Search Documents

By Jochen Petersen, Alison Lewis, Cledwyn Mangunda

Run-off and waste water streams high in dissolved metal content are generated in all mining operations. The metals pose a threat to life due to their persistent bio-accumulative toxic (PBT) characteristics. Hence, there is a need to treat mine waste water effectively. Lime precipitation is the technology of choice through which Fe, as the major metal species, is removed as Fe (III) oxyhydroxides with other metals co-precipitated and/or adsorbed. Sulphates are removed as gypsum or incorporated into the Fe phases. The resulting sludge has poor dewatering characteristics and is deposited in landfills, with an inherent risk of returning the Fe back into the water cycle through leaching. This study seeks to understand the mechanisms behind the formation of this sludge in terms of product quality. The relationship between process conditions and product characteristics has been investigated through exploring the effect of Fe (III) concentration on the precipitate product characteristics (particle size distribution (PSD), size, morphology and structure) and quality (in terms of filterability, settling ability, etc.) in a simplified system. Neutralisation of acidic synthetic aqueous Fe (III) sulphate streams containing 50, 400 and 800 mg/L Fe(III), respectively, was effected by mixing it in a continuous stirred tank reactor (CSTR) with dissolved calcium hydroxide for pH control at a residence time of 15 minutes. Precipitate samples analysed for morphology and PSD, using nanoSEM and Zetasizer respectively, showed a general decrease in PSD and zeta potential with increases in feed Fe (III) concentration. These results were used to infer the particle size enlargement mechanisms of Fe (III) oxyhydroxide precipitates under a given set of operating conditions. Preliminary product quality results indicate that a high concentration (800 mg/L) leads to the rapid formation of metastable precursors with poor product quality, whilst a low concentration (50 mg/L) leads to formation of thermodynamically more stable precipitates with good product quality. The approach demonstrates a potential route forward in terms of linking operating conditions to the attainment of desirable characteristics rather than specific precipitate phases which are difficult to identify.

Jan 1, 2016

By Robert B. Parsons

"First down and four to go. In the game Of football, this is not a bad position to be in. However, in this game of political football, it means that there is still a long way to go. The government in Ottawa has concluded an important agreement with one producing province, and now has at least four more provinces to deal with-B. c., Saskatchewan, Nova Scotia and Newfoundland.On September 1, 1981, the federal and Alberta governments took a significant step forward in formulating an oil and gas policy for Alberta and the rest of Canada on signing a comprehensive five-year agreement that covers taxes, prices, incentives and other fiscal matters related to the production and marketing of oil and gas.This month, Tax Notes examines the main features of the agreement, and offers some eye-opening observations of what the new accord could mean for the future of the Canadian petroleum sector in particular and Canadian business in general."

Jan 1, 1981

By Jie Zhu

Coal bumps are a special form of release of geologic strain energy that has already been one of the most dangerous hazards to underground mining safety in China. A number of coal-bump models have been developed to quantify coal failure under assumption that a bump is a kind of non-gas induced outburst. However, some technical experts in charge of micro-seismic and gas monitoring have found unusual gas emissions before and after bump, which suggests that it is possible for gas to trigger coal bumps. Considering the coal reservoir as geological body composed of the coal matrix and gas, a new model based on Lippmann?s bump model is proposed to understand the initiation of coal bumps. The redistribution zone from excavation of a roadway has been calculated and analyzed regarding its relation with mining depth. It is shown that high gas pressure may push the coal seam to overstep the critical state due to extension of the plastic disturbed zone, and this is harmful to the stability of coal seam. This model successfully explains the bump phenomena of the Xinzhouyao mine at shallow depth.

Aug 1, 2013

By N. Shi, T. G. Joseph

ABSTRACT A revised equilibrium approach to evaluate dipper-ground interactions during the dig cycle of ultra-class mining shovels operating in soft unblasted uniform ground conditions is presented. A review of previous approaches, leading to an outline of the modifications and ground condition considerations, is made in support of the reasoning and basis for the derivation presented. An analytical solution is provided to the scenario of a cable shovel dipper digging in soft ground material such as oil sands.

