Search Documents

By H. E. Pawson

"COMMON METHODS OF ELIMINATION: The four methods most frequently used to dispose of cyanide wastes are:1. Oxidation2. Dilution with water or with cyanide free wastes3. Acidification and dilution of resulting gas with air4. Alkaline ChlorinationMost operators practice a combination of the first two methods, allowing oxidation and dilution of cyanide waste in tailings ponds. Then, pond effluent is introduced to a stream for further dilution andoxidation which is expected to take care of the cyanide. This method oftreatment does work to a certain degree. Atmospheric oxidation in tailings ponds and in receiving streams chemically breaks down the cyanide radical to form carbon dioxide and nitrogen.2(CN) + 202 2 CO2 + N2The monetary advantage to this method is obvious to the operator but too frequently though, climatic conditions are ignored. Length of winter, and reduced flow of the receiving stream in summer, adversely restricts the result of this combined method. For those of us who rely mainly on dilution it would be wise to remember that 70 million pounds of water are required to dispose of one pound of sodium cyanide (1).The third method outlined involves addition of acid in a closed vessel and venting resulting gas to atmosphere with or without air dilution by mechanical means. Cost, safety and some form of secondary treatment to complete destruction of cyanide remaining in the solution usually make this method prohibitive.The alkaline chlorination method is the one most commonly accepted for treating cyanide bearing wastes since it is felt that cyanide is completely eliminated in this manner."

Jan 1, 1973

By V. Coffin, T. Cienski

"(Figure 1) Reagentized pulp enters into the column at about 1/4 of the distance from the top. Inside the column it meets with a downward flowing stream of water and with an upward flowing mass of air bubbles. Flotation takes place in this counter current system while at the same time fine gangue particles are washed off the froth before it reaches the overflow lip at the top of the column. The main operating features of the column flotation are as follows:a) No moving parts. Solids are kept in suspention not by an agitating action of a propeller but by settling down against the rising air bubbles.b) Wash water. Spray pipes are installed a few inches below the froth surface and deliver required volume of water. The purpose of this water is twofold:(i) it keeps in balance the flow of material through the column and(ii) it washes rising froth in the froth layer as well as removes unwanted fines attached to the bubbles at the lower flotation section. As a result the concentrate produced is of higher purity than in the conventional flotation. Column is characterized by very high up-grading. However, even temporary disruption of wash water supply results in a drastic drop of concentrate grate.c) Flow balance. (Figure 2) For the correct operation volume of the underflow (tail) is larger than that of the feed. The difference is made up by the wash water. This difference called bias is predetermined and ranges from some 4 to 15 USGPM depending on the size of the unit and process requirements."

Jan 1, 1981

By K. Hoover, G. Labarre, S. Rantanen

"As part of the Namew Lake project a mill was constructed to treat 1900 tpd of ore grading approximately 0.90% CU and 2.45% Ni to produce copper and nickel concentrates.Nickel occurs mainly as pentlandite and violarite while copper occurs as chalcopyrite. Two main ore types are present1 lower grade disseminated sulphides in a talcose ultramafic gangue and a higher grade solid sulfide with a granitic breccia matrix.Primary crushed ore from underground is treated on surface in a conventional closed circuit crushing plant using 2-stage cone crushing. Crushed ore is conveyed to storage and then fed at a controlled rate to a grinding circuit employing a rod and ball mill with hydrocyclone classification. Rougher flotation separates and cleans nickel and copper sulfides from waste materials followed by a high lime separation circuit to separate the minerals into final concentrates. Dewatering is achieved through use of high capacity thickeners and pressure filters prior to delivery to a loadout area. The crushing and milling control is highly automated.Plant design was based on metallurgical samples obtained from drill cores. After the first year of operations, plant results compared favourably with design projections.INTRODUCTIONThe Namew Lake Project is a joint venture partnership between Outokumpu Mines Ltd. (Canada) and Hudson Bay Mining and Smelting Company Ltd. (60%). The project included construction of a mine and milling complex to treat approximately 500,000 tonnes per year of copper-nickel ore grading o.91% and 2.44% Ni. Known reserves are estimated at 2. 65 million tonnes. The deposit is located approximately 65 km south of Flin Flon (120 km by road) and about 5 km east of the Manitoba-Saskatchewan border. The decision to construct a concentrating facility was made June 15, 1987 and construction started a week later. The facility, designed for 1900 tonne per day throughput, was ready for commissioning in September 1988. Outokumpu Engineering of Finland was chosen to prepare metallurgical flowsheets, select and develop plant layouts, and provide construction management. Kilborn (Toronto) contributed detailed engineering for civil, structural, mechanical and electrical components and outokumpu Equipment of Canada, the design, the supply, and commissioning of the instrumentation package. Hudson Bay undertook the initial metallurgical test work and preliminary design work."

