Search Documents

By M. K. Mishra, U. M. R. Karanam

Relative to slender pillars, larger size pillars exhibit improved strata control. Fly ash, though traditionally treated as a waste product, is emerging as an alternate engineering material. This paper deals with the development of a strong fly ash composite material with additives. The geotechnical properties of this fly ash composite were determined and used to trap model core pillars, which resemble squat pillars. The trapped samples were tested under uni-axial loading in the laboratory and the results showed higher load-bearing capacity of the model core pillars. The reinforced fly ash composites provide lateral confinement and exhibit improved post- failure behaviour of the model cores.

Jan 1, 2008

By L. Beiza, L. Velásquez-Yévenes

Chalcopyrite is by far the most abundant copper sulphide on Earth, but it has proved to be problematic in its processing by leaching, mainly related to its refractory nature, slow kinetic rates of dissolution and the formation of an inhibiting product layer on its surface during leaching. This study is focussed on the electrochemistry of chalcopyrite dissolution in acidic chloride system, which has recently gained attention as a feasible alternative to conventional sulphate media for chalcopyrite leaching. It is well understood that chalcopyrite dissolution from mineral grains depends strongly on the solution redox potential at the mineral surface as well as the composition of the product layer that may form on its surface. The chloride ions in solution support the Cu(II)/Cu(I) couple as the primary oxidant, as they can form complexes with the cuprous ions formed, increasing the dissolution rate. Additionally, these ions increase the potential range where chalcopyrite can be oxidized. The chemical reaction that occurs on the surface of chalcopyrite in chloride solutions in the presence of cupric ions will be characterized and the coulometry of the reaction will be reported to understand what is happening on the surface of chalcopyrite. Electrochemical experiments have been carried out to investigate the behaviour of mixed potential by open circuit potential (OCP) measurement for 30 minutes using sulphuric acid at pH 1 under nitrogen at 25⁰ C. The effect of chloride was analysed at 0, 20, 50 and 100 g/L and cupric ions from 0 to 50 g/L. The potentials obtained were then used to carry out chronoamperometry tests for a period of 30 minutes in absence of cupric ions. The mixed potential did not show a significant difference with an increase in cupric concentrations in the absence of chloride. Increased mixed potentials and current densities were observed at higher chloride and cupric concentrations. Chronoamperometry tests at those potentials were used to construct a voltammogram trace which has the same trend as a normal cyclic voltammogram but with much lower current densities. INTRODUCTION As a result of the depletion of copper oxides, the leaching of copper sulphide minerals has become the focus of many studies. Chalcopyrite, (CuFeS2) which is the most abundant of copper minerals, has proved to be challenging to process via hydrometallurgy, mainly related to its refractory nature, slow kinetic rates of dissolution and the formation of an inhibiting product layer on its surface, during leaching.

Jan 1, 2019

By W. Qin

The nucleation of d hydride in Zircaloy-4 has been studied using electron backscatter diffraction. Hydrides prefer to nucleate at intergranular rather than intragranular sites. (0001) a -Zr//(111) d -ZrHx is the most common crystallographic relationship. The hydride platelets are generally interlinked each other and form a chain-like configuration. Based on thermodynamic model, the formation mechanisms of the hydrides at different sites and the interlinked structure were analyzed. We found that the misorientation of two adjacent grains has a crucial effect on hydride nucleation sites, and the tensile stress near the tips of hydride platelets is a key factor affecting the appearance of interlinked structure.