Jan 1, 2012

By Greg Johnson

Maintenance needs information about assets to optimize availability and production needs information about performance and consumption to maximize output. In considering both these needs together as, ?Asset Optimization?, the information systems that support them are critical. The theory of Asset Optimization derives from the Lean Manufacturing concepts developed by Toyota, but some changes are required to apply this to mining operations. In particular, mining operations require automated systems due to their geographic spread and they need a strong emphasis on capturing under-performance losses as well as delays and stoppages in production. Leading metal miners and coal miners alike have applied these systems to good effect in the last 10 years. The concepts developed initially in minerals processing plants are now being applied to the mines themsleves as well as the mining logistics chain. Production increases of 5?10% are achievable with the right implementation and consideration of the some key lessons learnt in the last 10 years. Putting these lessons into action is one key step in the goal of optimizing asset performance and thus utilizing the resource at lowest cost.

Aug 1, 2013

By K. Barbetti

"The carbon-in-pulp (CIP) process has been the dominant gold recovery process since the early 1980s. CIP has proven to be very adaptable for a wide range of ores and circuit configurations. The key performance indicator for CIP circuits is the minimisation of soluble gold losses to tailings, however, it is also important to operate the circuit efficiently (maximising gold loadings on carbon and minimising carbon inventory). Over the last 30 years the Curtin Gold Technology Group has studied CIP circuits as part of an on-going collaborative industry funded project (the AMIRA Gold Processing Technology Project). In the early years the project undertook basic research into understanding activated carbon, and its management in the circuit. More recently the development of process models and instrumentation has provided additional tools to assist operators. The results show that while most CIP circuits operate well, there are still significant opportunities for further cost savings, or additional revenue. This paper reviews the observations arising from this work, including key requirements for good carbon management, the results of benchmarking and industry surveys of carbon circuit over 20 years, the value of process modelling of CIP circuits to establish operating parameters, and the use of automated instrumentation to better optimise carbon control in the circuit.INTRODUCTION The introduction of activated carbon to recover gold from cyanide leach solutions in the last quarter of the 20th century was the most significant development in gold ore processing since the advent of cyanidation seventy years before. Replacing the Merrill–Crowe zinc cementation step with carbon-in-pulp (CIP) or carbon-in-leach (CIL) circuits provided a process that allowed the treatment of lower grade and problematic ores (e.g. high-clay ores), at lower capital and operating costs, and higher metal recoveries. The CIP circuit was first developed in the 1950s at the Carlton Mill, Cripple Creek, Colorado. All the components of the modern CIP process came to fruition at the Homestake Mine in South Dakota in 1973 (Fast, 1988). From the late 1970s onward a variation of CIP, carbon-in-leach (CIL) which combined the leach and adsorption stages, became the preferred circuit design in most parts of the word."

Jan 1, 2017

By M. Silva, G. Olivares

In a leach pile, the drainage layer or commonly known as the cover layer has been a matter of discussion due to the multiple phenomena or events that occur within it which impacts negatively the leaching process. All these events are directly related to the loss of draining capacity and irregular flow net due to an excessive compaction and entrapment of fines reducing the flow velocity which in turn cause more fines to get trapped. Over time the problem will continue to worsen rapidly and accelerating continuously like a geometric progression. When the cover layer gets to a certain level of deterioration, the only alternative to continue operating safely is to replace the entire cover material, a huge cost for any mining operation. TESRA has developed a solution to counteract the accelerated advance of the deterioration of the drainage layer. The solution consists of using large agricultural tractors coupled to a proprietary design of a heavy- duty subsoiler-ripper for deep tillage for loosening and breaking up the ground at various depth and with different legs spacing from 0.4 m or above. Also, if the ground still requires additional breaking, TESRA proposes the use of a rototiller that breaks any lumps to homogenize the ground to a certain particle size. With the subsoiler-ripper/rototiller combination equipment a layer of 0.5 m deep is properly treated to match closely the original conditions of the ground thus regaining the flow net as close as to the original seepage condition. Once the ripping is completed the subsoiler-ripper tool is replaced with another that is similar to a plow and thus continue with the installation of drainage pipes. The tool digs a Y-type profile trench allowing the pipe to sit precisely at the bottom of the trench, contributing additional lateral and lower support. This tool controls the installation depth of the drainage pipe at different inclination grades and also eliminating any irregularities that may block the flow of the leaching solution. Sometimes the obstructions block completely the flow of the solution. The main result of this methodology is the reduction of groundwater levels and at least 2% less humidity in the leaching gravel due to an increase in the draining capacity of cover. The methodology developed by TESRA applied during a couple of cycles of a dynamic leach pile has proven to be a real alternative to remedy and recuperate the cover close to its original conditions. The methodology requires only one large tractor and two accessories operated in different stages while replacing the more traditional and less efficient machinery such as the Bulldozer, Motor-grader, and backhoes.

