Search Documents

By Stephen J. Roberts

Gold catalysts were prepared on co-precipitated, calcined copper oxide - zinc oxide support by an inverse deposition-precipitation method. These catalysts were characterised by X-ray diffraction (XRD) and temperature-programmed reduction (TPR) and studied for CO oxidation activity at various catalyst calcination temperatures. TPR studies of the support material exhibited a double peak and shift to lower temperatures for the reduction of Cux+ to metallic copper, as opposed to the single reduction peak for pure CuO. This phenomenon is possibly caused by an interaction with the zinc oxide. The addition of gold to the support CuOZnO led to a further shift in copper reducibility to lower temperatures. Gold present in the initial uncalcined catalyst as Au3+ was auto-reduced to Au0 under various calcination temperatures. The Au3+ reduction peak was observed to shift to lower temperatures with increasing calcination temperature. The catalytic activity was found to pass through a minimum value with respect to calcination temperature. Catalysts with both gold in entirely the 3+ or metallic oxidation state were found to exhibit high activity. Furthermore, the catalysts were found to decrease in activity with decreasing Au3+ content up to an intermediate calcination temperature, afterwhich the activity increased sharply. Possibly at higher temperatures, a stronger Au-support interaction is formed, leading to a new active site.

Oct 1, 2003

By W. E. Coates

The social ecology of surface mining in urban areas is illustrated by a case study of a recent application for the opening of a new gravel pit in the city of Guelph, including the design of a progressive extraction-rehabilitation sequence for the property, investigation of the ecological impact of the proposed operation, history of the application procedure for a zoning change and the relationship of the operating plan to provincial legislation controlling surface mining.

Jan 1, 1972

By Y. Qi

A cell-level nonlinear dynamic model of solid oxide fuel cell (SOFC) based on physical diffusion principles is built in this note. It demonstrates that reactant diffusion processes from gas flow bulks to triple phase boundaries (tpbs) play an important role in the dynamic behaviors of SOFC. The simulation shows that under certain condition, the effect of the double layer capacitance may be neglected. The phenomenon of slow rise of voltage in current interrupt experiment may be explained by the dynamic behaviors of partial pressures in the vicinity immediately above tpbs.

Jan 1, 2005

By Elma van der Lingen

Gold is considered the most inert of all metallic elements, but the metal can show catalytic activity when prepared by specific techniques. Preparation techniques being used to prepare gold catalysts systems mainly involve precipitation methods incorporating gold compounds or complexes. This paper introduces a totally different method for the preparation of gold-based heterogeneous catalysts that can be used for oxidation and reduction reactions, as well as electrocatalysts. The method involves alloying of gold with a less noble metal, such as aluminium, to form a gold-containing intermetallic precursor. AuAl2 was produced by melting gold and aluminium together in a vacuum arc furnace under a protective atmosphere. The aluminium is then dissolved from the AuAl2 precursor by means of NaOH to produce a highly porous gold structure. The paper also reports on a method of incorporating transition metal oxide(s) with the porous gold to form an active heterogeneous catalyst. Promoter elements can also be melted with AuAl2 to improve catalytic activity. Alloying has the advantage that the promoter element can be in contact on atomic level with the gold. In-situ xray photoelectron spectroscopy (XPS) studies have also been done on the porous gold catalysts to further clarify the CO oxidation mechanism on gold-based catalysts.

