Search Documents

By d&apos, F. Elia

Hot cracking of magnesium (Mg) alloys during welding creates a barrier to enhancing the use of these alloys in automotive applications. As a result, it is imperative to understand the mechanisms responsible for hot cracking of Mg alloy welds in order to develop means of eliminating this problem. In this study, the hot cracking susceptibility of AZ91E and AE42 magnesium alloys were assessed using the moving torch Varestraint test method. Plates of 3 mm thickness were extracted from AZ91E and AE42 ingots and subsequently tested. Quantitative cracking data in terms of maximum crack length (MCL) was used for evaluating the cracking susceptibility. Scanning electron microscopy was carried out. The results suggest that AE42 showed a higher resistance to hot cracking in comparison to the AZ91E alloy. This was attributed to the difference in microstructure between the two alloys. In the fusion zone and HAZ of AE42, the brittle needle-like A1IIRE3 phase was seen to decompose to the more ductile particle-like Al2RE phase, thereby increasing the alloy's resistance to hot cracking. In contrast, SEM fractography revealed that brittle A16Mn and Mg17A112 intermetallic particles segregated to grain boundaries and triggered hot cracking in AZ91E.

Jan 1, 2011

By J. J. O?Neill

Introduction The Beattie mine is the first of its character to be exploited in Quebec. It is primarily a large low-grade gold deposit containing values which a few years ago would not have been considered as ore. Much interest is attached to this development as its success may mean a greatly enlarged scope to gold mining in Canada on deposits which have formerly been considered worthless. Because of its potential importance as a pioneer in low-grade gold mining, the Quebec Bureau of Mines decided to make a careful detailed study of the Beattie in the hope not only of assisting in its development, but of stimulating the search for similar essential geological conditions in other parts of the Province. This paper is a summary of the results obtained during two months on the property in 1932, supplemented by a few trips underground in 1933. The full report will appear in the Annual Report of the Quebec Bureau of Mines for 1932, Part C. Location and Means of Access: The Beattie ore-body is situated two miles west and one half mile north of the centre of Duparquet township, and approximately 22 miles north 28° west of the town of Noranda. Until the fall of 1932, access to the property was from LaSarre, on the Canadian National railway, over a thirty-mile water route with one portage 600 feet long; about 2,000 tons of machinery and supplies were taken in by that route. An automobile road, nine miles long, now connects the property with the Makamik highway, and a narrow-gauge railway, without ballast, gives outlet for concentrates from the mill to the C.N.R. tracks of the Rouyn-Taschereau line, nineteen miles distant.

Jan 1, 1934

By John Starkey

"During the period June 2007 to March 2007, John Starkey of Starkey & Associates (Starkey) worked in Russia for High River Gold, supervising the engineering design work that was being done at the IRGIREDMET Research Institute, in Irkutsk Russia. The work entailed moving the Newmont No. 4 mill from Elko, Nevada to Berezitovy, a mine site north and west of the city of Skovorodino, in the Amur Region of Siberia. This was a grass roots project and required construction of all phases of the infrastructure and process facilities that are associated with a 5000 t/d open pit mine and CIP mill.During the course of this engineering design exercise, many aspects of doing business in Russia were encountered, with regard to laws, norms, and business practices. This paper discusses many of these findings. Also by living in Irkutsk, many observations on Russian life and social customs were made and these merit discussion from a general interest point of view.Prior to going to Russia, another engineering and ore testing firm (TOMS) had approached Starkey to find out if Starkey could assist them in upgrading their SAG ore testing procedures to Western standards in order to offer their clients turnkey projects, that included reliable SAG and AG grinding. TOMS was aware that Starkey had invented the SPI test but did not know that the SAGDesign test had by then been fully developed and was being offered commercially as the most accurate way in the world to design new grinding mills. They were also unaware that this new testing method had been patented by Outokumpu (now Outotec) and that this method allowed them access to a design method, through Starkey, that would lead to a manufacturer’s guarantee (by Outotec) of throughput and grind for any new semi-autogenous or autogenous grinding circuit, with or without ball mills.When Starkey started working at IRGIREDMET in June 2005, they also made a request to add a design method for SAG mills that would be considered acceptable to Western clients. From these requests, presentations were made in Russian to both institutes and each decided to join the SAGDesign Consulting Group as satellite members and buy a SAGDesign test mill to use with their Bond Ball Mill Work Index mills, to provide SAGDesign testing services. To complete the service, contracts have been put in place for Starkey to use these results to design new grinding equipment and to train engineers at TOMS and IRGIREDMET how to do this work.Starkey also undertook to train engineers at both labs to go into the field and to take the samples for SAGDesign testing programs. It is here where the SAGDesign testing service upgrades other grinding test programs because the samples to be used for design are professionally chosen, and the results will be much more likely to produce a satisfactory design. Starkey is a mining engineer and is uniquely qualified to do this task. This and the SAGDesign test are the key components that lead Outotec to offer a performance guarantee for mills designed by Starkey."

