Search Documents

By O. Peters, D. Lascelles, R. Caldwell

Ageing tests on a crushed Cu-porphyry ore were conducted to assess the impact of sample oxidation on flotation performance. The objective of the testwork was to simulate ageing of ore that would be blasted through block caving but not milled for possibly several months. Ageing was performed in specially designed columns, using site and deionised water to keep the samples moist over the entire ageing period. Samples from each ageing interval (0, 0.5, 1, 2, 4, and 8 months) were examined for physical and metallurgical changes resulting from the ageing process through chemical analyses, size analyses, and batch flotation tests.

Jan 1, 2009

By H. Yoshida, H. Hatta, T. Suzuki

"The effect of the copper and magnesium contents and quenching rate during quenching on the age hardening behavior of 2000 series aluminum alloys was investigated. For the higher copper-containing specimens as conventional alloys, like AA2024, precipitation of the stable phases increased as the quenching rate decreased under the as-quenched conditions. The maximum hardness after the artificial aging of air cooled(AC) specimens was much lower than that of the water quenched(WQ)specimens. On the other hand, for the lower copper-containing specimens, coarse precipitation did not increase even in the case of the AC. The age hardening behaviors of the WQ and AC were very similar such that the maximum hardness and aging rate were almost the same. Many parts of the fine precipitates that increased the hardness were thought to be the GPB zone or fine S’ phase for the WQ and relatively coarse S’ phase for the AC. From the calculated CCT(continuous cooling transformation)diagrams, the lower copper-containing specimens could maintain the copper and magnesium in the solid solution state during the AC, so they could be quenched at a rather slower quenching rate like the AC.INTRODUCTIONThe 2000 series aluminum alloys, containing copper and magnesium as the major chemical components, are some of the well-known heat treatable aluminum alloys. These alloys have a high quenching sensitivity, thus the age hardening ability of these alloys decreases with as low quenching rate. To prevent the decrease of the age hardening ability, quenching is done by a method such as water quenching, which is not very efficient in an industrial situation, because the method requires such large equipment. For these alloys, reducing the quenching sensitivity helps them to be produced in a rather convenient way. For example, 6000 series alloys such as A6063 have low quenching sensitivity, thus they could be quenched by only air cooling just after extrusion and they do not need water quenching. Based on these reasons, investigations of these alloys with high copper and magnesium contents have been conducted in the past to find a way to lower the quenching sensitivity by adding transition elements such as manganese, chromium and zirconium (Kanno, Suzuki, & Itoh, 1986; Suzuki & Itoh, 1986; Kanno, Sakuma, Muromachi, & Watanabe, 1988). However, very few studies have focused on the quenching sensitivity of the lower copper and magnesium containing alloys because of their usage for structural components with high strength, and most of the past studies have used only the fast quenching method like water quenching. On the other hand, from our recent results, there is a possibility to lower the quenching sensitivity of 2000 series alloys with lower alloying elements. In this paper, the effect of the copper and magnesium contents with lower alloying elements and quenching rate, especially in case of slower quenching rate than conventional quenching method, on the age hardening behavior of the 2000 series alloys is investigated by the hardness measurement, structure observation and thermal analysis."

Jan 1, 2018

By Dirige. A. P. E.

A study was conducted for an operating mine to determine the appropriateness of its tailings material to be used for the preparation of a low modulus, high density backfill. The research was initiated due to issues arising from increased observations of compressive failure of backfill placed in stopes and inconsistent backfill behaviour (i.e. increased backfill brittleness and modulus). Backfill materials investigated were classified tailings and de-slimed tailings. Characterization of the physical properties of the classified and de-slimed tailings materials was conducted to assess the effect that these material properties would have on the strength and deformation behaviour of high density backfill products made using them. Such behaviour was investigated to determine whether differences in tailings physical properties would influence the strength and modulus character of the backfill materials. Uniaxial (UCS) and consolidated-undrained triaxial compression strength tests were conducted to determine strength performance and deformation behaviour of backfill. This paper presents the results of the backfill material characterization study and how different particle size distributions affected the strength performance and deformation behaviour of the different backfill mixes. It also demonstrates how stress-strain curves generated from material strength tests were used to evaluate variation in high density backfill mix response when such materials were subjected to unconfined and confined (triaxial) compression loading.