Oct 1, 2003

By E. M. De Souza, A. M. Coode

"Since potash was discovered substantial rock mechanics research has been done to develop the technology needed to cope with the unique conditions in Saskatchewan mines, to assure general mine safety and to assess the problems associated with mining potash at depth.The practical result of this research was the development of multiple entry systems incorporating yielding pillars for access ways and the chevron type layouts for production panels. These developments proved the viability of extracting potash from between 950 m and 1100 m depth using a high degree of mechanization. High extraction ratios could not, however, be achieved using the developed technology.The presence of a competent salt back is critical to mining the potash, and underground practice is governed by the presence of anomalous geological zones. These factors may be associated with the occurrence of brine inflows. One potash mine in Saskatchewan ceased its underground operations and was closed due to flooding of the entire mine. Two other potash mines in Saskatchewan had significant brine inflows. The costs involved in brine pumping, equipment relocation, bulkhead construction, grouting, and in auxiliary operations can run into the tens of millions of dollars.At Central Canada Potash, the use of stress relief and yielding pillars in the design of the mining layouts has resulted in over-all stable underground excavations and safe mining practices. There are two types of production room s, the chevron and the hybrid, which result in a planned block average extraction ratio of 35010. Mining activity has resulted in brine ingresses in two areas, and additional operating costs have been incurred over the years. These mining areas have demonstrated abnormally high closure rates, and rapid back deterioration. A program was established in those two areas to ensure the practice of safe mining procedures.The short-term perspectives inherent in the program included the elimination of all uncertainties associated with the possibility of an increase in brine inflow leading to flooding, the elimination of the abnormal ground behaviour and ground deterioration in the inflow areas, and the reduction of the long-term adverse effects of mining on regional mine stability. The program was also designed to provide means for developing alternative safe mine layouts which would improve the exploitation of potash resources. Details of the extensive work performed during the program are found elsewhere (E. De Souza, 1988).Grouting and salt backfilling are viable techniques to control brine inflows in underground excavations in potash mines. Detailed instrumentation of the backfilled test areas provides information on the long-term behaviour and effectiveness of the grout/backfill system, allowing for rational decisions on the complete abandonment of these mined out areas, thus resulting in considerable operational cost savings.This paper is presented in two parts: the first addressed the problems of diamond drilling , grouting and backfilling in Panel 209 and the second, addresses the problems of instrumentation and rock mechanics."

Jan 1, 1990

By Belinda Campbell

Tools for Consistency 1. GIS Web Site 2. National Project Management System 3. Site Grouping Approach (721 PIDs) 4. Mine Reclamation Standing Offer Agreements ?Contracting tool 5. Remedial Objectives Guidance Document Background ?CBDC (now ECBC) is a Federal Crown Corporation and falls under federal jurisdiction. ?When it stopped mining coal, CBDC turned its attention to cleaning up and closing out its industrial sites. ?Public Works and Government Services Canada is common service provider to the GoC. ?Expertise in environmental, engineering, IT, project management, communications, GIS, real property management.

May 1, 2011

By Fabian Mohr

The methyl substituted binuclear cyclometallated gold(I) complexes [Au2(?-n-MeC6H3PPh2)2] [n = 4, 5 and 6] all undergo oxidative addition reactions with halogens and, in the case of the 4- and 5-methyl substituted analogues, with dibenzoyl peroxide to give metal-metal bonded digold(II) complexes [Au2X2(?-C6H3-n-MePPh2)2]. The 4- and 5-methyl substituted digold(II) compounds on warming or exposure to light undergo carbon-carbon coupling reactions to give gold(I) complexes containing the corresponding 2,2'-n,n'-biphenylyldiphenylphosphines. The 6- methyl substituted digold(II) complexes rapidly isomerise above ca. -20° C to binuclear heterovalent gold(I)/gold(III) compounds [XAu(?-2-Ph2PC6H3-6-Me)AuX{?2-(6-MeC6H3-2-PPh2)}], containing a fourmembered cyclometallated ring on a gold(III) centre. Surprisingly, no carbon-carbon coupling could be induced for any of the 6-methyl substituted compounds, even under forcing conditions. This difference in reactivity of the 6- methyl derivative, compared to that of the 5-methyl and unsubstituted analogues was studied by ab initio calculations using a series of model compounds. The results are in excellent agreement with the experimental findings and suggest that the key-step in the C-C coupling reaction is the partial opening of the Au(III)-P bond in one of the transition states. In the 6-methyl system this transition state is energetically inaccessible and hence no C-C coupling occurs.