Aug 1, 2010

By Robert A. Creaser, Iain Mitchell, Robert L. Linnen

Abstract - The Bermuda Zn-Pb showing is hosted by dolomitized Blue Fiord Formation of Devonian age, located east of the Ensorcellement dome on the Grinnell Peninsula of Devon Island. Fluid inclusions in hydrothermal calcite indicate that the mineralization precipitated from low-temperature, highly saline brines. The ?34S compositions of sphalerite, galena, and marcasite range from 16.1‰ to 35.2‰. Consequently, the Bermuda showing is interpreted to be Mississippi Valley-type (MVT) mineralization. The apparent age of mineralization has been determined by the Rb-Sr method from sphalerite separates, and a Late Devonian age of 357 ± 50 Ma (MSWD=65), with an initial 87Sr/86Sr ratio of 0.7083 ± 0.0020 is indicated. This date, within error, is the same as the Polaris deposit. This suggests that the mineralization formed during the Ellesmerian Orogen, although it is also possible that mineralization is associated with extension, related to the opening of the Sverdrup basin. The strontium and sulfur isotopes and fluid inclusion analyses indicate the involvement of a brine that acquired its salinity from interaction with evaporites, lower in the stratigraphic succession. The Polaris mine is the type deposit in the Cornwallis Zn-Pb district and is hosted by the Thumb Mountain Formation. The results of this study are significant because they demonstrate that regional brine movement is more widespread than previously recognized, and that MVT mineralization in the Cornwallis Zn-Pb district is not restricted to the Thumb Mountain Formation.

Jan 1, 2004

By Peter N. Calder

Long range mine planning involves developing a mining sequence that schedules the extraction of the ore and waste materials within a final pit limit. The objective is to define a sequence that best meets the defined strategic objectives. The main steps in the creation of an open pit mine plan are the final pit limit design, the design and sequencing of the mining phases, equipment selection and operating cost estimation. Flexibility is the key strategic element in developing a mine plan. Planning the extraction sequences and rates for the various mining areas is a challenging and demanding activity. It is often necessary to consider numerous alternative strategies and what if scenarios. The number of alternatives that can be studied with limited manpower and time resources is restricted. In order to investigate strategic aspects of mine planning, a system to generate workable mine plans rapidly is required. The concept of Visual Mine Planning is that the engineer can visualize the current plan, easily change a component of the plan, such as the annual cut-off grade schedule or the production rate within a particular Phase, and immediately see the effect on the mineralogical and cash flows. If the desired result is not achieved, a change is made and the effect is again immediately seen. This paper presents results of research in this area conducted at the Pontificia Universidad Católica de Chile. The work includes the examination of cut-off grade strategy, sequencing, blending, stockpiling and shovel-truck fleet requirements using simulation.

May 1, 2003

By Bali. D. D., S. Chattopadhyay

"The planning and construction of prime coking coal beneficiation plants in the nationalized mines in India are reviewed. Flow schemes, construction practice, materials consumption, and costs are detailed.Medium-capacity beneficiation plants with multiple loops are recommended under Indian conditions.IntroductionThe reserve of high-grade and easily washed metallurgical coal in India are quite limited. Prime coking coal constitutes approximately 22% of the total resources and occurs exclusively in the Jharia coalfield in the state of Bihar. Bharat Coking Coal Limited (a subsidiary of Coal India Limited (CIL) the nationalized mining sector of India) owns 80% of the Jharia collieries. The development of Jharia coalfield in the pre-nationalized period before 1971 has been characterized by a large number of small mines with primitive mining methods and low productivity. The production of prime coking coal to meet the demand of the steel industry in India has to increase from the existing level of 11.1 million tonnes to 43.4 million tonnes per annum by 2000 AD, thereby producing 5.61 million tonnes and 22.7 million tonnes of clean coal respectively. An ambitious program has been undertaken for development of bigger mines with an average production of 1 to 3 million tonnes per annum. With the fast dwindling reserves of good quality coking coal, more inferior grade coal seams, having difficult washing characteristics, are now being mined. All the coal from the future mines will have to be beneficiated to make it suitable for consumption of steel plants; the following washeries are being planned for construction by 2000 AD:"

Jan 1, 1986

By John G. Henning

The Hoyle Pond underground mine is located in the Porcupine Gold Camp, 18 km east of downtown Timmins. Since the initiation of production in 1985, the operation has produced in excess of 1.9 million ounces of gold at a grade of 15 grams per tonne. Currently, Hoyle Pond ranks 8th in total ounce production for all past and present producing mines in the camp, with the highest head grade of any of the significant past, or present producing mines in Timmins. Cut and fill, shrinkage, longhole and panel mining methods are employed to excavate the narrow gold bearing structures. Using illustrative examples, this paper provides an overview of factors, such as geologic setting, rock mechanics challenges and mine infrastructure, which influence mine design at Hoyle Pond.