Jan 1, 2008

By Sakellariou M., Ferentinou M.

Determination of the nonlinear behavior of multivariate dynamic systems often presents a challenging and demanding task. Therefore, complex geomechanics systems are an ideal area for the application of intelligent methods. Often the physical problem is controlled by nonlinear equations, conveying to the use of neural networks. Hudson, (1992a), aiming at efficient engineering modelling and design, introduced and developed Rock Engineering Systems (RES) approach, through the implementation of generic interaction matrix GIM. This approach has been used for a wide variety of rock engineering and other problems, resulting in many case studies available, which illustrate the application of RES to rock engineering problems. Considering the spectrum of the coding methods for the Generic Interaction Matrix, we suggest an objective coding approach. Among the five proposed coding GIM methods, the coding method according to the slope of Pi and Pj relation is relatively accurate, but it might be difficult or impossible to establish or estimate the exact relation of Pi vs Pj for most of the variables involved within a rock engineering system. Self organising maps, are a special type of unsupervised artificial neural networks, which can learn from complex, multidimensional data, and transform them to visually decipherable clusters. The proposed, coding of the GIM, is performed through the combined use of scatter plots produced through, (SOM), and the coding according Pi vs Pj slope. Naghadehi et al., (2013) constructed a database of worldwide experience, in open-pit mine slope stability, the selection of the principal factors was based on Hudson (1992a) who proposed an ‘atlas’ of factors affecting the stability of rock slopes. Slope classification was performed according to status of stability. The rating of the GIM matrix was completed, coupling scatter matrix produced by SOM training, and Pi vs Pj slope plot. Results refer to the identification of clusters, according to status of stability within the original multivariate data set, and the rating of the principal factors according to the dominance and interaction intensity within the open pit mines RES.

Jan 1, 2015

By Curtiss O. Ehrsam, M. Naseem Mian

Alaska’s Red Dog Mine is strengthening its position within Cominco’s “Vision 2000”strategic plan by continually improving quality and quantity of production while reducing costs. Red Dog has evolved into a stable and mature operation, after six years of milling experience. A high grade, partially oxidized orebody in the severe Arctic environment, along with competing producers in a volatile metals market, are the continuing challenges facing Red Dog. The Red Dog Mine is striving to meet these challenges with emphasis on operator training combined with creative systems development and increased production. This paper describes developments in operations along with future plans.

Jan 1, 1996

By R. H. Sheaphim

THE RECENT and continuing activity in the Boundary district, British Columbia, makes the publication of this paper timely. The following description and discussions are based on two years' experience in the district as Field Manager and Geologist for Attwood Copper Mines, Limited. The Attwood project was organized by Dr. D. F. Kidd to re-examine the Boundary mining camp. Thanks are due to Dr. Kidd, both for his intelligent guidance during the project and for his permission to publish this paper. Much of the data and many of the interpretations presented are credited to the work of, and to discussion with, Dr. W. H. White, Consultant Geologist, who worked for two field seasons on the project. However, the author assumes the responsibility for this presentation. Dr. C. D. A. Dahlstrom worked with the author during the latter stages of the project. His assistance and advice are gratefully acknowledged.

