Search Documents

By H. L. Cameron

Introduction Since the beginning of gold mining in Nova Scotia in the year 1860, the biggest problem o the mine operators has been to find and follow the ore zones in the narrow quartz veins. It was early recognized that all veins were not gold bearing and that, in those that were, the commercial ore was confined to limited zones. A large number of geologists and mining engineers have been interested enough to give time and thought to the problem, but, until the last four or five years preceding World War II, they were handicapped by lack of exact data from mining operations. The necessary data could only be obtained by daily checking of underground operations. Such daily checks were instituted at a number of mines during the period 1935-40 and, in every case, were successful in delimiting the ore zone or zones for the particular mine. The present paper deals with the results of this work as applied to practical ore finding. It is an attempt at extrapolation, from observations in the four districts with which the writer is personally familiar, co other districts in which similar conditions or structures are reported.

Jan 1, 1947

By M. Mirzazadeh

Air cooled crackable and conventional forged steel specimens were tested under reversed push-pull conditions to examine the effect of shot-peening on their high cycle fatigue behaviour (-106 cycles). The steels were tested in the normalized as well as shot-peened conditions. The results showed that shot-peening smooth specimens had little effect on the fatigue limit of the air cooled forged steels and the detrimental effect of the rougher peened surface was not apparent. Microhardness profiles indicated that the shot peening produced a gradient of compressive residual stresses that was greater than that of the loading stresses, suppressing the anticipated beneficial effect on fatigue life. Crack initiation was more likely to occur below the surface. The results indicate that the surface roughness was not a significant factor in controlling the fatigue lives, since they were essentially the same for the non shot-peened and shot-peened steels.

Jan 1, 2010

By D. L. Mckay

"Texasgulf's 25-foot-diameter Kidd Creek No. 2 Shaft is situated next to the company's No .1 Shaft, so that both shafts can share common surface and underground facilities. Shaft construction, covering a span of five years from collaring to commissioning , started by freezing the 50 feet of grey varved clay covering the bedrock. After first completing the concrete headframe, sinking to the 5/00-foot horizon utilized two different shaft construction methods. The top 2800 feet was excavated by slashing a 6-foot-diameter borehole and hoisting the broken material up the 3OO0-foot-deep No.1 Shaft; the remaining 2300 feet was excavated by conventional benching methods. Prior to installing the 5100 tons of galvanized shaft steel on the completion of the sinking operation, the sinker was able to install all thirteen armoured electrical cables in one pass with his modified galloway stage. All loading and lip pockets were installed along with the steel guides and bun tons during the equipping operation.IntroductionOn November 21,1978, Texasgulf completed the No.2 Shaft at Kidd Creek Mine. This shaft is the largest shaft (volumewise) in North America and is unique in many respects . The purpose of this paper is to outline some of the unique features of this shaft as well as to record how this facility was constructed.Soon after sinking No.1 Shaft, Texasgulf started a program of exploratory diamond drilling from the 2800 level in No. 1 Mine. The drilling outlined sufficient ore below that level to justify a second mine. Feasibility studies demonstrated that production could be increased by one-third exclusively from this deep ore . The study called for a 25-foot-diameter shaft to the 5100-foot horizon to service a mine producing 5,000 tons of ore per working day.The site chosen for No.2 Shaft and head frame is 350 feet southwest of No.1 Shaft. This, along with No.1 Shaft, will be away from the influence of ground subsidence when mining at depth. The collar and head frame foundations are located on a flat rock ledge some 70 feet below surface. This flat ledge was found by test holing through the overburden by diamond drilling. It is fortunate that this location best satisfied the surface layout and logistics for both surface and underground ore and waste handling."