Jan 1, 1990

By Christopher McElman

Real-time mine management solutions have evolved over time from closed, proprietary solutions, to a "system of systems" that may include a wide variety of off-the-shelf components and technologies. Modular Mining Systems has embraced open standards for their NextGen products to bridge the technology gaps between these systems. However, the remaining logical gaps must be overcome, in order to achieve truly seamless integration between discrete systems. When dealing with volatile real-time management problems, the effectiveness of business process modeling and middle-ware can break down. Scientific principles of military command and control applied to mining domain help to achieve better alignment and reach the highest level of integration. The combination of open standards and off-the-shelf hardware and software with a deliberately structured command-and-control approach provides a clear evolutionary path from ad-hoc connected systems towards real-time management of a seamlessly integrated digital mine.

Oct 1, 2009

By P. J. Gron

"The Samatosum Project is a base and precious metal deposit located in south central British Columbia. A dilute ore reserve of 766, 682 tonnes grading an average 1.1% copper, 3.0% zinc, 1.4% lead, 833 gram per tonne silver and 1.6 gram per tonne gold is available. The base metals occur as tetrahedrite, chalcopyrite, sphalerite and galena. Virtually all of the silver and gold are associated with the tetrahedrite.The mill is operated at a rate of 21 tonnes per hour. Sulphur dioxide is used as a zinc depressant in the grinding circuit. Production of a Cu/Pb/Ag concentrate is accomplished by conventional flotation. This concentrate is then separated into Cu-Ag and Pb concentrates through a reverse flotation circuit utilizing sulphur dioxide, starch and sulphuric acid as lead depressants.The tailings from the Cu/Pb/Ag circuit are treated with copper sulphate to activate the zinc. Production of a zinc concentrate is accomplished by conventional flotation. Dewatering of the concentrates to 6% moisture is done with a LAROX filter press.Tailings effluent is treated with lime and sodium sulphide to precipitate out the heavy metals. The resulting sludge is treated in OYNASAND sand filtration units to produce a quality effluent."

Jan 1, 1990

By B. Lueger, D. Shen, M. Sedighy, R. Rand, R. Saleh, J. Cheung, M. Rifai, I. Khan, W. Sauri, D. Setianto

The world’s first active power demand stabilization system for a 3-electrode electric arc smelting furnace was commissioned at PT Vale Indonesia in December 2012 on Furnace No. 2 using an SPLC (Smart Predictive Line Controller). The SPLC technology in combination with the Furnace No. 2 rebuild and other upgrades has enabled PT Vale to increase the electrical input to the furnace by up to 20% on a stable and sustainable basis by eliminating peak powers that overload and trip out the electrical equipment, and by reducing power unbalances. The SPLC technology maintains smooth arc power using a continuously variable thyristor controlled series reactor. The SPLC compensates variations in the furnace arc with predictive changes in the circuit reactance at a speed of up to 60 times a second. The system started up quickly and has been shown to be easy to operate and maintain by PT Vale. PT Vale’s Operations Team has been testing the new system at set points of up to 90 MW on the newly re-built Furnace No. 2. Over the last 12 months, the throughput of Line 2 has increased by approximately 10% on an annual average; however, debottlenecking in other design areas of the operation is required in order to achieve 90MW operation on a sustainable basis. This outstanding success results from a combination of the furnace and other upgrades, the SPLC active power stabilization, and the skill of PT Vale in quickly adopting new technologies and maximizing the combined benefits of each technology in their operation.