Jan 1, 2019

By G. S. Crawford

Forecasts prepared by the B.C. Research Council for the National Harbours Board suggest that mineral shipments through B.C. Lower Mainland port facilities will increase more than four-fold, from 6 to about 25 million tons, during the decade 1965 to 1975. The longer term outlook is for a six-fold increase to about 35 million tons by 1985. In 1967, minerais accounted for more than one-third of the total deep-sea traffic tonnage, nearly as much as grain. By 1975, the minerals' share will be about half the total. The principal items are exports of potash from Saskatchewan, and of coal and sulphur from Alberta and British Columbia. Additional exports include copper and other mineral concentrates and propane. Imports are chiefly salt and phosphate rock. Coastal traffic in such items as cement, sand and grave!, and limestone totalled 3.3 mil-lion tons in 1967. They will continue to be of major importance, but do not have the spectacular growth potential of the deep-sea traffic.

Jan 1, 1968

By M. L. F. Paullo, S. Cristian Mejia, D. Roehl

"Rock fracture simulation most often presents non-linear behaviour due to loss of material integrity and strain concentration in the fracture zone. These strains generate local instabilities that propagate to the global system of equilibrium equations, generating convergence problems of the numerical solution. Often, in such cases, analyses in the post-critical regime are unfeasible. To overcome the numerical difficulties associated with problems of stiffness loss in the post-critical regime control methods, also called continuation methods, are employed. Among them are the arc-length method, the energy control method and the indirect displacement control method. These methods are employed in conjunction with a Newton- Raphson scheme for the solution of non-linear systems of equations. However, depending on the system instability, convergence in not guaranteed even with very small increments. In the present work these control techniques are investigated in combination with cohesive elements to simulate rock fracture. The constitutive model employed with the cohesive elements represents stiffness degradation through a damage law, which leads to serious convergence difficulties as reported in the literature. Here the continuation methods mentioned are applied to a Mode I rock fracture problem and to hydraulic fracture simulations. The effectiveness of the different continuation methods is compared.INTRODUCTIONThe process of rock fracture induced by the fluid pressure is called hydraulic fracturing. The propagation of a hydraulic fracture is a complex process, which is basically defined by the mechanical deformation of the rock, the fluid flow within the fracture and the fracture propagation itself (Mokryakov, 2011). In the works of Bendezu et al. (2013), Chen (2012) and Carrier et al. (2012), vertical hydraulic fracture propagation is modeled by cohesive elements with traction-separation law. The softening behavior of rock in post-critical regime is demonstrated by experimental testing and is characterized mainly by high strains and low stresses (Crowder and Bawden, 2004). This nonlinear behaviour can arise due to material nonlinearity, such as micro-cracking and damage, leading to softening behaviour (Chandrakant, S.D., 2012). The cohesive fracture model considers in its formulation the softening behaviour that most rocks present in post-critical regime with propagation criteria."