Jan 1, 1981

By Jerry M. Whiting, Neil J. Duncan

"Does Canada need a mining industry? Isn't it a chronically depressed collection of businesses that pollute the air and water and tear up the countryside? Wouldn't it be better if Canada's investors devoted their attention to high-technology endeavours, tourism, and other relatively pleasant tasks?Probably the answer to whether Canada needs a mining industry in the 21st century is to look at the real mining industry that is in operation today. The facts indicate that mining is a very important contributor to Canada. It has certainly encountered some challenging times during periods of recession, and it face s severe and continuing problems of cost and competition in world markets. However, uneconomic mines have been closed, others suspended, and productivity has risen dramatically with employment at 77 000, down from 101 000 in 1981. The country's metal and non-metal mines, metallurgical plants and semi-fabricated metals industries employed an estimated 378000 workers in 1986, and paid wages than any other sector of the Canadian economy. This effort resulted in the production of 60 different metals, non-metals and structural minerals valued at $13.5 billion.The trade aspects of the mining industry are of paramount importance. If there is a reason for this situation to change during the next century. it eludes the authors. Canada has the well-developed expertise to discover, evaluate, develop, operate and profit from existing and new businesses based in an enormous area endowed with a nearly unbelievable variety of mineral resources. Many countries throughout the world must rely on producers like Canada, if they are to maintain and/or improve their standard of living."

Jan 1, 1988

"A method is described for determining the viability of hard rock orebody extraction by block caving. Using a very limited amount of geotechnical data, the procedure enhances Laubscher’s empirical stability graph method by using the complex structural modelling system (ChaSM) to assess cavability and block cave tonnages.IntroductionIn considering the selection of suitable mining methods, block caving has gained popularity over other extraction systems in recent years (Butcher, 1999). This has been ascribed to the fact that block caving is the lowest cost per ton mining method, with orebodies that were in the past considered unsuitable for caving, now being successfully mined. However, even though all orebodies will cave, a problem exists in the evaluation of economic viability — it is necessary to be able to predict both when the orebody will cave and what will be the sizes of the initial ore fragments (and the associated tonnages) that report to the drawpoints. This problem is compounded by the fact that, during the scoping study phase of a project, only limited geotechnical data may exist on which to base an assessment of whether block caving is viable or not. Empirical and numerical methods of cavability assessment do not account for the full effects of geological discontinuity trace lengths, nor for the stress regime. Those require significant geotechnical data to be available. The result is that uncertainty may exist as to whether block caving is an economic option. This uncertainty is complicated by the fact that limited experience exists with the caving of more competent orebodies.This paper describes a method for assessing cavability, and for predicting the size of initial ore fragments and the tonnages reporting to block cave drawpoints, using only the level of data normally available during a scoping study. Fragment size and tonnages are assessed by identifying potentially unstable blocks and wedges in the undercut back using statistical joint data. The effects of lateral confining stresses are accounted for by comparing the in situ stress orientations with the joint orientations. To evaluate the accuracy of the method, a back analysis exercise was conducted to predict cavability and initial tonnage for a mine in which the actual behaviour is known. The method is then applied to cavability and tonnage predictions for a hard rock orebody."

Jan 1, 2002

By D W. MacFadgen

THE operating advantages of the longwall retreating system of mining, as opposed to longwall advancing, have been well known for many years. Although retreat walls have been successfully worked in the past in some of the collieries of the Dominion Steel and Coal Corporation in the Sydney, Picton and Cumberland areas, the adoption of longwaIl retreating as the general sys-tem of mining has not been attractive in the Sydney field, due to the time and expenditures required to drive roadways to the boundary. In addition. difficulties in maintaining effective ventilation on the faces, especially under conditions of low barometer, have made the operators in the field hesitant to adopt this as the general system of mining. The development of a machine capable of rapid entry drivage has made possible the driving of the necessary road ways to the boundary at a moderate cost, completely changing the picture and making a retreat system more attractive.

