Search Documents

By A. Himsley, E. Byleveld

"With reference to the chemical constraints underlying the ion exchange process for uranium recovery, a generalized view is presented on the actual and the achievable efficiency of the process. The area considered is restricted to acid leach circuits in combination with nitrate, chloride or sulphuric acid elution.A comparison between actual plant results and the chemical requirements shows that:(a) Unless new and better ion exchange resins are developed, no dramatic change in equipment size and resin inventory is""anticipated. (b) Elution efficiency, especially for sulphuric acid, may be improved considerably. More concentrated eluates may beproduced at lower chemical consumption. A possibility of achieving additional purification solely by ion exchange is discussed.IntroductionThis paper presents a generalized view of the actual and the achievable efficiency of the ion exchange processes for urannium recovery. The study is restricted to acid leach circuits in combination with nitrate, chloride or sulphuric acid elution. The ultimate efficiency attainable with ion exchange is dietacted by the chemical reactions underlying the process. The most sophisticated technology cannot change the diffusion rates in the ion exchange resin nor make the uranium loading exceed its equilibrium valueThe design of an ion exchange plant for uranium recovery involves a considerable number of parameters as a result of the wide variety of pregnant solutions produced from different orebodies. Therefore, a generalized approach of the ion exchange process inevitably neglects some parameters which maylead to significant variations in apparently identical situations.The uranium concentration in the pregnant solution, together with its pH, are the principal variables which determine resin loading and residence rime in the ion exchange system. On the elution side, the type of eluant and its concentration will determine the contact time required and the amount of eluant needed to strip the resin. The temperature, the properties of the ion exchange resin, the total dissolved solids in the feed solution and the competing ions are other variables that affect the chemical performance; these, however, may be considered as a correction of the principal parameters if one is interested only in general trends."

Jan 1, 1980

By F. M. Makarinsky

"This paper describes the conversion of conventional froth flotation cells to open-trough type bank cells, with 'buried' vertical metal partitions. These changes have resulted in: total froth removal along the full length of each bank of cells; extended flotation cell retention times; and has extended the life of the metal components, particularly towards the upper flotation cell areas.INTRODUCTIONOver the past twenty years, the flotation cells used at Falconbridge Limited, Sudbury operations concentrators, have gone through major physical changes. The various concentrators generally started with 100 cubic foot Denver Sub 'A' flotation cells. From these units, we progressed to 'converted' DR units, and/or Denver DR units, if purchased new. (Figures 1, 2, 3)In 1980, the Strathcona concentrator started to pay more attention to the 'front end' rougher flotation cells. Initially, the converted DR flotation cells had 'cut-outs' removed (Figure 4) at all upper vertical cell partitions, towards the ff9th lip areas, in order to get additional froth removal."

Jan 1, 1985

By D. W. Bennett, J. B. Hadaway

The operation at Phu Kham commenced design and construction in early 2006 and was commissioned in May 2008. This paper will examine and discuss the project from the inception of flow sheet development and equipment selection, equipment design and manufacture, construction, commissioning and ramp up to full production. The paper will touch on the strategies employed to achieve a short schedule and the efficient use of capital, but with the main emphasis on the grinding circuit. Various challenges during the early years of operation will be discussed including the effect of ore characteristics, including competency, on the performance of the grinding circuit. Actions to overcome these challenges and to enhance performance will also be discussed. Finally, current and future plans to improve the performance of the grinding circuit and the overall plant will be summarised.

