Search Documents

By E. W. O'Brien

Personnel protection involves effective grounding and positive clearance of faults. This paper deals, in a general sense, with various schemes to achieve fool-proof personnel protection and reduce, to a minimum, the effects of human error and equipment failure.

Jan 1, 1966

By C. Yanqui

"Discontinuum Mechanics is based on two foundations: the idealization of the internal structure of substances, and the principle of the arithmetic mean value. For a linear discontinuum, the methods of Crystallography are used to describe their structure, in which nodes stands for the position of the homologous points such as molecules, grains, or any other motif. The principle of the mean value states that the value of any discrete function at a node is equal to the arithmetic average of the values of this function at the neighboring nodes. This principle leads to an elliptical linear differential equation of the second order, with coefficients given by the statistical second moments of the Cartesian components of the metric vector. As long as those coefficients are components of a symmetric second-order tensor, there are three mutually perpendicular directions, in which the variances reach their extreme values and the covariances are zero, showing that the mean value principle transforms the discontinuum into a statistically equivalent orthotropic continuum.The application of Discontinuum Mechanics to linear rock masses is simple and direct. It is sufficient to define the motif as the plane of geological discontinuity, and the metric vector as the normal vector to this plane, whose magnitude is the spacing between two consecutive planes belonging to the same set of discontinuities. Furthermore, heterogeneities of rock masses can be also included in this description by substituting the plane of discontinuity by a zone of weakness. In this way, the magnitude of the normal vector results from the product of the spacing and the RQD or the RMR. In going further in this theory, at least three conclusions show up. First, in the evaluation of rock masses, it is necessary to determine the orientation, spacing, and RMR for each set of discontinuities. Second, the conventional method of finding the principal families from the contours of equal concentration of poles on the stereographic projection excluding the spacing does not have any physical meaning. Third, any problem of rock mechanics can be solved in a rigorous and reliable way by integrating the differential equation of the mean value."

Jan 1, 2015

By J. H. Parliament

"The 15,000-tpd Similkameen open-pit copper mine, 10 miles south of Princeton, B.C., started production during 1972. The two main ore zones are separated by the deep canyon of the Similkameen River, with the Ingerbelle or western deposit being mined first. The location, design and construction of the plant were complicated by the steep terrain and the situation of the orebodies. Mining, utilizing 10-cu.yd electric shovels and 100-ton electric-wheel trucks, is conventional. Closely integrated with the preproduction mining was the construction of a 4-mile section of main highway to bypass the Ingerbelle pit. This entailed a very large fill, placed with mine equipment. Ore is crushed to minus 9 inches, stockpiled and reclaimed for direct delivery to three 32-ft-diameter by 14• ft single-stage autogenous grinding mills, each driven by two 4000-hp motors. Because of the friable ore in the upper part of the mine, 4-inch balls are added, with higher than design throughput attained. Classification is by 91>-inch spiral classifiers and cyclones. The flotation section comprises three parallel lines of ten 400-cu.ft rougher- scavenger cells and a single line of 100-cu.ft cleaner and recleaner cells. Concentrate is transported in end dump, closed trucks to Vancouver for dockside storage prior to shipment to the smelter. Tailings are piped across the canyon on a suspension bridge and through a tunnel to an empoundment area. Water is reclaimed and returned to the concentrator, forming a closed system. Dams are raised with cycloned ands, with the downstream section compacted."