Oct 1, 2003

The Discrete Element Method (DEM) is a powerful tool for analysing the flow of charge, the energy consumption and the pattern of energy utilisation of a SAG mill. With the development of laser scanning measurement, the detailed internal working surfaces of a SAG mill can now be included in DEM models. Using scanned results for new and worn shell liners for a 32? (9.75 m) SAG mill, it is shown that the feed and discharge lifters have significant effect on the flow of the charge introducing significant threedimensionality. The effects of the resolution accuracy of liner geometry and the lower cut-off of the rock size distribution are explored. Finally, using a matched new and end of life worn liner and operating conditions taken from site surveys, the effect of wear on charge motion, distribution and energy utilisation are evaluated.

Jan 1, 2012

By Filipe Beretta

This study investigates geophysical logging capacity to predict coal quality. It was analyzed for possible correlation, some parameters determined via laboratory analysis of coal against results for the same parameter derived from wireline logs recorded by a geophysical probe. These probes detect variations in some rock physical properties, such as their natural gamma ray emissions and electrical resistivity. Results showed a strong correlation between natural gamma and ash content, establishing a linear model to estimate ash content from geophysical logging data with a low estimation error (less than 5%). Besides, results showed that there is no correlation between sulphur content or volatile matter and resistivity, neither with natural gamma of the rocks. Ash content derived from gamma ray values can be used as secondary information to evaluate coal quality during resources estimation, using methods such as soft indicator kriging. The methodology is illustrated using a case study at a coal deposit in south of Brazil.

Oct 1, 2009

By Ross G. Bertinshaw

"The Line Creek Mine of Crows Nest Resources started mining coal in the fall of 1981. There are seven mineable seams with thicknesses ranging from 1.5 to 13 metres and with dips varying from 0 degrees to 60 degrees. This, together with internal partings and the very friable nature of the coal, creates a number of mining problems.The coal is divided into zones depending on the dip of the seam. Each zone requires a different mining technique to ensure optimum recovery and low dilution while still keeping fines to a minimum.Line Creek employs a combination of hydraulic front shovels and backhoes to mine its coal without blasting or use of dozers. This has been very successful in reducing the proportion of fine coal hauled to the plant, thus improving quality control and reducing costs in coal processing.There have been a number of other benefits from the use of excavators instead of more conventional methods. These include better selectivity, good cleanup, reduction in traffic at the face and lower cost.IntroductionThe Line Creek Mine is situated approximately 25 km north of Sparwood in southeastern British Columbia (Fig. I). Preproduction stripping began in J98J with the first coal shipments made in 1982. In 1983 the mine produced 2.1 million tonnes of raw coal.Similar to other East Kootenay coals, the seams at Line Creek are characterized by their friability, producing a large proportion of fine coal during mining. In an attempt to reduce these fines Crows Nest Resources has instituted the use of hydraulic excavators to mine and load the coal.Hydraulic excavators offer other substantial advantages over front-end loaders and dozers, which has been the conventional system in other mines in the area."

Jan 1, 1985

By Arne Renström

A fleet management system such as Minestar with CAES and Aquila could basically be defined as a tool for production control and distribution of drill and load maps, but should also be considered as continuous improvements and a never ending production study. The objective of production studies is to establish facts to be used for production improvements. In a mine operation there are many issues to improve and they spread from achieving productions plans, drilling precision, improved spotting while loading to equipment utilisation. This gives that there is not one single key value to present; we need to manage information presented on maps, as trends, graphs, tables and pre-calculated data for ?free-use? normally in spread-sheets to be able to turn data into useful information.