Jan 1, 2015

By Michael Godard, Peter Cleyle

"Suncor Energy’s Project Millennium increased oilsands production capacity by an additional 95,000 barrels per day to its present level of 225,000 barrels per day. This massive venture included an expanded Mine, new Extraction and Upgrading facilities, as well as, steam and utilities infrastructuresIn the Primary Extraction process, removal of the bitumen from the oil sand begins with slurry preparation and is followed by primary , secondary and tertiary separation processes. The final cleaning step of the bitumen froth is the Secondary Extraction process, that removes residual water, mineral and solids to produce a clean diluted bitumen suitable for Upgrader feedstock.This paper will review the flowsheet of the Millennium Primary Extraction facility, from its recent commissioning through the ramp up to design production rates. In addition, new technologies in the Primary Extraction flowsheet will be reviewed.INTRODUCTIONAs conventional supplies of oil and gas are depleted in Canada, the Athabasca oil sands industry of Alberta becomes an increasingly important source of energy. Today, high quality crude from Alberta’s oil sands accounts for roughly 30% of Canada’s daily petroleum production. According to government projections, over the next 7 years, oil sands production is expected to more then double, and by 2010 more than half of Canada’s crude oil is expected to come from the oil sands.Oil sands deposits consist of a layer of sand saturated with bitumen covered by a muskeg overburden and underlain by silt and clay. The oil sand is mined where the overburden is economical to remove, typically less than thirty meters thick. The Athabasca oil sand deposits around Fort McMurrray is ideal for mining. Bitumen can be described as a diverse collection of hydrocarbons, organosulfur, and nitrogen compounds."

Jan 1, 2004

By J. D. R. Neilsen

The objective of the research conducted and presented herein was to determine the effect of pre-established free gas saturation on the sweep efficiency of an isolated inverted five-spot well pattern. The investigation concluded that the ultimate recovery of an isolated inverted five-spot may be slightly increased by establishing a free gas saturation prior to water flooding; however, of more significance is the extreme deviation of the pattern's performance after water break-through from that commonly obtained from developed well patterns. The rapid "water-out" characteristic common to both linear floods and floods conducted in developed well patterns was not evidenced in the isolated inverted five-spot. Instead, the wells continued to produce oil long after breakthrough until ultimate areal sweep efficiencies of four, five, and six hundred percent were obtained prior to the water-oil ratio becoming excessive.

Jan 1, 1962

Heap leaching accounts for around 20% of the global production of copper. In heap leaching coarsely crushed ore particles are contacted with an aqueous lixiviant percolating through large packed beds (heaps) of the ore particles, with the loaded solution collected at the foot of the heap for metal recovery, solution make-up and recycle. While dominant for copper oxide acid leaching, it finds application also in copper sulphide (bio) leaching. Despite their apparent simplicity, heaps are in fact complex chemical reactors in which a number of competing sub-processes determine the overall rate of metal extraction. Therefore, meaningful prediction of copper production rates from heaps, as well as operational optimisation and control, all hinge on a comprehensive and quantitative understanding of these complexities. The paper gives a comprehensive overview of the various sub-processes in copper heap leaching and their interactions, including those relating to mineral-particle-solution-gas phase interactions at the micro-scale bulk transport and distribution of solution in unsaturated dense beds at the macro-scale. On the basis of a more fundamental understanding and modelling, the potential for optimized operation offers new opportunities for the extraction of value from both low-grade and complex polymetallic ores. INTRODUCTION Heap leaching is one of the percolation leaching technologies, which includes in situ leaching, dump leaching, heap leaching and vat leaching (Bartlett, 1998). The common phenomenon in all these technologies is the transport of leach solution through a fixed bed of ore particles, which interacts with the solid as it migrates along its path. The target minerals are released into solution and with its flow are carried out of the bed. The targeted dissolved metal species are recovered from solution through various hydrometallurgical techniques, especially solvent extraction (SX), before the barren solution is returned to the leach process. Heap leaching is practised in three main types of applications: sulphuric acid leaching of copper oxide ores, cyanide leaching of gold ores as well as the oxidative acid leaching of secondary copper sulphide ores, usually with the assistance of certain microorganisms and, more recently, in the presence of chlorides (CaCl2, sea water). While gold heap leaching dates back to the 1960s, large scale copper heap leaching commenced in Chile from the 1980s, and sulphide heap leaching emerged essentially as a consequence of acid leaching from mixed oxide/sulphide ores from the 1990s (Watling, 2006).

