Search Documents

By D. Van Tonder

ABSTRACT The comparative economics of ion exchange and direct precipitation have been analyzed by developing indicative CAPEX/OPEX models for typical alkaline leach uranium circuits. An agitated tank ore leach application is considered, comparing resin-in-pulp and direct precipitation as recovery options. Capital and operating cost estimates are derived from rates and factors used in recent studies and projects. The analysis showed the main economic drivers to be the ore grade and resin loading. The resin loading is impacted by the prevalence of competing ions, especially chloride. At resin-in-pulp solution chloride concentrations below 3 g/L and uranium grade below 640 g/t U3O8, resin-in-pulp is more economical, whereas at chloride concentrations above 3 g/L, direct precipitation is more economical.

Jan 1, 2012

By A. E. Wraith, R. Harris, J. Qiu, R. Parra

Small pilot scale experiments have shown that it is possible to almost fully eliminate the minor elements (ME), namely As, Sb, Bi and Pb contained in smelter dusts by vacuum calcination of mixtures of the dust with sulphidizing agents such as dirty copper concentrate or elemental sulphur at 900 °C and 80 +/- 30 Pa for 90 minutes. The products of this calcination are a residue comprising a purified mixture of copper containing compounds along with the gangue constituents and a high sulphur condensate comprising a mixture of the minor element compounds. In particular, the Cu:ME ratios of the concentrate and dust were increased from 250 and 50, from 28 and 12 and from 36 and 8 to roughly 3000, 3000 and 100 for the calcine, for Bi, As and Sb, respectively. It has also been calculated that (i) the copper content of the vacuum calcine may be recovered by feeding it into a Peirce-Smith converter during its slag blow, and (ii) the resulting recycling could increase the minor element treatment capacity of a smelter by 100 % while also reducing the blister As content by a factor of three. The experimental results are briefly discussed and a treated dust recycling option is examined. Example operating conditions are presented and available commercial technology for the vacuum calcination of the mixtures is reviewed.

Jan 1, 2007

By M. Normandin

The performance of various polymers and other macromolecules used to flocculate red mud particulate materials in the Bayer process can be evaluated on the basis of their efficiency to achieve adequate settling velocity and turbidity level, The Jar Test is widely used in the mineral industry to determine the efficiency of solid-liquid separation processes, particularly for gravity settler of the Bayer process. However, a high level of variability is found in the data obtained by this methodology, In this study, different parameters of the cylinder test procedure are evaluated to determine their role in the overall variability of the method, As demonstrated by laboratory testing, the overall variability can be considerably reduced by good laboratory practices.

Jan 1, 2005

By A. B. Morrow

Consulting engineers are well aware of large variations in plant operating cultures between countries, companies, and even within sites and operating crews. These operating cultures must be considered when designing Advanced Process Control (APC) applications in order to maximize utilization rates and return on investment. Designs must be driven by an understanding of the totality of unit operations. Economic factors, equipment constraints, management philosophy, maintenance department responsiveness, instrumentation reliability, operating crew skills and teamwork, and individual operator concerns are all important and must be considered during application design. A general approach to incorporating operating culture considerations into APC application design is described. A case study for an iron ore concentrator plant is presented.

Jan 1, 2014

By Alan D. Curtis

A standard planning block model for Phelps Dodge North America Operations has been developed to improve mine planning efficiency and performance in a skill starved environment. The model saves time on software management and training, consolidates data and standard information/output, enhances evaluation and strategic process, and improves communication between sites.