Jan 1, 1961

By Takanori Kokubo, Kenta Suzuki, Tomohiro Sasaki, Toshiya Anami

"Previous work has shown that the strengthening Al-Mn alloys with copper leads to the formation of an undesirable reduction in recrystallized grain size. In this study the mechanisms of strengthening and recrystallization behavior in a continuously cast automotive heat exchanger fin stockof Al-1.1wt%Mn-0.5wt%Fe-0.3wt%Si with a0.3wt%Cu addition were investigated. Metallurgical analysis revealed that the Cu strengthening was dominated by the formation of dispersoid particles, while solid solution strengthening decreased with the Cu additions. This result is attributed to the decrease in the amount of Mn solid solution. The post brazing recrystallized grain size was reduced compared to that not containing Cu. It is postulated that the Cu addition leads to a decrease in the amount of Mn in solid solution which leads to a finer grain size. This effect is attributed to Mn in the aluminum matrix inhibiting boundary migration but allowing other grains to grow during heat treatment. The results are rationalized based on particle stimulated nucleation (PSN), wherein dispersoid particles are more likely to become active recrystallization nuclei during the heat treatment. The increase in the number of active dispersoid particles with Cu addition is correlated to the recrystallized grain structure.INTRODUCTIONImprovements in properties such as strength, braze ability and corrosion resistance in thermal fin stock alloys are all means to gain improved efficiency in heat exchangers particularly in automotive applications. While Al-Mn alloys dominate automotive heat exchanger fin stock alloy, even small chemical compositional changes can profoundly influence these properties (Kawaharaet al., 2004; Yoshino et al., 2009). The microstructure (particularly the grain size and shape) also plays a key role in determining the product performance and hence the thermo-mechanical processing (TMP) must also be considered. The casting method (typically conventional direct chill, DC, or continuous casting) significantly influences the properties in no small part due to the very different TMP routes that are used. Continuous casting is generally favored for fin stock applications as its higher cooling rate (which can be 2 to 3 orders of magnitude higher than DC casting) leads to finer as-solidified intermetallic particles and an increase in super-saturated solid solution elements (such as Mn)that are known to improve fin stock performance such as strength, braze ability(Okiet al., 2008)."

Jan 1, 2018

By Pierre Roy, Claude Gosselin, Maryam Sadeghi, Michel Bourassa, Christian Rochefort, Claude Bazin, Gautier Mahieu, François Lavoie, Marilène Renaud, David Cataford

"Spirals are gravity concentrators used for the concentration of iron oxide minerals from ores. This paper presents the mineral size recovery curves observed for spirals operating in two Canadian iron ore processing plants. The size recovery curves are presented for rougher, cleaner and re-cleaner spirals. The partition curves observed for the spirals are significantly different than those observed for typical gravity concentration devices such as hydrocyclones or hydraulic classifiers. The size recovery curves show the complex behaviour of the minerals as they flow down a spiral and are analysed with a view toward process modelling and simulation. Initial simulation results show that gains in the iron recovery can be achieved by increasing the recovery of coarse iron oxide particles in the rougher spirals.INTRODUCTION Spiral concentrators are gravity based separation devices used for the preparation of coal, iron and different heavy minerals ores (Wills, 1992). The classification of the particles in spirals is based on the combination of gravity, centrifuge, drag, lift and Bagnold forces (Atasoy and Spottiswood, 1995; Burt, 1984; Bouchard, 2001). Several papers are dedicated to the analysis of the forces acting on the particles flowing down a spiral (Das and al., 2007; Sivamohan and Forssberg, 1985; Holland-Batt and Holtham, 1991; Holtham , 1992). Most of these papers aim at the development of a general model for the simulation of the classification of the particles for coal ore processing. Few papers deal with the operation of spirals for processing iron ores (Hyma and Meech, 1989; Srivastava, 2001; Dallaire et al., 1978) and fewer papers present results for spirals used as cleaners following a rougher stage. Since the classification in spiral classifiers is dependent on the particle size and specific gravity a partition or performance curve commonly applied to classifiers (Mai Manga et al., 2012) is used here to analyse spiral operation. Few papers were found to describe the operation of spirals in terms of partition curves (Atasoy and Spottiswood, 1995; Holland-Batt and Holtham, 1991; Richards et al., 2000). Most of the investigations presented the application of a model to simulate the position of coal particles of various sizes and specific gravities along the trough of a spiral (Kapur et al., 1996; Holland-Batt and Holtham, 1991). In addition most of the available literature on spirals deals with one stage of concentration by spirals (Dallaire et al., 1978; Das and al., 2007; Sivamohan and Forssberg, 1985) while industrial circuits usually consist of rougher and cleaner spirals."

