Search Documents

By Louise Pearce

?Environmental and social impact assessments (ESIAs) are: ??process-driven and scientific processes ??The process entails a number of steps and procedures which result in obtaining a licenceto operate ?and moving more towards a social license to cooperate. ?However, the primary premise of ESIA is to facilitate the consideration of environment and the communities in planning and decision-making which would ultimately make it possible to arrive at decisions that are ?sustainable?. ?Hence, ensuring the development of the mining sector on a sustainable basis is a critical challenge that needs to be addressed by the global community.

May 1, 2011

By L. Klatzel-Mudry, D. J. Nikols, J. D. Hughes

"The Geological Survey of Canada Paper 88-21, A Standardized Coal Resource/Reserve Reporting System for Canada, is referenced by National Instrument 43-101 for the preparation of resource and reserve estimates on coal deposits. However, for all disclosure of mineral resources or mineral reserves for coal, issuers are required by NI 43-101 to use the equivalent mineral resource or mineral reserve categories set out in the CIM Definition Standards and not the categories set out in Paper 88-21. “Because the framework is based on Canadian deposits and their tectonic regimes, the Canadian Securities Administrators believe it is not reasonable to apply Paper 88-21 to foreign coal properties. The “Resource Links” at the end of this volume provide website links to guidance documents for preparing coal resource and reserve estimates in Australia, South Africa, and the USA.”This report discusses definitions, concepts and parameters used to determine coal resource and reserve quantities, and provides a framework to facilitate consistent categorization of coal quantities found within various depositional and tectonic regimes in Canada.Coal deposits, or portions thereof, are first categorized in terms of their geological complexity <Geology Type), and probable recovery method (Deposit Type). Methods for determining quantification parameters including seam thickness, areal extent and bulk density are outlined for each geology/deposit category. Within each geology/deposit category, coal resources are further divided, based on their assurance of existence, into measured, indicated, inferred and speculative subdivisions and, according to their feasibility of exploitation, into immediate and future interest subdivisions. Coal reserves within each geology/deposit category are subdivided according to whether they are within or outside active mining areas, and may be reported on in place, recoverable and saleable bases.A wide cross-section of the coal industry in Canada contributed to the development of this reporting system. To ensure that the parameters and concepts expressed in the system continue to reflect technological and economic realities in the future, the Coal Association of Canada has established a committee to facilitate periodic reviews."

Jan 1, 2003

By Christine Hansen

?Kiss my Asteroid? Unofficial Title Human life is tied to minerals It?s worth noting that: The living human body consumes minerals. The minerals we take in multivitamins show the close linkage between human beings and mineral resources. Unlike tourism or specialized manufacturing, a human being could not live without mineral consumption. Minerals and their consumption is a tangible part of human life.

May 1, 2013

By A. Roca, V. A. Quezada, O. A. Benavente, M. Cruells

The leaching pretreatment of copper ores is widely used in the Chilean mining industry. Agglomeration and acid curing have been identified as the most useful pretreatments. Of these, acid curing was recognized as beneficial in the dissolution of copper minerals, even in sulphides such as chalcopyrite. Extensive acid curing times have an impact on copper extraction, generate a homogeneous acid distribution in the mineral bed and benefit the inhibition of aluminum-silicate minerals (acid consumers). This document describes some of the theoretical background and results regarding the effect of acid curing in a chalcopyrite sample with 74% purity according to Qemscan analysis and a 28.5% of total copper. Leaching tests are carried out at 25, 50 and 70°C, evaluating the effect of a pretreatment on the chalcopyrite dissolution. The original sample and products generated were characterized by X-ray diffraction analysis and Scanning Electron Microscopy (SEM). The performed experiments indicate a direct relation between the effect of curing time and temperature in copper extraction. 92% of copper can be extracted in a leaching at 70°C and with 15 days of curing. Elemental sulfur, jarosite and copper polysulfide (CuS2) have been detected in leaching products. INTRODUCTION The copper extraction from minerals is a technique that has been developed for hundreds of years in the world. In 2017, the largest copper producer was Chile, exported 5.5 million tons (COCHILCO, 2018). However, in order to preserve this production level means overcoming multiple challenges. In the case of the Chilean copper deposits, the average copper grade in 2016 was 0.65%, lower than the 1% declared in 2004 (Consejo Minero, 2018). This is mainly due to the deeper of the deposits reaching sulfide mineral zones, mainly chalcopyrite. Traditionally, these sulfurized zones ore are treated through concentration by flotation and subsequent pyrometallurgical treatments. However, for some copper companies it is complex to process by this alternative, due to the high costs and high rates of water consumption. The mineral resources of these companies are known as "low-grade sulfides" and do not allow, economically, the treatment of these minerals through concentration by flotation. This is how hydrometallurgy becomes an alternative for the treatment of this type of deposits. In addition, several companies have hydrometallurgical plants, which would allow the operational continuity of these plants.