Jan 1, 1973

By M. H. Leite, R. Corthésy, D. E. Gill

"La connaissance des contraintes naturelles qui prévalent dans les massifs rocheux est un prérequis indispensable pour la conception sécuritaire et économique des excavations comme on en retrouve dans les exploitations minières souterraines. Certains chercheurs se sont attardés à colliger les résultats de mesures de ces contraintes et les ont utilisés pour produire des modèles de prédiction basés sur leur traitement statistique. Ces modèles de prédiction sont très populaires auprès des exploitants miniers puisqu’ils permettent, du moins dans les étapes préliminaires de design, d’obtenir de façon s’apéconomique mais approximative, une partie des paramètres dont ils ont besoin. Dans le cadre d’un projet initié en 1994 avec la collaboration de l’IRSST, il a été décidé de produire un modèle de prédiction englobant une partie de la zone périphérique de la faille de Cadillac, soit une zone plus restreinte que le Bouclier Canadien utilisé jusqu’ici comme région pour l’élaboration de tels modèles. Pour produire ce modèle de nouvelles données obtenues avec une technique permettant d’exercer un excellent contrôle de qualité ont été ajoutées à celles déjà disponibles. Une telle régionalisation des données de base permet d’obtenir un modèle où les intensités et les orientations des contraintes principales sont beaucoup moins dispersées que ce que rapportent les modèles publiés jusqu’à ce jour. Enfin, il est démontré que le modèle proposé pour la région étudiée est en toute probabilité plus sécuritaire que les modèles plus généraux publiés à ce jour. Knowledge of the in situ state of stress existing in a rock mass is essential to the safe and economical design of underground mining excavations. Prediction models have been published, based on the statistical treatment of stress measurement results. Such prediction models are very popular among mine operators because they allow them, at least at a preliminary design stage, to economically obtain part of the information needed, even if this information is approximative. In 1994, a research project financed by IRSST was initiated aiming to produce a prediction model that would comprise a peripheral zone around the Cadillac fault. This region is more confined than the Canadian Shield on which the existing prediction models have been based up to now. In order to produce such a model, existing stress measurement results have been used in conjunction with new stress measurements that have been performed based on a technique which allows full control of the quality of the measurements. Restricting the data upon which the model is based to a more specific region gives a model in which the intensities and the orientations of principal stresses are far less scattered than the results published to date. Finally, it is shown that the proposed model is probably safer for the studied region than the models previously published."

Jan 1, 1998

By R. Darlington, S. Ji

"High pressure die casting is a promising process to make thin-wall components with high dimensional accuracy and excellent surface quality. However, the non-uniformity is one of the important features in castings. The inhomogeneity in tensile properties and microstructural characteristics were studied for the castings with different thicknesses made by high pressure die-cast Al-Mg-Si alloys. For the local mechanical properties in the die-castings, the casting skin provided the highest, whereas the casting centre provided the lowest yield strength, UTS and elongation. The yield strength, UTS and elongation were significantly decreased towards the casting centre. The microstructural inhomogeneity is characterised by the segregation of coarse fragmented dendrites, the reduction of solute concentrations of Mg and Si, and the increase of porosity level from the surface to the centre of castings. The growth velocities of eutectic a-Al phase estimated using the Jackson-Hunt model confirm that the growth variation is larger in the thin castings than that in thick castings.INTRODUCTION Inhomogeneity is an inherent characteristic in as-cast microstructures of a variety of alloys because of their non-uniform chemistry, microstructure, defects, topology and the resultant mechanical properties in the different ranges of localization (Campbell, 2003). Generally, three types of inhomogeneities characterise casting microstructures, which include (a) the casting defects of shrinkage and gas porosity, misruns, cold shuts, inclusions, hot tears and hot spots; (b) the non-uniform microstructure from the surface to the centre of castings; and (c) the non-uniform microstructure from the dendrites grown from primary solidification and the structure formed during the subsequent eutectic solidification in inter-dendritic regions. The chemical composition and the morphology between the primary dendrites and the inter-dendritic eutectics also differ in the as-cast microstructure. Obviously, the inhomogeneity is different in the castings obtained from different casting processes."

Jan 1, 2018

By F. McIntosh Galbraith

EMPLOYING geophysics to find ore was for a long time considered by the Canadian mining fraternity to be a performance of dubious value: in a category somewhere between the practice of sorcery, and using a divining rod to locate underground water. With increasing knowledge, however, and with constantly improving instruments, a solid speaking acquaintance with this adolescent science is becoming an integral part of the mining geologist's stock in trade. And quite properly so: for, in the established mining districts, the ore deposits which could be easily found, by ordinary prospecting methods, have already been located. There remain; however, in almost all of the principal mining camps, areas which are covered to varying depths by glacial debris; and it is here that the obvious opportunities exist for the successful application of geophysical methods. Geophysical results must always be considered in the closest possible relation to the local geology; and, in reality, the 'doodle-bugs' are simply additional tools for the geologist (in the same category with a plane table or a microscope). The Sudbury Basin is a shining example of precisely this state of affairs. Detailed geological mapping has not significantly altered the position of the outer norite contact as placed on Dr. Coleman's original map of the district. What detailed examination has done, of course, has been to reveal the accuracy with which the contact can be placed in different parts of the district, and to show up, in consequence, areas in which further work might reasonably be expected to disclose hitherto unknown or unsuspected ore. Viewed in this light, the proportion of the norite contact which is covered by substantial quantities of overburden is astonishingly large.

