Search Documents

By L. Torres, C. S. R. Rondestvedt, M. Bustos

In February 2010, Teck’s newest Concentrator at Mina Carmen de Andacollo (CDA), Andacollo, Chile was commissioned. The Concentrator is a single line configuration, comprising of one 36 ft diameter x 20 ft long SAG mill driven by an 18,000 hp gearless drive. The SAG mill feeds two ball mills each 25 ft in diameter x 40.5 ft long, each driven by a total of 19,000 hp through dual pinion drives. A series of four phases will be reviewed from operational readiness, mechanical completion, commissioning, and ramp-up. Also, now after 6 months of operation, this paper will review the significant steps taken during ramp-up enabling the announcement of commercial production, in October 2010.

Jan 1, 2012

By J. G. Martin, J. C. Campbell

THE VICTORIA JUNCTION 31,4-million-ton coal preparation complex went into operation in October 1976."' It is designed to produce a metallurgical coking coal by lowering the sulphur and ash content of the raw coal using a heavy-media cycloning process to treat deslimed crushed coal, with scavenging of fine coal by flotation from the primary minus-28-mesh screen product. A secondary H-M cyclone scavenges a thermal-grade coal from the primary H-M cyclone tailing.

Jan 1, 1985

By F. Nava-Alonso, A. Uribe-Salas, C. Rodriguez-Rodriguez

Ozone has been proposed to pretreat refractory ores before the cyanidation process for precious metals extraction. As pyrargyrite is one of the silver species most common in Mexican refractory ores, the ozonization of this silver sulfide was studied. The effect of pH and ozone concentration on silver dissolution was evaluated by means of a factorial experimental design. Two levels of sulfuric acid concentration and ozone in gas concentration were evaluated: 0.18 and 0.72 mol/L of acid and 0.054 and 0.077 gO3/L, respectively. The highest silver dissolution was obtained when using the higher acid and ozone concentration.

Jan 1, 2011

By Claude Bazin, François Robichaud

The control of the operation of a semi autogenous grinding mill is mainly based on power and bearing pressure measurements. Image based sensors can provide on-line measurements of the size distribution of the ore feeding a SAG mill allowing the control of this variable that impacts the operation of this equipment. This paper investigates the potential of using the information from such type of sensor to maintain a SAG mill feed target size distribution by manipulating the speed of the ore extractors below an ore stockpile. A PID and adaptive predictive controller for the size distribution are studied using a simulator for a stockpile and the equipments used for ore withdrawing from the pile. The proposed controller is found to give a good performance while remaining easy to tune.

Jan 1, 2014

By Xiao Huang, Dongmei Wang, Prakash Patnaik

Further increase in gas turbine engine temperature necessitates continuous development and advancement to thermal barrier coatings. While tremendous effort has been devoted to developing new thermal barrier coating materials and processing methods in order to decrease the thermal conductivity, limited attention has been paid to radiative thermal transport through coatings. It is the purpose of this study to develop a new layered coating structure that can be used to effectively reduce the both radiative thermal transport as well as thermal conductivity, and to demonstrate the mechanism and effectiveness of the proposed multilayered structure. Mathematical modeling based on the multilayer quarterwave stack and simulation results are presented.

Jan 1, 2004

By F. Flynn, P. Downey, G. Ritson

"Bell Creek Mill which has been in continuous operation since 1987 has undergone numerous operational changes in the past three years. The addition of over 2. 5 million tons of resource at over 13 git from Hoyle Pond Mine precipitated an expansion program for the Bell Creek Mill. This paper discusses the major changes that have occurred over the past two years to increase throughput and efficiencies. In addition, the refractory ore treatment options are also discussed.IntroductionThe Bell Creek Mill is located in the Timmins Goldcamp approximately 8km NE of porcupine Ontario. (Fig I.)The mill was originally constructed by Camamax in 1987 to treat the Bell Creek ore at a design throughput of 350tpd. The flowsheet (Fig 2.) consisted of two stage crushing, grinding, thickening, leach and drum filtration with gold recovery by Merrill Crowe.As ore depleted at Bell Creek, the Mill was purchased by Falconbridge to process ore from their Hoyle Pond property. Kinross purchased the Hoyle Pond property and Bell Creek Mill from Falconbridge in 1992.The successful exploration program at Hoyle Pond has led to several expansions and process design changes, with further changes planned over the next twelve months.In 1994, the mine produced 61,865 oz. of gold at an average cost of 197US$ per oz. In 1995 production was 91, 611 oz. at a cost of 187US$ per oz. Projecting the nine months ended September 30, production for 1996 will be 155,000 oz. at a cost of 165US$ per oz.In early 1997, the CIP expansion will be complete, with a target of 175,000 oz. at a cost of 176US$ per oz for 1997. The mill throughput will have increased from 400tpd to 1500tpd between 1994 and 1997.The changes to Bell Creek since 1994 have been numerous with very little of the existing equipment still in operation. The total cost of the expansion to date is 15 million C$. This paper discusses the major projects carried out during in this time. The focus will be to highlight the justification of each project, the design and engineering, some of the initial start-up problems and solutions.Figure 3 shows a plan of the existing mill facility together with the various additions that were carried out."

