Search Documents

By John Lund

INTRODUCTION GOLD-BEARING placers of Alaska and the Yukon Territories are buried under a layer of permanently frozen alluvial overburden, or 'muck', which varies in depth from twenty to one hundred feet. The placers, and the decomposed bedrock layers upon which they are deposited, are also permanently frozen. During the summer, surface muck which is exposed to the sun will thaw, but only to a depth of a few feet. To reach a valuable deposit, the frozen overburden must be either penetrated with shafts, or stripped from the deposit entirely. In either case, before the placer can be mined, it must be thawed. At modern dredging operations, the frozen muck is stripped from the placer by powerful jets of water from hydraulic giants. The placer, and several feet of decomposed bed-rock, are then thawed by forcing water through narrow pipes which have been driven into the deposit. Other methods of thawing frozen placers were used extensively during the early years of the Klondike 'gold rush', but experimentation later proved that creek water at its natural summer temperature was a more effective and economical thawing medium than any other which had been used. EVOLUTION OF COLD WATER THAWING Early prospectors of the far north reached placers by digging shafts through the frozen muck. They then thawed the placer sand and gravel by building wood fires at the bottom of the shafts.

Jan 1, 1951

By Jasmin Raymond

Ground source heat pumps are used to heat or cool building and heat water supply. Such heat pumps use the earth as a heat source or sink to efficiently provide or store thermal energy. For example, a ground source heat pump typically requires less then a third of the electric or fossil fuel energy of a conventional heater. Ground source heat pumps could therefore help reduce the energy consumption of active mines where low-grade geothermal resources are abundant. In most heat pumps, water or a water-antifreeze mixture having a temperature ranging from -6.5 to 43.5 °C is circulated through a heat exchanger at a rate of 0.000033 to 0.000067 m3/s (2 to 4 L/min) for each kilowatt of heating/cooling capacity. The groundwater that is continuously pumped to drain mines could be used to operate heat pumps. Water feeding a heat pump can alternatively circulate in a close loop network of pipes buried underground or installed in a surface water body. Retention water ponds, tailings and waste dumps commonly found at active mine sites could provide excellent environments to install the close loop system. Further research will help take advantage of the unexploited geothermal resources associated with actives mines.

May 1, 2007

By Maurice Morton

THE use of organic and inorganic stains has found wide application as a means of detection and estimation of organic fibres. Such stains have enabled the analyst to distinguish between organic fibres of different type and even between wood fibres produced by different processes. Among these stains, aqueous iodine solutions have figured prominently, as in the case of the well-known Sutermeister and Herzberg stains. At the Johns-Manville laboratories, the idea of applying a stain to asbestos fibres was first considered solely as a visual aid in the microscopic examination of such fibres. The staining medium used in this work consisted of a 1 per cent solution of iodine in C.P. glycerine, the latter being used extensively here as a dispersing and mounting liquid for asbestos fibre. This iodine solution was found to have distinct staining properties when used on the local chrysotile fibres, and to improve greatly their visibility under the microscope. It was soon revealed, however, that this staining is apparently limited to the chrysotile variety of asbestos, as against other varieties. It can be readily seen that, if such were the case, the staining test would become a very useful tool in differentiating between chrysotile fibre and the other mineral fibres, without recourse to a lengthy chemical analysis. Hence this investigation was launched, with the purpose of obtaining more information as to the selectivity of this stain as well as its mechanism. The only previous work of this nature that could be found in the literature was that of Van Winsen and Graham (1, 2, 3) on the adsorption of erioviolet dye by serpentine and related magnesia minerals. However, these authors did not refer to any specific behaviour of chrysotile as against other types of asbestos fibre.