Jan 1, 1956

Overview ?G-9 Discovery Hole 420 drilled May 2005 ?14.16% Zn, 1.76% Cu ?Greenfield discovery built into the G-9 Mine in under 4 years. ?Utilized a unique ?Parallel Track? approach to fast-track mine development. ?Raised over $200million in financing without a Feasibility Study. ?Mine built for $149.7 million, only 20% over PEA. ?Commercial Production declared April 1, 2009. ?G-9 Mine has now completed the first year of commercial production on April 1, 2010. ?Initial cash costs per pound of zinc US$0.39/lb -US$0.45/lb range. ?Mill operating at over1,900 tpd in March 2010, well above design capacity (1,500tpd) only one year after starting commercial production. ?Balance Sheet -$167 million assets, $24 million long-term debt, $22 million cash. ?Restarted Exploration ?excellent initial results. ?Strategically positioning Farallon to grow to a mid-tier mining company.

May 1, 2010

By R. C. Rowe

THIS paper is an endeavour to analyse the ideal and practical functions of government technical mining services, and their relationship to the National Domain, as well as to one another. its spirit is not critical, even though at times it may appear to besoin fact. It is a serious effort to divert a trend in public thought which delights in calling itself practical whereas it is really merely short-sighted. The author refers particularly to the idea that governmental research is a luxury which should be curtailed in the interests of economy, and turned over to private enterprise or the provinces. In order that we obtain the proper perspective of the question, it is advisable to indulge in a little history. In the year 1842, the Geological Survey of Canada was formed under the guidance of William (later Sir William) Edmund Logan. The literature on the founding and history of the Geological Survey of Canada is extensive, and therefore it is unnecessary to go into detail here regarding it. It might be mentioned, however, that the Geological Survey of Canada is only seven years younger than the Geological Survey of Great Britain (founded in 1835), and is only exceeded in age on the American continent by the State Geological Surveys of New York, Pennsylvania, Massachusetts, and Michigan, which were founded between 1833 and 1836. In 1877, the Geological Survey became a permanent government institution as a branch of the Department of the Interior. It should be noted, however, that the Director of the Survey ranked as a Deputy Minister and reported direct to the Minister. This continued until 1907. In 1886, the Mineral Resources and Statistics Division of the Geological Survey was formed. Some years later, the Canadian Institute of Mining and Metallurgy (then the Canadian Mining Institute), backed by the mining press, began to agitate for the establishment of a Dominion Department of Mines, and in 1907 such a department was founded by the Geology and Mines Act of that year, with a separate Cabinet portfolio for the position of Minister of Mines.

Jan 1, 1939

Flotation works very well for particles that are typically in the range 20 to 150 µmin diameter, for base metal ores. In this range, it is possible to get quite high recoveries in conventional flotation machines. Outside this range, the recoveries decline progressively, whether it be with the very fine or the coarse end of the size spectrum. In this paper, the reasons for the drop-off in recovery are briefly reviewed, together with strategies for future work. Recent progress in the author's laboratory will be described. These include the Concorde Cell, which takes advantage of the high dissipation rates in the shock wave created when a gas-liquid mixture reaches supersonic velocities. The environment thus created is very beneficial for the flotation of ultrafines. For coarse particles, the reasons for the drop-off in recovery can be related to the highly turbulent nature of the pulp in a conventional flotation cell. To improve recovery, it is necessary to find a way of bringing particles and bubbles into contact in a quiescent environment. A new process for coarse particle flotation will be described, in which a fluidized bed is created in the flotation cell. The flow conditions are very gentle, and the high solids concentration leads to rapid rates of capture of the particles. Experimental results are presented. It is apparent that the maximum floatable size for coal and minerals can be increased by a factor often over the limits found in current practice. Advances