Jan 1, 1997

By Patrick R. Taylor, T. A. R. Putra

A review of various methods to treat high arsenic copper concentrates through pyrometallurgical processing is presented. Examples are drawn from various past and current operations and research. Various aspects of the engineering alternatives for treatment methods are discussed. Some of the methods discussed include: controlled oxidation roasting, adaptation of some smelter technology to accept higher amounts of arsenic, complete oxidation with arsenic fixation; sulfation roasting; acid baking, soda ash roasting, and others methods. Other topics include: a short discussion of other problematic impurities; the effects of arsenic on copper electro-refining and product purity; and methods for the ultimate disposal, or marketing, of the arsenic. The latest work being done at the Colorado School of Mines on soda ash roasting is also presented.

Jan 1, 2014

By R. Ramirez

Atlantic Copper Refinery (Huelva, Spain) has operated the ISA permanent cathode technology since 1995. The current production rates are 260,000 t/y cathodes and 730 t/y anode slimes. These slimes undergo an atmospheric leaching in which their copper content is reduced from an average value of 24 % to 16 %. In June 2005 an optimization study of the leaching conditions was carried out aimed at lowering the copper content in the slimes to less than 8%. At the same time, a new mixer (Outukumpu Technology GLS-mixer) was installed in one of the three leaching reactors. As a result of the improvement of the leaching performance and to prevent the return of tellurium to the tankhouse, a cementation plant was commissioned in July 2005 to ensure a Te content below 50 ppm in the Cu-rich leachate. This paper describes the results of the improvement of the leaching conditions and the operation of the new tellurium removal plant.

Jan 1, 2007

By J. E. Moran

A groupd of French capitalists, La Compagnie Française des Mines d'Or du Canada, has undertaken the considerable task of developing Otter creek, in the Atlin district, B.C., by hydraulic mining methods. It has long been known that the gravels of this stream carry sufficiently high values in gold to make it attractive as a mining venture, but it was impossible to ignore the existence of formidable natural obstacles to hydraulicing them, and these needed to be taken into serious account before embarking upon any costly programme of development. The tide to the Otter Creek leases was originally held by Mr. H. Maluin, a French engineer well known throughout the north, to whom was to fall the task of financing whatever programme might be decided upon. It was he, too, who would have to assume the responsibility of finally passing judgment upon the practicability of the various devises for overcoming the adverse natural conditions. With an infinite attention to detail, which I believe to be a characteristic of the French people generally, he studied his problem and was finally able to submit to his financial backers a programme which left the very minimum possible to the hazard of accident or chance. Dr. Mandy, on his visit to Otter creek this season, expressed the opinion that our method of opening this difficult creek presented certain features which might be successfully applied in placer operations elsewhere in British Columbia, and it is largely for this reason that the present paper has been prepared. I shall set forth, as well as I can, the practices which have enabled us to overcome rather easily some of the obstacles which nature had unkindly placed in the path which we must take. The natural flow of water in Otter creek is far too little to deal success-fully with the rather excessive amount of glacial drift overburden which lies directly over the gold-bearing gravels. For this natural defect, the only remedy was to procure more water. This we have clone through a system of flumes and ditches, totalling between ten and eleven miles in length, which bring to the mine a supply of water adequate for our needs.