May 1, 2007

By W. Dingley, G. R. Hoey

"AbstractWear of six types of grinding balls was compared with and without corrosion inhibition in grinding Ni-Cu sulphide and hematite ores in laboratory ball mills. Forged steel balls (Rc 60 to 65) and three types of white cast iron balls (Rc 50 to 65) were susceptible to corrosive wear and two types of stainless steel balls [AISI Type 440C (Rc 65) and AISI Type 302 is; 35)] were relatively immune. The relative wear rates of the five types of hard balls (Rc 50 to 65) were dependent on the corrosivity of the ore. Ranking of the hard balls with respect to wear resistance was consistent for the sulphide and hematite ores in the presence of corrosion inhibition, whereas their ranking was different for the two ores in the absence of inhibition.The electrochemical potential of the grinding balls was measured during grinding and was found to be a useful measurement for assessing the susceptibility of an alloy to corrosive wear. Reduction of ball wear for forged steel and white cast irons with corrosion inhibition was concomitant with a shift of ball potential to less active values. Ball potentials in the presence of inhibition were indicative of non-corroding metal surfaces.IntroductionA PREVIOUS STUDY by the authors (1) showed that corrosion inhibitors - sodium nitrite, sodium chromate and sodium metasilicate - reduced wear of forged steel grinding balls by up to 49% in grinding Ni-Cu sulphide ore. Although the mechanism of wear reduction was not elucidated, it was concluded that corrosion must play a significant role in the wear of grinding media. Remark and Wick (2) of Battelle Pacific Northwest Laboratories have also evaluated corrosion inhibitors for the reduction of metal wear using abrasive and n on- abrasive te sting procedures. Their research was sponsored by 16 companies throughout the world. Preliminary results indicated that anodic inhibitors prevent from one-fourth to one-half of the loss due to corrosion."

Jan 1, 1977

By C. Blawert

The corrosion properties of the skin and the bulk of semi-solid processed and high pressure die cast AZ91 alloy were studied in 5% NaCI solution by (a) analysing the corrosion morphology, (b) measuring electrochemical polarization curves, (c) performing electrochemical impedance spectroscopic measurements, and (d) immersion tests at constant pH-values. Using XRD, LM, SEM and EDX to evaluate the microstructure of skin and bulk specimens, the corrosion results were related to the microstructures of the particular alloys. However, microstructure and corrosion performance were found to be similar for both production processes, and only slight but distinct differences were found. Generally, the skin corrosion properties are inferior to those of the bulk, with the exception of the high pressure die cast AZ91 alloy, where the finer microstructure of the skin layer exhibits a better performance as showed by impedance studies and confirmed in long term immersion tests.

Jan 1, 2004

By Ben Cottrell

In this paper technical drilling is referred to as the process of collecting engineering and metallurgical parameters for subsequent mine design considerations. Throughout the development of a mineral exploration property there are various opportunities to ?piggy-back? technical drilling onto the routine exploration drilling process, helping to reduce future costs and delays associated with re-drilling and missing information. This article is written from the engineers and metallurgists point of view, to outline some best practices for exploration borehole planning and technical data collection requirements.

Aug 1, 2013

By N. M. Steven, J. M. Moore, J. L. Kuyper

Abstract - Mineral exploration and research has led to the identification of four types of tungsten mineralization in the NE-trending, largely ensialic, inland branch of the late Proterozoic/early Paleozoic Pan-African Damara Orogen. The mineralization (mainly scheelite) occurs in a terrane (the Central Zone) that is characterized by multiple deformation, greenschist/amphibolite-facies metamorphism and numerous peraluminous S-type granitic and pegmatitic intrusions. The four major types of scheelite mineralization are (in ascending stratigraphie order of host rock): (1) thin (5 cm to 2 meter) quartz+ plagioclase+ diopside ± scapolite cale-silicate granofels with finely disseminated scheelite (scheelite-bearing granofels; SBG) developed as discontinuous intercalations within the cale-silicate rocks of the Khan, Spes Bona, Oberwasser and Kuiseb Formations (Nosib and Swakop Groups); garnet+ pyroxene ± vesuvianite + scheelite ± fluorite replacement skarns hosted by Okawayo, Karibib and lower Kuiseb Formation marbles in the aureoles of late tectonic, unmineralized leucogranites; metaturbidite-hosted scheelite- (and possibly wolfrarnite-) bearing tourmalinites, both stratiform and crosscutting, in the Kuiseb Formation located in the 'cleavage fronts' of late tectonic granitoids; scheelite-bearing vesuvianite +quartz+ garnet skarnoid rocks (several hundred meters in length) in the calcareous metaturbidites of the upper Kuiseb Formation. These scheelite occurrences were discovered by the follow-up of a large number of tungsten anomalies located during a regional stream sediment sampling program. Detailed mapping, ultra-violet surveys and rock sampling proved to be the most effective surface exploration techniques for locating mineralization; soil sampling and geophysics were of almost no use. The largest, continuous scheelite-bearing skarn of economic interest, Otjua, has a drill-indicated reserve of 250 000 tonnes at 0.53 wt% W03 and 8 wt% CaF2.