Aug 1, 2013

By M. A. Cristovici

"In the last few years CANMET has taken the initiative by investigating the possibility of reactivating abandoned old tailings dumps (for gold production) which would be of potential economic interest across Canada.Nova Scotia was one location where numerous gold processing plants were in operation in the early days. A survey of the old tailing dumps was conducted and some areas of interest were selected. Among them were the sites identified as Lake Charlotte and Forest Hill.Ore samples collected from those tailing ponds were examined for their chemico-mineralogical composition and investigated for gold extraction. Three technological concepts were tested: flotation, direct cyanidation and flotation followed by cyanidation of the flotation concentrate. The combined flotation- cyanidation variant, yielding a gold recovery in the range of 90%, was recommended for processing the tailing ore.Pilot-plant runs carried out by a commercial testing firm (data not included in this paper) confirmed the conditions and results of CANMET's technology.As a result a consulting-engineering firm designed the processing plant which is expected to begin operation in the near future.IntroductionIn the last few years CANMET initiated a research program to locate in Canada, abandoned gold-silver tailing dumps of potential economic interest and to explore the possibility of recovering the precious metals from these old deposits by modern techniques.A literature search revealed that the first production of gold in Canada was recorded in British Columbia in 1858 and that, production prior to 1900 was essentially restricted to the Yukon, British Columbia Nova Scotia and Quebec. During the early 1900s, Ontario, Manitoba and the North West Territories joined the ranks of the gold producers.Early milling and recovery methods were mainly restricted to sluice boxes, gravity stamps and amalgamation. Froth flotation and cyanidation were introduced at about the turn of the century.Recovery of gold at plants using flotation and cyanidation was very good, therefore the tailing ponds resulting from those operations would, very likely be of little or no economic importance. However, the gold recovery at the amalgamation and gravity concentration plants appeared to be lower, indicating the possibility that significant amounts of recoverable gold would have been carried with the tailings to the dump sites."

Jan 1, 1986

By S. Y. Ezz, K. El•Guindi

A vertical tube, 8 m long and 2.5 cm in diameter, electrically heated to 650°C throughout the majority of its height, was used to study the-effect of ore feed rate and hydrogen flow rate on the reduction of fine iron ore particles. A correlation could be obtained between the combined effect of the amount of reducing gas and reduction time and the per-cent reduction. The results suggest that a method based on the reduction of fine iron ores while falling through up-streaming hydrogen cannot be recommended for industrial application.

Jan 1, 1969

By K. Lim, J. Sobil, L. Galarza Castillo, F. Tozlu

"For mining operations globally, the scale and criticality of the grinding mill drive has meant that selection of the correct mill drive technology is paramount. With so much depending on the successful implementation of the electrical drive system— safety operation, timely installation, availability, energy efficiency, minimum maintenance and extend its use as tool to assist during mill liner exchange—customers are justified in their scrutiny and slow adoption of new drive technology. From the first installation of low, fixed speed synchronous motors to the introduction of the current source and further voltage source variable frequency drive, innovations require long periods of time and mining customers willing to push the industry forward. In recent years, the variable frequency drive has been the stepping stone for a new generation of mill drive technology. In use for decades in other heavy industrial applications, the drives allow for system optimization in a myriad of ways. The most dramatic of changes is in the design of the motor. Where in the past motor design was bound by line frequency, today the designer can optimize machine size and, more importantly, eliminate the need entirely for the synchronous motor. Induction motor design has now progressed to the point where low speed operation is possible at efficiency levels nearing those of the synchronous design. Moreover, the simplicity of the squirrel cage design means that availability, reliability and spare part requirements are greatly improved. As the next step in the evolution of large pinion driven grinding mills, the low speed induction drive offers a new reliable and robust system to the market.IntroductionAs deposit grades continue to decline, new ways of processing ever greater concentrator throughputs have been required to maintain throughput efficient and profitable operations. Furthermore, the high risk nature of mining developments requires a constant search for safer, higher availability and more efficient equipment design. Limitation of downtime is a key factor in ensuring mining operations can be sustained through volatile market conditions. Often processing the entire mine throughput through just 1 or 2 lines, the crushing and grinding circuits are of particular criticality to the uptime and, thus, profitability of any mining operation."