Jan 1, 2014

By J. Lammers, D. Adams

Most pressure oxidation operations introduce oxygen through a large multi-use nozzle in the vapour space of the autoclave. Sparge pipes extend inside the vessel to the point of discharge below the compartment agitator. However, two zinc pressure leach operations have successfully used a bottom entry oxygen sparge system for a number of years. Recently, the concept has been used in a whole ore gold pressure oxidation operation as well as a copper pressure leach plant. Both of the latter operations also introduce cooling water for temperature control through the same sparge pipe. This paper addresses the benefits of the bottom entry system with regards to autoclave performance and the positive effects on agitator performance.

Jan 1, 2004

By J. C. Salas, A. Weishaupt, J. A. Guzman

The origins of the electrorefining process date back to 1869, when the first ER cathodes were produced at Pembrey, South Wales. By the time that Pembrey was closing, Chuquicamata tank house was under construction, initiating in 1915 a long history of electrolytic cathodes production. Initially electrowon cathodes and later electrorefined cathodes were produced. During the history of Chuquicamata tank house, there have been several challenges associated with the quality demanded for electrolytic copper. Among them, the transformation from electrowinning to electrorefining in 1952, the onset of the direct commercialization of ER cathodes and the phase out of wire bars in the 80s, several technological changes including the implementation of permanent cathodes, and certainly the constant increase in complexity of the anodes refined. This paper explores the manner in which Chuquicamata has addressed these challenges and examines its links to process characteristics, which have been necessary to maintain a product quality according to market requirements and a brand, “CCC”, that is widely recognized worldwide. INTRODUCTION Located in the north of Chile, in the Atacama Desert, Chuquicamata is an open pit copper mine that for many years has played a relevant role in the global and local mining industry. Known from prehispanic times, the Chuquicamata deposit was initially developed between 1912 and 1915 by the Chile Exploration Company, the operating company of the Chile Copper Company controlled by the Guggenheim Brothers in the USA (Yeatman, 1916). Officially inaugurated on May 18th, 1915, by the President of Chile who pressed a button in Santiago sending a telegraph signal to the power generation plant specially built in Tocopilla, 1500 km north. It signaled the beginning of generating energy, sending it to Chuquicamata, another 140 km east (“El mineral de Chuquicamata”, 1915), marking the beginning of its industrial operation.

Jan 1, 2019

By C. C. Allen, H. H. North

"The Young-Davidson mine is in the southeastern part of Powell township, in the district of Matachewan. It is 32 miles southwest of Kirkland Lake, 48 miles southeast of Timmins, and 25 miles by road Northwest of Elk Lake. The Young-Davidson and its neighbour, the Matachewan Consolidated mine, are the two present producing properties in the district. The Matachewan area is the southwestern extension of the Kirkland Lake belt or 'break'. The Young-Davidson mine since coming into production in 1934 has been operated by Hollinger Consolidated Gold Mines, Limited. ""Desultory prospecting(1) has been carried on in the Matachewan area from time to time since the discovery in 1906 of silver in James township at Elk Lake, and some gold has been found in the southeastern part of Alma township and in the central part of Cairo township. The first real interest in the area, however, was started by Jake Davidson's discovery in 1916 of gold on Davidson creek, on what is now part of the Young-Davidson property, and by Sam Otisse's discovery shortly afterwards on claims a short distance to the east, now part of the Matachewan Consolidated property. In subsequent years both of these properties were investigated by various companies; the Young-Davidson chiefly by the Porcupine Gold fields Development and Finance Company, Limited, and the Matachewan Canadian by the Colorado-Ontario Development Company, Limited, which in 1919 was reorganized under the name of Matachewan Gold Mines, Limited. Work was discontinued as the ore was considered too low in grade to be mined"". However, in 1933 Hollinger Consolidated Gold Mines, Limited, undertook to bring the property into production and this became a reality in 1934.The total production to the end of year 1945 was 319,185.59 oz. gold and 73,541.94 oz. silver from 3,228,845 tons of ore. This represents an average grade of $3.67, including exchange and premiums."