Oct 1, 2004

By Hal. Oliver

MR.]. G. TRAILL: My only excuse for contributing to the discussion on Mr. Hall's interesting paper is that I had the good fortune to be employed at Noranda during those romantic years, 1927 and 1928, when construction was at its height. The mine was in course of being rapidly prepared and brought into production, and the initial difficulties in crushing-plant and smelter were being met and overcome. They were stirring days, and perhaps those members who were with the second Empire Mining and Metallurgical Congress in 1927 sensed the atmosphere of excitement and activity that prevailed. Early History. Noranda must surely possess some of the most remarkable ore-bodies known to mining men, and the story of their development is pure romance. Ed. Horne's faith in the property, and the persistence of Thomson and Chadbourne, were richly rewarded in the end, but only after some very thin times had been experienced. In those early days access to the district was by the Kenojevis river and various portages to Osisko lake, on the shores of which the mine and smelter and the town of Noranda now stand. But all the early work was done on the Chadbourne claims, more than a mile to the west; through the b~sh. I have read a log of the events of that period, and through the whole tale of hard work, discouraging developments, occasional shortages of food, and constant danger from forest fires, can be read the faith and persistence of the men in charge. The Chadbourne ore was of that well-known type which, though just too low-grade to pay (with gold at $20 per ounce), is yet sufficiently encouraging to lead one on in the hope of striking something better. It was only as a last resort that work on the Chadbourne claims was suspended and a diamond drill brought to the gossan-covered hill beside the lake. The diamond-driller told me his version (it may be exaggerated) of how the position and direction of the first hole were decided on. He was told, "You might as well set up your drill here, and drill in, say, that direction". I believe that the first hole went through the richest ore ever found at Noranda. After the drill had gone through about 150 feet of solid sulphide ore running 17 per cent copper and 4 dwt. of gold per ton, it passed into barren rock, but the diamond-driller expressed the opinion (I wonder how he knew)) that the hole would come into ore again before long.

Jan 1, 1937

By R. S. Forgan

The synthesis and study of a systematic series of phenolic oximes have shown that substitution in the 3-position can greatly affect extractive efficacy. Solid state, solution and gas phase analytical techniques, including X-ray crystallography, EPR and IR spectroscopy and collision induced dissociation mass spectrometry have been assessed for their applicability in interpreting the origins of differences in extractant strength. The dominant substituent effect on pH0.5 is the change in ligand pKa, with the more acidic ligands being stronger extractants. The influence of the 3-substituent on the stabilising intracomplex H-bonding of their copper(II) complexes also affects extractant strength. The 3-NO2 substituted ligand shows the lowest pH0.5 value, due to a combination of its low pKa and a stabilising bifurcated H-bond assembly around the copper(II) centre. Appending an aminomethyl group to the 3-position gives a ligand capable of binding a metal and its attendant anion. These metal salt reagents show potential to open up new flowsheets for the processing of high tenor copper feeds.

Jan 1, 2007

By K. C. Sole

In most copper solvent-extraction operations, an important consideration in choice of extractant is the requirement for high selectivity of copper over iron. Ester-modified aldoxime extractants presently offer the best Cu:Fe selectivity. In some plants, however, the process feed liquors contain significant amounts of manganese but little iron. Although manganese is not chemically extracted by oximes, trace amounts are carried over to the electrowinning circuit by physical entrainment. This may result in anodic oxidation of manganese which, in turn, can cause oxidative degradation of the organic phase when returned to the solvent-extraction circuit in the spent electrolyte. Many of these operations prefer to operate with higher levels of iron reporting to the advance electrolyte, as appropriate control of the Fe(II)/Fe(III) couple will ensure that manganese remains in the benign Mn(II) form. A new reagent, LS 4202, designed by Cytec, now offers the possibility of tailoring the iron co-extraction, so that appropriate Cu:Fe selectivity can be achieved in the solvent-extraction operation to maintain an electrolyte Fe:Mn mass ratio of >10:1, while retaining the other benefits offered by ester-modified aldoximes. The results of an integrated solvent extraction-electrowinning pilot-plant trial are presented, in which the performances of the conventional extractants ACORGA® M.5774 and LIX® 984N are compared with LS 4202. The Cu:Fe selectivity is demonstrated, along with results on the transfer of other impurities to the advance electrolyte.