Jan 1, 1941

By K. Purazrang, P. Sh. Naseri, P. Abachi

In present work, the comparative measurement of aluminum alloys' resistance to the unstable fracture was provided. Besides, the rupture mechanisms of high strength 7075 and 7050 aluminum alloys were investigated. The specimens were used as solution treated, quenched and aged condition. The elastic-plastic behavior of specimens was determined by carrying out tensile test on cylindrical specimens. The small sized specimen with 6.35 mm thickness and V-notched radius less than 60 µm was used for evaluation of damage properties, in accordance with ASTM B871-96 standard test method. All tear specimens were machined in L-T orientation. The mechanical tests were conducted at RT on an universal Instron machine under cross head speed of 0.1 mm/min. The results of mechanical tests made the evaluation of tear strength to 0.2 % tensile yield strength ratio, as a measure of notch toughness, available. The comparison of specimens' resistance to crack propagation and unstable fracture due to the presence of crack-like strain concentrator was provided using tear test data. The microstructure of specimens was studied under optical microscopy. The rupture micro-mechanisms were analyzed by examination of specimens fracture surfaces using SEM. The microstructure examination indicated almost equiaxed grains on the transverse directions and elongated grains on rolling direction. Moreover, intermetallic particles were evident at microstructure. Considering the SEM fractographs, it seems that the intermetallic particles act as void nucleation and damage initiation sites. However, the damage mechanism of tensile specimens and severely notched specimens, especially near the notched root differs due to stress and strain states.

Jan 1, 2006

By G. V. Theja, V. B. Maji

Large infrastructure projects like tunnel excavations, underground constructions face innumerable risks. For successful completion of these projects, it is essential that we foresee and understand risks that could occur during different phases of the project. One of the risks affecting underground excavation projects is the inaccurate performance prediction of TBMs. As this could severely affect the project, resulting in lower advance rates and could also result in changing the excavation machine or method, due to difficulties in excavation, thereby increasing the overall cost of tunnelling. This makes performance prediction of the TBMs as one of the crucial aspects in tunnelling, as a precise estimation of its performance is required for planning and estimation of time and cost of the tunnelling projects. This performance prediction of TBM is a challenging geotechnical problem that is intricate and complex in nature, this is possibly due to the fact that TBM performance prediction involves understanding the rock fragmentation process in wide range from micro-scale (i.e. the interaction of surface of rock material and cutter tip) to macro-scale (including the interaction of rock mass and TBM). Thus in order for the performance prediction model to be efficient, parameters of both TBM specifications and ground conditions have to be considered. Various models have been proposed by researchers since the early phases of TBM application, these studies resulted in the development and improvement of numerous penetration prediction models. Most of these models consider the geotechnical parameters that are input to the model to be consistent along the TBM drive and neglect the uncertainties in parameters that occur. And so to improve the predictive capability of these models and to incorporate the above uncertainties, the penetration rate is modeled as a stochastic variable depending on the geotechnical and TBM parameters, its statistical distribution is determined and is used to characterize the penetration rate instead.

Jan 1, 2015

By W. K. Muwais, R. G. Cuddy

"The Lower Cretaceous McMurray Formation contains the bitumen reserves of the Syncrude Mine in northeastern Alberta. This formation comprises sediments deposited sequentially in fluvial, estuarine and marine depositional environments. The Syncrude Base Mine area consists mostly of estuarine sediments, as much of the original marine sediments have been eroded away. These estuarine deposits consist of channel-fill sediments and interchannel tidal flat sediments with the channel-fills comprising most of the orebody.Channel-fills contain, among other lithologies, interbedded sand, silt and clay rich layers that often occur as sequences of inclined beds with dips up to 25 degrees or more. A detailed knowledge of the distribution of these inclined beds, their lithological characteristics and their continuity is very important in assessing the risk of mine highwall instability . Techniques used to identify and characterize adverse structures are reviewed. INTRODUCTIONGeneralThe Syncrude Canada Ltd. oil sand mine is located within the surface mineable portion of the Athabasca Oil Sands area about 40 kilometres north of Fort McMurray in northeastern Alberta, Canada (Fig. I). The company commenced large-scale strip mining of oil sands in June 1977in the area, referred to as the Base Mine, situated in the southeast corner of the company's two lease areas (Fig. 2).The mining method (Fig. 3) utilizes large electric drag lines operating on a single bench with highwall depths up to 60 metres. Feed grade oil sand (= 6 wt.% bitumen) is mined by draglines and windrowed parallel to the highwall crest. Lower grade oil sand « 6 wt. 0J0 bitumen) occurring as waste bands is selectively mined by the draglines and cast back into the mined out pit or placed on the bench and hauled by truck. The windrowed feed is delivered to the extraction plant by a bucket wheel reclaimer and conveyor system. Stripping of Recent, Pleistocene and Cretaceous overburden units is done outside the conveyor systems by mobile equipment. The 4.5 kilometre long mine is split into four quadrants for planning and scheduling purposes, with each quadrant having an individual dragline-bucketwheel-conveyor system.Surface mining of oil sand at Syncrude requires the removal of vast quantites of material. The design of the open pit mine relies heavily on knowledge of the distribution of ore and waste materials, and on the physical characteristics of these materials.The geology of the oil sand below the dragline bench at the Syncrude Mine is complex. Geological, geotechnical and hydrogeological factors play an important role in the design and operation of the mine. This paper describes aspects of the geology that impact on the design and operation of the mine. Some of the methods and procedures adopted by Syncrude to successfully overcome difficulties that the complex geology creates are discussed."

