Search Documents

By W. B. Evans, D. P. Taylor

"ANFO has two major disadvantages as an explosive low density and no water resistance. ANFO can be blended with more dense, water-resistant explosives to form ""Heavy ANFO"". The use of emulsion or slurry explosives as a matrix is an attempt to correct deficiencies on the basic ANFO while maintaining cost effectiveness.This paper will deal with four main topics.1. Product description, general properties, strengths and weaknesses.2. Technology of ""Heavy ANFO"" , the emulsion matrix concept and the range of products.3. Relative performance and economics in various rock types.4: Current status in Canada and worldwide, and the expectations for future use.IntroductionANFO has been in use for roughly three decades and remains the explosive of choice where conditions are suitable. ANFO has not become the universal explosive - despite its undoubted superiority in cost effectiveness - because it has serious flaws as an explosive. The most serious of these flaws are the low density and absence of water resistance in ANFO. Low density implies a low concentration of explosive energy in a borehole. The amount of energy available can be increased by. adding an energetic material, generally aluminum, or by drilling more holes. Both solutions add considerably to the over-all costs. The absence of water resistance in ANFO is inherent and can only be overcome by changing the fundamental nature of the product. The history of research in the explosives industry since the advent of ANFO is mainly the story of the various attempts to overcome one or both of ANFO's shortcomings.Many technologies and products have been developed to compete against ANFO, among them slurries, emulsion s and the so-called Dense ANFOs (ANFO with an extra nitroalkane liquid sensitizer). None of them was cost-competitive with ANFO so their market penetration has been limited to wet holes or specialized applications. The exception to this result is Heavy ANFO. The aim here was to have the best of both worlds, the high density and water resistance of emulsions or slurries plus the low cost of ANFO. The concept is very simple. ANFO is about 50 % air, roughly 30% in the prills and 700,10 between the prills . The air in the prills provides the necessary sensitivity but the air between them is waste volume. If one fills this volume with a high density, waterproof product, the resultant mix will be denser and more water resistant than ANFO and with very little added cost. This basic concept was invented by B. Clay in the 1970s and is covered by Canadian Patent No. 1 115 959. The water resistance and/or density of the mix can be tailored by changing the emulsion level. Because Heavy ANFO is relatively inexpensive while providing good in-hole densities and water resistance, it can compete successfully against all other bulk products. It competes against ANFO and Al / ANFO by allowing pattern expansion and reducing over-all costs while it competes against emulsions and slurries on price."

Jan 1, 1987

By Norman B. Davis

THE ceramic group of industries is comprised of those engaged in the manufacture of cement, glass, artificial abrasives, whiteware, including earthenware, stoneware, porcelain tableware, porcelain sanitary ware, electrical porcelain, floor and wall tile, porcelain enamel on metals, refractories of all kinds, sewer-pipe and structural clay products, such as terra cotta, brick, and hollow tile. The various sub-divisions of the industry produce a wide range of articles on which we depend for our creature comforts from day to day, perhaps to a greater extent than we generally realize. The industry, in turn, depends on a great number of minerals, and chemical products derived from minerals, and it is the object of this brief paper to present a list of these with notes indicating the particular applications. In order to bring home the importance of the industry to your daily life, stop and consider the many things around you accepted as a matter of course. Cement provides the smooth surfaces of many of our highways, city streets, and sidewalks. It enters into nearly all types of construction, alone or in combination with other clay products. Glass we hardly appreciate because we can see through it so easily, but it is there to serve us in windows, doors, and other light-transmitting structures. Glass is the universal means of transporting liquids and beverages, our beverages are usually served in it, and, with the recent development in fine spun glass textiles, there is a possibility of glass clothing in the future. Chinaware, a general term for table dishes, may be earthenware (not vitrified), semi-porcelain, or bone china, but it is before us three or more times a day ?and we seldom think of the minerals that have made these products possible. Floor tile, wall tile, and other ceramic specialties for interior and exterior use and decoration please the eye and provide sanitary surroundings.