Jan 1, 1939

By D. Nie, M. Ren, T. Mo

This paper studied the phenomenon of room temperature creep deformation at crack tip and its effect on fatigue crack growth rate of a X-70 pipeline steel using compact-tension (CT) specimen on a MTS 810 testing machine. Time-dependent deformation at the crack tip under constant load was observed in this steel at room temperature and the amount of deformation produced was seen to depend on loading rate and the magnitude of stress intensity factor. It is found that there exists a critical stress intensity factor below which the deformation decreases with time when the applied load remains constant. It is also found that the occurrence of room temperature creep obviously affects the subsequent fatigue crack growth rate. The observed behavior was explained based on dislocation theory.

Jan 1, 2005

By G. C. Laurence

"This paper discusses the hazards and extensive precautions taken in Canadian uranium mines, concentrating plants and processing plants. It also outlines Canadian policy regarding the control of the sale and distribution of uranium and other nuclear materials.OVER THIRTY YEARS AGO, I spoke to The Canadian Institute of Mining and Metallurgy here in Montreal about radioactivity and its dangers. I must have made quite an impression thirty odd years ago, because now you have asked me to do it again. Of course, the picture has changed. Then they were mining uranium ore, recovering the radium from it and throwing away the uranium. Now they are still mining uranium ore, but are throwing the radium out on the tailings dumps. Thirty years ago, most people did not know what ""radioactivity"" meant. Nowadays, they have beard that it is dangerous, and some of them, recently, be-came worried about the radium in the tailings dumps and what becomes of it."

Jan 1, 1969

By H. Huang, H. M. Chen, W. B. Xie

Cu-0.8Cr-0.1Zr alloy were prepared by atmospheric melting. the microstructure and properties of the CuCrZr alloy after first cold rolled, solid solution, second cold rolled and aging treatment were analyzed by using optical microscope, electrical conductivity analysis and Vickers hardness tester. The results show that with the increase of the first cold rolled deformation, the grain breakage becomes more serious, and the cold hardening becomes more obvious and the hardness increases. The conductivity and peak hardness of the first cold rolled (reduction of 30% and 60%) alloys after solution, secondary cold rolled and aging treatment reaches 81 %IACS and 187 HV, respectively. However, the conductivity in the CuCrZr alloy with a higher rolling degree (reduction of 90%) after solution, secondary cold rolling and aging treatment is significantly higher, and the conductivity and peak hardness is 85.8 %IACS and 178 HV, respectively. INTRODUCTION CuCrZr alloy has been widely used in domestic industry for its excellent comprehensive properties such as high strength and high conductivity, especially in the contact wire and lead frame of high-speed railway (Sun, Tao, & Lu, 2015; Mishnev, Shakhova, Belyakov, & Kaibyshev, 2015; Zhang et al., 2016; Fu et al., 2017). In recent years, a lot of research has been done on how to improve the strength and conductivity of CuCrZr alloy. However, the high strength and high conductivity of copper alloys are contradictory characteristics. On the one hand, the addition of alloying elements is conducive to solution strengthening and aging strengthening; on the other hand, too much alloying elements in copper alloys cause defects in the lattice of copper matrix, resulting in a serious decline in the conductivity of copper alloys (Martienssen & Walirmont, 2005). How to obtain high strength and high conductivity at the same time is the main problem. At present, the main research methods are adding microalloying elements, thermomechanical treatment and severe plastic deformation to study the electrical conductivity and mechanical properties of CuCrZr alloys. For example, Xie et al. (2011) added trace Ag to the Cu-0.26 wt%Cr-0.08 wt%Zr alloy, and the size of precipitated phase Cr and Cu4Zr became smaller and the mechanical properties of the alloy were improved. Su, Dong, Liu, Li, & Kang (2004) found that the addition of trace Mg in CuCrZr alloy inhibits the growth of precipitated phase and reduces the internal stress around the precipitated phase. At the same time, the size of precipitated phase becomes smaller and the peak aging strength of the alloy is improved. Pang et al. (2013) found that adding trace Ni and Si to the CuCrZr alloy could improve the peak hardness, softening resistance and precipitation morphology of the alloy. Experiments shows that the grain size was significantly refined by equal channel angular extrusion combined with aging treatment, while the strength of the alloy was increased, and the electrical conductivity of the alloy did not decrease (Vinogradov, Patlan, Suzuki, Kitagawa, & Kopylov, 2002; Saray, 2016); Kermajani, Raygan, Hanayi, & Ghaffari (2013) showed that the strength of CuCrZr alloy can be improved by rolling at 500 °C. After 150 minutes of aging treatment, the strength and conductivity of the material increased to 431 MPa and 81 %IACS, respectively. Takata, Ohtake, Kita, Kitagawa, and Tsuji (2009) noted that the strain hardening, uniform elongation and tensile strength of the nano-precipitates produced by the mechanical heat treatment process can be notable enhanced. The mechanical and electrical properties of CuCrZr alloy can be improved by combining large plastic deformation with aging treatment in the test process (Gao, Huttunen-Saarivirta, Tiainen, & Hemmila, 2003; Huang et al., 2003; Xia et al., 2012; Zel’dovich et al., 2014).