Jan 1, 2019

By D. J. Hallbom

This paper presents a novel methodology for the hydraulic design of mine backfill distribution systems. The ?operating range? method uses the concepts of the hydraulic grade line and equivalent pipe length to determine flows and pressures as the pipeline route and static head change over the life of the mine. The operating range method is easy to learn because it is semi-graphical and uses well-known design concepts (e.g., the hydraulic grade line) and slurry design models (e.g., the Durand deposition velocity model). However, by changing the paradigm in which these concepts are used, the operating method allows all potential pipeline cases to be analysed simultaneously without the need to know the exact pipe routing. It also allows the hydraulics engineer to quickly identify ?pinch points? and ?slack flow? zones, to estimate the effect of changing the size or length of any given section of pipe, to assess the impact of changing the material properties of the backfill slurry, to size the slurry pumps, and to size and locate rupture discs when required.

May 1, 2007

By G. D. Just

"Extensive mechanization of underground mining operations, improvements in blasting technology and the development of simulation models for systems evaluation has now made it feasible to optimize rock fragmentation and materials handling operations. Methods of achieving these objectives are described in this paper, with particular emphasis on the need to obtain precise field data measurements. Techniques are illustrated with reference to the sub-level open stoping system of mine production. IntroductionThe primary objective to be achieved in any mining system is to deliver a specified grade of ore to the mineral processing plant at a planned delivery rate and at the minimum total mining cost. Design and management of such a system is complicated by the large number of unit operations and the often unknown inter- relationships between the different unit processes. This particularly applies in underground mines, where planning restrictions and unit costs are much greater than in comparable tonnage sur face mining operations. These difficulties can often be resolved by the application of judgment based on extensive experience, but the costly trial -and-error methods required for new technology discourage innovation.Most modern medium- and large-scale mines are now extensively mechanized. Consequently, the performance of each unit operation by individual items of equipment should be predictable for a given set of conditions. An essential prerequisite is that quantitative performance data are available from field measurements. Such information can then be used to optimize the design and management of the complete mining system to achieve the minimum tot al mining cost. One of the most significant factors influencing all unit costs is the degree of rock fragmentation. The importance of this variable is indicated by the fact that opt imization of rock fragmentation implies minimization of tot al mining system costs."