May 1, 2003

By S. k. Kim, H. B. Trinh, R. R. Srivastava

"Spent auto-catalyst is a promising secondary resource of platinum group metals (PGMs), which are being extensively used in automobiles catalytic converters to control the hazardous gaseous emissions (CO, NOx and hydrocarbons). Several pyro or hydrometallurgical routes has been employed to recover PGMs from such spent materials but there is no proper process for recovering the other constituents metals. Therefore, it causes the loss of other major constituents like, Al and Mg along with rare earth metal Ce. In the present study, we investigate the dissolution of Al and Mg using sodium hydroxide (NaOH) roasting followed by a sulfuric acid (H2SO4) leaching; thereby concentrating the PGMs and Ce in leached residues. The effect of roasting temperature, time and amount of NaOH were varied. Subsequently, the dissolution behavior of metals in H2SO4 as a function of acid concentration was investigated from the roasted samples. At an optimal condition for roasting at 600°C with 1:1 NaOH-to-catalyst ratio and 60 min duration, the maximum of Al and Mg were dissolved in 1 M H2SO4 solution at ambient temperature (~25°C). Thus obtained leached residues containing enriched PGMs and Ce content can be treated separately for the recovery of these high-value metals.INTRODUCTION Spent auto-catalyst has been considered as a potential resource for recovering the platinum group metals (PGMs) (Jha et al., 2013). The commonly used auto-catalyst is made of cordierite (2MgO.2Al2O3.5SiO2) in which the chloro complexes of PGMs are impregnated onto the surfaces of porous washcoat of alumina substrate (Aberasturi et al., 2011). The average concentration of PGMs in ore are 2-4 g/ton for Pt, 7-2 g/ton for Pd and 0.2-0.5 g/ton for Rh, whereas, an individual catalytic converter weighing about 1 - 2 kg contains on average 1.56 g Pt, 0.62 g Pd and 0.156 g Rh (Upadhyay et al., 2013). Moreover, recovery of PGMs from spent auto-catalyst offers other advantages like, simple process, low cost and less pollution, as compared to recovery from primary resources (Dong et al., 2015).Therefore, technologies to recover PGMs from spent auto-catalyst has become attractive in the recent past and their recycling contribution has been accounted for 35% Pt, 26% Pd and 36% Rh of the quantity consumed in the production of auto-catalysts (Johnson Matthey, 2016)."

Jan 1, 2017

By Hasan Ozturk

Laboratory testing examined the effect of a variety of intrinsic rock properties and environment conditions that influence the adhesive bond between rock and thin spray-on liners. The liner materials used for these tests were Tekflex, provided by Fosroc, Castonite, provided by Rohms and Haas Co., Rockweb provided by Spray-on Plastics, and CS 1251 2K, provided by Master Builders. Some of the variables examined include: rock strength (tensile/compressive strength) rock mineralogy, rock surface roughness (grain size, fracture/joint roughness), and surface contamination (oil, water or dust). Under optimal conditions, adhesive strengths reaching at least 3 MPa can be achieved. Where the rock surface is contaminated with dust or the rock is weak in tension, it may be difficult to reach adhesion strengths of 1 to 1.5 MPa.

May 1, 2004

By K. Woo

The increasing move to block cave mining methods (including sublevel and panel caving) to access deeper and lower grade ore deposits as near surface sources become exhausted raises questions as to the extent and magnitudes of caving-induced subsidence as it may affect strain-sensitive infrastructure on surface. Predicting these surface deformations is difficult as they tend to be discontinuous and asymmetric due to large movements around the cave controlled by geologic structures, rock mass heterogeneity and topographic effects. Of further impediment is the sparse number of case histories available, in which actual subsidence measurements are reported to provide guidance and empirical constraints for subsidence calculations. This study reports the development of an exhaustive and comprehensive database of available (i.e. public domain) subsidence data from block cave mining operations from around the world.