Jan 1, 2012

By J. E. Danoczi

Shore Gold Inc. (Shore) is presently designing a diamond processing plant for the Star and the Orion South kimberlite deposits in the Fort à la Corne area kimberlite field in central Saskatchewan. The first step in the plant is diamond liberation and occurs in the comminution section. Diamond liberation is the process of breaking up the kimberlite rock, as ?gently? as possible since essential to the diamond liberation process is the minimization of diamond damage, particularly for the larger, high value diamonds. The Southern African diamond mines traditionally use Jaw and Gyratory crushers as their primary comminution method. However, these diamond mines generally process the harder, competent kimberlite that is located in the diatreme zone as well as the root zone of the volcanic pipe. Softer kimberlite is typically located in and around the crater area of a volcanic pipe and it is this source of kimberlite that makes up the majority of kimberlite for both the Star and Orion South deposits. These softer kimberlites can be readily broken up using abrasion and attrition imparted by AG mills, this being the preferred method of comminution for minimizing diamond damage.

Nov 1, 2011

By Don Peel, Jeremy Richards

Abstract - Aggregates (sand, gravel, and crushed stone) are low unit-cost products extracted in very large volumes for the construction of buildings, roads, and other infrastructure essential to modern society. Because of their low unit value, transportation costs are a key factor in resource economics, and deposits are commonly developed close to market (i.e., close to towns and cities, or along low-cost transportation corridors). This proximity results in potential conflict with residents over land use, disturbance, and pollution. Management of aggregate resources in Alberta is examined in the light of resource geology and distribution, and governance. A case history of development of the Calahoo-Villeneuve deposit is described, and the conflicts between residents and developers that led to establishment of an Area Structure Plan (ASP) are explored. The plan sets limits to, but at the same time safeguards, resource extraction, and defines terms for compensation to residents through a voluntary levy on production (Community Enhancement Fund). This fund is used to support community activities and to pay for a groundwater monitoring program. The ASP is examined within the context of the "Seven Questions to Sustainability" as set out by Mining,Minerals and Sustainable Development-North America (2002). It is concluded that the ASP, for the most part, provides a good model for conflict resolution and sustainable resource development, which could usefully be applied in other jurisdictions. The ASP was developed at a municipal level, and adoption at a provincial level would aid sustainable development of aggregate resources across the province.

Jan 1, 2003

By Douglas C. Fraser

"Geophysical data are often presented on maps, sections or profiles with minimal data processing. A common example is magnetic data, in which the diurnal-free raw readings are merely contoured on a map. Other examples include profile presentation of VLF-EM data, IP pseudo-sections and airborne EM anomalies which may be shown on a map with only the measured amplitudes indicated.In recent years, efforts have been directed to the portraying of data in more useful forms. A number of algorithms (i.e., manipulative procedures and equations) have proven to contribute significantly to the usefulness of geophysical data. Some can be applied manually; others are sufficiently complicated to require a computer. Some merely alter the data to a more useful geometric form without altering the units. Others yield quantitative estimates of source body parameters such as conductivity and shape. Several examples follow:1. A simple algorithm is in common use which transforms noisy non-contourable VLF-EM data into less noisy contourable data. The input is the dip angle in degrees or per cent and the output is also in these same units.2. A simple algorithm has recently been developed which allows multi-level dipole-dipole IP data to be contoured on a map. Again, the units are not altered.3. A relatively complicated algorithm is in common use which transforms non-contourable height-sensitive helicopter EM data into contourable resistivity data,4. An algorithm has been recently developed which transforms non-contourable height-sensitive EM data into contourable weight per cent magnetite.The purpose of all the above techniques is to present the data in a simplified form. This, in turn, allows an easier assimilation by the user of much of the information content of the data."