Jan 1, 2009

By H. Agnerian

"A survey of 925 mineral property transactions worldwide was carried out between 1987 and 2004. These mineral properties with reported Mineral Resources include 457 gold properties, 322 base metal properties, and five platinum group element (PGE) properties. Based on constant Canadian dollars, the results of the survey indicate that:• In general, unit metal values in the ground (e.g. $/oz Au or $/lb Cu) have kept pace with the changes in the respective metal prices during the period of the survey.• A general decrease in unit gold values in the ground has occurred from about $57/oz Au in 1987 to about $11/oz Au in 2002 for Canadian mineral properties, with the exception of a peak of $58/oz Au in 1996.• A similar trend for mineral properties has occurred in the United States, but with lower unit values, in the range from $1/oz Au to $10/oz Au during the last three years of the survey. • Unit metal values in the ground for gold properties in Canada were higher than for those in the rest of the world.• Unit metal values in the ground for copper properties in Canada were in the mid-range compared with other countries in the rest of the world; the United States and Australia were higher and Latin America, Asia, Africa, and Europe were lower than in Canada.• Unit metal values in the ground for zinc properties in Canada were also in the mid-range compared with other countries in the rest of the world; Latin America and Europe were higher and the United States, Australia, and Asia were lower than in Canada.• Unit metal values for nickel properties in Canada were highest compared with other countries in the rest of the world, followed by the United States, Australia, Africa, and Asia.• Gold values in the ground in Canada have ranged from 6% to 14% (with an average of approximately 10%) of the gold price.• The unit values of base metals in the ground have been in the order of 2% of the quoted metal price, during the period of the survey."

Jan 1, 2006

By Martin Froehling, Curtis Mohns, Rahim Rajwani, Michael Fullam

"The Kemess mining and milling complex is operated by Northgate Minerals Corporation and is located in the mountains of north-central British Columbia, 430 kilometers northwest of Prince George. The complex consists of the Kemess South open pit mine and a 52,000 tonnes per day mill. Hypogene, supergene and leach cap ores are processed using conventional crushing, grinding, and flotation techniques to produce gold-copper concentrates with minor by-product silver value.The rougher flotation concentrate is re-ground in closed circuit before being cleaned to final concentrate grade. Historically, gold losses in the cleaner tailings were primarily associated with pyrite, with only minor amounts of free gold. More recently, with the processing of high pyrite ores, the major losses were found to be free gold less than 10 microns in size. The fine grind required for the high pyrite ores resulted in over-grinding of the free gold particles in the regrind circuit, contributing to poor flotation characteristics. It was thought that if this free gold could be recovered by gravity at coarser size in the regrind circulating load, the free gold losses in the cleaner tailings could be reduced.Preliminary test work carried out by Knelson Gravity Solutions indicated the potential for free gold recovery in the regrind circuit. A Knelson XD-30 Concentrator was installed with variable speed capability, and a series of optimization tests were carried out. In addition, cleaner tailings were characterized with gravity operating and with gravity not operating to determine the overall gold recovery benefit. The single Knelson XD-30 installation recovers ~10% of the total gold in the regrind circuit and increases overall recovery by 3% when high pyrite ores are processed."

Jan 1, 2007

By Roxanne Scott

Outline ? Overview of Community Investment in the Mining Sector ? Emerging Good Practice: ?Strategic Integrated Community Investment? ? Assessing Local Context: ? Institutional Assessment ? Partnership Assessment Approaches to Community Investment Isolation: No proactive engagement in community development Ad hoc philanthropy: small infrastructure, sponsorships, donations Strategic philanthropy: Community proposes options for development Company decides what to do and carries it out, e.g. building schools, health posts, roads Strategic integrated community investment: ? Aligned with government/community development goals and priorities ? Communities and government involved in decisions and execution ? Focused on training and capacity building ? Partnerships ? Continuation in absence of company support Measured returns on investment