May 1, 2009

By J. T. Liu, G. H. Han, W. C. Chai, Y. F. Huang

"In beneficiation process, metal ions could adsorb onto clay mineral surfaces or interact with flotation chemicals, and then result in the flotation behavior changing of desired minerals. Al(III) is the dominating ion existing in the bauxite flotation system. In this research, the adsorption behaviors of Al(III) on two silicate clay minerals (including bentonite and kaolin) were investigated by means of UV-Vis spectra, zeta potential testing and scanning electron micrograph analysis. The adsorption experiment results show that the adsorption capacity of clays for Al(III) ions increases with the initial Al(III) concentration, contact time and solution pH. There are some different adsorption behaviours for two clays. Increasing the clay concentration decreases the adsorption capacity of bentonite, while increases first then decreases for kaolin. Higher temperature favours the adsorption of Al(III) on bentonite but goes against for kaolin. The adsorption capacities of bentonite and kaolin for Al(III) respectively reach 12.48 and 0.875 mg/g at initial solution pH 5. Zeta potential results show that the adsorption of Al(III) on two clays is characterized by electrostatic attraction mechanism.INTRODUCTIONIn beneficiation process, there is inevitably a wide variety of metal ions generated from mineral crushing, mineral dissolution and water chemistry conditions. Metal ions adsorb on the mineral surfaces or interact with the beneficiation agents, affecting the flotation efficiency of desired minerals (DiFeo et al., 2001; Parolis et al., 2008; Shackleton et al., 2012; Shengo et al., 2014). Therefore, it is necessary to have a detailed investigation on the adsorption behaviour of metal ions on clay minerals.Having good ion exchange capacity and negative surface charge, the clay minerals could take up various metal ions from the mineral-water system. Bentonite and kaolin are very common aluminosilicate clays in the mineral processing system. These two clays both hold a permanent negative charge, =X- on the basal surfaces, and a smaller variable charge, =SiOH on the mineral edges (Gu & Evans, 2008; (Gu et al., 2010). Adsorption experiments are usually used to study the adsorption affinity of metal ions for clay minerals (Sen & Bhattacharyya, 2012). The adsorption of Zn(II), Cu(II) and Pb(II) onto natural bentonite showed that the adsorption amounts of metal ions increase with contact time, solution pH and metal ion concentration, but decreases with adsorbent concentration and system temperature (Sen & Gomez, 2011; Melichova & Hromada, 2013). Cr(III) adsorption on bentonite was significantly pH dependent. The adsorption process followed pseudo-second-order model and the equilibrium adsorption was consistent with Freundlich isotherm (Lollino et al., 2015). The adsorption behaviours of Pb(II), Cd(II), Ni(II) and Cu(II) onto kaolin indicated that increasing pH favoured the adsorption of metal ions (Jiang et al., 2010). The adsorption of Cd(II), Cu(II), Pb(II) and Zn(II) onto kaolin showed that an ion-exchange reaction occurred at pH<7.0 and inner-sphere surface complexes were prone to form at higher pH (Srivastava et al., 2005)."

Jan 1, 2016

By K. Norris

"The Campbell mill has undergone numerous changes over the past 43 years. However the rate of change has increased significantly in the last 4 years. A new grinding circuit, carbon-in- pulp circuit, pressure oxidation plant, and column flotation circuit are all new additions. Other changes have occurred in the last 2 years including a large reduction in sodium cyanide consumption, and the introduction of a computer controlled grinding circuit. More improvements are planned in the next 2 years. Some of these improvements include the construction of an effluent treatment plant, and the replacement of filtering and Merrill-Crowe precipitation with carbon-in-leach and electrowinning.Recent changes and improvements to the Campbell mill are a commitment by Campbell mill personnel and Placer Dome Inc. to decrease operating costs, increase gold recovery and gold production, improve industrial hygiene and safety, and meet environmental compliance with current government legislation.INTRODUCTIONThe Campbell Mine has been and continues to be one of Canada's premier gold mines. Campbell Mine is 100% owned and operated by Placer Dome Incorporated. Milling of ore commenced in 1949 at a rate of 300 tons/day producing 58,000 ounces per year of gold. In 1992 Campbell Mine will mill 1340 tons/day of ore at a grade of 0.6 ounces/ton, producing 275,000 ounces of gold at a cash cost of $205.00 Cdn./ounce.This paper discusses some of the changes that have been made to the Campbell mill in the past 4 years. The flowsheet has undergone extensive changes and will continue to change rapidly in the next 2 to 3 years. A simplified flowsheet of the Campbell mill is shown in figure 1."

Jan 1, 1992

By A. R. Kinkel JR.