Jan 1, 1981

By H. W. Hughes

"The Wasamac Gold Mines mill, situated 10 miles from Rouyn-Noranda on highway 59, commenced milling April 1st 1965 at a rate of 700 tons per day. This has gradually increased to over 1200 tons per day in December. The mill has done up to 1400 tons on occasion.The ore was formed in the Wasa shear zone by means of replacement. The minerals which replaced the original rocks were carbonates, quartz, pyrite, chlorite, gold and silver. Work index varies from 9. 6 on the chlorite to 11. 6 on the quartz. The gold is very finely disseminated throughout the gangue and while associated with the pyrite is not included in the pyrite. Very seldom is gold found or seen in the free state.Test work showed a medium fine grind of 85 to 90 per cent was necessary to achieve a 95.00 per cent extraction. Straight cyanidation time of 30 to 36 hours was indicated. This has been borne out by subsequent mill performance with a grind around 87 per cent minus 200 mesh and extraction ranging from 95 to 96 per cent.When it was decided to bring the Wasamac property into production, the Bicroft Uranium Mines Ltd. crushing and grinding units together with one pebble mill and the pachuca tanks from Dyno Uranium Mines Ltd. were purchased.Wasamac crusher house and mill buildings are of laminated wood construction, covered with 5/ 8th inch plywood and corrugated iron sheeting."

Jan 1, 1966

"There are a number of disciplines in the minerals industry for which concern has been expressed regarding the sustainability of human capital. The boom-bust cycles that occur in the industry, the trend in tertiary education towards consolidation or in some cases cessation of minerals related programs and the increasing frequency of fly-in fly-out operations can all contribute towards a decline in the number of professionals with basic skills in process mineralogy. This paper describes approaches taken by the authors to incorporate process mineralogy into three levels of education, namely undergraduate, recent graduate and experienced professionals. The primary objective in designing the learning activities is the development of authentic learning experiences that provide participants with relevant skills in process mineralogy. Selected examples of approaches used by other education groups globally to address this issue are also provided.INTRODUCTIONThe boom and bust cycle of the mining industry has trickle down effects in tertiary education in terms of the ability of universities to consistently provide high quality graduates with relevant skills. When the commodity price surged in 2002 skills shortages in critical resource related professions were reported and despite investment in skill development there was a view from employers that not enough young people were graduating from relevant education programs (PricewaterhouseCoopers, 2012). At the time this signalled positive growth for engineering disciplines catering to the mining industry, however during the downturn cycles, most recently since 2012, graduates exiting from the discipline can find employment difficult and this contributes to reduced enrolments in subsequent years. From an AusIMM (Australasian Institute of Mining and Metallurgy) members’ employment survey conducted in 2013, more than half of the graduates exiting from disciplines related to mining and minerals were not confident of finding employment (AusIMM, 2013). In the long term the concern is not only how to sustain enrolment and graduate numbers but also to provide the opportunity for students to acquire the professional skills that they require to make them attractive to industry.Maintaining and sustaining core competencies in the minerals discipline is an ongoing challenge. There have been a number of recent papers on this issue presented at international conferences (e.g. McCaffrey et al, 2014; Drinkwater and Napier-Munn, 2014) and there is general agreement that one of the ways in which the deficit in foundation concepts can be addressed is through workplace development. Drinkwater and Napier-Munn (2014) presented data from a survey of industry professionals that indicated that more than 90% of respondents undertook on average 30 days of training each year of which approximately 5 days was professional short courses."

Jan 1, 2016

By A. Himsley

"There is an ever-increasing demand these days for efficient methods of removing metals from solutions especially for selectively recovering a particular metal from a mixture of metals in solution.Up until the mid l 930's the only methods widely practiced for such separations involved precipitation techniques or electrolysis. Both these methods have limitations and indeed can only be used for certain metals.It is only within the last 40 years or so when synthetic ion exchange materials became available that chemists in industry and universities have been able to apply ion exchange techniques to a wide variety of separations that not only would be impossible by precipitation methods but which are now achieved with much greater efficiency.Ion Exchange TechniquesIon exchange is a unit process that can be applied using either liquid ion exchangers or solid resin particles. Liquid ion exchange - or solvent extraction as it is often referred to - is used in a number of special areas dictated mainly by the nature of the separation.On the other hand, ion exchange resins are much more widely used and consequently a great deal more is known about their application to a variety of metal separations.In both systems there is a loss of the ion exchange material which in the case of solvent extraction results in hydrocarbons going to waste. The ion exchange resin systems lose resin in the form of small particles, referred to as ""resin fines"", and these are insoluble.The loss of liquid ion exchanger is due to the fact that it is slightly soluble in water and consequently the loss is a function of the volume of liquid with which it comes into contact and is not related to the amount of metal processed."