Jan 1, 2016

By Kazutoshi Haga, Batnasan Altansukh, Yasushi Takasaki, Mohd Yazid Bin Abdul Razak, Atsushi Shibayama

"In this study, the volatilization behaviour of arsenic (As) and antimony (Sb) from arsenicantimony bearing minerals such as tennantite (Cu12As4S13)/tetrahedrite (Cu12Sb4S13) in copper ore was investigated using a roasting process. Specifically, the thermal decomposition of tennantite and the arsenic volatilization were investigated under nitrogen and air atmosphere. The roasting experiments were performed at temperatures ranging from 500 to 1,200oC and different retention times using a laboratory electric furnace. The results indicated that over 95% volatilization was achieved at 700oC. On the other hand, when the temperature increased to 1,200oC, volatilization rate of Sb reached to 90%. Therefore, volatilization of Sb requires high temperature compared to As. It suggests that As and Sb can be separated using temperature difference. Selective removal of As is possible at 700oC, subsequently Sb can be recovered as a volatilized product by increasing the temperature to 1,200oC. Meanwhile, volatilization of Cu and Fe was not observed on these conditions. The content of As and Sb in the residues obtained from roasting at 700 and 1,200oC was less than 0.3 and 0.75 mass%, respectively. The Cu content in solid residue at 1,200oC increased to 34 mass%. The clean copper concentrate with lower amounts of arsenic and antimony was obtained from the process. INTRODUCTIONRecently, arsenic (As) and antimony (Sb) contents in copper (Cu) concentrates are increasing year by year. Arsenic and antimony are present with Cu minerals such as enargite (Cu3AsS4), tennantite (Cu12As4S13) and tetrahedrite (Cu12Sb4S13) that associate with copper sulfides [chalcopyrite (CuFeS2) and bornite (Cu5FeS4)]. They are normally concentrated by flotation and treated in copper smelters. However, treatment of copper concentrates containing high amounts of arsenic and antimony by a smelting process is difficult due to environmental implications of toxic arsenic and antimony. As demand for copper continues to grow, the need to source copper from several types of resources including those that contain high levels of As/Sb becomes necessary. Therefore, a novel processes for the treatment of As/Sb bearing Cu concentrates are required. Reviews on copper resources such as enargite, tennantite and tetrahedrite containing high amounts of arsenic and antimony are covered widely in literatures by many researchers (Padilla et al., 1998; Welham, 2001; Vinals et al., 2003; Guo & Yen, 2005; Balaž & Achimovicova, 2006a; Filippou et al., 2007; Mihajlovic et al., 2007; Lattanzi et al., 2008)."

Jan 1, 2016

By K. Forsberg, A. Rasmuson, R. Rodriguez Varela, J. Martinez De La Cruz

"This study analyzes the separation of rare earth elements by means of a supported liquid membrane (SLM) with the final objective of recovering REE from an apatite concentrate (Alemrajabi, Forsberg, & Rasmuson, 2015; Mohammadi, Forsberg, Martinez de la Cruz, & Rasmuson, 2015). In this study, the feed phase consists of an aqueous phase containing REE, the membrane phase contains the organic solvent and carrier (D2EHPA and EHEHPA), and the stripping phase is a hydrochloric acid solution. An evaluation of mass fluxes, separation efficiency, and membrane performance is conducted. In order to analyze the suitability of liquid membranes in the extraction of REE, a deeper insight into the mechanisms causing instability is needed. In this study, surface tension is considered as the key factor of Marangoni instabilities and spontaneous emulsification.INTRODUCTIONThe demand of REE and their compounds has increased considerably due to their special physicochemical features that make them crucial elements for numerous high-tech applications, including wind turbines, hybrid cars, mobile phones, and defense technologies. They are also extensively utilized in traditional industries such as nuclear energy, petroleum, metallurgy, agriculture, and textiles (Xie, Zhang, Dreisinger, & Dyole, 2014; Zhang, Wu, Bian, & Zeng, 2014).Solvent extraction is widely used for the separation of REE (Xie et al., 2014; Zhao, Huo, Pan, Li, & Liu, 2014). Di-(2-ethylhexyl)-phosphoric acid (D2EHPA) and 2-ethylhexylphosphonic acid mono-2-ethylhexyl ester (EHEHPA) are two of the most effective extractants for the separation of rare earth elements among organophosphorus extractants (Gupta & Krishnamurthy, 2005). However, the difficulty in stripping loaded D2EHPA extractant, especially for heavy REE, has limited its utilization. Yttrium can be stripped at lower acidities in EHEHPA systems compared to D2EHPA systems (Gupta et al., 2005), but the extraction efficiency is lower. Conventional solvent extraction by mixer-settlers is restricted by its large solvent inventory and loading limits, and suffers from phase disengagement, emulsification, loss of solvent, and flooding problems (Swain, Jeong, Lee, & Lee, 2007). In this context, supported liquid membranes (SLMs) present a potential alternative due to their advantages, being low solvent inventory, process simplicity, low energy and operational costs, great enrichment ratio, and combination of extraction and stripping into one single step. A SLM is a system in which two aqueous phases are separated by an organic liquid membrane suspended in the pores of a porous support by capillary forces. One of the aqueous phases is the feed solution with the solute and the other is the stripping or receiving solution. The solute diffuses through the liquid membrane and then is extracted into the stripping solution (Kislik, 2010)."