May 1, 2010

By F. McCarthy, R. McDonald, G. Woodbridge, G. Brock, D. Robinson

"The Direct Nickel process is a hydrometallurgical technology being developed to treat nickel laterite ores by leaching at atmospheric pressure. The leaching process uses nitric acid in a relatively large excess, is thus non-selective, and much of the soluble iron goes into solution. The first stage of solution purification is iron hydrolysis and the Direct Nickel process utilises the colligative properties of the pregnant leach solution (PLS) to enable the removal nitric acid of varying concentrations via distillation. Once sufficient acid has been removed, the boiling point of the solution is increased allowing high temperatures (up to ~170°C) to be achieved under atmospheric pressure. The higher temperatures initiate the precipitation of the iron primarily as hematite and allow the removal of the acid generated by the hydrolysis reaction. The rejection of the iron is near complete with solution tenors typically falling from 65 g/L Fe, or more, to less than 50 mg/L Fe. The separation of clean nitric acid from the PLS at this stage allows for relatively simple acid recycling. A hematite product with iron content above 60% could also provide an extra revenue stream.INTRODUCTION The Direct Nickel (DNi) Process is a novel hydrometallurgical processing route designed to treat all types of nickel laterite ores in a single flow sheet using nitric acid under atmospheric conditions. A simplified flow sheet is shown in Figure 1.Between 2007 and 2012 the process was developed and refined at Direct Nickel’s laboratory within the CSIRO Minerals’ facilities in Perth, Australia, and in 2013 a series of pilot plant trials were run under continuous operating conditions. The process is designed to treat both limonite and saprolite in the same flow sheet, and after comminution, the blended ore is mixed with nitric acid and leached just below boiling point in agitated atmospheric leach tanks. The acid is added in excess, so typically for a blend of limonite and saprolite the acid addition can be in the order of 1.8-2.0 t acid/t dry ore. After a residence time of between 4-6 hours the majority of the soluble metals have leached into solution and the insoluble leach residue is separated from the pregnant leach solution (PLS) via counter-current decantation."

Jan 1, 2016

By T. Bednarski, T. McCallum, L. Moya, L. Nsenga, B. Mbao

The accumulation of solids in solvent extraction (SX) circuits can cause problems with the physical and economic performance of the operation. These solids are responsible for the formation of crud, a solid stabilized emulsion containing organic, aqueous, air, and fine solid particles. The build-up of crud in SX settlers can limit SX operation throughput, require plant downtime, lead to higher organic losses, or result in higher aqueous in organic entrainment (all of which can have a significant, negative economic impact). Current practices for crud management are typically reactive. Crud is physically removed after it has been allowed to build to excessive levels in the circuit and processed mechanically using centrifuges or filtration. A new proactive solution has been developed to prevent crud formation and build-up. Low ppm dosage of an additive, ACORGA® CR60, into the pregnant leach solution (PLS) has resulted in reduced crud formation in pilot and commercial scale for a variety of PLS streams. This paper will review results from operations in North America and Africa, covering heap leach, concentrate leach, and agitated leach feeds. INTRODUCTION Crud formation and build-up in solvent extraction (SX) circuits has been a long time topic discussed and claimed to be crucial to the whole hydrometallurgical process (Liu, et al, 2006). Crud formation is present in all SX systems be it copper, uranium, zinc, etc., and Ritcey (1980) defined crud as a stabilized emulsion containing organic, aqueous, and fine solid particles. The ore type and feed composition is a major determining factor of crud formation and typically contains Si, Al, Fe, P, and sulfates (Ritcey, 1980). It typically builds at the interface between the organic and aqueous, but can also be observed as floating crud on the surface of the settler, or bottom crud, which is common to find in circuits treating agitated leach feeds such as in Africa. As crud formation has been unavoidable, many of the current crud management techniques are reactive, allowing crud to form and build in SX circuits. Once it does, it is removed and treated via different mechanical techniques, typically through some type of filtration or three-phase centrifuge, to remove the solids and recover the organic phase trapped within the emulsion (Ritcey, 1980). Automated pumping systems have also been designed and are frequently used in North American operations. The time and capital required to react to crud formation can be an overwhelming aspect to SX operation.