Jan 1, 1932

By R. D. Lindsay

Originally the focus of Deak Resources Corporation Business Plan was to establish a method for treating small gold and possibly base metal mineral deposits located in the Kirkland Lake - Noranda area of Northeastern Ontario, Northwestern Quebec at a central treatment facility. Since the establishment of this original business plan in 1988 other processing options have availed themselves for handling the base metal ores off site at a central facility which may preclude their processing at Deak.The site selected for the Deak processing plant was Kerr Addison's Virginiatown operation. At the time this property was acquired from the Receiver following Golden Shield Resources' Bankruptcy in 1989 the mill had been processing in the order of 1, 100 SDT per calendar day through one processing module; a module originally designed to process 1,500 SDT/day of a free milling gold ore. This tonnage level however had not been achieved since 1966 when an average throughput of 1481 SDT per calendar day was recorded.In order to realize Deak's overall Business Plan it would be necessary to expand the mills processing capabilities to provide:(1) A 2200 SOT per day circuit capable of processing a free milling, medium work index gold ore;(2) a 1 ,000 SDT per day flotation and/or cyanidation circuit capable of processing refractory gold bearing materials containing refractory minerals (i.e. copper) that should be removed prior to cyanidation; and possibly(3) a 1200 to 1500 SDT/day base metal circuit capable of processing the broad range of Deaks' Base Metal Property ores. If this circuit were introduced it would be completed in two tonnage phases.Further, it was recognized when operations resumed under Deak in 1990 that the existing tailings dam was suitable for, and had sufficient capacity for additional gold tailings with necessary physical modifications and changes in disposal techniques (including the construction of containment storage cells) that would allow storage for an additional 3.4 million tons of gold ore tailings approximately 1.0 million of which has been deposited since 1990. The focus of Deak's long term tailings disposal strategy is to acquire the Barber Lake Basin which is currently adjoined to our main tailings system which will provide an additional 10 million tons of storage capacity.

Jan 1, 1993

By D. Raicevic

After more than 93% of the uranium is extracted from Elliot Lake uranium ores by a sulphuric acid leaching process, the leach residue (tailings) contains small amounts of uranium and radioactive isotopes, particularly radium-226, which is the most serious health hazard. Heavy metal components and pyrite are also present, along with the gangue minerals. Currently, over /000 acres of the Elliot Lake area are covered with these tailings, which contain over five million tons of pyrite. Because of constant oxidation of the pyrite by bacteria (thiobacillus) and the presence of moisture, pyrite slowly generates sulphuric acid, which steadily leaches the metal-bearing constituents from the tailings. The seepage-flows of the dissolved contaminants, although often quite low in volume, have an environmental impact on the Elliot Lake area. Although these seepages are treated and most of the contaminants removed and impounded, a small amount of the radioactive contaminants reaches Lake Huron via the Serpent River. This paper describes a flotation approach for treatment of the Elliot Lake uranium tailings to produce new, decontaminated tailings practically free of pyrite, with radium, thorium and uranium contents considerably reduced. The decontaminated tailing produced, which comprises about 75% by weight of the current uranium tailings, appears to be suitable for mine backfill. Because mine backfilling normally uses about 50% of the plant tailings, the surface storage of about half of the uranium tailings, therefore, would be eliminated by this process. Mine backfilling would also increase the mine production and thus enlarge the over-all uranium resources due to recovery of the ore from pillars. The pyrite concentrate produced from the current uranium tailings would be suitable for sulphuric acid production. The possibility of uranium recovery, and disposal of radium and thorium from the concentrates produced, is now being studied at CANMET.

Jan 1, 1979

By William Shaw

Conditional simulation is now an accepted tool for managing ore block design at a number of operating mines. It provides a way to consider the quality of data, local continuity and economic risk in defining ore and waste across the cut-off boundary. In addition a computer based system can ensure consistency in making decisions to meet multiple criteria such as cut-off grades, minimum ore-block size and contaminant grade limits. The development of a procedure for using multiple criteria allows ore blocks to be defined using alternative strategies depending on the specific production requirements. This has introduced the opportunity to define ore blocks for different destinations based on their material types and opens the way for geometallurgical modelling to be incorporated into grade control.

Oct 1, 2009

By Samantha Beeson, Collin Poole

"This paper examines the development of two new selective flocculation techniques for recovering KCI values from low grade carnallite potash ore.Direct recovery of KCI was achieved using one of two mid-range molecular weight polymers, one non-ionic and the other strongly cationic, in conjunction with the same selective anionic dispersant. From initial response studies on pure minerals and selective flocculation tests on synthetic mixtures, investigations were extended to recover KCI values from a natural carnallite potash ore. A single-stage process achieved products grading up to 61.3% KCI at recoveries up to 85.4% for the cationic flocculant suite and up to 64.8% KCI with recoveries as high as 90.3% for the non-ionic flocculant suite, with dispersant and flocculant dosages of 150-250gr1 and 10-75gr1, respectively. These results clearly demonstrate not only the feasibility of treating such problematic ores at low reagent dosages, but also the potential elimination of desliming prior to froth flotation.The experimental results presented are considered in terms of the reagent adsorption phenomena present in the system and various aspects of floe formation and cleaning.IntroductionAs high-grade sylvinite potash ores become scarce, lower grade sylvinite and carnallite potash ores are becoming more attractive. However, these ores often contain large amounts (up to 15% by weight) of water-insoluble slimes which must be removed prior to KC! flotation, owing to their high adsorptive capacity for the amine collectors used. The slimes are generally removed by scrubbing followed by hydroclassification and any residual material not eliminated is blinded with reagents such as guar gum or starch to inhibit interference in subsequent KC1 flotation.An alternative approach used commercially in Canada by Agrium Inc. involves water-insoluble slimes flotation prior to KC! flotation. In this process, the slimes are selectively flocculated and then separated by froth flotation. Losses of KC! to the slimes product and associated brine requirements are both reported to be less than those encountered in conventional desliming, but the technique is somewhat limited in its application at present."