Jan 1, 1954

By J. Kronsteiner, E. Kabliman

"In the present work, we developed a Smart Process Control Toolkit (SProC) as a single simulation environment for the modelling of materials microstructure and its interaction with the local microchemistry during manufacturing of semi-finished products. This toolkit supports the data communication between sub-sequent processing steps such as casting, homogenization, pre-heating to deformation, etc. The thermo-kinetical simulation software MatCalc of MatCalc Engineering© GmbH was used for modelling of precipitation kinetics, such as formation of primary and secondary phases and their evolution. An import/export functionality of the precipitation distribution after each processing step was implemented to follow the parameter history. For the evolution of the local microstructure, a Mean Dislocation Density based Model (MD2M) was used. This model consists of two parts: (1) Flow Stress Model for calculation of the total strength during the deformation and (2) Static Recrystallization Model for account of the recrystallization and grain growth after the deformation. Validation was done by a comparison of experimental and simulated hot compression tests of a conventional AA2024 alloy.INTRODUCTION Optimization of a semi-finished products quality, elimination of typical production issues and cost savings are of a great demand for supply industries. However, it is currently not feasible to investigate the whole manufacturing process in detail at an industrial level. Concerning the processing parameters, one must understand the correlation mechanisms between macroscopic properties and microscopic material behavior. Numerical simulations, which could reproduce the real processing conditions on the one hand, and employ a physically based modelling on the other, are thus attracting a lot of attention and their power is no longer under the question. It is well known that e.g. the total strength of the material depends directly on distribution of precipitation particles and mean grain size. In order to follow their evolution during the manufacturing process beginning from casting to the final semi-finished product, and thus be able to control the process, one should use the techniques which would at the same time reproduce experimental processing conditions of real size objects (e.g. sheet, extrusions, etc.) and account for the evolution of a local microstructure and its interaction with the microchemistry. A commonly used approach is to implement a model which would describe the evolution of microstructure based on a dislocation density approach into a user defined material subroutine of some finite element solver. There is, however, also an influence of the manufacturing process by e.g. the evolution of a local microchemistry (formation, transformation and dissolution of the precipitation particles) on the microstructure and thus the macroscopic material behavior. Thus, a method is needed to follow the variable history through the simulation of the whole production chain."