Jan 1, 2019

By William Hawker, James Vaughan, Jeff Chen, Antony van der Ent

"Nickel agromining utilizes hyperaccumulator plants (“metal crops”) to extract nickel from low-grade soils, a process that yields high-grade nickel bio-ore. This feedstock is further processed into a range of nickel products. The bio-ore is relatively free of impurities that complicate the traditional processing of laterite nickel ores. In this paper, current primary nickel processing routes and proposed nickel bio-ore processing options are summarised. A novel pyro-hydrometallurgical route demonstrated at the laboratory scale is described. This process produces a precipitated nickel hydroxide product and takes advantage of the water-soluble basic compounds in the ash to minimise reagent requirements, thereby making it suitable for small-scale implementation in close proximity to the nickel farm. In this process, nickel is precipitated from the leach solution using the basic ash wash liquor. Leaching nickel from ash generated from open air burning requires strong acid and long residence times to obtain high recoveries due to its complex nature and distribution of nickel in multiple phases. This process can be improved by optimising the ashing process with respect to nickel leachability.INTRODUCTIONHyperaccumulator plants have the unique capacity to ‘biopurify’ and concentrate certain trace elements (e.g. nickel) from the soil into their biomass (Reeves 2003; van der Ent et al., 2015). Cultivating these plants as ‘metal crops’ by periodically harvesting and incinerating their biomass generates a high-grade bio-ore (Chaney et al. 1998; Li et al. 2003). This process is called phytomining or ‘agromining’ which is an emerging technology for extracting nickel from sub-economic resources (van der Ent et al., 2015). Potential near-term applications of the technology include implementation on land ahead of processing of the underlying ore-body (Willis 2015), as a mine-site rehabilitation strategy or as an alternative crop for farmers on land that is not suitable for normal food crops. In the longer term, nickel agromining could provide a significant supplement to the nickel supply chain. Critical to the success of agromining is effective bio-ore processing. Due to the unique chemical composition of this feedstock material, existing processes are not very efficient. Our current research efforts aim to develop new process options that overcome limitations of previously trialled routes. In this paper we summarise conventional nickel process routes and proposed new options for producing agromined nickel."

Jan 1, 2016

By W. L. Brown

"The Normetal mine is about 7 miles east of the Ontario-Quebec boundary, and 13 miles north of the town of Dupuy on the Canadian National railway. The mine workings are largely on lots 44 and 45 in the south half of range 10, Desmeloizes township.The surface outcrop is reported to have been discovered by a trapper previous to 1925, but the details are obscure. The property was originally owned by the Canadian Exploration Company of Amos, Quebec, and was later transferred to Abana Mines, Limited. The latter Company carried out underground work from two shafts down to the 550-foot level. The property was acquired by Normetal Mining Corporation in 1931 and was reopened in 1933, when development work was carried down to the 800-foot level. The mine was closed down in 1935 because metal prices did not justify production at that time. It was reopened early in 1937 and milling commenced in September of that year. To the end of 1945, a total of 1,497,- 169 tons of ore was milled from which was produced 184,533 tons of copper concentrates containing 84,738,368 lb. copper, 2,744,100 oz. silver, 26,230 oz. gold, and 153,524 tons of zinc concentrates containing 163,752,433 lb . zinc."

Jan 1, 1954

By T. Banerjee, D. Felsher, G. Leavoy

"Lake Shore Gold is engaged in commercial gold production at both the Timmins West and Bell Creek mines, located in Timmins, Ontario. Run of mine ore is processed at the Bell Creek mill which consists of a conventional gold mill flow sheet involving crushing, grinding, gravity concentration and carbon-in-leach (CIL) for gold recovery. Since 2009, the operating capacity of the mill has been upgraded from 2000 tpd tonnes per day (tpd) to over 3,000 tpd. The most recent expansion involved the installation of a low aspect ratio SAG mill to replace the secondary crusher. Without operational data on the low aspect mill, combined with a site team that was new to SAG milling, there were many challenges in achieving the target throughput from the circuit. Through the implementation of AwaRE advanced controllers, running in closed loop with PRC fragmentation cameras as well as embedded PARC modules within the Allen Bradley PLC, the site was able to rapidly develop a best operating practise and has been successful in creating a stable and consistent operational environment. The process, lessons learned and eventual solution will be reviewed in this paper.INTRODUCTIONLake Shore Gold is engaged in commercial gold production at both the Timmins West and Bell Creek mines, located in Timmins, Ontario. Run of mine ore is processed at the Bell Creek mill which consists of a conventional gold mill flow sheet involving crushing, grinding, gravity concentration and carbon-in-leach (CIL) for gold recovery. Since 2009, the operating capacity of the mill has been upgraded from 2,000 tpd tonnes per day (tpd) to 3,150 tpd. The most recent expansion involved the installation of a low aspect ratio SAG mill to replace the secondary crusher. This endeavor was split into two phases: the expansion of the back-end (Phase 1) and the front-end (Phase 2) of the mill. Phase 1 of the expansion was completed at the end of 2012 and involved enhancements and capacity addition to the leaching and adsorption circuits, which increased the mill’s capacity to 2,500 tpd. Phase 2 of the expansion commenced at the end of July 2013 and involved the expansion of the crushing and grinding circuits. The expanded front-end of the mill now has a capacity of 5,500 tpd, and processes ore from both Bell Creek and Timmins West mines. The updated flow-sheet, as shown in Figure 1, illustrates the replacement of the two-stage crushing and ball milling circuit with a single stage crusher and a low aspect ratio SAG mill."