Jan 1, 2014

By M. A. Kessick

Current treatment and disposal procedures are compared for clay slimes resulting from the extraction of Alberta oil sands, the extraction of Florida phosphate matrix, the recovery of diamonds from kimberlite deposits in South Africa, the recovery of kaolin from clay deposits in southwest England and the upgrading of bauxite ore. Published research in the area is reviewed, and common trends which are emerging in the disposal of clay slimes are discussed.

Jan 1, 1978

By Eugen Gluck, Gus Van Weert, Peter Kondos

"Microwaves have the capability to heat up sulphides, especially clusters of particles of approx. 1 mm. Some sulphides absorb microwaves more readily than others. Molybdenite is especially effective in this regard, possibly due to its flaky nature and/or electrical conductivity. Even where it occurs in low concentrations in a deposit, individual rocks may be ore grade due to the high monetary value of MoS2. Such rocks often result from crushing mined veinlets or stockwork, or are contained in the cutoff grade fraction of ROM. Machine segregation of rocks high in MoS2 by infrared sensors after microwaving could therefore advantageously be used to upgrade lower grade ore between Mine and Mill. This would reduce the size of the latter, and thus its CAPEX and OPEX. Such upgrading could also yield shipping ore for a distant Mill, or extend ore reserves.Barrick Gold Corp. has been supporting the development of MW/IR sulphide sorting for the past three years. The results of MW/IR sorting work on molybdenite and other (pyritic) ore samples from a variety of sources are being presented here.INTRODUCTIONThis paper looks at mechanized, i.e. machine ore sorting technologies currently available and under development, and what conditions would be needed for the potential application of such ore sorting to sulphide mining and milling. Current machine sorting involves no-contact sensing technology for rocks, and signal processing after sensing to activate airblast segregation of certain rocks, normally the smallest mass to keep compressed air costs down.The forerunner of modern sorting is probably magnetic separation, which utilizes an inherent property of certain ores to divert it into mag and non-mags fractions. Radiometric ore sorters, which have been applied successfully for decades in the pre-concentration of uranium ores (Wotruba and Riedel, 2006) initiated modern sorting. In the 90’s, sensor-based machine sorting became a viable means of increasing the overall economic recovery of a resource. This technology became driven by the availability of low cost computing equipment and the concurrent development of algorithms, and by the availability of extremely fast response sensors and air actuators, allowing the sorting equipment to run faster, dropping the cost per tonne. It has been in industrial minerals processing that rock sorting has been most widely adopted, not really surprising. Liberation occurs on a different scale than in the base metal industry. Most industrial minerals are mined from massive deposits, requiring (in the past) no upgrading. Many of these operations now run into product contamination problems, which ore sorting can solve. One illustration: in Finland, a quarry is separating limestone from dolomite at 500 tonnes / hour, with individual rocks weighing up to 15 kg. Many of these industrial minerals operations have stockpiles of earlier discarded below-quality rocks, now being reprocessed with the help of ore sorting. The economics of this are very favourable, going from zero or negative value (stockpiles can not be left when closing the mine) to full product value for at least a portion of the stockpile. This suggests that in the future the economics of overburden sorting could become attractive under the right circumstances and such treatment could well become an integral part of open pit mine development."