Jan 1, 2007

By M. Bourassa, P. Roy

"This paper describes the automation of Kiena's grinding circuit which comprises an open SAG mill circuit and a closed ball mill circuit with two stages of hydrocyclones. The circuit has been instrumented according to a two level control strategy.The regulatory control strategy is implemented in an industrial controller. This controller does data filtering and calculation (flowrate and solid content) and regulates the pump box levels (2), the water additions: or the pulp percent solids (4) and the fresh ore feed rate.The supervisory control calculates for the industrial controller, the fresh ore feed rate setpoint and the pulp percent solids setpoints in order to optimize the grinding circuit operation. It is made of two modules, one for data filtering and one for control optimization. The filtering program uses modern tools to adjust the measured value and estimate missing data (dynamic material balance, on line estimation of model parameter, etc.). The control program acts as an expert system which combines the benefits of model-based control and rule-based control. A multivariable predictive controller (DMC) is used to maintain the circulating load and the hydrocyclones feed percent solids (which is correlated to particle size) while the rule-based control validates the previous output, detects and avoids the SAG overloads and sump pumps overflows.The system has been operating since MAY 1992 and the benefits obtained are discussed.INTRODUCTIONIn 1990, Les Mines d'Or Kiena decided to go ahead with a project for automating its grinding circuit as proposed by the Centre de recherché minerals (CRM). Its objectives in doing so were to marginally increase production capacity (1 % ) and to create a new challenge for plant staff. The main stages of the project, which involved CRM, Kiena Mines and a consultant, are shown in Table 1. The project was completed in May 1992 with the implementation of a supervisory control system. This text describes the main features of the system with a special focus on its most innovative aspects."

Jan 1, 1993

By L. Wolofsky

"The Candego property is in Boisbuisson and Christie Townships, Quebec, about 13 miles south of Marsoui, a village on the north coast of the Gaspe peninsula, 80 miles east of the railhead at Matane. It was the first producing mine in the peninsula. Production to October 1954, when operations were suspended, totalled 68,497 tons of ore, which yielded concentrates containing 8,706,535 lb. lead, 5,870,272 lb. zinc, 355,526 oz. silver, and about 1,000 oz. gold. The property was acquired by the present company in the summer of 1955.The mine has been developed by seven adits, driven into the west slope of the valley of the Marsoui River. The river here is at an elevation of about 1,600 feet, and is roughly 1,500 feet below the level of the adjacent upland. Adit elevations range from 1,760 to 2,330 feet. Five of them are in one vertical zone, on what was originally believed to be a single vein. Past production has come from Nos. l to 5; the chief present high-grade ore reserves are in No. 7.The author's observations were made in adits Nos. 3 to 6, in several of the old pits, in the surface trenches, and on drill core, at various times between December 1952 and September 1953. Much of the surrounding area has been mapped by Jones (I) and McGerrigle (2) for the Quebec Department of Mines. H. M. Kingsbury served as consulting geologist to the mining company for several years.General GeologyThe Candego veins occur in Lower ( ?) Ordovician sedimentary rocks which form a strip about 15 miles wide along the north coast of the Gaspé peninsula. The series includes limestones, shales, and sandstones, mildly metamorphosed in places. Three miles south of the mine is the north contact of the granitic intrusive, regarded as Lower or Middle Devonian, which underlies the Tabletop Mountains area. This batholith is about 10 miles long, in a north-south direction, and about 4 miles wide. At Mount Albert, about 5 miles west of the Tabletop intrusion, is a group of basic rocks, amphibolites and serpentinized peridotites, thought to have been intruded at the close of the Ordovician."