Jan 1, 2018

By W. J. Kuit

"Complex facilities which provide for the collection, management and treatment of effluents emanating from the Sullivan mine and concentrator tailings were made operational in October 1979. Key features of the system are the use of upgraded tailings ponds for the storage of up to 800 million litres of metals-contaminated effluents, a treatment plant employing lime in a high-density sludge process and a sludge-impoundment facility designed for maximum long-term environmental safety. The completed works are capable of satisfying a difficult range of operating requirements imposed by highly variable weather conditions, drainage flows and soluble metals loadings. Final capital expenditures for the project approached $10 million and annual operating costs are about $0.8 million.This paper discusses the Kimberley effluents treatment project and the major considerations in its development. The treatment process, major plant equipment and initial operating experience are also described.IntroductionCominco Ltd. has worked the Sullivan orebody at Kimberley, B.C. since 1909 and has operated a concentrator some 5 km distant from the mine since 1923. Over the last 70 years, in excess of 120million tonnes of ore have been mined, and production continues at an average rate of 6,500 tonnes per day. It is a well-known fact that the contribution of this operation to Canada's mining industry and, in particular, Cominco's development has been significant. However, this success has not been without some undesirable side effects.Unfortunately, the Sullivan is one of only a few major Western Canadian orebodies which may be classed as ""acidic"" in nature. That is, the primary economic minerals, galena and marrnatite, are enclosed in a siliceous host rock with abundant pyrrhotite, but with little or no accompanying alkaline gangue minerals such as calcite and dolomite. The unavoidable consequence of mining such an ore is that contact with air and water generates an acid mine drainage containing various soluble metals orginally present as minerals.This problem also arises in the concentrator's tailings ponds, which, in the case of the Sullivan, are two separate impoundments of different materials. The 1,100 tonnesl day of ""iron"" tailings are primarily pyrrhotite which is surplus to the requirements of a separate operation that produces sulphuric acid as an intermediate to phosphate fertilizers. Inert gangue minerals with only a minor sulphide content are the main constituents of the 1,200 tonnes/ day of siliceous tailings. Corresponding to the relative proportion of sulphides in the solids, the decant from the iron tailings is substantially more contaminated than that from the siliceous pond."

Jan 1, 1980

By P. Carlone, A. Astarita, F. Rubino

Cold gas dynamic spray is an innovative technology allowing the deposition of thin metallic layers on a bulk or sheet substrate. Titanium on aluminum deposition is very attractive to the aeronautic industry, due to the enhanced corrosion resistance and wear properties of titanium coating as well as its improved compatibility with CFRP, preserving the reduced cost of aluminum substrate. One main drawback, however, is related to the micro-porosity of the deposed layer, negatively affecting the corrosion barrier performance. In this paper, the effect of selective laser post-treatment on pure grade 2 titanium coatings on AA2020-T3 sheets was experimentally and numerically investigated. Morphological features, microstructure and chemical composition of the treated zone were assessed by means of optical microscopy, scanning electron microscopy and energy dispersive X-ray spectrometry. Microhardness measurements were also carried out to evaluate the mechanical properties of the treated coating. A numerical model of the laser treatment, based on a finite volume scheme, was implemented and solved to simulate the process and discuss the experimental outcomes. Obtained results highlighted the key role played by heat input and dimensional features on the effectiveness of the treatment.

Jan 1, 2015

By Galen Bauer

"Up until the mid 1960's, the only available methods for making continuous weight measurements were through the use of mechanical and electro-mechanical weigh scales. It was during this time period that a new concept in weighing was introduced. It was known and is still known as the nuclear belt weigh scale.During the early days of its appearance in the market place, many things were learned about its advantages and disadvantages for weighing various materials. As with many new devices, it had to go through a ""wringing out stage"" before it became accepted by the weighing industry. Even today, even though it is a proven device, there are skeptics who believe the nuclear belt weigh scale will not survive. Let me assure you, it is here to stay.. 'PRINCIPLE OF MEASUREMENTThe nuclear belt weigh scale consists of a ""C"" Frame assembly which houses the radioactive source (Cesiwn 137) and the radiation detector (Ionization chamber). The ""C"" Frame assembly is put in place around the conveyor belt as shown in Figure 1. The radiation source emits a fan shaped beam of radiation which covers the full width of the material being conveyed on the belt. Radiation which has passed through the material on the belt is detected by the ionization chamber which is located in the lower arm of the ""C"" Frame assembly. The ionization chamber changes the radiation energy into an electrical signal which is related to pounds per foot belt loading. This signal is transmitted to a highly stable amplifier which combines the pounds per foot signal with a belt travel signal from a digital tachometer which allowed the scale user to be able to monitor total mass being conveyed. Many so-called conventional type scales use belt speed rather than travel to obtain mass per unit time, and then integrate the signal to obtain their weight signal. This unnecessary step tends to erode the overall accuracy of the weighing system."