Jan 1, 2009

By S. Caron

From the early 70?s, ?Centre de Recherche Minérale? (CRM) has conducted and co-ordinated Research and Development activities for the mineralurgical and metallurgical industries. Since 1999, CRM has continued its mandate through COREM which is a consortium of 13 members that uses the benefits and advantages of collaborative pre-competitive industry / university research. In particular, COREM?s ?In-Situ Optimization Group? is involved in the implementation of modern optimization and control tools. The POP Project was launched in order to increase and consolidate the use of modern optimization and control tools and methods for mineralurgical and metallurgical processes. To ensure a successful transfer in the industry, there are a number of essential activities that have to be undertaken. These activities have been identified by COREM?s members and are grouped into three main modules: - R&D Module: Research and Development in universities, research centres and other partners; - Technology Transfer Module: integration of new tools and methods into the POP Software, industrial applications and technical support; - Training Module: education of new engineers in universities, continuing education of plant personnel through on-site workshops and resource networking by specific information exchange tools. This paper outlines the opportunities that led to the definition of the POP Project and describes its main modules. The main features of the POP Software are presented, the first application is described and finally, future developments are discussed.

May 1, 2001

By N. A. Duke, R. L. Carpenter

Abstract - The West Meliadine area is underlain by structurally interleaved panels of mafic and minor ultramafic metavolcanic rocks and metasedimentary rocks that occur along the northern margin of the Neoarchean Rankin Inlet greenstone belt. Three structural and metamorphic domains are recognized: (1) the easterly Wesmeg domain; (2) the central Barracuda-Ridge domain; and (3) the westerly Peter Lake domain. The Wesmeg domain is characterized by a series of southeast-trending, north-dipping, foliation-parallel panels of greenschist facies mafic metavolcanic and metasedimentary rocks. The Barracuda-Ridge domain is comprised of greenschist to amphibolite facies mafic metavolcanic rocks that define an east-northeast-trending structural grain. The Peter Lake domain consists of amphibolite facies mafic metavolcanic rocks and minor metasedimentary rocks intruded by a monzonite pluton. West Meliadine hosts the economically significant Wesmeg gold deposits, as well as other important gold showings across the Barracuda-Ridge and Peter Lake domains. The geological setting of the Wesmeg gold deposits resembles that of a break or fault zone. The Pyke Break is a major geophysical discontinuity (>65-km strike length) and is the first-order structural control on gold mineralization at West Meliadine. It is several kilometers wide and characterized by polyphase deformation and shear zone development accompanied by lode-gold mineralization. In general, gold concentration is related to quartz and iron-carbonate veining, iron sulfides (mainly arsenopyrite and pyrrhotite), and accompanying silicate alteration minerals that overprint favorable chemical and structural traps late in the history of deformation.

Jan 1, 2004

By E. L. C. Martins, M. J. Nicol, D. Majuste, A. D. Souza

The effects of organic compounds on the current efficiency (CE), morphology, crystal structure and mechanical properties of the metal deposited during the electrowinning of zinc are described. A flotation collector and lubricating oil were selected based on observations made during the industrial production of zinc from silicate ores, in Brazil. The analysis by Fourier transform infrared spectroscopy of these compounds, which may be present in minor amounts in the electrolyte solution, indicated the presence of a polar amine group in the collector, while the lubricating oil is a non-polar compound. The average CE value obtained from organic-free industrial solution was 91.15 ± 0.26 %. The CE dropped to 54.35 ± 0.73 % in the presence of 100 mg·L-1 of collector in the solution, and a negative effect was also observed in the presence of similar amounts of oil (88.84 ± 0.61 %). The characterization of the deposits by scanning electron microscopy and X-ray diffraction revealed the formation of pores in deposits obtained from solutions containing the oil, while a different growth pattern (perpendicular zinc platelets) was identified when the flotation collector was added to the industrial solution. In the presence of these contaminants in the solution, guided-bend tests revealed that the deposits have a higher resistance to deformation, but lower ductility, properties that may affect the performance of the stripping stage. As a result of this work, simple control and optimization actions were applied in the industrial plant, which resulted in important improvements in the electrowinning process.