Jan 1, 1989

By J F. Short

The jet piercing process, developed by Union Carbide Canada Ltd., is well established in blasthole production in open-pit mining. By this process, holes can be drilled, shaped and chambered for blasting. In suitable ore or rock formations, a considerable cost reduction can be achieved. This paper reviews the equipment used, relates how cost savings may be accomplished, and concludes with a mention of the most recent developments in this field. JET piercing and chambering, a process for blasthole production in open-pit mining, leads, in many instances, to improved drilling and blasting techniques and costs. It is a method of working rock with a supersonic flame and, to be most effective, depends upon a characteristic of the rock called spallability. Spalling, in this case, is the breaking away of surface particles from the rock body due to stresses caused by the thermal shock of the jet flame. Various rock properties contribute to this action, but, in general, the harder the rock the greater the spallability and the more effective and economical is the jet process. The jet process has the capability to drill, ream, shape and chamber holes for blasting.

Jan 1, 1965

By H. Hao

This paper outlines the development of a 2-D axisymmetric mathematical model to predict the evolution of temperature during the Direct Chill (DC) casting of AZ31 magnesium billets. Model predictions of temperature have been compared to measurements made on an industrial DC casting machine at Timminco Ltd, in Haley, Ontario. These measurements have been used to fine-tune the thermal boundary conditions employed in the mathematical model, The model, which is based on the commercial finite-element code ABAQUS, has been developed as part of a strategic project aimed at improving the DC casting process for light metals through a reduction in casting related defects and increased productivity.

Jan 1, 2004

By T. Thriveni, Ji Whan Ahn

"The current advanced technologies for the manufacture of light weight metals processing significantly increasing and attributes to the safety, performance, recyclability and economy. Still lack of technologies developed for light weight metals processing waste utilization and application. Environmentally friendly methods need to develop for better understanding the processing waste utilization. Alumina and aluminium processing creates a wide range of waste products, the most significant being is red mud. Bauxite residue is a high volume hazardous waste and nearly 3 billion tons have been dumped worldwide. Approximately, 120 Million tons/yr of red mud being produced without any environmental sustainable solution. Currently the most significant technology is waste utilization. The bauxite residue is suitable for road base construction, golf bunker sand, back fill and, general fill. Sustainable recycling technologies are necessary for the bauxite residue utilization for the recovery of rare earth elements and cement materials. Carbonation or CO2 sequestration of carbon dioxide is a method pioneered for the bauxite residue is modified to reduce alkalinity. The carbonation of alkaline material is an inexpensive and safe process that leads to the formation of thermodynamically stable products. The use of the carbonation can be an advantageous solution for environmental climate change and sustainability problems in the new century.INTRODUCTIONIn 2014, bauxite consumption was estimated to be 9.6 million tons, nearly all of which was imported, worth an estimated 269 million dollars. More than 95% of the bauxite was converted to alumina, and the remaining 5% went to non-metallurgical products, such as abrasives, chemicals, proppants, and refractories. Global aluminum demand is growing steadily spurred by growth in India and China (RBCAluminum Market Outlook, 2013) (Figure 1). Aluminum consumption is expected to rise 5% annually through the end of the decade, reaching 67 million tons per year by 2020. Global bauxite production decreased by 17% from that of 2013, principally owing to lower production in Indonesia. In response to a Government ban on exporting bauxite and other unprocessed mineral ores that took effect on January 12, 2014, bauxite mines throughout Indonesia shut down and production decreased from 55.7 million tons in 2013 to an estimated 500,000 tons in 2014. The ban was part of a mining law that was instituted in 2009 to increase development of downstream processing facilities in Indonesia."