Jan 1, 2019

By LUKE O. LINDOE

A major clay products industry in the Medicine Hat area since before 1910 has maintained a continued interest in the clays of the Cypress Hills. For the first forty years the materials used were local red-burning Cretaceous and Pleistocene clays and sands and high-quality stoneware clays of the Whitemud Formation at Eastend, Saskatchewan. Recently a much broader spectrum of raw materials has been brought into use. Including the exposures of the Eagle Butte structure, the Cypress Hills present a 1200 m section of clay-like sediments. Of this 1200 m about 94 per cent, the high montmorillonite shales of the Upper Cretaceous, can be considered useless, or nearly so; the remaining six per cent, all fresh-water beds, presents a wide variety of potentially useful materials. The development of these clay resources is complicated by deep surface creep on the south flank of the Cypress Hills, by largescale slumping on the north flank and by a structural complex in the Eagle Butte area.

Jan 1, 1984

By Takayuki Takasugi, Naoya Masahashi, Yasuyuki Kaneno, Satoshi Semboshi, Yusuke Kadoi

Cu–Ti alloy wires doped with and without a small amount of Ni were fabricated by over-aging and using intense drawing procedures. For both the Cu–Ti alloys with and without Ni doping, the over- aged microstructure was occupied fully with a coarse lamella of Cu solid solution and β-Cu4Ti plates precipitated discontinuously by grain boundary reactions. The full-lamellar microstructure was developed much more rapidly by aging in multi steps at 873 K to 723 K rather than by isothermal aging at 723 K. Ni doping in Cu-Ti alloy was also effective to accelerate the formation of the lamellar microstructure. When drawing the over-aged alloy with inferior hardness but superior electrical conductivity, the strength increased steadily and eventually exceeded that for the wires drawn from the peak-aged alloy. In addition, the electrical conductivity of the wires drawn from the over-aged alloy was always much greater than that from the peak-aged alloy. Eventually, the procedure of over-aging, followed by intense drawing, could enhance both the strength and electrical conductivity of Cu-Ti alloys, whichever they contain a small amount of Ni or not, rather than the conventional peak-aging and drawing process. INTRODUCTION Cu-based alloy wires, which have an excellent combination of strength and electrical conductivity, have attracted extensive attention for highly mechanically stressed electrical devices, such as conductive lead wires and wires in suspension springs. Cu-Be alloys are widely used for such electrical components owing to their combination of strength and electrical conductivity among industrial Cu-based alloys. However, since beryllium is potentially toxic and also a rare element, substitute materials for Cu-Be alloys have been searched for several decades. Age-hardenable Cu–Ti based alloys have been proposed as candidates because their mechanical and physical properties are comparable to those of Cu-Be alloys; however, their electrical conductivity is inferior (Datta & Soffa, 1976; Soffa & Laughlin, 2004). In order to satisfy the requirement of downsizing and streamlining electrical devices, further improvement of the mechanical and electrical properties of Cu–Ti alloy wires is needed. Age-hardenable Cu–Ti alloys, which contain approximately 3 to 6 at.% Ti, are typically prepared using a solid solution treatment above 1100 K and then aging at a moderate temperature of 700 K to 800 K. It has been revealed that the microstructural events during aging progress as follows (Soffa & Laughlin, 2004): (1) compositional modulation of the parent supersaturated Cu solid solution in an initial aging stage (Laughlin & Cahn, 1975), (2) continuous nucleation and growth of fine needle-shaped precipitates of metastable β’-Cu4Ti with a tetragonal structure in a peak-aged stage, and (3) discontinuous precipitation of cellular components laminating the plates of a terminal Cu solid solution and stable β-Cu4Ti with an orthorhombic structure at the grain boundaries in an over-aging stage. It has been also accepted that the highest number density of dispersed fine β’-Cu4Ti needles should contribute to maximal strengthening. On the other hand, decease of the strength in the over-aging stage occurs due to the replacement of the fine β’- Cu4Ti needles with cellular components containing coarse β-Cu4Ti plates, while the electrical conductivity is significantly enhanced due to the depletion of solute Ti in the Cu matrix. This suggests that a combination of strength and electrical conductivity for age-hardenable Cu-Ti alloys is in a trade-off relationship, and that innovative improvement of both properties might be limited to tuning the aging conditions.

