatively unexplored. This paper studies on 1865 statistical data of Chongqing Rail Transit Line 1 and Line 6, which located in the Middle Jurassic of Shaximiao formation. The research focuses on the relation between the saturation and natural compressive strength. The statistical data are categorized and quantified in order to ascertain the softening properties of sandstone and sandy mudstone. The findings suggest that the saturation compressive strength is significant effected by its natural compressive strength, and an empirical formula is introduced to explain the relation. These findings have implications for researchers and engineer who concerned with Chongqing rail transit construction.INTRODUCTIONIn the engineering construction and surrounding rock classification, the uniaxial compressive strength index (Ministry of Water Conservancy, 1995; Ministry of Railways, 1999) is one of the essential parameters of rock mass. Usually, there are two types of the uniaxial compressive strength index, natural and saturation compressive strength, and the ratio of them is the softening coefficient. Most of the previous studies on rock strength had focused on the influence factors (Liu et al., 2008; Liu et al., 1998; Liu et al., 2013; Wang, 2013; Zhang et al., 2008; Zhang et al., 2010; Zeng & Lin, 2003) with experiment and in-situ tests. But few publications that reports a long and formal research project on the relationship between natural and saturation compressive strength. In order to figure out this issue, this study investigated the distribution of Solidity Classification of Rock Mass and softening coefficient based on the statistical data of Chongqing Rail Transit Line 1 and Line 6. Based on the analysis, an empirical formula was proposed to explain the relationship."

Jan 1, 2015

By Steven Aiken

The East Boulder Mine located in Montana, U.S.A. utilizes snowmaking to assist with mine water treatment for nitrogen removal. Nitrogen species, including ammonia, are common contaminants in mine water from underground mining operations. Snowmaking provides secondary treatment of nitrogen during the winter due to the chemical and physical processes that occur during snowmaking, in the snow pack and in the snowmelt. The primary processes include atomization, evaporation, sublimation and volatilization. The snowmakers also provide secondary treatment for nitrogen removal when used as evaporators and/or land application units during the summer. In 2002, the snowmaking process was successful at reducing total nitrogen in the mine water by up to 87%. If additional losses due to soil and root zone processes are included, total nitrogen reduction would increase to between 87 and 97%. Snowmaking is an effective nitrogen reducing treatment method during the winter when other treatment methods such as land application cannot be used.

May 1, 2004

By J. H. Starkey

Large differences between macro and micro grindability relationships have been discovered for mill design measurements using the patented SAGDesign(TM) test. Crushing, Rod and Ball Mill Wi tests, and breakage parameter measurements have previously been used to design SAG mills but have not revealed the true magnitude of these differences. A SAGDesign(TM) test measures the SAG/Bond Wi Ratio (defined below) for every sample tested and gives a good design result because the F80 of the SAG stage test feed is 19 mm and because the test includes a Bond Ball Mill Work Index on SAG ground ore. Good flotation operation demands properly sized grinding mills and steady feed to the flotation circuit.

Jan 1, 2009

By T. Fekete, D. L. Flocks, R. T. Hart

The plugging effect of bacteria was investigated by injecting various concentrations of dead bacteria cells though sandstone cores. Pressure profiles along the cores were recorded periodically during the injection cycles. The plugging effect was analyzed using a plot of the ratio of reduced permeabilities to the initial permeability versus input volume. Results indicated that Tock permeability has little effect on plugging, but that the concentration of bacteria in the injection water has a significant effect on plugging characteristics. The pressure profile curves showed that bacteria penetrated several inches through the core but that the greater portion of the bacteria accumulated at the in-put end of the core.

Jan 1, 1960

By Geo. E. Cole

A GREAT deal of time and energy is now being devoted to the study of post-war reconstruction and rehabilitation, in spite of the fact that as yet we have not won the war in which we are presently engaged. If you feel that the study of post-war problems takes our thought away from the problem immediately before us, you may well query, "Well! What has all that to do with winning the war, our most urgent problem today?" The answer has been given by Principal James of McGill University, Chairman of the Cabinet Committee on Reconstruction: "Reconstruction is something which must be thought of in advance, partly for the purpose of recognizing exactly the influence of war-time activities, controls, and regulations on the post-war Canadian scene. Many people are acutely interested in this great problem. It is not that they are not interested in the war itself, or epochal events that are taking place from day to day. They have a vision of that future which they hope will be Canada's, and this vision inspires them to even greater efforts at the present time". The trend of events would indicate that changes, economic and industrial, after this war will be greatly out of line with those that followed previous wars in history, for the present struggle has involved every nation in the world. In the peace that will come, every engineer will have a task in bringing the most desirable order out of the most distressing chaos. We certainly are living in a changing world; we are witnessing geo-graphical and economic readjustments that no other generation in world's history has ever witnessed. And there is an opinion gaining strength in our Dominion, as in other lands, that after this war we shall live in a world in which our process of thinking and our very way of life will have to undergo drastic changes to cope with the new order of things. Sadly our world of today has had to revise the sublime vision that nation shall not lift up sword against nation, while salvage operations continue to beat ploughshares into tanks and the peaceful pruning-hook into a weapon for the deviltry of the commando.