Jan 1, 1975

By J. D. Nye, I. A. Farr, W. J. D. Stone

"A unique deposit of barite exists near Brookfield, Nova Scotia. The crystals are extremely fine and the whole deposit virtually free of heavy metals. The deposit size was not large enough for conventional uses, such as the production of barium carbonate and drilling mud. In an effort to obtain maximum utilization, a program was begun to determine if U.S.P.-grade pharmaceutical barium sulphate for X-ray diagnosis could be produced. Early work was sufficiently encouraging to institute a development program under the federal Program for Advancement of Industrial Technology. This has been very successfully completed. Canadian and U.S. process patents have been issued, clinical trials have been successful, a production plant has been designed and the plant’s production sold. The processing plant will include magnetic separation for the removal of iron minerals, fine grinding by paddle milling to minus one micron and acid leaching. The process is unique in that at no time is the barium taken into solution.Information is given on the deposit, process, markets, use, plant capital and operating costs, and projected profits. The initial production plant will have an annual capacity of 2,000 tons per year of end product. Capital cost is $850,000 and annual turnover more than $1.5 million. As this capacity only represents approximately 15% of the North American market, rapid plant expansion is foreseen."

Jan 1, 1980

By G. W. Diehl, G. A. Griffiths

"Gentlemen, one week ago, I attended the University of Minnesota's Annual Symposium on Mining, in Duluth. A good part of this symposium was dedicated to mill linings of rubber.At this symposium, three mining companies published results from long time full scale tests with rubber linings in mills at four different mines. These were the Republic and Empire Mines of Cleveland Cliffs Iron Company, the Groveland Mine of Hanna Mining Company and the Eagle Mountain Mine of Kaiser Steel Corporation. These papers will be printed in due time and I will not endeavour to relate their full contents, let me only say that in three of the plants, the linings were found to be very economical compared wi.th steel, and that these three are converting over completely to rubber linings, while the fourth, Empire Mine, reported no economical results as far as the shell lining goes, whereas the grates showed promise of becoming economical. The authors of the Cleveland Cliff's paper, however, stated that design improvements in the rubber lining possibly could result in an economical lining also for Empire Mine.That rubber linings in mills, in most cases, show better wear life than steel linings, is known by most of the audience. But, one thing that has not before been disclosed by the endusers is the effect of rubber linings on the grinding economy. All three papers mentioned above reported no change in capacity or grind and two of them reported a decrease in power consumption per ton ground. Hanna Mining reported an average decrease over a three year period for one mill of over 10%. This, of course, puts the economy of a rubber lining in a completely new light. Finally, a point of interest at this meeting was that all three papers emphasized the design aspect, Thus the industry has acknowledged what I believe to be a very important fact - the design of a lining is often more important than the material it is made of."

Jan 1, 1970

By Turgut Yalcin

"High-grade concentrates are achieved in flotation columns primarily due to the use of thick froth layers and wash water, both of which facilitate the drainage of hydrophilic minerals from the froth. However, conventional columns employ tall, non-agitated recovery sections for bubble-particle attachment that require high headroom and special gas spargers as well as imposing particle size limitations. These disadvantages can be all alleviated by carrying out the recovery part of the process in a mechanical or pneumatic cell which generate froth more conveniently and efficiently.This paper describes the combining of mechanical and column flotation in a single unit and discusses the influence of various parameters on the performance of the system.INTRODUCTIONIn a flotation process, some of the minerals lifted up to the froth phase may drain back to the pulp due to various reasons such as weak attachment of particles to air bubbles, bursting of air bubbles, agitation of froth, etc. Weakly floating and entrained hydrophilic minerals drain at a faster rate than the strongly floating minerals, and effective exploitation of such differential drainage can lead to cleaner concentrates.For a given mineral, if the rate of flotation from pulp to froth is k1 (min·1) and the rate of drainage from froth to pulp is k2 (min""1), then the net (overall) flotation rate of the mineral, k (min-1 ), will be [Lynch et al., 1981 ]:"