Jan 1, 2016

By S. Hosseinpour

Chromate conversion coatings (CCCs) are usually applied to these alloys to enhance their resistance to localized corrosion and to improve paint adhesion. The special properties of these coatings such as their low electrical contact resistance (ECR) make them suitable for satellites. This study is aimed to develop advanced CCCs with the proper appearance, morphologies and surface roughness and to evaluate their role on the ECR and thermo physical properties on hardened aluminium alloy of Alclad-7075-T6. Coating characterization was performed by means of scanning electron microscope (SEM) and atomic force microscope (AFM). ECR of coatings were measured by special laboratory designed instrument and a and c were measured by Emissometer and Reflectometer respectively. In addition, corrosion performance of the CCC-coated alloys was determined by 168 hr exposing to salt-spray testing in accordance with ASTM-B117. The results of accomplished experiments on the developed CCCs in this study have been agreeable concerning available acceptability criteria for satellite surfaces.

Jan 1, 2007

By E. O. Reinbold, J. H. Johnson, D. E. Keski-Hynnila

A field laboratory for use in monitoring underground mine air quality has been developed and proven in underground service. The laboratory includes two separate monitoring systems and data analysis computer programs. One is the Mine Air Monitoring Laboratory (MAML). This is an enclosed trailer-mounted laboratory capable of monitoring CO2, CO, NO, NO2 particulate matter, S02, NH3, temperature and air velocity in the mine drift. The MAML can be up to 1000 feet away from the area being monitored. The second system is the vehicle data system, mounted on the load-haul-dump (LHD) vehicle, which monitors engine speed, engine fuel rack position, exhaust gas temperature, ambient temperature, vehicle speed, CO2 concentration near the operators' breathing zone and the mode of operation of the vehicle. The two computer data analysis programs and the two field instrument systems comprise a complete Mine Air Quality Laboratory (MAQL) for underground pollutant studies. Data from the systems have been used for studying vehicle duty cycles, ventilation systems, exhaust after-treatment devices, vehicle exhaust system design and portable instrumentation. Descriptions of the laboratory are presented along with a summary of some of the experiments performed. The capabilities of the lab are discussed, along with future potential uses.

Jan 1, 1981

By J. Mizera, J. Zdunek, K. J. Kurzydlowski, A. Dobkowska

This work concerns comparison of corrosion resistance of the aircraft aluminum alloy composed of Al - 2.3%Li - 0.1% Zr. The alloy was hot rolled (HR) from 13 mm to a thickness of 4 mm (e = 2.4) and 1 mm (e = 5.2). Corrosion resistance was investigated by Potentiodynamic Polarization Test. The investigation relied on exposure samples in two different corroding medium: 0.5 M NaCl solution and 0.01 M Na2SO4 solution with added 0.01% of Cl- at room temperature. Furthermore, the microstructure was analyzed using the optical microscope with polarized beam. The hardness was measured on lengthwise profile. It was stated that alloy after the largest deformation (equivalent total strain e = 5.2) is characterized by the best mechanical properties and the best corrosion resistance. The alloys in initial state and after deformation to 4 mm (e = 2.4) are characterized by worse corrosion resistance. It is associated with microstructure and density of dislocation in analyzing material.

Jan 1, 2015

By B. K. Gorain

Barrick' s Buzwagi copper-gold deposit in Tanzania comprises oxide, saprock and sulphide mineralized zones averaging approximately 0.058oz/t gold, 0.13% total copper and 0.03% cyanide-soluble copper. A comparative evaluation of the project based on two potential flowsheet alternatives is presented. The first flowsheet included a gravityconcentration and carbon-in-leach (CIL) plant. The second flowsheet was based on a Gravity-Flotation-CIL plant, which proved to be more economically robust. Selective flotation of copper minerals to produce a saleable copper concentrate proved to be challenging. Detailed characterization of the Buzwagi deposit was carried out through understanding of ore mineralogy, mineral liberation, floatability and selectivity, reagent chemistry and regrinding issues. With this insight, a flotation concentrate of greater than 25% Cu was achieved, recovering a significant amount of copper minerals and tellurides. The overall economics of the project improved significantly with the addition of flotation. Leach tests on gravity and flotation tailings showed an overall increase in gold recovery of approximately 6% for a Gravity-Flotation-CIL plant compared to that for a Gravity-CIL plant.