Jan 1, 1938

By Jean-Luc Collins

"This paper shows how simple reliability concepts such as mean time between failures and mean repair time can be used efficiently to help increase equipment availability and so reduce the economic losses associated with unreliability.More specifically, the paper shows how these simple concepts can be used in maintaining an appropriate balance between fleet failure and repair rates and how they can be used for setting up priority repair rules f or queuing equipment.IntroductionA profitable mining operation must handle large quantities of ore and waste at the lowest possible cost. To achieve this objective, the operation must optimize the productivity of its fleets of equipment by efficient management of the time element. Figure I shows some basic equipment activities in an open pit operation while Figure 2 shows a tree diagram describing some time elements of these activities.It should be noted that the only time a piece of equipment can generate a profit is when it can be found in the operating status. In order to maximize this time element, the sum of the other time elements must be minimized because the total time is always fixed.This paper shows the application of simple techniques capable of reducing the waiting time for repair (maintenance delay) by using simple reliability concepts."

Jan 1, 1988

By R. Mohan Srivastava

"The goal of estimation is considered in the light of decision analysis. A simple example reveals the essential elements of decision-making in the face of uncertainty. A second example shows that these elements are also key features of many mining decisions. These two examples cause us to revive an old probabilistic notion that the goal of estimation should be to quantify what is unknown. The conditional probability distribution provides the complete statement of one's uncertainty. Once the conditional probability distribution has been established, one should retain as an estimate the value which minimizes some objective loss function. A third example shows how the ""best"" estimate depends on the chosen loss function. Current practice is almost exclusively based on the least squares method, which assumes a loss function which penalizes underestimation and overestimation equally. This is unfortunate not only because symmetry is an unrealistic assumption but also because mining offers a rare opportunity to state the loss function directly in terms of profitability. Both the theoretical framework and the practical tools exist to allow us to reconsider the conventional notion of the ""best"" estimate. IntroductionThis paper looks at estimation in the mining industry from the point-of-view of decision analysis. Virtually all decisions depend on estimates since few of the important parameters are ever known exactly. In this paper we will be referring mainly to the estimation of ore grades, though the approach discussed here is generally applicable to any decision in which relevant information is uncertain.In the first section we look at a very simple example of decision-making in the face of uncertainty. We will then tum to a mining example and see that the essential features of the simple example still pertain. From these two examples it will be clear that the decision analysis approach rests on two key concepts: the conditional probability distribution and the loss function. A third example demonstrates how different loss functions produce different ""best"" estimates from the same conditional probability distribution. In the final sections we willexamine the current practice of estimation in the mining industry. Though the tools for estimating the conditional probability distribution already exist, a change in the way we think about ""best"" estimates is needed. Very little attention is presently paid to the loss function even though it is readily available in many mining applications."