Jan 1, 1949

By H. Wyslouzil

"The Kelsey Centrifugal Jig is a gravity separation device which utilizes the principles of the conventional mineral jigs but with the additional feature of being able to vary the apparent gravitational field. This is accomplished by utilizing the specific induced movements of the conventional jig within a centrifuge.Pilot plant trials have been underway since July 1988 to evaluate the potential applicability of this technology to various process streams at Rio Kemptville Tin.The grade/recovery relationships for samples treated in the jig were consistently better than results obtained from tables. Recoveries of more than 90% were attained at concentrating factors ranging up to 20. When compared with electrostatic separators, the jig achieved equivalent metallurgical results in a two stage process, without the expensive requirement of filtration and drying. Recoveries exceeding 96% were achieved with final concentrate grades averaging higher than 60% tin.INTRODUCTIONMineral jigs have been used for hundreds of years. Many different types have been developed, and each one has numerous variations. In recent years, the idea of applying centrifugal forces to conventional jigs has been put to practical tests and today a number of units are in commercial production. In principle, by enhancing the apparent gravitational field, it should be possible to recover finer particles by overcoming viscosity and surface effects which tend to limit existing gravity devices. In addition, it may be possible to use gravity to separate minerals with much smaller specific gravity differences."

Jan 1, 1990

By Stewart A. Ferguson

Location.-The property consists of eight claims (P-12339 to 12343, 12403 to 12405) in Robb township, adjoining Jamieson township on the west. A mocor road extends twenty-two miles northwest from Timmins to the mine. Acknowledgments.- The field work was done in 1940 and 1943, while the writer was employed by the Ontario Department of Mines. The Metals Reserve Company has made available information regarding the property through Messrs. W. R, Dunbar, of Hollinger Consolidated Gold Mines, and W. C. Ringsleben, of the Metals Control Board, Department of Munitions and Supply.

Jan 1, 1945

By Dara L. Hrytzak-Lieffers

Canada has long since been a place that has led the world in mining development, in a safe, clean, and sustainable manner. This has led to the integration of corporate social responsibility (CSR) philosophy in corporate governance, policy, and programming. The paper will identify the basis of CSR practise in Canada?s mining industry and provide a Canadian example of CSR implementation. Biography Dara Hrytzak-Lieffers is the manager, corporate social responsibility at Cameco Corporation. She oversees corporate CSR initiatives including the Sustainable Development report and public engagement programs. Dara received her BA in International Studies from the University of Saskatchewan and an MA in International Conflict Analysis from the Brussels School of International Studies. She is a recent graduate of the World Nuclear University summer institute.

May 1, 2011

By R. Carrier

"There has been a continuous evolution with the use of pre-cast concrete elements in the construction of aluminum smelters. In 1990, Phase I of Alouette was built using cast-in-place concrete exclusively. Whereas, other AP 30 technology plants such as Hillside 2 in the mid-1990s used pre-cast concrete beams with cast-in-place floors. Mozal 2, in 2002, used pre-cast concrete beams with pre-cast partial-slab operating floors. Alouette Phase II went further. Not only were the potroom building beams and floors pre-cast, but the entire pot support system, insulating walls and basement jersey walls were pre-cast. Once the techniques for bending and welding the reinforcement bars and the design for attaching electrical insulating plates to the concrete was perfected, the challenge for the project remained only in the logistics of transporting the pieces to site and simple erection. The overall impact on the project was dramatic. Using prefabricated concrete not only allowed advancement of the schedule, but totally eliminated formwork, re-bar installation, and form removal activities along with the handling of all the materials involved with these activities. With the elimination of these labour and material-intensive portions of the job, exposure to work injuries was dramatically reduced. The most prevalent activity for lost time accidents is during the rough work associated with concrete formwork, placing concrete and form removal. Another area where prefabricated elements were successfully used on Alouette Phase II was for the insulating walls enclosing the pot area, known as the ""claustra walls"". Usually these walls are constructed in-situ using mortar and breeze block. Success was also achieved with prefabrication of the perimetric walls that are installed at the lower floor of the potroom. A big advantage of using prefabricated concrete in the electrolysis area is in assuring electrical isolation for the operating floors. Poured concrete requires a meticulous clean-up effort before commissioning to establish the electrically ""floating"" characteristics of the operating floors. Poured concrete results in ""wash"", stray wood,"