Jan 1, 1980

By K. M. Deen, E. Asselin

Hydrometallurgical processes, i.e., Cu extraction from a mineral concentrate and Zn electrowinning, are coupled in a battery-like system. A naturally-sourced CuFeS2 concentrate mixed with activated carbon is used as a positive slurry electrode separated by a membrane from the negative compartment. The Zn is deposited on the negative Al current collector from the circulating solution containing 100 g L–1 Zn2+ in 0.2 M H2SO4. In this battery-like system, both CuFeS2 oxidation and Zn deposition are possible during the charging cycle. The additional benefit of this setup is the energy storage if discharged by re-dissolving the Zn in the negative compartment. Cyclic charge/discharge testing revealed oxidation of the mineral concentrate supported by the Zn2+/Zn redox reaction. The coulombic and energy efficiencies increased monotonically to 95.6% and 43%, respectively, with approximately 7% Cu extraction during the first 10 charge/discharge cycles (completed in 2.4 hours). The discharge energy density also increased from 2.7 to 36.2 mWh L–1. In the following 90 cycles, the low energy (~14%) and coulombic (~33%) efficiencies that were obtained confirmed the progress of irreversible reactions e.g. Cu extraction from the mineral concentrate. Overall, approximately 16% Cu was extracted from the mineral concentrate over 100 charge/discharge cycles (or about 12.2 hours). INTRODUCTION Chalcopyrite (CuFeS2) is the main economic copper-bearing mineral, which is generally processed through pyro-metallurgical methods to produce Cu. However, environmental challenges with smelting, depletion of high-grade ores and a large number of impurities (some toxic) have resulted in continued research aimed at the development of hydrometallurgical technologies to process CuFeS2. There are a number of different proposed hydrometallurgical routes in the literature to treat CuFeS2 concentrates, but only a few have attained commercial acceptance (Dreisinger, 2006). Zn is another commercially important metal that is mainly produced via acid leaching of roasted sphalerite (ZnS). The pregnant leach solution is rigorously purified to remove all the soluble metal impurities, particularly those that are electrochemically more noble than Zn and present large kinetic activity towards H2 evolution (Hu & Piron, 1992; Mackinnon, Brannen, & Fenn, 1987; Mureşan, Maurin, Oniciu, & Gaga, 1996). Metal impurities such as Cu, Co, Ni, Cd, Pb, Sb, As, Ge and Fe etc., if they exist in the leach liquor beyond the tolerance limits, can decrease the current efficiency during electrowinning and deteriorate the deposit quality (Alfantazi & Dreisinger, 2001). A complete flow sheet, describing the process steps of Zn metal production from mine site to pure metal is presented elsewhere (Brown, Meisenhelder, & Yao, 1983).

Jan 1, 2019

By P. W. Percival, J. J. Janssens

"Whitehorse Copper is a 2600-ton-per-day underground copper mine located within the city limits of Whitehorse, Yukon . In early 1978, due to increasingly difficult ground conditions. it was decided to investigate the conversion from longhole open stoping to vertical crater retreat mining. On-site crater testing by C-I-L demonstrated the feasibility of V.C.R. mining at Whitehorse Copper.After some investigation. a down-the-hole drilling rig was chosen and drilling began in November /978. Blasting began in June /979. and to September 1980 approximately one million tons of ore had been blasted. In-field changes to both drilling and blasting techniques have been implemented. Some of these changes were dictated by problems encountered; others were made to improve efficiencies.To date. V.C.R. mining has proven successful from a drilling and blasting aspect.IntroductionWhitehorse Copper Mines Ltd ., a division of Hudson Bay Mining and Smelting Co., Limited , is a 2600-Lp.d. underground copper mine. The plant site is located I mile west of the Alaska Highway, and approximately 7 miles south of Whitehorse city center. Production is from the Little Chief orebody, and total output is from vertical crater retreat stopes.The Little Chief and Middle Chief orebodies at Whitehorse Copper had original reserves in excess of 6 million tons, most of which graded 2.00/0 copper or higher . The orebodies are typical skarn deposits that have developed along the contact between an intrusive diorite and a limestone-quartzite flank pendant. The limestone has been metasomatized to form a calcium-magnesium skarn which, along the limestone / quartzite contact, has locally further developed into a mineralized magnetite-serpentine skarn. The principal copper minerals are bornite and chalcopyrite, with minor chalcocite and valleriite. Skarn gangue minerals are serpentine, diopside, garnet, epidote, calcite and wollastonite. Appreciable values in gold with some silver are present and recovered as well."

Jan 1, 1981

By F. P. Yungwirth

"IntroductionTrout Lake Mine is located about 5 km north of the Hudson Bay Mining and Smelting Co., Limited complex at Flin Flon, Manitoba. The mine was brought into production in 1982at the onset of a severe recession in the base metal market. The mine is operated as a joint venture with HBM&S, MMR and SMS.During the first several months of operation it became evident that there were opportunities to reduce costs at the mine significantly, and a productivity improvement subcommittee was formed to make recommendations. The first committee met in January, 1983 and consisted of the mine manager from Hudson Bay Mining, a geological expert and a maintenance expert from Outokumpu Oy, Finland, and a mine manager from Granges, Sweden.Recommendations from this committee were implemented during 1983 and a new subcommittee was constituted in 1984 to continue the work begun the previous year. The committee remains as constituted in 1984 and meets quarterly.The committee consists of M.A . Kirby , manager - Flin Flon Mines, HBM&S; Gustav Hoberstorfer of Mindelco , a Swedish mining consultant retained by Granges; Eero Laatio, mine superintendent of Keretti Mine at Outokumpu Oy in Finland; and Bob Bray, a mining consultant retained by Manitoba Mineral Resources.Many productivity improvements made in the operation are attributed to the work of this committee and other experts retained at various times throughout the mine life."