Jan 1, 1975

By Ken G. Stowe, Stephen L. Chryssoulis, Joe Y. Kim

"Lead ions originating from galena during processing of complex sulphide ores migrate to ""cover"" the surface of sphalerite and iron sulphide mineral rarticles, and cause poor selectivity in differential flotation. Generally in sulphide ore processing, the lead activated minerals float in the Cu/Pb circuit. Subsequently, surface lead complicates the zinc flotation circuit by lowering the concentrate grade due to the co-flotation of lead- activated iron sulphide minerals. The effect of lead in the differential flotation of sphalerite from Cu-Pb-Zn and Pb-Zn ores is discussed. Plant and laboratory test data are interpreted by determining the surface composition of individual grains of sphalerite and iron sulphide rarticles using two surface analytical techniques, Laser Ionization Mass Spectrometer (LIMS) and Time of Flight-Secondary Ion Mass Spectrometer (TOF-SIMS). Cationic and anionic species on the surface were analyzed to elucidate the phenomena.IntroductionSurface properties play a critical role in many aspects of mineral processing such as flotation, flocculation, etc. An understanding of interaction mechanisms of different reagents (inorganic cations and anions, collectors, regulators, etc.) with mineral surface in an aqueous solution is a very important pre-requisite in achieving the desired selective flotation. In the flotation of complex sulphide ores, the flotation collectors respond to the activation of minerals such as sphalerite, pyrite etc. by heavy metal ions of Cu, Pb or Ag, which is a strictly surface phenomenon."

Jan 1, 1995

By Brien A. Perry, Art Wiebert

"Many organizations which have implemented Total Quality Management (TQM) are finding that the process has either stalled or is not working so well as originally envisioned. This can be particularly evident in an engineering environment where the uniqueness of engineers and their particular culture has not been adequately considered. Winning the commitment of a highly educated group ojprojemnnJJ1s to the TQM concepts, which are often initially 5W2 as too simplistic poses special challenges.Successful TQM implementations are found among technical groups where employees have significant input into creating the new work culture, feel empowered to make changes and are well trained in teamwork. A coach who is knowledgeable in implementation problems can, when working closely with the technical teams, help them circumvent obstacles and guide them successfully through the difficult early phases. The remaining key ingredient for success is supportive management which leads the change and is both informed and appreciative of the accomplishment being made.This Paper is based on first-hand experience with common problems and results encountered in implementing TQM in an engineering environment. Described in the paper are ways of avoiding these problems through awareness of the unique nature of engineering groups, implementation planning, just-in-time training and coaching people in the TQM process. The paper concludes with a focus on the opportunities and results from a successful implementation. These opportunities and results include the benefits each engineer can realize through process thinking, empowerment and teamwork."

Jan 1, 1995

By Shahram Tafazoli

ABSTRACT: This article presents a novel technology for sensing the size of rocks after blasting in hard rock mines. Blast engineers require rock size statistics to carefully adjust the blasting parameters. The rock fragmentation requirements vary depending on the ore type and crusher specifications. The most popular statistical parameters in the industry are the so-called P numbers (e.g., P80 and P100). A machine vision based system is introduced here for automatic image collection and fragmentation analysis of the material right inside the bucket or dipper of mining shovels. A heavy-duty camera provides the required imaging data to an embedded computer mounted inside the cab. A custom machine vision software continuously analyzes the captured bucket images and stores the suitable ones in local storage which are then fed to a Desktop software for automatic fragmentation analysis. This technology has been developed by Motion Metrics International and is commercially available as FragMetrics?.