Jan 1, 1994

By Mark Rebagliati, John Payne, Jim Oliver

Abstract-The Campo Morado precious-metal-bearing, volcanogenic massive sulfide deposits occur in a lower Cretaceous, bimodal, calc-alkaline volcanic sequence in a major northerly trending belt in the Guerrero Terrane in northeastern Guerrero, Mexico. During upper Cretaceous to Early Tertiary greenschist-facies regional metamorphism, the rocks were deformed strongly into a northeast-verging fold-and-thrust belt. Three later stages of weak deformation were dominated, respectively, by kink folds, broad warps, and extensional faults. Most deposits occur in the upper part of a sequence of felsic flows and heterolithic volcanoclastic rocks or at its contact with overlying chert and argillite-sandstone. The Reforma and El Rey massive sulfide deposits are on the overturned limb of a major, thrusted anticline, and the Naranjo and El Largo massive sulfide deposits are to the south on the upright limb of the same major fold. The La Lucha and San Rafael massive sulfide occurrences are in an upper plate to the southwest which was thrusted over the plate containing the Naranjo and El Largo deposits. In several of the deposits, Au, Ag, Zn, and Pb are concentrated near the stratigraphic top, and Cu is concentrated near the stratigraphic base. Major minerals are pyrite, quartz, ankerite, sphalerite, chalcopyrite, and galena. Minor minerals are tennantite-freibergite, arsenopyrite, and pyrrhotite. Gold and Ag occur in argentian gold, and Ag also occurs in tennantite-freibergite. The cumulative inferred resource of massive sulfide for the Reforma, Naranjo, El Rey, and El Largo deposits exceeds 30 Mt, with the latter two deposits incompletely delineated. Underlying pyrite-quartz stockwork zones contain chalcopyrite, chlorite, and sphalerite. Hydrothermal alteration minerals in the stratigraphic footwall are pyrite, quartz, chlorite, ferroan dolomite, and ankerite. In the stratigraphic hangingwall, hydrothermal alteration minerals are sericite, calcite-dolomite, and lesser clay minerals and quartz. The deposits belong to a low-sulfidation, volcanogenic massive sulfide system formed in a subaqueous environment, and are of the bimodal, siliciclastic type.

Jan 1, 1997

By E. Asselin, P. Sauve, H. Salomon-de-Friedberg

"Residues from the CESL Copper process were leached using the CESL Gold process. The kinetics of reaction were confirmed to be fast with over 50% of the gold consistently extracted within 2 minutes of leaching. Final gold extractions under the conditions tested here were between 80-90% obtained within 90 minutes. A model for the CESL Gold process was developed. This model is slightly different based on whether the copper concentrate leach residue was ground or unground prior to leaching: the gold leaching rate constant is approximately twice as fast for the ground samples. Unground residues had a P80 of 13 ?m whereas ground residues had a P80 of 10 ?m. The model predicts a 43% decrease in leaching time for ground residue versus unground residue to achieve the same extraction under otherwise identical conditions. The model was more accurate for the ground samples. INTRODUCTIONTeck's CESL Process (Jones, 1996) was developed to provide an economically attractive alternative to traditional copper smelting. It has since evolved to also deal with copper concentrates containing valuable impurities such as nickel and undesirable ones, such as arsenic, while reducing downstream costs. Effective recovery of gold and silver is essential to the economics of the CESL Process. The Brook Hunt 2007 copper concentrate assay data (Wood-Mackenzie, 2007) were examined to determine the ratio of gold plus silver value relative to the contained copper. As indicated in Figure 1 below, nearly two-thirds of concentrates have 10% or more of their total value tied up in their precious metals content.CESL has extensively examined the recovery of gold and silver at bench, pilot and demonstration scale, which has culminated in the present CESL Gold Process (Barr et al., 2007). The process targets the precious metal contained in the leach residues produced in the copper portion of the flowsheet. This residue has two primary components which influence downstream processing. The major iron-rich fraction (-75 wt%) of the residue is a mixture of various forms of iron oxide precipitates including hematite and jarosite (Sahu and Asselin, 2011). The iron fraction ranges from amorphous to crystalline in nature depending on the compound precipitated, upstream operating conditions and feed material composition. The lesser, but by no means less important, fraction is a mixture of elemental sulphur and unreacted sulphides (principally pyrite).Elemental sulphur formed during the oxidative leach of the copper concentrate reacts with cyanide to form thiocyanate (SCN-) making a traditional cyanide leach approach too costly. Since the SCN formation reaction strongly depends on contact time with the CESL residues (Po, 2007) short contact times were preferred. This factor guided the development work towards the eventual room temperature, pressure cyanidation process which results in near complete gold dissolution in 90 minutes. A recent CESL gold demonstration campaign treating 1.5 t/d of residue from the copper oxidation step achieved an average gold extraction of 91% (96% maximum)."