Jan 1, 2016

By D. P. McDonald

"IntroductionTHE PURPOSE of this paper is to present .a summary of the evidence given before the Petroleum and Natural Gas Conservation Board in support of applications to it for permits to export natural gas from Alberta.I will attempt to be objective in my statements, despite the fact that my main interest in the hearings before the Board was to advance the interests of my own clients, the Westcoast Transmission Company, Limited.The hearing of the export applications •commenced before the Board in January, 1950, with the .application of the Westcoast Transmission Company. Joint hearings were commenced in September, 1950, and completed on December 14th, 1951. The Board heard evidence in support of six applications for export, one application to build a gathering system in Alberta, and three interveners, the .latter being the City of Calgary, the local gas companies, .and the coal interests, including both operators of coal mines and the Unions.The evidence comprised better than 8,400 pages, over two million words, and occupied 92 days before the Board.The Interest in Natural GasThe natural gas industry is one of the newer industries. It is not yet twenty years •old. In the United States, the expansion •of pipeline facilities has been phenomenal in the last fifteen years, and particularly in the last three years, when a total of over two billion dollars was invested in pipeline facilities. There are approximately 250,000 miles of gas transmission pipelines in the United States at this time, with additional lines constantly being pressed."

Jan 1, 1952

By Pierre Lacombe

"The operation of the Louvicourt Mine will have to rely on stringent grade control and on the optimization of the amount of blocked ore made available per given development effort. All of the above being necessary to obtain the highest throughput at the lowest mining cost.To assist in achieving these objectives, the need for production of a competent fill with short curing time was recognized early by the project partners. As well, operating costs associated with the selected method should be as low as possible while meeting the technical criteria.A feasibility study comparing filling methods showed potential benefits in all aspects of the paste fill use, except for its higher capital costs and increased operational complexity. This last consideration was tackled by the conservative design approach adopted in the flowsheet development of the paste fill plant.Since commissioning of the plant has just been completed at this time, the paper will focus on the feasibility study and its background, the design of the plant and testwork results at pilot plant and plant scale.RésuméLe succès de l 'opération de Louvicourt Mine dépendra d' un contrôle serré des teneurs du minerai et de la maximisation de la quantité de minerai développée par effort uni ta ire. Ces critères devant etre respectés afin d'obtenir le taux de production le plus élevé au coût le plus bas.De façon à satisfaire ces contraintes, les partenaires du projet ont reconnu tôt la nécessité de produire un remblai de qualité tout en maintenant un temps de curage court. De plus, les coût d'opération associés a cette opération se devaient d'être des plus avantageux sans sacrifier l'atteinte des objectifs techniques.Une étude de faisabilité comparant différentes méthodes de remblayage a démontré que le remblai en pâte offre des aspects positifs sous taus les angles, si ce n'est de son coût en capital initial élevé et de sa complexité relative d'opération. Ce dernier point fut considéré de près par l'adoption d' une approche conservatrice lors de la conception de l'usine de rernblai.Puisque la mise en service de l'usine n'a été faite que les détails de l 'étude de faisabilité et ses fondements, 1 'usine et des résultats d' essais obtenus a l'échelle de l'usine seront discutés."