Jan 1, 1943

By P. Nelson

Extending the campaign life of the Mitsubishi furnaces at Xstrata Copper's Kidd Metallurgical Division Copper Smelter has been a major focus of attention for many years. One aspect of this effort is real time monitoring to detect abnormal conditions and safely shut the furnaces down before significant damage occurs. Traditional real time methods of monitoring the integrity of refractory furnaces containing molten metal include alarms on individual temperatures of the refractory or cooling water. The need to set alarm limits which are not exceeded across the range of normal operating conditions leads to a system that only provides a limited warning, if any, before a failure occurs. Integrity monitoring systems that look at many different signals and alarm only changes in the relationships between the signals have been implemented on the smelting and converting furnaces. The systems are based on principle components analysis (PCA) models and implemented with the monitorMV software package. These provide much more sensitive and selective alarms so that changes in integrity are alarmed well in advance of any event. At a critical alarm level, the converting furnace is set to automatically shut down so that operating and technical personnel can review the situation. The configuration of the systems and operating experience with them will be discussed.

Jan 1, 2007

By H. R. Stockford

"A pyroxenite-carbonatite complex containing extensive pyrochlore mineralization was discovered during January, 1966, within an exploratory license area held by Consolidated Morrison Explorations Limited. Located 32 miles south of Moosonee, Ontario, the deposit was found under 100 feet of glacial till and Paleozoic sedimentary cover using airborne and ground magnetometer surveys. Exploratory and detailed drilling, totalling 47,625 feet in 85 holes, was completed in outlining the deposit to a maximum depth of 900 feet. Pyrochlore reserves are estimated at 62,000,000 tons averaging 0.52 per cent Cb,05 to a depth of 825 feet. Included in this tonnage is a high-grade section containing 10,000 tons per vertical foot grading 0.82 per cent Cb20 5• The deposit is still open at depth and the intrusive complex has by no means been fully explored.The columbium (niobium) mineralization occurs in a lineated calcite-dolomite host rock which has been intruded along a fault zone within a northeast-trending granulite belt. Potassium-argon dating indicates an age of 1655 million years.Preliminary studies suggest that the complex was intruded in a series of pulses in the form of a partially crystallized mush. The James Bay intrusive is unusual in that it is linear in form and contains only two main rock types - p•yroxenite and carbonatite. Nepheline-bearing syenites and associated rocks are notably absent. Moreover, the pyrochlore is essentially non-radioactive and free from many of the impurities generally associated with other pyrochlores. A test shaft to investigate soil conditions and to provide a 250-ton bulk sample was completed during 1968. Subsequent pilot-plant operations indicate that good quality pyrochlore concelttrates can be produced from this deposit."

Jan 1, 1972

By G. A. Vissac

IN THE preliminary design of a coal washery, the most important factor to evaluate is the ash content of the final product. The ash content permissible may be imposed by market demands, but, in the final analysis, sooner or later - as most consumers today are buying coal on a 'heat value' basis - the coal operator has a certain margin of latitude. and the ash content of the coal to be delivered can be determined on the basis of maximum returns and highest profits. A few years ago, the most desirable separation was selected on the basis of the plus-minus 0.10; that is, the most desirable gravity of the separation was selected at the point showing a minimum amount of near gravities in the raw coal. The reason for this was an expected wide error over these near gravities. Today with the recent development of cry accurate, automatically controlled cleaning apparatus, a much larger latitude is possible, and the most desirable gravity of separation can be selected, almost exclusively, on the basis of the economic factors involved. To illustrate these new methods of investigation we shall give two examples, based on actual coals from the western United States.