Oct 1, 2009

By Shahram Tafazoli

This article presents a novel technology for sensing the size of rocks after blasting in hard rock mines. Blast engineers require rock size statistics to carefully adjust the blasting parameters. The rock fragmentation requirements vary depending on the ore type and crusher specifications. The most popular statistical parameters in the industry are the so-called P numbers (e.g., P80 and P100). A machine vision based system is introduced here for automatic image collection and fragmentation analysis of the material right inside the bucket or dipper of mining shovels. A heavy-duty camera provides the required imaging data to an embedded computer mounted inside the cab. A custom machine vision software continuously analyzes the captured bucket images and stores the suitable ones in local storage which are then fed to a Desktop software for automatic fragmentation analysis. This technology has been developed by Motion Metrics International and is commercially available as FragMetrics?.

Oct 1, 2009

By Shahram Tafazoli

This article presents a novel technology for sensing the size of rocks after blasting in hard rock mines. Blast engineers require rock size statistics to carefully adjust the blasting parameters. The rock fragmentation requirements vary depending on the ore type and crusher specifications. The most popular statistical parameters in the industry are the so-called P numbers (e.g., P80 and P100). A machine vision based system is introduced here for automatic image collection and fragmentation analysis of the material right inside the bucket or dipper of mining shovels. A heavy-duty camera provides the required imaging data to an embedded computer mounted inside the cab. A custom machine vision software continuously analyzes the captured bucket images and stores the suitable ones in local storage which are then fed to a Desktop software for automatic fragmentation analysis. This technology has been developed by Motion Metrics International and is commercially available as FragMetrics?.

Oct 1, 2009

By Bill Dupley

We believe that the inability of employees to effectively manage information has reached an epidemic problem throughout the corporate world. ? All the available knowledge in the world is accelerating at a phenomenal rate. ? The whole world's codified knowledge base (all historical information in library books and electronic files) doubled every 30 years in the early 20th century. ? By the 1970s, the world's knowledge base doubled every seven years. ? Information researchers predict that by the year 2010, all the world's codified knowledge will double every 11 hours.

May 1, 2003

By Dean McDonald

The Committee Bay Greenstone Belt extends over 300km and is one of the largest unexplored greenstone belts in North America with excellent gold and diamond potential. Committee Bay Resources Limited holds over 550,000 acres of land with prospective geology in the Committee Bay area southwest of Melville Peninsula, Nunavut. Committee Bay is a typical Archean greenstone belt comparable to the Yellowknife, Red Lake, Kirkland Lake and other prolific gold belts. Drilling during 2003 at Committee Bay resulted in: 1) the discovery of high-grade gold-bearing quartz veins with silicification and sulphidation at Three Bluffs, and 2) the continuation of high-grade gold mineralization in the hinge area of the iron formation at Inuk. Gold mineralization at Three Bluffs is identified in iron formation and adjacent sediments and has been traced by drilling for over 700m. The Three Bluffs iron formation is open to depth and along strike where is has been traced on surface for over 6km. In January 2004 Committee Bay and joint venture partner Gold Field?s announced a $7.1 million exploration program for the Committee Bay project in 2004. A total of 8,000m in exploration drilling has been approved for the expansion of the Three Bluffs to the resource stage and drilling of at least five new target areas. Additional mapping, sampling and geophysics will be used to identify new gold targets along the very prospective Committee Bay belt.