Jan 1, 1995

By Neil McMillan

"By any measure of common practice, Claude Resources' Seabee Gold Mine in Northern Saskatchewan should not now be operating. Not because reserves dwindled, or grade dropped or prices weakened or technical problems arose, but because a host of unimaginable other problems beset the project, any one of which would normally have led to the mine's failure.The success of the Seabee Mine, and it is extremely successful, is a story of the vision and blunt determination of two men. Neither is remarkable in his own right but each possesses the characteristics which were necessary to forge a highly productive and profitable narrow-vein mine in the midst of the most bizarre and unpredictable events which likely have ever beset a mine start-up in Canadian history.Together, Bill MacNeill, a Saskatchewan born, former bush pilot and Ray Gagnon, a big hearted, hard-fisted, miner with 44 years of experience in Canada's underground, built the Seabee Mine.They didn't accomplish this with brilliant geology, outstanding engineering or nimble corporate manouvering but rather a stubbornness and raw common sense which likely are all too often, ingredients missing in failed projects.The Seabee Mine is 100% owned by Claude Resources, a Saskatoon based company taken over by Bill MacNeill, its current chairman, in 1982. The company is listed on the TSE and produces 1200 barrels of oil per day and about 60,000 oz of gold per year. The company has a strong balance sheet, is very profitable and has 18 million shares outstanding.The Seabee property in Northern Saskatchewan started out like many other gold exploration properties in Canada.It was discovered in the l 940's by what is now Cominco, and, while highly regarded by that company the property sat largely dormant until acquired by Claude Resources in 1985.Claude did what most junior exploration companies would do and went looking for a company with a depth of expertise to joint venture the property.That company was Placer Development who could earn a 55% interest in the Seabee by delivering a bankable feasibility study on the Project by July 1988 and providing financing to production.Placer Development was an excellent company and spent over $8 million dollars on the Seabee over a 3 year period. Unfortunately for Claude Resources, Placer Development merged with Dorne Mines in 1987 and the new merged company, Placer Dome, established a minimum production threshold greater than the 50,000 oz per year which the Seabee appeared capable of supporting at that time. Placer Dome's request for an indefinite extension of the joint venture agreement to allow it to drill off a larger ore body was rejected by Claude Resources and the Seabee Property was returned to Claude in 1988."

Jan 1, 1998

By B. W. Raymond, D. W. Zandee

"IntroductionCoal deposits are found in many regions in Canada and vary widely in their age, quality and rank. All classifications of coal except anthracite are found in significant quantities in this country.Deposits in the Maritimes are mainly bituminous; Lignite is found in Saskatchewan and Ontario and sub-bituminous coal in the plains region of Alberta. The Rocky Mountain coalfields of Alberta and British Columbia contain low and high-volatile bituminous coal and, in a few places, semi-anthracite. The British Columbia interior contains deposits of semi-anthracite, bituminous, sub-bituminous coals and lignite. The Yukon and Northwest Territories also contain substantial deposits of bituminous coal and lignite.Currently Nova Scotia produces both thermal and metallurgical coal, Saskatchewan produces lignite and Alberta produces both sub-bituminous and bituminous coal for thermal purposes. Large deposits of metallurgical coal are now being exploited in the Rockies arefl of British Columbia and Alberta by open pit methods. The raw coal is treated in large capacity preparation plants to remove refuse and upgrade the product to a consistent metallurgical quality with respect to ash, moisture, volatile matter and coking properties.The treatment of coal involves crushing, screening and cleaning by dense medium, jigs, water-only cyclones, tables and froth flotation to produce a diverse range of coal products differing in quality and size for various end uses.The chapter on Crushing and Screening Circuits was concerned mainly with crushing of metalliferous ores to produce a concentrate of one or more valuable minerals which normally constitute a small portion of the original mass of the material treated.Coal differs physically from ores in many ways such as lower specific gravity, relatively large volumes but low tonnage of product, and its habit of absorbing moisture requires extensive dewatering processes more complicated than settlement and filtration. Most significant, for this paper at least, is the fact that crushing coal is not as energy intensive and much smaller equipment is applicable.Crushing and screening of ores is intended to reduce the size of all constituents as quickly and efficiently as possible to allow liberation of the mineral particles. The crushing of coal is different in that the coal is not the minor constituent and the production of fines, in the initial stages at least, is highly undesirable. The basic objectives of crushing coal are the reduction of run-of-mine material to sizes suitable for cleaning or further reduction of coal to market sizes."