Jan 1, 2015

By Waldbillig. D.

A baseline of the poisoning effect of hydrogen sulfide (H2S) fuel impurities on solid oxide fuel cell (SOFC) anodes was developed using polarization testing. After the baseline behaviour was characterized, tests to study the effect of various H2S concentrations on the rate and amount of cell voltage degradation and recovery were performed. Attempts were made to improve the rate and amount of recovery by various methods. Testing was very reproducible, but significant electrochemical performance degradation was seen after all H2S poisoning tests even at an H2S concentration of 0.1 ppm. Degradation is initially quite rapid, but after a period of time the rate of degradation levels off. After poisoning was complete, the H2S flow was stopped and the cells were allowed to recover. Some recovery was seen after poisoning, but cell performance was never fully recovered.

Jan 1, 2005

By Luis R. Fonseca, C. Raimat, C. Wendeler, A. Sanz

"Rockfall barriers are widely known as proven efficiency element to protect infrastructure by catching the rock blocks in the falling direction and absorbing the energy generated by them.It’s common in the project design phase and during installation, fix rockfall barriers for catch a high percentage of the falling blocks and in many cases consider as valid the solution when the barrier can capture all of them. However, in many cases it’s possible to consider the use of these protections, simply to guarantee a secure shed for the traffic and intercept simply the blocks that theoretically hit the road surface.The results of the high-energy rockfall protection barriers type GBE which protect GC-200 road in Las Palmas de Gran Canaria are shown in this paper.The topographic data should be especially detailed observed and even more if you want to apply the technique of ""shadow zone"" with a flexible gallery system. It should be drawn from detailed topographic maps and drawings (photogrammetric restitution) to the scales 1/1000, 1/500, or 1/200; and it is important not to ignore the presence of vertical cuts, tracks, small slopes that modify the trajectories (trampoline effect, hard points that favor the rebounds) and which are not always presented in the drawings.The ""shadow zone"" is defined as the protected area, located at a lower elevation to the line created by the rockfall barrier to except of trajectories of rocks and free from the influence of the deflection of the system under the maximum energy level for which it was designed (MEL)."

Jan 1, 2015

By John O. Galloway

"The year 1947 was a momentous one in the history of the petroleum industry in Canada. It was in that year that Imperial Oil Limited made its discovery at Leduc, the forerunner of other discoveries, large and small, and the spark wl1ich started a most intensive exploration and development programme there.If, to use boxing parlance, Leduc was the first blow of a one-two combination which left doubting Thomases groggy, then Redwater was the number two blow which achieved the knockout. The oil industry's exploration leaders did about-face without delay and the rush of oil operators of all classifications to western Canada began. It is still continuing, and the influx of capital which the operators have brought in and are bringing in has a bouyant effect upon the over-all economy. The boom is on, but it is a sound one, and it is difficult to conceive that it will have anything but the most beneficial effect on Canada, and particularly western Canada.The petroleum industry is an important segment of the general economy. Its activities call for tremendous amounts of capital; its employees are well paid; it is a large customer for a wide range of products of other industries; its commodities are essential to the citizens and the nation.The industry is carried on by highly aggressive and independent groups and individuals, of which a small minority are integrated while the majority are relatively small operators engaged in only one or two phases of the business. Competition is the rule and, since the nature of the business is mass production, the industry is faced from time to time with serious problems, many of which are peculiar to it."

Jan 1, 1950