Jan 1, 2019

By Prodipto Ghosh

This paper is prepared as a review of existing and traditional methods related to electrical maintenance strategy. Its primary focus is to explore newer ideas and how they point the way to a more efficient and effective manner of electrical maintenance. This discussion is primarily related to large electrical distribution assets typical of heavy industry such as mining.

Aug 1, 2013

By Garth D. Kirkham

The Problem The Don deposit is a series of two sub-vertical zones that pose a number of challenges with respect to modeling and interpolation. The first challenge is that, based on data and observations, the mineralization and, more importantly, the grade is layered or banded and is stratigraphically controlled. The second challenge is that, due to the undulations of the deposit and extreme changes in dip, using a standard oriented ellipse to guide the estimation process is not appropriate and does not result in an estimate that is representative on a local scale. In order to solve this problem an adapted methodology of relative elevation modelling, has been devised to effectively model and estimate deposits faced with these challenges. Relative Elevation Designed for bedded seam and gridded surface With variable dip and vertical grade variability

May 1, 2013

By Robert E. McIvor

"“Classification System Efficiency (CSE)” is a powerful, emerging tool that can be used to increase grinding circuit efficiency. It is defined as the percentage of the ball mill energy being used to grind target, oversize particles. The discovery, validation and current use of CSE, including how it was manipulated, are described through seven plant case studies. These resulted in efficiency improvements ranging from 3 to 30 percent, along with major reductions in over-grinding. The achievable CSE for any given circuit is described. This paper demonstrates both how, and how much, every plant can benefit from increasing grinding circuit CSE.DEFINITIONS: BALL MILL CIRCUIT “CLASSIFICATION SYSTEM EFFICIENCY (CSE)”, “EFFECTIVE MILL GRINDING POWER”: “WASTED/OVER-GRINDING MILL POWER”The closed ball mill circuit is shown in Figure 1. The extreme importance of the circulating load ratio in determining circuit productivity was demonstrated by Davis (1925) and re-published by Guadin (1939), as shown in Figure 2. The circuit production rate increases with increased circulating load ratio, rapidly so at first and continuing to increase more gradually with higher and higher values of circulating load ratio.The underlying cause of this relationship was seen when comparing the ball mill feed and product size distributions from two different ball mill circuits, one with a low circulating load ratio, and one with a high circulating load ratio (Figure 3). While the F80’s and P80’s of these two circuits were close to the same, the mill feed and discharge size distributions were quite different. The ball mill in the circuit with the higher circulating load ratio contained a substantially greater fraction of material coarser than the target P80, as indicated by the respective mill feed and discharge size distributions. This fraction represents the fraction of the mill power being expended on “coarse” (in this case, plus P80 size) material, or the circuit “classification system efficiency.” The “effective mill grinding power” is the total mill power multiplied by the CSE. The compliment of CSE, the remaining fraction of “fines” in the mill, is the fraction of the mill power being wasted, and spent on over-grinding of material already finer than the circuit target product size. This is the “wasted/over-grinding mill power”"