Jan 1, 1989

By John Frostiak

"Kahama Mining Corporation Limited, a wholly owned subsidiary of Barrick Gold Corporation, poured the first dore bar and filtered the first concentrate produced at the Bulyanhulu mine on February 28, 2001. This event marked the completion of the initial development of the Bulyanhulu Mine – Barrick’s first mine located outside of the Americas.Bulyanhulu is a 2,500 tpd underground mine located in the Lake Victoria gold belt of northern Tanzania. Gold is recovered as a gravity concentrate and smelted on site to produce dore bars or collected in copper concentrate that is shipped to offshore smelters. The facilities were constructed to meet Canadian standards. Unit operations include single stage crushing, SAG milling, gravity recovery, flotation, thickening and dewatering. Tailings are converted to paste and returned underground as paste backfill or pumped to the surface tailing site. The surface paste tailing disposal system is believed to be first of its kind in the gold industry. Paste disposal has several advantages over slurry, including lower dam construction costs, reduced water losses, and lower reclamation costs. This paper describes the facilities and discusses the challenges faced during development and construction including logistics, lack of infrastructure, recruiting and training, security, and social issues as well as initial operating results.INTRODUCTIONBarrick Gold Corporation completed the Bulyanhulu mine development in 2001. Capital cost of the project was US$280 million. The mine produced 241,575 ounces from start of milling to year end at a total cash cost of $197 per ounce. Numerous challenges were overcome in the mine’s development due to the general lack of infrastructure in Tanzania and the mine’s location some 1200 km inland by road from the port of Dar es Salaam."

Jan 1, 2003

By Claude K. Howse

The area covered by the present paper consists of about fifty square miles in the immediate vicinity of the settlement of St. Lawrence, which is on the Southern extremity of the Burin peninsula on the south coast of Newfoundland. Physiography Physiographically, the area is part of the Atlantic upland, equivalent to the New England province of the United States. Evidences of two erosion surfaces are to be seen truncating the intrusives and the folded volcanics and sedimentary rocks. The older erosion surface is represented by small monadnocks from 650 to 750 feet in height with the younger surface covering most of the area and characterized by rounded subdued topography with maximum relief of two to three hundred feet and numerous ponds and bogs. These surfaces have been correlated with the High Valley and the Lawrence peneplains of Newfoundland. On the Avalon peninsula, these peneplains have elevations of, respectively, from 1,300 to 1,700 feet and from 500 to 1,000 feet. Glaciation The entire peninsula has been glaciated, with lee-and-stoss slopes showing on the highest hills in the immediate vicinity, many of which have striae and erratics on their summits. The lee-and-stoss slopes, the glacial striae, and the distribution of certain rocks found in the drift and whose source outcrops are known, indicate a southward direction of ice movement.