Jan 1, 2019

"The most widely used method for predicting the onset of continuous caving is Laubscher’s caving chart. A detailed examination of this method was undertaken which concluded that it had limitations which may impact on results, particularly when dealing with stronger rock masses that are outside current experience. These limitations relate to inadequate guidelines for adjustment factors to rock mass rating (RMR), concerns about the position on the chart of critical case history data, undocumented changes to the method and an inadequate number of data points to be confident of stability boundaries.A review was undertaken on the application and reliability of a numerical method of assessing cavability. The review highlighted a number of issues, which at this stage, make numerical continuum methods problematic for predicting cavability. This is in particular reference to sensitivity to input parameters that are difficult to determine accurately and mesh dependency.An extended version of the Mathews method for open stope design was developed as an alternative method of predicting the onset of continuous caving. A number of caving case histories were collected and analyzed and a caving boundary delineated statistically on the Mathews stability graph. The definition of the caving boundary was aided by the existence of a large and wide-ranging stability database from non-caving mines. A caving rate model was extrapolated from the extended Mathews stability graph but could only be partially validated due to a lack of reliable data."

Jan 1, 2003

By F. Bruey, T. Bruce, D. R. Nagaraj, W. Thomas, P. Riccio, E. Guitard

"AEROPHINE® 3418A Promoter is a flotation collector that has been an industry standard in the Canadian mineral processing industry since its first commercial use at the Kidd Creek concentrator in 1980. Its wide range of applications in sulphide mineral flotation has made it successful, specifically in the processing of complex sulphide ores which contain copper, lead, zinc, and silver or any combination of these elements for selective separation.AEROPHINE® 3418A Promoter is a unique, phosphine-based collector originally developed for the flotation of copper sulphide minerals and activated zinc minerals. It is now recognized for its selectivity for complex, polymetallic sulphide ores and porphyry copper ores. In addition, AEROPHINE® 3418A Promoter is highly selective for copper, lead, activated zinc, nickel and precious metals. AEROPHINE® 3418A Promoter exhibits strength yet, selectivity against iron sulphides (pyrite, pyrrhotite, marcasite, and arsenopyrite), non-activated sphalerite, and many minerals which contain penalty elements.This paper outlines a brief history of the product’s development, its historical use in Canada and several potential innovative mineral processing applications with the use of the chemistry. Three Canadian case studies will be presented on various ore types including: a Cu-Au ore, a Cu-Zn ore, and Cu-Pb-Zn ore. A plant production update will also be given on the future supply of AEROPHINE® 3418A Promoter.INTRODUCTIONCytec Industries Inc. operates a phosphine derivatives plant in Niagara Falls, Ontario, that manufactures various products for their speciality chemicals division. The products from this site are based on phosphine (PH3) chemistry and are used in a variety of markets including electronics, agriculture, LED lighting, water treatment, metal extraction, and mineral processing. One of the major products is the phosphine-based sulphide mineral collector, AEROPHINE® 3418A Promoter.AEROPHINE® 3418A Promoter (Figure 1) was originally developed for the flotation of copper and activated zinc minerals (Thomas, 2010).."