Jan 1, 2013

By C. Samuelsson, H. Ahmed, B Björkman, A. Andersson

The cost of raw material and energy is a continuing driving force towards working with increasing the recycling of ore based steelmaking residues. In Sweden no on-site sinter plants are operated at the integrated steelworks. Instead, selected residues from the plant are incorporated in a cold bonded briquette product which is recycled to the process via the blast furnace (BF). Since the BF sludge is the major bleed of zinc out of the furnace it is required to be de-zinced prior to recycling in the briquette product. In the present work landfilled BF sludge has been characterized with respect to chemical composition, particle size distribution, X-ray diffraction (XRD), and scanning electron microscopy (SEM). The sludge was also subjected to laboratory scale hydrocyclone trials aiming at reducing the zinc content making the sludge viable for recycling. The results suggested that the sludge had been agglomerated prior to the characterization and hydrocyclone treatment. The zinc removal using the hydrocyclone was discussed.

Jan 1, 2015

By A. J. W. Law

"This paper deals with the organization of the central office technical areas and the role played during the feasibility studies, construction and operating phases of Les Mines Selbaie.HistoryThe Engineering Department was originally formed as a part of the Exploration Department, to examine the feasibility of advanced exploration prospects being brought to the company. In 1968, with the discovery of the South Bay property in northwestern Ontario, the department became part of a Mining Division and was expanded, so that it could provide more advanced mine feasibility studies, control of construction engineering and procurement and initial mine design. As is generally the case, the mine design function was handled with in-house capability, while plant, mill and const ruction functions used outside consultants.The 1974 discovery of the Selbaie deposits, started a period o f growth in the capabilities o f the department. The complex nature of these deposits, required that skills were added in the mining, metallurgical and plant areas. During the early feasibility study period these skills were provided by the engineering company of the parent group, but when it was realized that production from the deposits was likely, permanent staff was added."

Jan 1, 1990

By S. Vaidya, R. C. McKellar, N. K. Sinha

Nominally [001]-oriented nickel-base single crystal (SX) superalloy CMSX-10 was investigated at 900°C under constant load, equivalent to an initial stress of 700 MPa, for creep strains from 7% to fracture strain (18.2%). The cross-sectional dimensions of initially uniform cylindrical specimens were measured along their entire length after the tests. The cross-section changed from circular to near elliptical shape. The anisotropic deformation, measured in terms of eccentricity, increased with the increasing strain level, but for a given strain level, it remained constant along the entire length of the initially uniform gauge section. The results are discussed in terms of diameter, eccentricity, area, local stress and microstructural observations. The most striking observation was the fact that all the specimens displayed a yoke-like shape, or the reduction of cross sectional area, at two locations within the originally uniform gauge section. Such observations have not been reported in the literature for single crystal superalloys.

Jan 1, 2006

By Han Xing, Cui Jianzhong, Qin Ke, Shao Bo, Zhang Haitao

In this paper, a new approach that uses hot-top DC casting process to producing multi-alloy ingots is present. The different type and size of composite and coated ingots (4045/3004/4045 three-layer composite ingots with section 630mm by 1500mm and 4045/3003 coasted ingot with F140mm/F110mm in diameter) are cast by this approach. The macro-morphologies and microstructures of the composite ingots, the temperature distribution and the element distribution in the interface zone were investigated, also and the interface bonding strength was measured. Results show that the solid supporting layer formed on the cooling plates plays a key role in the casting process of composite ingots. The solid supporting layer can prevent the blending of two melts by resisting the impact of alloy melt, which ensures the stable casting process and casting high quality composite ingots, because the contact height is increased using hot-top DC casting. In addition, fabrication and properties of 4045/3004/4045 three-layer composite ingots with section 630mm by 1500mm are reported in detail.