Jan 1, 1951

By J. P. Sims

Abstract - Ultramafic to mafic igneous intrusions of the Las Aguilas district form part of a belt of generally mafic plutonic bodies within medium- and high-grade early Paleozoic metamorphic rocks in the southern Sierras Pampeanas region, Province of San Luis. The intrusions host the largest known nickel sulfide resource in Argentina and contain significant Cu, Co and PGE mineralization (2.2 Mt at 0.5% Ni, 0.5% Cu, 0.035% Co). Sulfides at Las Aguilas Este, one of two principal mineralized zones, are hosted by a body comprising subvertically dipping units of predominantly orthopyroxenite and melanorite cumulate, with lesser dunite, harzburgite, norite, leuconorite, and amphibolite. The units are zoned horizontally from ultramafic to mafic compositions, representing primary magmatic zonation away from an original base or side of the intrusion. Intercumulus nettextured and disseminated aggregates of pyrrhotite-chalcopyrite-pentlandite are concentrated in the peridotitic zones and extend into melanorite. Whole rock major and trace element compositions, and olivine chemistry, indicate that the parent magma was gabbroic/basaltic with 100 (Mg/Mg+Fe) near 59, and resembles tholeiitic magmas generated in subduction-related arc, or back-arc settings. Unusually aluminous Cr-bearing spinel is compositionally similar to those in some synorogenic mafic/ultramafic plutons in magmatic arc settings. Relatively Ni-depleted olivines and low Cu/Pd ratios are indicative of magmatic sulfide segregation early in the crystallization of the magma. Early orthopyroxene saturation and virtual lack of clinopyroxene, in conjunction with sulfur isotope values up to +6.6 ‰, spinel compositions, and presence of graphite, phlogopite and magmatic hornblende, all attest to probable crustal contamination of the parent magma. Assimilation of crustal sulfur may have been crucial in the early attainment of sulfide saturation and resultant formation of magmatic Ni-Cu sulfide mineralization. Fabrics, textures and mineralogy of the intrusions and country rocks and U-Pb zircon dating indicate syntectonic-synmetamorphic emplacement at 478±6 Ma during the Famatinian (Ordovician) orogeny. Minor to locally significant recrystallization and deformation of mafic-ultramafic rocks and redistribution of sulfides and PGE occurred during and following the Famatinian orogeny. The Las Aguilas intrusion is one of several tholeiitic mafic-ultramafic intrusive complexes within an Ordovician arc - back-arc system in the Sierras Pampeanas. Aeromagnetic datasets and regional mapping suggest there is further potential for intrusion-hosted Ni-Cu mineralization along this eroded magmatic arc.

Jan 1, 1999

The AG/SAG circuit discharge P80 is now increasingly referred to as the ?Transfer Size? or T80 for short. From the literature it is apparent that in circuit design some approaches to the sizing of AG/SAG mills as well as the ball mills that they feed use this parameter. This paper reviews whether the use of the T80 is appropriate in this context. In the course of the review examples of AG/SAG discharge size distributions measured from range of operating circuits are used to illustrate the arguments made.

Jan 1, 2012

By J. P. Bennett, K. S. Kwong

Slagging gasifiers are used to produce chemicals and/or electricity from feedstocks such as coal and/or petroleum coke. A gasifier environment includes pressures from 400 to 1000 psi, temperatures from 1250-1550°C, are cyclic, reducing gases of CO and 112, and molten ash that interacts with the refractory liner materials. The high Cr2O3 refractory liners of gasifiers fail within 3 to 24 months. Gasifier users seek materials with increased reliability and service life. This paper discusses causes of refractory failure and efforts to increase refractory service life.

Jan 1, 2004

By M. Ghamgosar, Erarslan N.

Rock cutting includes many unknown parameters which result in different consequences of the different cutting conditions. However, based on the current suggested models for rock cutting, there are some critical parameters that control the fracture initiation and propagation in the rock domain. In general, there are two major cutting tools are used in rock cutting: drag bits and indenters. Different mechanical attacks of cutters result in different fracture models. For example drag bits break the rock parallel to the rock surface, which is called ‘undercutting’ while indenters cut rocks by pressing normal to the rock surface. Both tools cause rock failure by inducing tensile cracks in the rock. However, drag bits induce more tensile cracks compared with the indenters. The full benefits of improvement in rock cutting efficiency will arise from a clear understanding of rock fracture mechanics principles. Therefore, fracture mechanics principles will be applied to the rock cutting as the rock fragmentation process is based on the rock fracturing. The Oscillating Disc Cutting (ODC) has more advantages than drag bits and disc cutters. The forces transmitted back through the cutting head are much lower with ODC. Although ODC attacks rock in much the same way as drag bits, a combination of the oscillating action of the cutter and the undercutting mode produces the lower cutting forces and causes rock fatigue. Fatigue phenomenon in rock has advantages for the rock breaking by applying less effort and energy due to the cyclic loading. The aim of this study is using the Extended Finite Elements Analyses (XEFM) numerical modelling for simulating the ODC cutting with different cyclic loading conditions. An accurate prediction of numerical investigation requires detail laboratory experiments. A series of laboratory tests were performed to obtain the fracture toughness values of our Monsonite rock samples under various cyclic amplitude and frequency values. The numerical results showed different types fatigue damage mechanisms due to the various cyclic loading conditions. Thus, modelling and understanding the crack propagation behaviour depending on different amplitude and frequencies are believed very important for the dynamic rock cutting researches and rock cutting machine manufacturers.