Jan 1, 2015

By K. D. A. Whaley

Abstract -The Captain North Extension deposit consists of five sulfide lenses hosted in cherty and chloritic metasediment that is bounded by quartz-eye rhyolite and laminated rhyolite . Lens 2 consists of sphalerite and galena with silver-rich tetrahedrite in chert. Lens 3 contains massive pyrite, with chalcopyrite and minor gold, gradational to minor pyrite in a chloritic metasediment . The other lenses are unexplored. The sulfides occur as beds, fracture infills, and disseminated grains. Reserves are estimated at 207 555 tonnes grading 7.38% Zn, 2.76% Pb, and 91.81 g/t Ag. The deposit is isoclinally folded, dips steeply west, plunges 50 degrees south, and is faulted out to the north, where drag folding has reversed the plunge. Minor cross-faults contain talc and sericite. High sphalerite but low pyrite abundances result in poor responses to standard electromagnetic techniques. Lens 3, which contains more pyrite than Lens 2, responds better to induced polarization and allows detection. Geochemical anomalies are found in a nearby swamp and stream, but an impervious till cover inhibits the development of soil anomalies.

Jan 1, 1992

By W. M. G. Heeley

In the province of Alberta the coal measures dip at so many different angles, between the horizontal and the vertical, that many different systems of haulage are in use. I will, however, only touch briefly upon the general -systems in use, and devote the major portion of this paper to a discussion of endless-rope haulage and its adaptibility to various conditions in coal mines; dealing in particular with the endless-rope haulage that was installed at Brule during the month of August 1923. In coal seams that are approximately level, and newly opened, hand-putting or tramming from the face is the cheapest, but when the mine is further developed tramming is out of the question, and the use of ponies is the next consideration. The time arrives, however, when mining reaches a point where the economical haulage of coal by horses cannot be done profitably, and then some system of mechanical haulage must be installed. The installation of any system should be carefully considered before any particular type of haulage is adopted, because a great deal depends upon the grade or dip of the seam. Motor haulage is impossible to operate profitably on a grade of over 6 per cent and, while it is possible to use ponies, on short runs, up to 9 per cent, some other means of main and secondary haulage must be installed when a 9 per cent grade, is exceeded. I will, therefore, deal first with secondary haulage, because even though a main haulage is established, secondary haulage can be used to feed the main haulage.

Jan 1, 1925

By J. A. Allan

The utilization of natural deposits of salt is one of the oldest industries in Alberta. In 1820, Sir James Richardson visited Salt river, and in the same year D. W. Harmon states chat "clown Slave river, there are several places, where almost any quantity of excellent dean white salt may be taken, with as much ease as sand along the seashore. From these places the greater part of the northwest is supplied with this valuable article". This reference is to the salt chat occurs around springs on Salt river at the northern boundary of the Province. This and other occurrences will be described later in this paper. It is not on account of the development of salt and gypsum in Alberta chat this paper has been prepared, but rather to draw attention to the widespread distribution of salt-bearing and gypsum-bearing rocks, and to the stratigraphic importance of these rocks . The origin of the deposits of salt, gypsum, anhydrite, and dolomite is discussed, and the economic significance of these minerals is considered. There is no salt production reported from Alberta in 1928.

Jan 1, 1929

By Paul B. Warrington

This paper presents a discussion of the factors affecting copper scrap markets, including such items as price levels, freight. grades of material, sources and packaging. Reference will also be made to the effective life and turn-around of the copper content of some products. Introduction IN TERMS OF SIZE, copper scrap is second only to ferrous scrap in tonnage recycled. However, in total value, it is second to none. For example, world scrap recovery during the preceding 4 years averaged just under 2,300,000 metric tons per annum, and at an average price of 70 ¢ a pound, this works out at a turnover of about $3.5 billion, which indicates that the copper scrap industry, or recycling as it is now becoming known , is a substantial one.