Jan 1, 1988

By R. W. Lawrence

Sulphide is an effective reagent in the precipitation of base metals for both metal winning and environmental control. BioteQ Environmental Technologies Inc. has successfully demonstrated in industrial plants that biogenic sulphide reagent can be generated cost effectively and used to win metals such as copper, zinc and nickel from low-grade leach solutions and wastewater. Commercial plants in which sulphide reagent is used to produce high quality treated effluents for discharge directly to the environment are also in operation. Operations utilizing biogenic sulphide reagent for copper recovery from acid drainage and low grade leach solutions are discussed, including those at Bisbee, Arizona, commissioned in 2004 and at the Dexing mine in China, scheduled for commissioning in 2007. In addition, a new application of BioteQ's technology for the recovery of copper from gold-cyanide solutions, and the regeneration of cyanide, utilizing biogenic sulphide in place of chemical sulphide reagents in the SART process is described.

Jan 1, 2007

By J. W. Scott, G. G. R. Falkenberg

"The Syncrude project is an integrated complex designed to mine, extract and upgrade bitumen from the Athabasca tar sands to produce 129,000 barrels per day of synthetic crude oil. This paper provides a brief general description of the location, history and geology of the tar sands and the overall organization and structure of the project. The major emphasis and the bulk of the detail presented deals with the extraction plant; a material handling and mineral processing installation designed to treat 312,000 tons per day of tar sand feed.History of the Tar SandsThe Athabasca tar sand deposit was recorded in 1788 by Peter Pond, however the first serious geological mapping and exploration did not begin until 1915. Little interest was taken in the deposits until the Second World War, when the governments of Canada and Alberta conducted an extensive exploration program. In addition a number of pilot plants were sponsored during the 1940 -1950 decade. The hot water separation process was successfully demonstrated on the pilot plant scale during 1948 -49, and was established commercially in 1967 in the G.C.O.S. plant. The Syncrude plant, due to come on stream in April 1978, also employs the hot water separation process."

Jan 1, 1978

By Robert B. Parsons

"For the fourth time in five years, residents of northern Canada have seen a change in the tax treatment of housing and travel costs. The latest changes announced in December 1990 by the Minister of Finance are to become effective in 1991. When will the tinkering stop?IntroductionFor man y years prior to 1987, certain travel and housing allowances received by employees in remote areas were generally considered by Revenue Canada to be tax-free, even though some observers suspected that such generous treatment was contrary to the provisions of the tax legislation. In the mid-eighties, Revenue Canada decided to reconsider the tax treatment of the mining industry's long standing practice of providing housing and travel assistance to these employees. The tax- free treatment was continued by virtue of annual remission orders, but only pending the enactment of legislation which would tackle the issue head-on and layout the rules in black and white to be seen by all. The sequence of events since then may be chronicled as follows:February 26, 1986-Finance Minister Wilson's budget present s the framework for the future tax treatment of travel and housing benefits provided to residents in remote regions of Canada.December 22, 1986-The Minister of Finance announces detailed rules to fill in the earlier announced framework.January 1, 1987-The new tax rules come into effect.April 29, 1988-The Minister of Finance announces the establishment of a Task Force to examine the existing criteria for determining the eligibility of residents of northern and isolated areas for tax benefits.October 27, 1989-The Task Force presents its report.December 7, 1990-Finance Minister Wilson announces a new system of tax benefits for residents of Canada's northern and isolatedregions.January 1, 1991-The new rules become effective."

Jan 1, 1991