Jan 1, 2012

By K. K. Feng

"Spontaneous combustion has always been a problem in coal mines and is identified mainly with the mining of low-rank coals. The liability of coals to spontaneous heating is only one of the factors in determining whether spontaneous combustion will occur. However, knowledge of the relative oxidizability of the coal is a useful factor to take into consideration when selecting new coal seams and mining methods for future mine development.Four methods (static isothermal, ignitability, adiabatic and dynamic) have been used to compare the relative liability of Canadian coal to spontaneous combustion and to investigate the mechanism of spontaneous combustion of these coals. Among these f our methods, the static isothermal method is considered to be the best indicator of the susceptibility of various coals to spontaneous combustion. Western mountain coal adsorbs more oxygen and has a higher tendency to undergo spontaneous combustion than the Harbour seam coal of Nova Scotia. It has also been observed that a higher methane content in coal will indicate a lower liability to spontaneous heating."

Jan 1, 1985

By Paul Toor

The operation of SAG mills is variable over time due to their continually changing liner shape, mass and subsequent load motion. However, this tends to be poorly accommodated in liner design and mill control, with only limited compensation made for this influence, usually in the first few weeks after a new liner is installed. With ever-increasing ore competency, increasing energy costs and decreasing ore grades, simplified design and operational approaches that compromise the achievable mill efficiency are no longer adequate. This paper presents a methodology that has been developed to measure and account for the changes in mill performance as the liner wears. This involves monitoring all liner profiles ? in other words the three-dimensional liner shape - over the life of the liner, then conducting controlled surveys at different stages of the liner wear life, and correlating the mill performance to the liner profiles. The measured liner mass is modelled to provide an ongoing meaningful load mass measure that excludes the liner mass.

Jan 1, 2012

By A. Y. Senchenko, Y. V. Kulikov

"Different methods aiming at specific energy calculation and design of AG/SAG circuits are used in mining. They include JK DWT/SMC test, SAGDesign test and CWi/RWi/BWi tests. The simplest methods with no secret equations and giving energy required for grinding in kWh/t were proposed by F.?. Bond and J.H. Starkey. D.J. Barratt proposed to use results of CWi/RWi/BWi tests for AG/SAG mill sizing. The present paper gives an alternative for forecast of specific AG/SAG energy. The principle is similar to the theory proposed earlier and consists in cumulative AG/SAG energy calculation using indices of rod and ball grinding (RWi+BWi) without impact crushing index (CWi). Then total energy is divided between two grinding stages using special formulas based on extensive statistical information. The forecast indices of AG/SAG and ball grinding are similar to the SAGDesign testing results. Hereinafter the predicted indices are used for mill sizing of the whole grinding circuit. The method considered in the paper enables prediction of AG/SAG energy based on the test results according to Bond method. The proposed method version was not widely published earlier. The aim of the work was to elaborate cost-effective, reliable and accessible way to determine specific AG/SAG energy. At this stage of method development, it is recommended to use it only for works at preliminary Geometallurgy stage (Scoping, Pre-Feasibility). At design stage the obtained data should be confirmed by appropriate testing using alternative JK DWT/SMC and SAGDesign methods.INTRODUCTIONAppropriate crushing and grinding testing is required to design efficient comminution circuits. It is obviously important to obtain accurate information about ore hardness properties since the main energy consumption at the plant is associated with comminution processes. Moreover, it is required to apply the processes that make it possible to minimize operating costs and efficiently use capacity of the installed equipment installed.When studying ore hardness properties, it is required to take into account that breakage of the material is performed using different equipment. That is why accurate selection of the equipment and the circuit calculation without relevant testworks is impossible. Ideally, the testworks should provide answers to the following questions: determination of ore hardness properties, determination of specific energy consumption for comminution as well as obtaining of sufficient amount of statistically significant results from the tests. The results from crushability and grindability testworks in the first place provide assessment of ore hardness properties and in addition correlate with throughput of the respective equipment. The data obtained can be used for modeling of comminution circuits at the stage of the technology development"