Jan 1, 1957

By J. A. H. Church

MR. J. A. H. CHURCH: The salient feature would seem to be that the thickness of the seam, in our coals at any rate, is the main factor in predisposition to spontaneous ignition. The evidence, incomplete it must be admitted, in the Saskatchewan and British Columbia fields, and complete in the Alberta field to my mind, shows this up very strongly. The German report on the upper Silesian coal fields definitely fixes the critical thickness at 13 feet, the British report goes far beyond this figure by stating that liability to ignition increases with the thickness of the seam over four feet. Before discussing the Alberta fires it would be well to note an error on page 12 -the probable cause of the fire in the Frank Mine should read "Spontaneous near fault. Heating first discovered 1909". Of the six fires attributed to spontaneous ignition all the seams were identical or in excess of the critical thickness mentioned in the German report. If there be any reason in the foregoing it is high time some forethought were taken to adopt some definite system of laying out the workings of such seams not so much on the outcrop districts as with a view to the future operation to the dip. Seams approaching 13 feet in thickness which to date have shown no disposition towards heating during the extraction of the outcrop areas may well cause infinite trouble or indeed total loss when the ventilating pressures increase as increase they must to the dip. This state of affairs can be combatted only by the adoption of a correct system of working and the provision of numerous airways of as large an area as may be compatible with the physical characteristics of the particular seam.

Jan 1, 1923

By D. A. Livingstone

Abstract Golden Manitou Mines, Limited, nine miles east of the town of Val d'Or in northwestern Quebec, are presently milling, at the rate of 1,000 tons daily, a relatively complex 3.11-phide ore and producing, in decreasing order of value, zinc, silver, gold, lead, and copper. The products are a zinc concentrate, a silver-lead-copper concentrate, and a silver-gold precipitate from cyanidation. Although several independent pre-production metallurgical investigations into the treatment of the ore were carried out, current practice is different from any of the recommended methods and, while still leaving room for improvement, is considerably more effective than earlier performance. Flow-sheet developments from the commencement of operations in 1942 are dealt with briefly, showing the reasons for making numerous changes, the shortcomings of the various schemes tried, and, finally, covering data pertinent to present-day practice. From the recovery standpoint, silver has presented the greatest difficulty. The writer's association with the Company coincided with the start of production. Characteristics of the Ore The predominant metallic minerals present in the ore, in decreasing order of their abundance, are: pyrite, sphalerite, galena and chalcopyrite, with lesser amounts of argentiferous tennantite-tetrahedrite, arsenopyrite, covellite, bornite, and chalcocite. The sphalerite is mostly light in colour, sometimes colourless, and practically free from combined iron. Some of the sphalerite is very closely associated with minor amounts of pyrite, chalcopyrite, and galena. Pyrie is abundantly disseminated as medium to fine grains; more rarely it is massive and contains occasional grains of sphalerite, galena, and chalcopyrite.

Jan 1, 1952

By S. Perez

Core drilling is a fundamental process in the mineral exploration industry. As deep exploration in hard rocks is accelerated due to the depletion of near ground mineral resources, deep-drilling operations need to reduce their reliance in operators experience and begin to implement new technologies in order to increase efficiency and cost-effectiveness of the overall process. Currently, lack of real-time information on the bit/rock interaction is a major problem. Therefore the mechanism behind the acoustic emission, which is a proven technique for remote monitoring, generation in mechanical rock cutting must be understood in order to provide real time information about the rock. This paper aims to identify the influence of mineral composition of granitic rocks on the acoustic emission (AE) during rock abrasivity test with a single contact tool and to evaluate the feasibility of AE as a means to infer Cerchar Abrasivity Index (CAI). Single contact tool will provide precise and accurate description of the source of AE. To provide constant grooving speed Cerchar apparatus was modified to monitor AE during rock/tool interaction. Tests on the modified Cerchar apparatus are carried out under the static load of 70N and cutting speed of 1 mm/s. A Scanning Electron Microscope (SEM) is utilized to visualize the groove in the rock and to identify the mineral composition through Back-Scattered Electrons (BSE) reflected from the rock sample. Based on the microscope images, it was found that biotite shows a larger groove area and plate-like fractures accompanied with burst-type AE signal, whereas plagioclase and quartz, which are characterized by similar hardness and BSE brightness, possess shattered-like fractures and more continuous-type AE signals. In addition, a-value of the Gutenberg-Richter scale has been found to well correlate with Cerchar Abrasivity Index (CAI).

Jan 1, 2015

By C. L. Lewis

"The development of computer process control at the Lake Dufault concentrator is reviewed and the on-stream X-ray analysis -computer system is described briefly. Some applications of the computer in metallurgical process control are described.The computer sequences slurry sample streams to the analyzer and translates the analytical results from voltage signals to elemental percentages. The required flotation reagent flow rates are calculated from analyses and mill-feed tonnage rates and the reagent feeders are set automatically to provide such flow rates. X-ray calibration time has been reduced from about 45 minutes to 15 minutes by the use of a computer program. Metallurgical and operating personnel have acquired the ability to program the computer and have extended the system capability to allow the calculation of recoveries, averaging of mill data, application of ore specific gravity in grinding control, control of oxidized ore flotation and the development of an economic recovery program."

Jan 1, 1971