Jan 1, 1977

By Jean-Jacques Bouillon, Michel Jébrak, Stephane Faure

"Le gisement polymétallique (Cu-Zn-Au-Ag) des Mines Selbaie est forme par un réseau de filons encaisses dans une séquence de pyroclastites felsiques du sill on Harricana-Turgeon. Les minéralisations sont encaissées dans le tuf de Selbaie, situe sous une épaisse séquence d'ignimbrites Iitées. Ce gisement se distingue des autres gites archéens par une chronologie atypique des minéralisations: les veines de chalcopyrite, de sphalérite et de galène recoupent un amas exhalatifpyriteux stérile. Un vaste halo d'altération hydrothermale a chlorite et mica blanc est associe à cette minéralisation.La mise en place des veines minéralisées est associée à une phase d'extension NNW-SSE. Le complexe volcanique subit, par la suite, trois phases de déformation. Une compression, orienté N-S, développe une schistosité à peine pénétrative et un réseau de fentes de tension. Une réorientation des contraintes locales selon une direction WNW-ESE conduit au chevauchement de I' écaille d'andésite et de tonalite de Brouillan. Un réseau conjugue de failles normales cassantes est associe au relâchement des contraintes."

Jan 1, 1990

By P. R. Jones

"The paper describes the CDN$400 million expansion at Hudson Bay Mining and Smelting Co., Limited’s operations. The company has continuously produced copper and zinc at the Flin Flon metallurgical plant since 1930. The paper details the company’s operational turnaround since 1995 and “The 777 Project” which includes two new mines, expansion and modification of the concentrators, expansion of the zinc pressure leach plant, a new zinc electrolytic cellhouse and modifications to the copper smelter gas handling system to reduce ground level gas emissions. IntroductionHudson Bay Mining and Smelting Co., Limited (HBMS) was incorporated in 1927 to mine and process the world-class Flin Flon copper and zinc orebody. Ore concentration and metallurgical facilities were constructed in Flin Flon. The metallurgical complex capability is currently 89 000 tonnes of copper metal and 98 000 tonnes of zinc metal from both HBMS and purchased concentrates.Flin Flon, with a population of 7000, is in Manitoba and partly in the province of Saskatchewan. The location is isolated with Winnipeg 800 km to the south and Saskatoon 500 km southwest.Today, three underground mines feed the Flin Flon concentrator, one feeds the Ruttan concentrator at Leaf Rapids, 200 km to the north of Flin Flon, and Chisel North mine feeds the Snow Lake concentrator (Fig. 1).The Flin Flon volcanic massive sulphide proximal and distal orebodies are within the Flin Flon greenstone belt which stretches from the west of Flin Flon to the east of Snow Lake, a distance of 250 km. The belt is approximately 100 km wide before disappearing below the paleozoic cover to the south."

Jan 1, 2001

By R. Lasmanis, W. C. Utterback

"The Mount Tolman porphyry Mo-Cu deposit is 64 km south of Republic, Ferry County, Washington. It occurs in the composite Keller Butte pluton, which consists of the Keller Butte porphyritic biotite granite and granodiorite, the Mount Tolman quartz porphyry granite, and the Meadow Creek biotite granite phases. The three phases range in age from 61.3 Ma ± 2.3 Ma to 55.7 Ma ±2.0 Ma. The stockwork deposit occurs in the Keller Butte phase above the contact with the Mount Tolman quartz porphyry granite.Mount Tolman is a hybrid calc-alkaline deposit that has features of both a Climax-type and a plutonic type. Prior to post-ore faulting, the deposit had a flattened hood like shape. In plan it is elongated- 1.6 km wide, 3.2 km long, and up to 609 m thick. The orebody has a 292 o strike. It contains a geologic reserve exceeding 2.18 billion tonnes of ore averaging 0.093% MoS2 and 0.09o/o Cu using a 0.048% MoS2 cutoff. Of this total, 816 million tonnes of measured and indicated ore averaging 0.097% MoS2 and 0.09o/o Cu could be mined by open pit with an overall waste-to-ore ratio of 0.91 to 1.The deposit is a stockwork of quartz and quartz-sericite-pyrite veins and fracture fillings that contain molybdenite, chalcopyrite, sphalerite, and magnetite. Five separate episodes of fracturing and mineralization produced the orebody and were followed by four additional episodes of fracturing with sulrgrade mineralization. The Mount Tolman deposit contains propylitic, argillic, phyllic, topaz greisen, and potassic alteration zones. Extensive silicification overlaps the K-feldspathized, quartz-topaz, and phyllic alteration zones."

Jan 1, 1995