Jan 1, 2014

By Graham Swan

The case is presented for the development of a spray-on liner for ground support, but only in the context of a new mining system, consistent with the technical and business case advantages of liners compared to alternatives. Over the past 10 years much effort has been expended in specifying and testing the mechanical/environmental properties of various liners, without actually fulfilling any mining system requirements. The results have been generally disappointing, with no consistent and sustained application in a dayto- day production environment being achieved, anywhere. Central to this shortcoming has been the failure of mining/liner ma nufacturing companies to realise that screen/mesh or shotcrete cannot simply be replaced with thin, deformable liners: success will depend upon closely defining and evolving a new, liner- functional mining system. The paper begins with a discussion of some fundamental technical capabilities and constraints associated with 3M Canada?s liner material that has been developed in partnership with Falconbridge Limited. Intended applications for this liner include the support of bursting ground associated with deep mining conditions. With safe application and consistent performance in mind, the paper argues for a new mining system that derives in the first place from best quality drilling and blasting practices. Taking this as a given, a system for waterscaling and liner application prior to mucking out is proposed, followed by bolting through the liner while arranging for the bolts to be explicitly connected to the liner. Some logistical and equipment related challenges of such a mining system are then reviewed and discussed in the context of the business case for liners. It is concluded that this approach, if successful, will provide the greatest benefits in the areas of safer mining, due to reduction in worker exposure, and in reduced mining cycle times.

May 1, 2003

By A. Alfantazi, L. Choudhary

Gold leaching in thiosulfate solution has attracted widespread research interest through the last two decades primarily due to its perceived environmental benefits in comparison to the conventional gold cyanidation technique. However, the data on the corrosion and/or corrosion-induced failures of plant infrastructure materials in the solutions relevant to thiosulfate gold leaching are very limited. Accordingly, this study aims to characterize the electrochemical corrosion behavior of stainless steel 316L in the thiosulfate gold leaching solutions. Electrochemical corrosion response was investigated using potentiodynamic polarization and electrochemical impedance spectroscopy. The morphology of corroded specimens was analyzed using scanning electron microscopy.

Jan 1, 2014

By R. Burnette

Gold has been mined from a variety of deposit types that range in age from Archaean to Recent. The large variability in the geological settings of the gold deposits implies transport and concentration of gold by magnetic, hydrothermal and sedimentary processes. The factors that control the concentration of gold at certain sites and the grade estimation thereof remain major topics of debate. Due to the complex nature of the Witwatersrand Basin a mineralogical study, including mineralogical, petrographic and geochemical investigation was launched on TauTona Mine in order to characterize the various reef facies. The aim of the investigation was to determine if a correlation could be found between macroscopic characteristics of the reef, hanging wall and footwall, and the microscopic nature of the ore (especially gold grade). Petrograpgic and mineralogical results indicate that a correlation exist between gold, detrital and hydrothermal sulphides, uraninite, carbon, detrital heavyminerals and phyllosilicates. No correlation exist between gold and Mg, Fe or S. It appears that clast supported reef is of higher wade than matrix supported, but more work is suggested. No correlation exists between reef thickness and grade. The reef samples had the lowest phyllosilicate content compared to the hanging wall and footwall samples with pyrophyllite the most dominant. All of the correlations diagrams showed significant scatter and suggests a multi- factorial mineralization model. Gold distribution is also controlled by sedimentary features and thus it is not possible to select a single model for the formation and distribution of gold. It is evident that both sedimentary and hydrothermal factors influenced the mineralization and gold distribution on TauTona mine. It is thus essential that all related theories be incorporated in the development of a grade prediction model.