May 1, 2004

By W. R. Hargrave

"Mining OperationsOre will be mined by open pit techniques. Because of the high grade of the deposit and the low strip ratio, mining rates are small relative to most other open pit operations.The ore deposit is located in the valley of the main fork of Red Dog Creek. The bulk of the deposit is located on the southwestern flank of the creek, but mineralization does traverse the creek in both the north and east directions.Erosion has exposed the orebody in a number of locations, and has resulted in oxidation of the mineralization closer to the surface. Although much of this oxide material is very high grade, it leaches readily and, at least in the initial phases of the operation, will be stockpiled and not treated in the concentrator.During construction, 2.3 million mt. (2.5 million st.) of overburden and waste will be stripped from the orebody to expose ore for initial operations. Competent non-mineralized waste will be used to build roads and waste dumps, but the bulk of material removed consists of oxide or ice-rich soils and weathered rock which is not suitable for construction.The annual ore mining rate will be 1.9 million mt. (21. million st.). The strip ratio will start off at 1.2 to 1, falling to 1.0 to 1 by year 5 and ultimately to 0.8 to 1.Bench heights are set at 7.6 m (25 ft). Pit slopes will vary depending on the material present in the wall. The slope, through competent waste and the sulphide package, was set at 45 degrees. This is flattened to 26 degrees (i.e. 2: 1) through overburden and Upper Kivalina shales. The Kivalina Shales are an ice-rich shale whose carbonate matrix has been leached out and which exhibits little or no strength as it thaws. In addition, a 100 ft containment berm will be left in the wall below overburden and Kivalina."

Jan 1, 1989

By M. L. Haider

Introduction I Appreciate very much the opportunity of discussing with you tonight oil developments in western Canada. These developments are of importance to all of us, first because of their great economic significance to all of Canada, and second because of the location of the new oilfields. Situated as they are in the west and northwest, they are of considerable strategic value from the standpoint of continental defence. The story of oil development in Canada covers a span of almost a century, during which time success in finding reserves of petroleum was barely sufficient to maintain interest in continuing the search. Finally, in 1947, a well of the first importance was completed in Alberta and, judging by discoveries made since then, it appears that Canada, at long last, is to become an important producer of petroleum.

Jan 1, 1950

By Susan W. Campbell, Bruce Regensburg

"The CIM Careers Task Force has addressed industry's concern of a perceived shortage of skilled personnel over the coming decade. The industry is faced with a fundamental shift by young Canadians away from scientific and engineering careers, coupled with the fact that today 's students know little about the minerals industry and have a poor image of it.The responses to two questionnaires which were distributed to CIM members, government, professional associations, and educational institutions, formed the backbone of the Task Force position paper, which presents a shopping list of ideas and initiatives for consideration and to facilitation by the various organizations concerned.Tackling the image of the minerals industry is part of the answer to the careers crisis. On the positive side, the minerals industry provides the allure of a treasure hunt for young people and is seen as a significant contributor to the economy. It is understood to be well paying, provide good opportunities for advancement, individualism, and travel, and to be rich in esprit de corps. Enhancement of these positive aspects of the image can take place at all student age levels.Numerous initiatives tackle the negative aspects of the image. Young people perceive the industry to be environmentally damaging, which is the most crucial aspect that needs to be addressed. The industry is seen as still in the pick-and-shovel days and as a sunset industry that is running out of ore. Work in the minerals industry is perceived as dangerous and lacking glamour. And finally, the perceived remoteness of operations and exploration is seen as a drawback to a largely urbanized student group.Tackling young peoples' curiosity and interest in the minerals industry throughout grade school and encouraging postsecondary science and engineering students to enter the minerals industry by ensuring summer employment is the second part of the equation.The CIM Careers Task Force position paper develops strategy to attract and maintain interest of students in grade school, junior high, senior high school, and in post-secondary levels. The strategy outlines initiatives targetted at each of the educational levels and action plans to accomplish the objectives."

Jan 1, 1993

By J. F. Archibald

This paper reviews the formation of the Canadian Mining Education Council (CMEC) and its terms of reference. CMEC considers that Canada?s mining schools represent a distinct competitive advantage to the Canadian Mining Industry. The core objective of CMEC is to reinforce the links between the constituent schools and their individual Industry Advisory Committees. The latter traditionally provide the schools with a great deal of guidance on a range of planning issues, including recruitment, curriculum, research and infrastructure. Beyond those bounds CMEC intends to improve its ability to network with the industry and government. It is concerned overall with the objective to raise the quality and level of its educational and research contributions to meet the needs of industry and society.

May 1, 2002