Jan 1, 1997

By Dave Thomas

?Uranium is a common trace metal at the earth?s surface, but these are amazing super-high grade (up to 25%) pods, veins and disseminated uraninite (UO2) near unconformities between Proterozoic siliciclastic red beds and metamorphic basement with graphitic metapelite and radiogenic granite. ?Pitchblende fills extensional features in reactivated fault zones and replaces matrix in sandstone ?One mining district in Canada ?the Athabasca Basin ->30 deposits /prospects -most in eastern ¼of basin -produces 1/3 of world?s U -employs northerners -VERY high tech -VERY high safety standards Unconformity-associated uranium depositsUnconformity-deposits

May 1, 2006

By L. M. Cumming

"The contact between dolomite of the St. George formation (Cambro-Ordovician) and limestone of the overlying Table Head formation (Middle Ordovician) is a regional disconformity. This is best illustrated from exposures on Pointe Riche Peninsula, near Table Point, and along Port au Port Bay. The contact occurs along 180 miles of the west coast of Newfoundland from St. John Island in the north to the western part of Port au Port Peninsula in the south. A disconformity of the same age occurs between the Romaine and Mingan formations on the north side of the Gulf of St. Lawrence.Dolomitic beds beneath the disconformity locally contain concentrations of base-metal sulphides. Sphalerite occurs in dolomite pseudobreccias of the St. George formation at Zinc Lake, 7 miles northeast of Daniels Harbour. The 'Western Newfoundland Lower-Middle Ordovician regional disconformity is interpreted as having originated on and near the edge of a broad platform, and to have provided an important regional geological control in the localization of zinc mineralization."

Jan 1, 1968

By B. Tiryaki, M. Ayhan, O. Z. Hekimoglu

Coal shearers are one of the major sources of dust and fines in underground coal mines. Despite considerable research investigations, no comprehensive in situ investigations coupled with extensive laboratory studies on the effects of drum design on generation of dust and fines have been found. It may be for this reason that many major shearer drum manufacturers persistently employ a certain drum-lacing pattern on current coal shearers, which is believed to cause excessive dust and fines in coal mines. This paper shows how respirable dust and fines are minimized under near-identical conditions when the drum lacing pattern was changed from a triple-tracking to a single tracking arrangement. A series of laboratory trials simulating in full scale the practical cutting action of tools was followed by extensive long-term underground trials during production operations in OAL (Cayirhan) Lignite mine in Turkey. The results are presented and discussed, and recommendations for proper drum-lacing in terms of respirable dust and fines are made.

Jan 1, 2002

By L. C. Lien

Tower crane layout (TCL) is a typical construction site layout (CSL) problem, which is suitable for a wide range of work assignments and site conditions. Tower crane is one of the key facilities for vertical and horizontal transportation of materials, especially for heavy prefabrication units such as steel beams, ready mixed concrete, prefabricated elements and large panel formwork such as machinery and equipment, and a wide variety of other building materials within a construction site. However, it is a difficult combinatorial optimization problem to determine the locations of tower cranes with materials quantity supply and demand for engineers. Swarm intelligence (SI) was very popular and widely used in many complex optimization problems which was collective behaviour of social systems such as honey bees (bee algorithm, BA) and birds (particle swarm optimization, PSO). This study applied a hybrid swarm algorithm namely particle bee algorithm (PBA) based on a particular intelligent behaviour of honey bee and bird swarms by integrates theirs advantages. This study compares the performance of PBA with BA and PSO for a proposed hypothetical construction engineering of TCL with materials quantity supply and demand problem. Results show that PBA performs better performance than the mentioned algorithms on a proposed hypothetical TCL problem.

Aug 1, 2013