Jan 1, 2006

By Robert D. Brown

"On April 22, 1980, the Ontario government introduced a totally new incentive program for mineral exploration in the province to be effective September I, 1980. Replacing the former Mineral Exploration Assistance Program (MEAP) and also the assistance formerly provided to the mining sector under the Small Business Development Corporations Act, the new Ontario Mineral Exploration Program (OMEP) promises to offer a valuable benefit to certain eligible applicants.Unfortunately, the program is not without its shortcomings: the eligibility for grants or tax credits under the program is comparatively restrictive, and an October 1980 federal budget provision to amend income tax legislation would blunt some of the originally intended attractiveness of the grants and credits.IntroductionIn his budget of April 22, 1980, Ontario Treasurer Frank Miller introduced a new incentive program to encourage mineral exploration in the province.The Ontario Mineral Exploration Program (OMEP) replaces the Mineral Exploration Assistance Program (MEAP), which will be phased out by March 31, 1981. Exploration programs approved under MEAP will continue to qualify for incentives under that program, but will not qualify for OMEP."

Jan 1, 1981

By D. Y. Li, C. D. Ma, T. Zhou, T. J. Cheng

In this paper, a number of experimental tests are carried out to study the strength difference on rectangular prismatic marble specimens with different height-to-width (H/W) rations. The specimens have a nominal size of 45×15 mm in the compressive cross-section (W×T) and different heights (H = 22.5 mm, 45 mm, 60 mm and 90 mm). It is to say that the height-to-width ratios are equal to 0.5, 1.0, 1.33 and 2.0, respectively. The quasi-static uniaxial compressive tests are finished by a servo-controlled INSTRON machine (the strain rate at about 10-5/s), and the dynamic compressive tests are finished by a diameter of 50 mm cylindrical SHPB apparatus (the strain rate reaching about 101/s). The rock failure process of marble specimens is captured by a high speed camera in order to distinguish the fracture propagation behaviour. It is found that the compressive strengths increase when the H/W ratio of marble specimen changes from 2.0 to 1.0 due to the end clamping effect both for quasi-static and dynamic loads. However, when the H/W ratio changes from 1.0 to 0.5, the apparent compressive strengths decrease both for the two loading conditions. The strength decrease of short marble specimens may be attributed to the change of failure mode from shear to slabbing, which can be identified by the fracture patterns of the specimens. Based on the uniaxial compressive tests, the slabbing strength of the marble was found to be about 40% of its UCS for the specimens with a nominal height-to-width ratio of 2.0. In addition, it is found that the dynamic increase factors (DIF) are affected by the specimen’s aspect ratios. It implies that the same aspect ratios should be used to compare the dynamic and static compressive strength of rocks. Meanwhile, both the static and dynamic tensile strengths of the marble are obtained by the Brazilian disc tests. The ratio of the dynamic tensile strength to the static tensile strength of the marble is about 2.68.

Jan 1, 2015

By F. E. P. PEARSON

Sandstone quarried from an island in Lake Winnipeg is barged 130 km to a processing plant at Selkirk on the Red River. The stone is white, poorly consolidated, and consists of rounded quartz grains of high natural purity. It is an important supplier of silica in Western Canada for glass, fiberglass, foundry and other industrial uses.

Jan 1, 1984

By U. Martin

Advanced copper materials for conducting applications require an optimal combination of high mechanical strength at ambient and moderately elevated temperatures together with superior electrical and thermal conductivity. Mechanical alloying under repeated cooling of the milling vials in liquid nitrogen has been applied to produce ultra-fine grained (UFG) oxide dispersion strengthened (ODS) copper with a high yield strength at ambient temperature. In the present study ODS copper was manufactured by mechanical alloying of copper powder and 3% by volume of incoherent oxide dispersoids. During the high-energy milling a homogeneous distribution of fine dispersoid particles (diameter nearly 100 nm) can be achieved in the powder. Samples with a density of more then 97% of theoretical value were produced by uniaxial hot pressing under 650 MPa at 600°C for 20 minutes. The high yield strength at ambient temperature can be described by a linear superposition of the Orowan stress for particle hardening and of ultra-fine grain strengthening according to the Hall-Petch mechanism. Simultaneously, a best value of 75% IACS could be obtained for the electrical conductivity. The creep behaviour of ODS copper in the temperature range from 500°C to 700°C is described within the frame of diffusional creep deformation.

Jan 1, 2007