"The Buffalo Ankerite mine is in the southern part of the Porcupine gold district of northern Ontario. The mine has a history of exploration and development reaching back to 1911, and has been operated continuously since 1932. From 1932 to 1942 a total of 510,874 oz. gold was produced from the mine. In 1941 the production was 71,654 oz. from 448,621 tons of ore.With few exceptions, the ore-bearing veins did not crop out. They were discovered during the prospecting of the prominent outcrops of barren or low-grade quartz-carbonate breccia near the veins.GEOLOGICAL SETTINGThe Porcupine gold district lies in an area of folded and sheared Precambrian lavas, sediments, and intrusives. The Buffalo Ankerite mine is in the southern part of a large fold. The structure appears to be a continuation of the Vipond cross anticline and accompanying syncline described in earlier papers (1, 2). The orebodies lie along both flanks of the synclinal part of the fold, and are known as the north and south vein systems, respectively. No mineable veins have been found on the axis of the syncline (Fig. 1).The rocks found in the mine area are pillow lava, dacite, conglomerate, quartz porphyry, tuff, and fragmental lava. The tuff and fragmental lava are now largely altered to chlorite schist. Productive veins have been found only in pillow lava, dacite, and conglomerate, but a minor amount of gold occurs in some of the quartz porphyry. The Porcupine Creek fault, a zone of intense shearing over 1,000 feet in width, lies immediately south of the mine. A spur fault branches to the northwest from the Porcupine Creek fault, separating the north from the south vein systems ( Fig. 1) ."

Jan 1, 1954

By M. Rigaud, N. Zhou, K. Sankaranarayanane, X. Zhou

The effect of amount and type of dispersants on the rheological behaviour of bauxite-based low-cement castables has been studied in detail. The rheological properties: flow resistance and torque viscosity, as measured by a rheometer, are found to be strongly influenced by the amount and type of dispersants. In the present investigation, a mix containing sodium hexametaphosphate, at an optimal level, is observed to be theologically superior at the given experimental conditions.

Jan 1, 2004

By Christopher Andreae

"Years before the present iron and steel works were established at Sydney, several thriving although short-lived iron work s operated in Nova Scotia. These furnaces reflected the general nineteenth-century North American experience with iron work s. At the beginning of the century, small furnaces struggled to supply local needs. Charcoal was the principle fuel and water powered most furnace equipment. By the end of the century, a few huge primary iron and steel work s dominated production for Nova Scotia and the rest of Canada.Two sites achieved prominence in the nineteenth-century Nova Scotia iron industry: Londonderry and Ferrona. Londonderry, the larger and longer-lasting of the two sites, is today a small village on the south flank of the Cobequid Mountains, about 30 km west of Truro. Prior to the establishment of an iron works in 1849, no community existed. At the peak of operation in the 1880s, however, over 2,600 people were located there. The second site, Ferrona, today is a mere crossroads on the map, about 10 km south of New Glasgow. Following the construction of a blast furnace there in 1892, a small village grew up around the furnace, but once the furnace was blown out in 1904, the population gradually drifted away.Early HistoryThe history of Nova Scotia&apos;s iron industry began in 1604 when Samuel Champlain became the first European to identify iron ore in the future province. Despite this early acknowledgment, iron was not smelted commercially in Nova Scotia for another two hundred years. Although primitive smelters of the period produced more iron than could be used locally, early settlers depended on imports of iron from Britain and the United States."

Jan 1, 1983

By A. S. H. Kabir, I-H. Jung, J. Su, Yue. S., M. Sanjari

One of the major problems associated with conventional wrought magnesium alloys is the unwanted basal texture that forms during plastic deformation which generally does not change markedly after post-deformation annealing. Formation of precipitates on the recrystallized grain boundaries during annealing may affect the usual rotation of grains towards preferred basal direction resulting in texture weakening. In this study, Mg-Al-Sn alloy was hot compressed at 250°C and annealed at 350°C for various times. The initial as-deformed microstructure was partially dynamic recrystallized with dynamic precipitates on the grain boundaries. After annealing at 350°C, static recrystallization of the bimodal microstructure took place where at this temperature no static precipitates formed. The goal of this work was to study the effect of dynamic precipitation on the texture evolution during the annealing process. Texture evolution was studied during annealing by electron backscattered diffraction (EBSD) technique through a microstructure tracking process. It was found that precipitates on the recrystallized grain boundaries have significant effect on the usual rotation of the grains towards the basal direction, meaning significant texture weakening, which is beneficial for final mechanical properties.

Jan 1, 2015