Jan 1, 2016

By A. Bascetin

The mining industry in Turkey has been developing in the last 10 years. Mine wastes and tailings have thus been increasing, depending on the rising production rates. There are many problems related to accidents that occur in tailings damps. In this study, the applicability of the surface paste disposal (SPD) method for a Pb-Zn mine in western Turkey was examined. Density was 3.084 and specific surface area was 0.899 m2/g. The mill tailings have very low plasticity and show characteristics of clays and silts in terms of the Unified Soil Classification System. The particle size distribution of the tailings was 39.2% particles finer than 20 µm. The results of this study showed that the physical and chemical properties of mill tailings make them suitable for SPD.

Aug 1, 2013

By Claudio Rocha Rosales

"Peñoles is a mining group with integrated operations in the smelting and refining of non-ferrous metals, and is also a chemicals producer. Peñoles is the world’s foremost producer of refined silver, metallic bismuth and sodium sulphate and is the leading Latin American producer of refined gold, lead and zinc. The Met-Mex Peñoles Zinc Plant commenced operations in 1973 with an annual production capacity of 105,000 t/y. Year after year the production has been increased, and at present, the production capacity is 240,000 t/y. In this paper, the leaching process,particularly the operation of the jarosite circuit is reviewed ,specifying process improvements to treat high iron calcines.INTRODUCTIONThe purpose of the leaching process is to recover the metals, mainly zinc,through a series of extraction stages with sulphuric acid solutions, which progressively increase the zinc recovery. After the series of acidification stages,the solution, which is rich in iron, is sent to the jarosite circuit to separate the zinc from the iron (Garcia & Valdez, 1996).The first step of the leaching process is the neutral leach circuit which produces a zinc sulphate solution that is sent to the purification section for the removal of impurities such as cadmium, cobalt and copper, after this solution is sent to the tankhouse to feed the electrolytic cells."

Jan 1, 2016

By Michel Fontaine, Bruno St-Cyr

"The mission of the CENTRE DE RECHERCHE INDUSTRIELLE DU QUEBEC (CRIQ) is to stimulate economic development by guiding businesses in their pursuit of innovation.With a comprehensive approach to their needs, CRIQ provides businesses with expertise based on the most recent developments and insights in the fields of:Research and Development ServicesAutomation and production processesDevelopment of industrial equipmentEnvironmental biotechnologiesTesting and Product Qualification Services Industrial and Technological Information ServicesConsultancy and competitive intelligence servicesIndustrial information bankStandardization ServicesElaboration of standards and product certificationSystems registrationEXPERTISE COMPETENCE, INNOVATIONSince its founding in 1969, CRIQ has been involved in over 100,000 projects. The results of its research and development services have enabled it to build over one hundred pieces of equipment, almost all still in operation today. CRIQ has been and remains the driving force of innovation and expertise on the industrial scene, offering highly competitive solutions to a clientele from numerous industrial sectors.CRIQ became a crown corporation operating on a commercial basis on June 30, 1997. This change in its corporate structure has enabled it to put a marked emphasis on trade and implement an array of new operational practices.The formation of marketing companies with private partners, the opening up to corporate business and international markets, the new directions for internal research and the strengthening of its marketing component are among the activities CRIQ has initiated over the last fiscal year to finally reach its cruising speed."