Jan 1, 2007

By Ivan Malinsky, Gérard Castonguay

"On a développé un procédé qui donne une fonte (2,3% C, 0,07% V) du V2O5 (99%) et un rutile synthétique (94% TiO2) à partir d'un minerai, dont les réserves au Québec sont importantes. Le procédé comprend les opérations suivantes: 1) la concentration magnétique du minerai (30% Fe, 9% TiO2 et 0,65% V2O5) pour produire un concentré (65% Fe, 7% TiO2 et 1,6% V2O5); 2) le smeltage du concentré aggloméré dans un four à arc, sans fondant, pour produire une fonte et une scorie (30% FeO, 40% TiO2 et 8,0% V2O5) qui contient plus de 95% du vanadium et du titane présents dans le concentré; 3) le grillage alcalin (37% Na2CO3) de la scorie suivi d'une lixiviation à l'eau et de la précipitation de l'hexavanadate d'ammonium à partir du filtrat; 4) la lixiviation du résidu par l'acide sulfurique pur ou usagé pour produire un rutile synthétique. Un estimé préliminaire de la valeur économique du projet laisse croire à sa rentabilité à la condition que l'investissement pour le smeltage soit inférieur à environ 400$/tonne de fer.IntroductionLes gisements de magnétites titanifères sont nombreux dans le monde. Ils consistent en une magnétite étroitement liée a l'ilménite, La teneur trop élevée en TiO2 empêche l'exploitation de ces gisements pour la production de fer. Cependant, dans certains cas, la magnétite a une teneur intéressante en vanadium qui peut rendre l'exploitation de ces gisements rentable. Aujourd'hui, les magnétites titanifères constituent la plus importante source de production de vanadium. On estime qu'environ 70% du vanadium produit provient de ces sources."

Jan 1, 1983

By T. Krumins, L. Zunti, R. Frischmuth

Titanium and titanium alloys are commonly selected for pressure oxidation autoclave vent piping and pressure control valve components, as well as autoclave internals, in high-temperature operations. In a vent application, titanium ignition risk is reduced by limiting oxygen concentration, and preventing high gas velocity gas impingement on surfaces. Oxygen concentration is dependent on the autoclave pressure and temperature conditions and therefore titanium ignition risk is dependent on standard operating procedures, and process control interlocks and permissive conditions. It is not uncommon for standard controls to be deficient during atypical operating conditions, or for operations to deviate from the operating procedures, increasing the potential for titanium ignition incident. Titanium ignition risk caused by elevated oxygen concentration in autoclave vent systems can be reduced with the introduction of an online autoclave overpressure calculation and the configuration of associated interlocks and permissive conditions.

Jan 1, 2014

By A. P. Williams

"This paper presents an overview of plant electrical systems in general, a discussion of the problems that may occur due to plant growth, the maintenance required to maintain the reliability and safety of the electrical system, and the selectivity of the relay protection system. It is divided into two main areas: short circuit levels within the plant electrical system; and relay protection systems.This information is directed at maintenance supervisors, mine managers and electrical superintendents who have been away from detailed short circuit and relay coordination calculations for some time. It points out the potential problem areas within an operating plant electrical system. Short Circuit LevelsTheoryThe electrical equipment in a plant such as breakers, switches and starters has two short circuit ratings, the momentary rating and the interrupting rating. These ratings may be given in MVA or current (amperes) depending on the equipment and manufacturer's preference. Since for a three-phase system MVA and amperes are related by the formula"

Jan 1, 1987

By A. G. Roach

MILLING of Nova Scotia gold ores began in 1862 with arrastras and wooden stamps and has progressed to heavier stamps followed by tables and other forms of concentration for the recovery of the sulphides. Chlorination and cyanide leaching of the concentrates has been practised, and in 1936 the combined amalgamation and all-sliming cyanidation plant of Seal Harbor Gold Mines was built. It has since been found that it is not necessary to cyanide the full tonnage and now only the concentrates are being so treated. From his experience in this enterprise, the writer presents the accompanying flow-sheet and supporting comments. While he has not the temerity to maintain that it is the best or only flow-sheet for Nova Scotia gold ores, he feels that it warrants thoughtful consideration by members of the milling fraternity of the Province. THE ORE The gold in Nova Scotia ores occurs both free and intimately associated with sulphides-chiefly arsenopyrite. Much of the free gold is quite coarse and crystalline. This is especially true when it occurs in white quartz. When in the slate, it is usually in thin plates and scales, frequently coated and discoloured. The values bound up in the sulphides are not amenable to amalgamation and must be recovered by other methods-concentration, followed by smelting or fine grinding and cyanidation. While high freight and treatment charges apply on concentrates shipped from the Province to smelters, a considerable quantity has been so disposed of in the past. However, it is hoped that a customs cyanidation plant will soon become available to producers of these auriferous concentrates in Nova Scotia.