Jan 1, 1987

By Yulin Zhou, WenFeng Li, Wen Chen

"In this article, with the help of the X-ray photoelectron Spectroscopy (XPS), a modern test method, all the characteristics of the chlorite,and adsorption collector A6 on the surface of chlorite have been studied. There exist abundant carboxylic C-O and C=O structures in the Carbon XPS atlas with strong adhesive ability after the reaction between new collector A6 and chlorite, which indicates that the ring structure and ether-base functional groups can strengthen the reaction between collector A6 molecule and chlorite surface. The results of XPS analysis indicate that the photoelectron spectroscopy peaks of Mg2p and Al2p moved towards low energy after collector A6 absorbed on chlorite surface, which indicates that chemical bonding through electron cloud transfer happened between collector A6 and Mg, Al ions of chlorite surface. The chemical reaction promoted the adsorption of A6 on chlorite surface and eventually improved the ability of A6 to float and collect chlorite.INTRODUCTIONThere are a large amount of iron-bearing silicate minerals such as chlorite in different types of gangue minerals in iron ore from different areas besides quartz (Yingyong et al, 2012; Qiang et al, 2009). There always exist Mg2+, Al3+ Fe3+ and other metallic ions due the isomorphic replacement among the irons of this kind of minerals. The dissolution often occurs on the surface of minerals with abundant metallic ions during grinding process, and some ions are exposed on the surface, such as Mg2+, Fe3+, Al3+, Si4+, which can increase the surface electrical behaviour of iron-bearing silicate minerals (Wanzhong & Chuanyao, 2002; Yuping et al., 2007), making it easy for the surface to react preferentially with the depressants such as causticizing starch which making it impossible for the surface to reach with conventional anionic fatty acid collector (Mowla et al, 2008). Thus, the beneficiation efficiency is dramatically decreased and the improvement of concentrate grade becomes very difficult. The conventional aliphatic acid collector has some defects such as poor selectivity, poor low temperature resistance, sensitive to water hardness, etc. Thus, the addition of synergist (Liu, & Yu, 2015) or other compound reagents (Zhou et al, 2015) can promote the adsorption of reagents to mineral surface, and improve the collecting capacity and selectivity of aliphatic acid collector to minerals. The addition of polar group to nonpolar group in aliphatic acid can improve the water solubility, dispensability and hard water resistance (Tian et al, 2013). The nitrogen atoms in amid ate aliphatic acid collector can adsorb on mineral surface by itself and supply coordinate electron which can form chelating keys to improve the collecting capacity of collector. There exist coordinate electron in oxygen atoms of ether acid collector, which, along with the oxygen on carboxyl compose chelate with metal (Luo et al, 2015). There are also exist some opinions that the ether acid can arrange into similar crown ether structure which can absorb on mineral surface. A new alicyclic unsaturated ether acid compounds collector A6 is adopted in this paper, the structural formula is listed in Figure 1. The A6 has a strong collecting ability to chlorite with strong water solubility and low temperature resistance."

Jan 1, 2016

By C. Riveros, H. Henein

Bulk Metallic Glasses have a high potential as advanced engineering materials due to their various properties including strength and corrosion resistance, to name a few. This paper investigates amorphous phase formation and rapid solidification characteristics of impulse atomized Co-based alloys in order to understand and control the application properties of the final products. Amorphous fraction and kinetic crystallization properties of the atomized Co-based alloy powders were quantified by means of Differential Scanning Calorimetry. In addition, different but complementary characterization tools were used to analyze microstructures of the powders. These include optical microscopy, X-ray diffraction and micro-hardness tests. While the amorphous fraction within the powders is promoted by high cooling rate and smaller powder size as expected, hardness is found to decrease with the fraction of amorphous phase.

Jan 1, 2015

By T. C. Crosby

"Grinding has a marked effect on concentrator recovery and operating cost, and improved operation through automatic control can enhance plant performance. The correct application of automatic control can only be accomplished after the basic process variables and their effect on mill operation have been defined. This paper develops a control system for a closed circuit grinding system. Typical control systems, such as those for feed, water flow, level and circulating load, are discussed. A method of determining controllability, using the calculated reaction curve technique, is outlined. Various successful automatic grinding control applications are discussed and future possibilities are outlined. Although this paper primarily deals with closed wet grinding• circuits, the principles involved can be readily applied to other processes."

Jan 1, 1967

By Alan E. Cameron

WE assemble again today in this comfortable, hospitable Inn to begin this, the 58th, Meeting of our Society. It is just a year ago when last we met but that year was, probably, the most portentious year in the whole history of mankind. In that year, the German 'Atlantic Wall' was broached, the Rhine was crossed, and Germany, as a Nation, has ceased to be. The agony of Europe is over; convalescence may be, probably will be, slow. But blood no longer flows in Europe. Time will heal the sores, cover the scars, regenerate the industries, rebuild the cities, and re-establish the people. True, the war of all wars is not yet over. True, a bloody conflict remains . But, the power of the United Nations now converges on one target. The rain of blood will be heavy. We can hope the storm will be short. The sun is on the horizon. The light of peace 1s in the sky. What of that Peace? Are we ready for it? Have we a 'sure foundation ' for our future world? Are the footings under that foundation broad and substantial? Can we look forward with confidence to a lasting peace and a fruitful life? The United Nations, even as this is being written, are in conference in San Francisco, placing the footings, rearing the foundations for a world edifice. There are bickerings; there are jealousies. The world is tired, and a tired family always squabbles. We can, we must, believe that the decisions they make, the edifices they rear, will be better than anything we each could effect separately. It will be a compromise, probably; it will carry things that will hurt us, just as it will carry things that will hurt others. We can, we must, believe that the good of the whole is a greater good than the good of the part. Each Nation within the United Nations must sacrifice something, each part of each Nation must sacrifice something, each individual within each part of each nation must contribute something, if the whole is to be wholesome. Sacrifice and contribution must be the order of the day if the New World we are about to build is to be worth while. What of Nova Scotia? The world has travelled far in the last year; how far has Nova Scotia gone? Canada has preparations for the Peace under way; what has Nova Scotia done? Is Nova Scotia preparing counter measures for the sacrifices it must make? Is each of us ready to contribute his share?