Jan 1, 2015

By C. A. Young

"The stabilization of tailings has been a matter of concern to the Mining Industry for many years. In earlier times, when mines were small and only high grade ore deposits were mined, the problem was not a great one. But, more recently - during the last 30 to 40 years - the increased world demand for various metals, combined with the vast strides that have been made in the improvement of metallurgical extraction processes, have resulted in the development of lower grade ore bodies.About 30 years ago The International Nickel Company started experiments to stabilize the surface of the tailings and prevent them from becoming a dust source under certain weather conditions. The use of chemicals to form seals, covering with crushed stone, mulching with straw and some early seedings were some of the stabilizing methods tried. Results were either unsuccessful or impractical economically.In 1954 a series of experiments to establish vegetation on the tailings began. Varying degrees of success were achieved but however unsuccessful a particular scheme turned out, the attempt to find a solution was never written off. As we look back, we realize that the first significant break-through came as the result of three test plots planted in the spring of 1957. Each plot covered an area of approximately one-third of an acre. One plot was successful and persisted until it was covered up by the expansion of the tailings area in 1961.In 1960 a review of all our test plots to that date was carried out to assess the factors which effect the chance of grass being established."

Jan 1, 1969

By E. Ozberk, N. Gibson, W. G. Davenport

"In the 1950s, Canada produced more than ninety-five percent of the non-communist world&apos;s nickel and achieved dominance in terms of production, technology and pricing policies.Over the past thirty years there have been dramatic changes in the nickel industry to the extent that Canadian production is now less than thirty per cent of the total.In this document we have presented statistics relevant to this transformation and reviewed the technology, particularly with regards to energy and environmental considerations.Under the new market conditions nickel producers are likely to face more difficult competition than they have encountered in the past.The economic scene and measured nickel reserves dictate that for the purpose of increasing production, new nickel smelters will not be built in Canada in the foreseeable future. However, in order to reduce sulphur dioxide emissions, Canadian nickel smelters will possibly go through some modifications or rebuilding.IntroductionThis paper presents a review of the Canadian nickel industry in relation to the world nickel industry. Major changes are described which have occurred in the characteristics of the nickel market over the last thirty years. The pre sent status of the nickel market with respect to Forecasting future trends is reviewed and attempts are made to predict what further changes will take place in the next two decades. Comparisons are made of the economics of producing nickel from sulphide ores and oxide ores and the advantages and disadvantages the Canadian nickel producers face.A brief critique of the existing and emerging nickel production technologies in Canada and the world is carried out and attempts are mad e to predict the changes which may take place in the foreseeable future."

Jan 1, 1983

By H. Attia, S. Engin

This paper presents a practical approach for determining the optimal spindle speed and the depth of cut in a milling operation within the ever-increasing economic and technical constrains. Analytical modeling and experimental work has been carried out to predict chatter in such operations. The stability lobes determined from this analysis were then used as a constraint in the optimization of the cutting process. The optimal cutting conditions are determined for two different objectives: maximum metal removal rate and minimum cost per unit. It is demonstrated that this approach can be generalized to impose multi-level constrains, e.g., surface integrity and machining accuracy. The approach presented in this work was examined and validated on three NC milling machines. The productivity improvement, cost reduction, while respecting part quality requirements, is demonstrated.

Jan 1, 2006

By K. Gie Tan, Frank Wright

"Misty Mountain Gold Limited (MGL - TSE VSE, MGLCF - NASDAQ) of Vancouver, owns the Harmony Gold Project located in the Queen Charlotte Islands of British Columbia. The deposit contains a mineable reserve of 2.3 million ounces of gold, at a 1.2 g/t cut-off and an average grade of 2.1 1 g/t Au.Discovered in 1970 and frequently investigated by previous owners, full-scale production has not yet occurred because of the complex metallurgy of the deposit. Recent process studies that were completed in six months at Process Research Associates Ltd. (PRA) of Vancouver resulted in significant improvements to the project viability. The work involved detailed mineral processing studies aimed at achieving a marketable concentrate. An option for bio-oxidation and cyanidation to allow on-site dor6 production was also investigated.The main findings at PRA followed the front-end recovery of finely divided free gold (Au) by gravity concentration. Approximately 20% of Au reported to less than 0.2% of the mass, resulting in a grade exceeding 500g/t Au. The resulting gravity tailing provided a uniform feed for flotation evaluation. The optimization of this step allowed for a reasonable primary grind size of 80% passing (&) 50pm. Efficient slime’s rejection was made possible by flotation at a reduced pulp density, and pre-oxidized sulphides were reactivated with Na,S. The regrinding of the bulk flotation concentrate followed by up to five stages of cleaning resulted in a combined gravity + flotation product of 50g/t Au with 82% recovery in less than 4% of the feed mass.Further studies indicated that the flotation concentrate was amenable also to tank bio-oxidation. At 65% sulphide oxidation the gold recovery improved from less than 70% to 90% by cyanide extraction using CIL (carbon in leach). This compares to less than 45% gold recovery from whole-ore cyanidation in several previous studies. Heap leaching may also be considered for lower grade material. PRA’s methodical approach and consistent results dispelled the uncertainty about predicting the material behavior for the Harmony Property."