Jan 1, 1938

By E. B. Spice

"IntroductionExperience at Eldorado has been gained with a variety of mill feeds. That is, the actual mode of occurrence of the pitchblende varies to such an extent that gravity concentration has at times been decidedly unattractive and at others highly successful. Because of this, the type of ore necessary for economic recovery of pitchblende have become well known. Also, those types which do not lend themselves to gravity concentration have become familiar. In general, it may be said that when the pitchblende occurs free, to a large extent, from sulphides or arsenides of high specific gravity, and when the bulk of the pitchblende is localized rather than disseminated, excellent recoveries, high ratios of concentration, and good grades of concentrates , will result from proper gravity concentration. On the other hand, if the ore contains pitchblende intimately or otherwise mixed with large quantities of arsenides or sulphides, or if the pitchblende is finely disseminated, gravity concentration alone will yield high recoveries only at the expense of very low-grade concentrates and low ratios of concentration.According to Taggart, the ease with which gravity separation may be effected is determined by the value of the following ratio: []It is stated that when the ratio is above 1.75, gravity separation can be expected to be easy. Thus with pure U308 (S.G. over 9) and gangue consisting chiefly of siliceous material, the process can he expected to be entirely successful even when carried on at very fine sizes. Unfortunately, the term pitchblende covers a great diversity of material. Although some of the mineral occurs pure enough to have a specific gravity of about 7, the average is much lower than this and is probably well under 5. Some of the pitchblende particles have a specific gravity so low that gravity concentration fails completely. It may also be said that no degree of grinding will produce free pitchblende of sufficient density from such particles. This, then, represents the most important limitation to the application of gravity separation to pitchblende ores."

Jan 1, 1950

By \/eena Sahajwalla, Alexander Blagus

This paper reports the effect of using High Density Poly-Ethylene (HDPE)/coke blends on the reduction behaviour of Mn3O4 to MnO at 1000°C. The results suggest that CH4 release increases with increasing HDPE addition. The results show that the rapid release of methane, over only the initial five minutes, limited the interaction of Mn3O4/MnO with CH4. With the devolatilisation of HDPE there was increased porosity in samples containing HDPE, assumed to be the major factor in differences of reduction rates.

Jan 1, 2011

By Unkown

The Province-wide road ban on movement of heavy loads has had the effect of curtailing or stopping development in several areas. In the Leduc area, the discovery well has been restricted in flow to only a fraction of normal due to limited storage space, but drilling at Imperial Leduc Nos. 2, 3, and 4 has been continued for the past few weeks. The No. 2 well is within 100 feet of the producing horizon and should be completed within the next few days. According to reports, it has been logging slightly lower, structurally, than the discovery well, but, regardless of the outcome, it has been an important test to determine westerly cross-section of the Leduc structure. No official reports have been made available of any tests made during the drilling of the well, but it is understood that promising oil and gas shows have been indicated in higher formations. Actual drilling operations have not been commenced by any of the other companies holding leases in the immediate area but it is expected that, when road bans are removed and equipment is assured, several wells will be commenced. Announcement has been made that Imperial Oil, Limited, will drill a well near Battle lake, about thirty-five miles southwest of the Leduc field. Location of the well has been made following an extensive seismograph survey of the area, with total depth of the test well expected to be in the 8,000- to 8,500-foot range. Drilling will be done with the heavy-duty rig last used at the De Winton test. Imperial Oil have abandoned hope of oil production in the Provost area after drilling nine wells, but will retain their interest in the gas field that has been developed. Of the wells drilled, four indicated gas flows ranging from 1,060 to 13,200 M.c.f. per day.

Jan 1, 1947