Jan 1, 2000

By Mark Rebagliati, John Payne, Jim Oliver

The Campo Morado precious-metal-bearing, volcanogenic massive sul?de deposits occurin a lower Cretaceous, bimodal, calc-alkaline volcanic sequence in a major northerly trending belt inthe Guerrero Terrane in northeastern Guerrero, Mexico. During upper Cretaceous to Early Tertiary greenschist-facies regional metamorphism, the rocks were deformed strongly into a northeast-verging fold-and-thrust belt. Three later stages of weak deformation were dominated, respectively, by kink folds, broad warps, and extensional faults. Most deposits occur in the upper part of a sequence of felsic ?ows and heterolithic volcanoclastic rocks or at its contact with overlying chert and argillite-sand-stone. The Reforma and El Rey massive sul?de deposits are on the overturned limb of a major, thrusted anticline, and the Naranjo and El Largo massive sul?de deposits are to the south on the upright limb of the same major fold. The La Lucha and San Rafael massive sul?de occurrences are in an upper plate to the southwest which was thrusted over the plate containing the Naranjo and El Largo deposits. In several of the deposits, Au, Ag, Zn, and Pb are concentrated near the stratigraphic top, andCu is concentrated near the stratigraphic base. Major minerals are pyrite, quartz, ankerite, sphalerite,chalcopyrite, and galena. Minor minerals are tennantite-freibergite, arsenopyrite, and pyrrhotite. Goldand Ag occur in argentian gold, and Ag also occurs in tennantite-freibergite. The cumulative inferred resource of massive sul?de for the Reforma, Naranjo, El Rey, and El Largo deposits exceeds 30 Mt, with the latter two deposits incompletely delineated. Underlying pyrite-quartz stockwork zones contain chalcopyrite, chlorite, and sphalerite. Hydrothermal alteration minerals in the stratigraphic foot-wall are pyrite, quartz, chlorite, ferroan dolomite, and ankerite. In the stratigraphic hangingwall, hydrothermal alteration minerals are sericite, calcite-dolomite, and lesser clay minerals and quartz. The deposits belong to a low-sul?dation, volcanogenic massive sul?de system formed in a subaqueous environment, and are of the bimodal, siliciclastic type.

Jan 1, 1997

By D Marshall

The sub-level blasthole benching method of mining has been proved to be economical at Willroy Mines. How-ever due to the nature and attitude of the wall rock, this method is susceptible to serious hanging-wall dilution of the ore. Attempts to solve the dilution problem by various means were not satisfactory until long Stressteel bars were employed as rock bolts. The adoption of this de-vice does not require any special skill, and has become routine in the under-ground operation. Since the inception of this method, the dilution of the ore has been greatly reduced and the ov1!r-all costs of controlling this dilution are much lower. INTRODUCTION T HIS is a report describing the successful use of long Stressteel bars as rock bolts in preventing l1anging-wall failure and consequent dilution in open stopes. Willroy Mines Limited is located (Figure 1) near the town of Manitouwadge, Ontario, approximately l1alf-way between Sault Ste. Marie and Port Arthur.

Jan 1, 1963

The control of AG mills fed by ores with harder and softer components can be challenging due to the sensitivity of the mill to the ratio of hard to soft components. The mills at LKAB?s iron ore operations are generally well controlled, but there are periods when the throughput falls off dramatically, due to a loss of mill filling. As the ore is upgraded in the sorting plant through magnetic separation prior to milling, this presents an opportunity to manipulate the feed blend in advance. In order to assess this opportunity, a fullscale mill charge was dumped and assayed by size to quantify the build-up of competent waste in the mills. This was supplemented by pilot and locked-cycle laboratory tests at a wide range of feed blends in order to facilitate the development of an appropriate multi-component AG mill model. This paper reports the experimental campaign requirements and methodologies, as well as the major outcomes from analysis and modelling exercises using the industrial, pilot and laboratory multi-component data.

Jan 1, 2012