Jan 1, 2000

By D. Roy Eccles

A multi-element geochemical response, with contrasts of up to 29 times background, was obtained in soil above the Mountain Lake Diatreme, northwestern Alberta. The overall geochemical signature is indicative of an ultramafic source; geochemical responses contain elevated concentrations of Co, Cr,O, Cu and Ni with the presence of high Ba, Ga, HI, PO,, Rb, Ta, Ti and light rare earth elements suggestive ofa kimberlite or lamproite body. The shape, or morphology, of the enzyme leach-based geochemical signature over the Mountain Lake Diatreme combines moderately strong to strong oxidation halos, or a rabbit's- ear geochemical profile, with a sharply-defined apical geochemical profile. Because some Alberta diatremes discovered to date form positive topographic highs, the resultant geochemical signature may express the soil development profile that forms directly on top of kimberlitic and lamproitic bodies. The enzyme leach technique, which has proven to be a useful tool in base metal, precious metal and petroleum exploration, may have a significant impact on exploration for kimberlite, lamproite and related rocks in Alberta by providing industry with a useful and cost effective tool to probe blind and/or buried anomalies identified by airborne and ground magnetic surveys in areas of glacial overburden.

Jan 1, 2001

By Elhachmi Es-Sadiqi

"For over 40 years, CANMET has focused its research on value-added products and energy efficiency in the metals industry. The Efficient Metal Production Program is currently managed by Dr. Elhachmi Es-Sadiqi, and the Canadian steel industry is its main client — both directly and through international organizations such as the American Iron and Steel Institute (AISI) and the International Lead and Zinc Research Organization. AISI membership includes Canadian steel companies IPSCO, Dofasco, Stelco, Algoma Steel and Sidbec Dosco.Canada’s steel industry makes important contributions to the economy. The industry comprises 14 companies and employs 33 600 people in locations such as Sydney, Nova Scotia; Tracy, Quebec; Selkirk, Manitoba; Saskatoon, Saskatchewan; and Sault Ste. Marie, Ontario. With annual production at about 16 million tonnes, sales in 1995 totalled $11 billion, $3.8 billion of which was exported.Canada’s steel industry supplies the transportation, oil and gas, appliance, packaging and construction industries. It is at the forefront of new technology use and has a substantial support network to provide raw materials, equipment and service. Three main segments of the industry include flat-rolled products (e.g., plate and sheet steels), long products (e.g., concrete reinforcing bar and structural steel), and specialty and alloy steels (e.g., stainless steel and tool steels, in both long and flat products)."