Jan 1, 2011

By V. Bondarenko

The importance and necessity of gas hydrates deposits development followed by natural gas extraction is considered in the present paper. Analysis is given to world sources focused on methane hydrates formation conditions. Information covering the most perspective gas hydrate deposit of the Black Sea is presented in the article. Two most common methods of gas hydrates development ? thermo stimulation and inhibitor injection are analyzed presenting their comparative characteristics. Basic scientific trends and developments of underground mining department in the field of gas methane extraction from gas hydrates are scrutinized. Schemes and methods of natural gas hydrates development are shown together with formulas, parameters and factors influencing the extraction process. Also the analysis is given to the possibility of gas hydrates formation from methane-air mixtures of degassing wells from coal mines of Ukraine. Improved experimental unit for gas hydrates formation under laboratorial conditions is presented with its basic characteristics. General conclusions and basic tasks requiring further research are given in the end.

Aug 1, 2013

By Pavel Vasak

Microseismic monitoring is becoming standard practice in the Canadian mining industry, particularly as mines get deeper. Full-waveform microseismic systems allow the operator to distinguish the event source mechanism, e.g., blast, shear slip or stress-induced fracture. At mine sites that heave a microseismic system operator blasts are manually identified by comparing the event waveform traces to the morning blast logs. However, this procedure is not routinely done at sites where a system operator is not present and this can lead to misinterpretation of the data at a later stage, particularly where the interpretation is outsourced, often many years later. It is critical to improve the microseismic data quality and consistency for processing and interpretation with a reliable technique to filter out blasts and blast related seismicity. This paper presents the development and implementation of a simple blast identification and filtering routine. The routine was developed specifically for Vale?s Creighton Mine about a decade ago, but is made sufficiently general so that it can be used at any mine site with an ESG (Engineering Seismology Group Canada) based full-waveform microseismic systems. The routine is strictly a post-processing procedure developed for use with the Access database data structure used by ESG. The algorithm was tested at Creighton Mine and a success rate of 80 to 90% was achieved, when compared to manual blast picks.

Oct 1, 2010

By H. Ewaschuk

"INTRODUCTIONRio Algom's involvement with the Enviro-Clear thickener began in May 1975, when tests on a laboratory waif were carried out by our Research and Development group. Commencing in June, further tests were carried out using a 3 foot diameter pilot unit. By December, a 30 foot full-scale thickener had been installed. In the near future, 3 more Enviro-Clear thickeners will be commissioned. With in the space of a year, almost $2.5 million had been committed to liquid/ solid separation facilities using the Enviro-Clear thickener. This paper briefly traces the extent and development of this commitment.BRIEF HISTORY OF QUIRKEQuirke Mine started operating in September 1956 at a rated capacity of 3,000 TOD. Because of market conditions, Quirke was shut down in December 1960. The facilities were re-opened at an increased capacity of 4,000 TPD in July 1968, by which time the demand for uranium had returned. Also, a second shaft was sunk, and by 1970, all of the ore treated in the concentrator was coming from the new Quirke II mine. The Quirke I stopes were allowed to fill with natural seepage. As well, acidic barren solution from the concentrator was pumped underground.With increasing demand for uranium, the capacity of Quirke will be further expanded to 7,000 TPD by 1978. Studies of how this expansion could best he carried out led to the consideration of a fairly new piece of equipment, the Enviro-Clear thickener, for certain operations in the concentrator. These operations are as follows:"

Jan 1, 1977

By R. Gutray, J. E. Grainger

This paper deals with the use of a cement-deslimed mill tailings mixture for a scraping floor in cut-and-fill stopes at Madsen Red Lake Gold Mines Limited. It describes the mixing and placing procedures and the precautions used with respect to the floor while mining in the stopes. Details of the mix are presented, and advantages and disadvantages discussed. The paper concludes with a brief outline of the costs.

Jan 1, 1966