Jan 1, 1945

By G. M. Hughes

"400 cubic foot Agitair Flotation Cells are in use at Sherritt Gordon's Fox and Ruttan Mine Cu-Zn concentrators. The 4 impeller model No. 120, used at the Fox Mine Operation, appears to offer superior agitation and aeration qualities compared to the single impeller model 120A, in use at Ruttan. The advantages of the model 120 are most significant with ores of high specific gravity and coarse grind.IntroductionSherritt is using 400 cubic foot Agitair flotation machines at both the Fox and Ruttan Mine Concentrators.At the 3000 tpd, Cu-Zn Fox concentrator, 18 model 120 machines have been in operation since May, 1969.The 10000 tpd, Cu-Zn operation at Ruttan utilizes 49 model 120A machines. The plant started operation in May, 1973.The 4-impeller model 120 flotation cell has been marketed by Galigher since the early 1960's but the single impeller model 120A is relatively new.Model 120 Agitair -Cell DataThe Model 120 (Dwg. 1) has floor dimensions of 101 x 10' and a lip height of 2~ to 4 feet to provide up to 400 cubic feet of volume. This machine is shown with a froth crowder and stabilizer plates which are optional.Each motor drives two agitators. 20 HP is recommended by Galigher but 25 HP is more realistic with massive sulphides. The SG of ?ox ore is about 3. 6.The Model 120 can handle up to 600 cubic feet of air per cell at 2 psig which requires 5-6 HP at the blowers. Air volume to each impeller is controlled by a valve from a main header.During the first 3 years of operation at Fox there were few mechanical problems with the 120's."

Jan 1, 1974

By Dao Dac Tao

The Vietnam coal industry in recent years has achieved the rapid growth. However, in the process of industrialization and modernization of the country, the demand for coal for energy is constantly increasing. This paper presents the Vietnam coal industry in the last stage: the opportunities and challenges facing the coal industry as it strives to become modern, highly effective and capable of meeting the demands of national energy security, all in harmony with socio-economic and environmental needs.

Aug 1, 2013

By Ifeanyichukwu Nweke

"Aluminium rolling processing from ingots to cold rolled coils comes with a lot of challenges especially in controlling defective products in casting, hot mill and cold mill operations. Hence this study focused on reducing defects at mills and cast-house using six sigma approaches. The use of six sigma approach will help the production experts to determine the gap between its operation and world class process. Practical data from First Aluminium Rolling mills were presented and analysed and mini improvement projects were proposed based on organisation need to achieve excellence. This study encourages aluminium alloy industries to pursue process improvement projects on the basis of analysis on data obtained from their shop floor, hence ensuring that through this, recovery is improved and cost of poor quality is reduced.INTRODUCTION Engineer Bill Smith while working at Motorola in 1986 introduced a new concept in which a set of techniques and tools are used for process improvement by controlling variations (defects). These tools and techniques are explained by an acronym DMAIC. D DEFINE the problem M MEASURE the variables in the problem A ANALYSE the variables of the problem I IMPLEMENT and verify the solution to the problem C CONTROL the solution to sustain it Most times in six-sigma approach, variations in the process that results in defects and customers’ dissatisfaction are targeted at 3.4 defects per million opportunities. There are numerous methods six sigma application use to achieve quality results and innovative strategies. Improving the quality of process through these methods helps identify and reduce variations which paves way for organisational excellence. In this study, it is encouraged to use six sigma techniques to improve aluminium rolling operations and other aluminium processing activities, the benefits of such improvement concept include: • Satisfy the voice of the customer (VOC) • Minimise costs • Maximise Profits • Build Good Team • Implement Profitable Project"