Jan 1, 1998

By G. Harper

The Sustut Copper deposit, 230 miles northwest of Prince George, B.C., was discovered in August of 1971. Subsequent exploration has included 56,417 feet of surface diamond drilling in 139 holes. The deposit occurs in gently dipping volcanic rocks of the Upper Triassic Takla Group, which outcrops as rugged mountains. The general Mesozoic sequence comprises some 20,000 feet of green and red basaltic to andesitic rocks. The Lower Formation is characterized by subaqueous basalt, andesite and augite porphyry flows with interbedded breccias. They were rapidly deposited in tectonic depressions of limited extent and steep gradients. Fades changes are abundant. The Middle Formation consists of volcaniclastic rocks made up of fragments from the underlying formation. Two cycles are discernible, both with basal turbiditic, tuf-faceous sandstone and shale units overlain by massive, volcanic conglomerates exhibiting graded and cross bedding. A broader, shallower-water basin is indicated. The top of the uppermost unit was subaerially deposited. The Upper Formation is a variable sequence of volcanic sedimentary rocks. Detritus was supplied from a wide source area and included multiple reworked fragments of the lower formations and material from other rock groups known in the region. Zeolite fades metamorphism is recognized throughout the entire sequence. Epidote is particularly abundant in the Middle Formation, demonstrating the results of metasomatism. The mineralized zone is approximately concordant with the strata over 100-200 feet of the Middle Formation succession. It lies just below the zone of transition from subaqueous to subaerial deposition in the top unit. Hematite, chalcocite, pyrite, bornite, chalcopyrite and native copper are disseminated throughout all sizes of lithic fragments and matrix. Concentration into the specific zone is believed, to be due to upward leaching of copper during low-grade metamorphic and metasomitic reaction. Precipitation occurred in the zone of hydration characterized by prehnite-pumpellyite below the oxidized subaerial rocks.

Jan 1, 1977

By L. O. Cooper

IN THE operation of most mines, hoisting ropes, made of steel, play a very important part in the conveying of men and material between surface and the underground workings. It is obvious that, in order to maintain a maximum degree of safety, certain restrictions must be placed on the loads that may be carried by hoisting ropes, as well as on other factors that may affect the life of the rope. It is the purpose of this paper to suggest ?a new method of defining the necessary restrictions. The three main stresses in a hoisting rope are the static stress, bending stress, and dynamic stress. Crushing stresses, which are also present, are largely indeterminate and may best be allowed for by proper grooving of drum and sheaves, by adequate inspection of cross-over points, and by limiting the number of layers on the drum. They will, therefore, not be considered in this analysis. In the ?recent Ontario regulations, the limiting conditions for the main stresses are specified separately. The static stress is limited by setting a minimum static safety factor of 5.0 The dynamic stresses are allowed for by specifying a minimum capacity factor of 8.5, which has the effect of increasing the safety factor required at smaller depths in a uniform manner. The bending stresses are limited by calling for a drum-dia./rope-dia. ratio of at least 60 for ropes up to 1 inch in diameter and 80 for ropes greater than 1 inch in diameter. One disadvantage of this method is that the controls are too rigid and do not allow the operator sufficient freedom of action within safe limits.

Jan 1, 1951

By S. McAlister

"Falcon Concentrators Inc. has developed a high capacity centrifuge for the recovery of fine, free gold as well as other metals and minerals which were previously thought to be unrecoverable by gravity means. Development started in the early 1980's and the first commercial operation was commissioned in 1986. Gold applications include scavenging conventional gravity and cyanidation circuit tailings, cleaning gravity concentrates, cleaning flotation concentrates to melting grade, scavenging flotation tailings, and placer mining. Recent development work by Falcon has expanded the applications scope of the centrifugal concentrator to include many minerals amenable to gravity concentration including iron, tin, industrial minerals, and hazardous wastes. This paper discusses this technology including its history, present applications, and future potential. OVERVIEW OF CENTRIFIJGAL CONCENTRATIONUsing centrifugal force to enhance the separation of materials by differential specific gravity has been researched for over a century. Many attempts have been made to concentrate minerals in high gravity fields. Patents were granted on this subject as early as 1891 (see Figure 1). Patenting activity continued into the 1920's and has been relatively quiet since. It is significant that no centrifugal system of gravity concentration has been broadly accepted by the mineral processing community until recently. Much of the world's reserve of mineral deposits which are amenable to conventional gravity concentration technology (coarse-grained) have been mined and therefore there is an increasing demand for technology which can economically recover the fine-grained gravity recoverable minerals in the remaining deposits. In addition, centrifugal concentration can play an increasing role in solving environmental problems by offering an inexpensive method of concentrating hazardous materials such as uranium, plutonium, mercury, lead, and other heavy metals. The overall cost of disposing of these substances safely can be drastically reduced if they are recovered into a concentrated form prior to disposal."

Jan 1, 1992