Jan 1, 2015

By A. E. Boudreau

Abstract-It has long been recognized that platinum-group-element (PGE) deposits in layered intrusions preferentially occur in intrusions that crystallized from high-Mg parent magmas. Recent studies suggest that evaluation of any given intrusion for economic PGE potential should also include assessment of the PGE, sulfur and chlorine concentrations in the cumulates and potential parent liquids. PGE: Magmas that contain relatively abundant Pt and Pd are the best candidates for forming economic deposits. Although analyses of coeval sills and dikes are the best indicators of primary magmatic PGE concentrations, analysis of the cumulates themselves is also valuable. For example, within the Stillwater complex, background PGE values in cumulates from the ultramafic sections of the complex contain, on average, several 10s of ppb Pt and Pd. Background concentrations of this order are suggestive that the magma was not depleted in the PGE. Sulfur: Conventional petrogenetic models for the formation of PGE deposits in layered intrusions require the PGE to have been concentrated during a magmatic sulfide-saturation event. In contrast, some hydrothermal models suggest that sulfur and the PGE were mobilized from footwall cumulates by upward- migrating, high-temperature hydrothermal fluids. Both models suggest that significant PGE deposits are likely to occur at and below the level where stratigraphic increases in whole rock sulfur concentrations occur. Chlorine: In both the Stillwater and Bushveld complexes the cumulate sequences below the major PGE-bearing zones contain anomalous Cl-rich apatite. The chlorapatite component of apatite in these rocks may exceed 40% and, in the Stillwater complex, typically exceeds 90%. It is stressed that pristine igneous mineral analysis and not whole rock data be used, as whole rock Cl concentrations may be affected by very localized (grain boundary), low-temperature alteration. Intrusions that crystallized from high-Mg, high-Cl magmas appear to have the best potential to host significant PGE deposits.

Jan 1, 1995

By Daniel Hodouin, Claude Bazin, René del Villar

"A traditional linkage has long been established at Laval University's Department of Mining & Metallurgy between the Mineral Process (MP) and the Mining Exploitation (Min) on one hand, and between the Extractive Metallurgy (EM) and the Materials Engineering (Mat) on the other. This academic separation of Mineral Processing from Extractive Metallurgy at the educational level has become increasingly at odds with today's industrial practice in which both disciplines are not only complementary but also often intertwined. For instance, in gold ore processing, comminution, flotation, and gravity separation units are interfaced with atmospheric or pressure leaching modules and with carbon adsorption and electrowinning units. The new copper plants in South America combine comminution and flotation circuits with heap leaching, solvent extraction and electrowinning processes.In order to reflect this new industrial reality and to harmonise the options offered in both its engineering programs, the Department of Mining and Metallurgy of Laval University has introduced major changes in its curriculum in 1996. These changes reflect also the recognition that the somewhat secondary status given so far to Mineral Processing and to Extractive Metallurgy within their ""mother"" programs, Mining/Mineral Engineering and Materials metallurgical Engineering respectively, was in sharp contrast with their actual significance for the Canadian economy. Leading industrial voices have raised similar concerns and the Canadian Engineering Accreditation Board has also addressed this problem in its latest program evaluation.The changes implemented at Laval aimed at a) better representing MP and EM within the two undergraduate programs; b) training top-level versatile and multidisciplinary engineers, fluent in all aspects of MP and EM, irrespectively of which of the two ((mother)) programs they had chosen and capable of meeting today's industrial requirements; c) training students in process analysis, optimisation and automatic control using state-of-the-art software, and d) taking into account the co-operative nature of both undergraduate programs.Results are very encouraging in terms of student enrolment and industrial response. However, some concern is expressed on the sustainability of the renewed curriculum considering the drastic budget restrictions in effect at Laval as in most other Canadian universities."

Jan 1, 1999