Jan 1, 2018

By H. F. Letient, D. C. Johnson

At the 25th Annual B.C. Mine Reclamation Symposium in September 2001, Huckleberry Mines Limited received the Jake MacDonald Reclamation Award for its exemplary mine waste management plan, conceived to prevent the onset of acid rock drainage (ARD) and facilitate reclamation of the site. The mine is an excellent example of a total mine waste management plan, with all materials scheduled in detail for the life of the mine. The filling plan for the waste management facility takes into consideration the requirement for permanently flooding the potentially acid-generating rock. From an acid generation point of view, the tailings fall in the zone of potentially acid-generating material. To avoid long-term ARD concerns, it is planned to float pyrite out of the tailings toward the end of the mine life, thereby generating a non-potentially acid-generating tailings stream which will be used to cap the deposited mine waste. The pyrite-rich tailings will be discharged into the deeper portion of the impoundment. On closure, a permanent water cover will be maintained over the mine waste. Only beaches of non-potentially acid-generating tailings will remain exposed. Mining will be phased to also allow one of the pits to provide storage for potentially acid-generating rock and to be flooded at the end of mine life.

Jan 1, 2004

By P. Talonen

Since the last Iron Control in Hydrometallurgy Symposium in Montreal in 1996, the Kokkola zinc plant has increased its capacity from 175,000 t/y to 280,000 t/y by installing an atmospheric concentrate leaching process, which has also affected iron control in the leaching circuit. Major changes have been made at the jarosite residue pond; a subterranean plastic wall reinforced with bentonite and cement has been built around the pond. A new water collecting system that is used for groundwater level control in the pond area was installed. With these two investments in the pond area, it is now possible to prevent any seepage flow from the pond into the surrounding environment. Water pumped from the residue pond is treated in the water treatment plant. This paper describes the behavior of iron in Kokkola's current leaching processes. The treatment of the jarosite, the improvements to the residue pond and the water treatment process are also described.

Jan 1, 2006

By G. D. Bysouth, G. Y. Wong

"The Endako molybdenum deposit is located 160 km west of Prince George, British Columbia. It occurs within the main body of the Francois Lake Intrusions, a composite batholith consisting of early, middle and late intrusive phases. The ore deposit is confined to Endako Quartz Monzonite, a middle phase intrusion, which is bound on the north by Carey Alaskite and on the south by Francois Granite, both late stage intrusions. In the mine aretz, the Endako Quartz Monzonite has been intruded by pre-ore dikes of quartzfeldspar porphyry and porphyritic granite, and by post-ore dikesof basalt.The Endako deposit forms a west-northwest trending body that has a strike length of 3360 m and an apparent width of 370 m. It consists of four structurally distinct zones: Endako East, Endako West, Denak East and Denak West. Principal sulphide minerals of the deposit are pyrite and molybdenite, accompanied by magnetite and minor chalcopyrite. Galena, associated with wulfenite and bismuthinite, occurs in some ores of Endako West and Denak as minute inclusions in molybdenite. The sulphides and associated minerals are hosted by quartz veins which occur principally in vein systems. Hydrothermal alteration accompanying ore mineralization has pervasively kaolinized the quartz monzonite host rock, and has locally produced K-feldspar and quartz-sericite-pyrite envelopes on quartz veins.Primary structural controls of the deposit are southwesterly dipping vein systems which strike 110° in the Endako zones, 110° to 130° in Denak East and 170° in Denak West. Secondary structural controls are northeasterly striking vein systems that dip northwesterly in Endako East and southeasterly in Denak. Domal uplift accompanying the rise of latest stage magma is considered to have caused intense dilatant deformation along older west-northwest trending shear zones, producing an elongated structural host for ore deposition."

Jan 1, 1995

By J. A. Finch, R. R. Cunningham

The amount of foam volume generated in relation to the gas flowrate has long been used to define the foaminess of a solution and to characterize surfactants. The vessel geometry and gas flowrate range can affect the foam volume results. A fixed area column was tested alongside a variable area conical vessel with two surfactants. It was found that the fixed area vessel will cause foam volume to expand or contract which masks the effect of the surfactant. The conical vessel showed two regimes of foam volume production dependant on gas flowrate. The low gas flowrate regime revealed the physiochemical nature of the surfactant while a high gas flowrate revealed kinematic properties. Foaming properties of a surfactant is best determined with a variable area vessel at low gas flowrate.

Jan 1, 2009

By Louise Corriveau

Exploration strategies have traditionally considered felsic gneiss complexes of the Canadian Shield sterile. This paradigm is challenged with the discovery of extensive granulite-facies Cu-Au, Fe oxides-bearing hydrothermal systems in the 1.4 Ga Bondy and 1.5 Ga La Romaine volcano-plutonic complexes of the Grenville Province. Early identification of magnetite-rich units in association with meta-exhalite and pelite-like units was key to targeting the search for mineralization, protolith information and indicators of pre-metamorphic hydrothermal activity during regional surveys of these frontier terrains. Textural evidences for a volcano-plutonic setting were found. There remained, however, numerous impediments to the recognition that the ubiquitous magnetite-laden units and associated aluminous gneiss were hydrothermal in origin. Many metamorphic reactions form magnetite at the amphibolite to granulite facies transition, and hydrothermally-leached rocks resemble metapelite or migmatitic restite, while carbonate alteration zones may look like marble or calc-silicate rock. Non-typical metamorphic mineral assemblages, modes and colours arise when hydrothermally-derived rock types are metamorphosed. These effective markers served as tools for reliable field identification of hydrothermally-altered rocks. In our case-studies, we traced pre-metamorphic hydrothermally-driven Fe-oxide precipitation in association with sericitization, albitization, pyrophyllite alteration, chloritization, and B enrichment by mapping unusually high contents of (1) magnetite or hematite, (2) biotite, (3) albite, (4) sillimanite, (5) orthopyroxene or phlogopite with cordierite, and (6) tourmaline or kornerupine. The unveiled garnetite, tourmalinite, and aluminous gneiss had assemblages that vary according to metamorphic grade and composition. To assess if high mode of Fe-Mg-Al phases resulted from partial melting (restitic residue) or metamorphism of hydrothermal rocks, we compared leucosome mineral assemblages, shape and amount with that expected of in situ partial melting reactions. In both areas there is no compelling evidence for these units to be restites. In contrast, the presence of lapilli in garnet-cordierite-sillimanite gneiss, though extremely rare, constitutes conclusive evidence for extreme pre-metamorphic high-sulphidation alteration of a volcanic protolith, while Fe-oxides or sillimanite-bearing nodules and veins record a less pervasive alteration. Geochemical research on element mobility and mass balance calculations further testified of an hydrothermal origin for these gneisses. The magnetite-rich units, together with calc-silicate rocks, garnetite, hornblendite, albitite among amphibolite, provided effective guides to sites of fluid discharge and led to the discovery of Cu and Cu-Au showings. With the presence of highsulphidation alteration, these features suggest early Cu-Au VHMS-type alteration halos within a predominantly felsic composite volcano-plutonic arc setting for both case-studies. Evidences for subsequent F-driven orthomagmatic fluid activity are also present.

May 1, 2003

By C. Edwards

ABSTRACT The versatility and specificity of rare earth elements (REEs) have led to their use in an everincreasing variety of applications in new technologies; consequently, demand for REEs has increased significantly. However, separating REEs safely and effectively is a complex and expensive process. This paper presents a review of REE mineral processing technologies, providing an update on current capabilities in REE mineral processing and REE extraction from the major commercially valuable REEbearing minerals such as bastnaesite, monazite, and xenotime, as well as the ion-absorption type of REE deposits.

Jan 1, 2013

By John I. Sharpe

Masses of pyritic copper and zinc ores are entrapped along the contact zone between two volcanic groups in the Matagami area. The upper limits of the sulphide concentrations tend to form concordant contacts against lava or cherty tuffite units of the younger group; the lower extremities tend to either follow transverse structures or merge with zones of dispersed sulphides. The sulphides are deformed and intruded by folded dykes. Close relations between metallization boundaries and volcanic lithology and stratigraphy, and a preliminary investigation of the fabrics and crystallization temperatures of the sulphide masses, suggest that the copper and zinc (but; not necessarily all the iron sulphides) were emplaced at h1gh temperatures during volcanism in near-surface lithological-stratigraphic traps. Introduction T HE Matagami area is centered 120 miles north of the Val d'Or and Noranda camps in north-western Quebec. For the present purpose, it is considered to comprise a 155-square-mile area in Isle-Dieu, Galinee and Daniel townships which encompasses the main sulphide masses. Airborne geophysical surveys within this area in 1956 led to the discovery of a large sulphide body -the.

Jan 1, 1965

By I. Le May

"The assessment of integrity in plants is discussed, together with the codes that are being developed for in service evaluation of engineering fitness for service. The use of Risk Based Inspection is described and some examples are provided of the evaluation of in service components in which flaws have been detected. An example of the assessment of the structure of a mine processing facility is described, and application of Risk Based Inspection and plant assessment procedures to mines is discussed. Periodic assessment of large plants and components to determine their integrity for continued safe operation is becoming a more accepted approach than formerly when regular shutdowns were the normal practice. This is on the way to becoming the preferred procedure for petrochemical plants and power generating plants, and the same philosophy is appropriate for many mining operations. Both the American Petroleum Institute (API) and the American Society of Mechanical Engineers (ASME) have committees developing codes for the continued operation of equipment as distinct from the existing design codes. The philosophy is one of risk-based inspection, which can be on a purely qualitative basis or more quantitatively based.The purpose is to reduce the inspection of unnecessary and non-critical items and to concentrate on the most critical components, reducing costs and downtime and increasing safety. The approach differs from that considered by many maintenance engineers, in that defects that are identified during an integrity evaluation do not automatically cause a component or structure to be condemned or require that repairs are made right away. The seriousness of the defect must be considered and the safe operating life can be estimated before it becomes necessary to replace or repair the unit or component. This is no different from what is done today with passenger aircraft and, to an increasing extent, with pressure vessels, reactor vessels and similar components in the petrochemical and power generating industries."

Jan 1, 1998

By Sergio Cattalani, David J. Kerr, Harold L. Gibson

Abstract - The Horne mine was truly a world class Cu and Au deposit. Between 1927 and 1989, it produced some 260 t of Au and 1.13 Mt of Cu from 53.7 Mt of ore that averaged 2.22% Cu, 6.1 g/t Au and 13 g/t Ag. The total value of Au and Cu production from the Horne deposit at metal prices of US$300/oz Au and US$1.00/lb Cu is an outstanding US$5.2 billion. The Horne mine was also a company builder. After optioning the property from Ed Horne (Tremoy Syndicate) in 1922, the Thomson-Chadbourne Syndicate discovered the deposit in 1923 and quickly grew to become Noranda, one of the world’s premier mining companies. This discovery fuelled exploration and, along with subsequent discoveries in the Val d’Or-Cadillac camps, led to the "economic development" of northwestern Quebec. The Horne deposit influenced and continues to influence genetic models for volcanogenic massive sulfide (VMS) deposits. Early observations at Horne contributed to an epigenetic replacement theory for VMS deposits. The most recent genetic model for the Horne, invoking sub-seafloor sulfide replacement of silicified and sericitized volcaniclastic host rocks within a graben, has subsequently been proposed for another giant VMS deposit, the Kidd Creek mine. The Horne and Kidd Creek deposits show many similarities, such as localization within synvolcanic grabens, long-lived hydrothermal activity uninterrupted by volcanism, sub-seafloor replacement sulfides, stacked sulfide lenses, zone refining, silicified footwall rocks characterized by high positive ?18O values, and association with FIII rhyolites. Notable differences between the two deposits include the lack of andesitic, basaltic or komatiitic flows at Horne, different inferred water depths, high Au content at Horne versus negligible Au, but sub-economic to economic concentrations of Sn, In and Cd at Kidd Creek.

Jan 1, 2000