Jan 1, 1997

By P. Cielo

"Nondestructive inspection is an important quality control tool in the material processing industry. Being nondestructive, such a control may be applied to the whole production, as long as the available techniques are fast and easily automated. Ideally, nondestructive testing (NDT) methods should operate in a noncontact configuration in order to be deployable on-line with minimum perturbation of the production process.After a short introduction to the most common NDT techniques, with particular emphasis on ultrasonic, radiographic and electromagnetic methods, a few new approaches which are under development at the Industrial Materials Research Institute, (Boucherville, Quebec), are reviewed. Noncontact techniques such as laser ultrasound, thermoelastic and thermographic methodologies will be described, and their applications to materials of industrial interest will be discussed."

Jan 1, 1989

By O. Kangal, G. Önal, G. Bulut, A. Gül

The recovery of copper and cobalt from the ancient copper slags, located in Küre-Turkey, is investigated. Fayalitic type of ancient copper slags containing 1.41% Cu, 0.53% Co and 53.16% Fe were subject to the experimental study. Magnetic separation, gravity concentration and flotation test were conducted. The results of magnetic separation and gravity concentration were not satisfactory. However, a concentrate containing 9.57% Cu could be produced with 44.7% recovery by flotation. Copper and cobalt that remained in the flotation tailings was recovered by roasting with sulfuric acid followed by hot water leaching. Complete cobalt dissolution was observed in 1 hour of roasting at 150°C and 3:1 acid/slag ratio, whereas the copper recovery was 83%.

Jan 1, 2004

By S. N. Dixon

"Maximizing the value of each tonne of processed ore is the goal for all operations. Cyanidation processing of gold-copper ores has been challenging since its first use in 1889. The current practice treats a bleed or the total flow of mill solution to recover copper as copper sulfide (by sulfidization, acidification, recycling, and thickening), or to recover the cyanide (by acidification-volatilizationneutralization). The process presented uses the adsorption of copper cyanide by carbon and the selective elution of copper from carbon to concentrate copper into a smaller stream. Copper contained in the smaller stream is precipitated as copper cyanide.RÉSUMÉ Toutes les exploitations ont pour objectif commun d’optimiser la valeur de chaque tonne de minerai traité. Depuis sa première utilisation en 1889, la méthode de traitement par cyanuration des minerais aurifère et cuprifère s’est révélée complexe. La pratique actuelle traite la saignée ou le débit total d’une solution de traitement du concentrateur pour récupérer le cuivre sous la forme de sulfure de cuivre (par sulfuration, acidification, recyclage et épaississement), ou pour récupérer le cyanure (par acidification, volatilisation et neutralisation). Le procédé présenté dans cet article utilise l’adsorption sur charbon actif de la solution de cyanure de cuivre et l’élution sélective du cuivre depuis le charbon pour concentrer le cuivre en un plus petit jet. Le cuivre contenu dans ce plus petit jet est précipité sous forme de cyanure de cuivre."

Jan 1, 2017

By V. Caps

Gold has been often used as an alloying component in order to increase or modify the catalytic properties of an active metal. For example, in the hydroconversion of methylcyclopentane, Riahi et al [1] shown that the addition of gold to palladium or platinum enhances the activity which becomes greater than that of the pure metals whereas the selectivity towards products resulting from ring expansion increases. Molenbroek et al [2] presented a detailed study on Ni-Au catalysts which exhibit activity for steam reforming and have been proved to be more resistant toward carbon formation than the pure Ni catalysts. Blocking of highly reactive Ni edge and kink sites by Au atoms is assumed to be the reason for the increased robustness of the Ni-Au catalyst. Nevertheless, the own catalytic properties of pure gold have been almost ignored up to the pioneering work of Haruta et al [3] which demonstrates the high activity of gold for CO oxidation at low temperatures. Other reactions such as WGS reaction, propylene epoxidation or benzene total oxidation have then been shown to be catalyzed by gold [4]. This discovery induced the publication of papers devoted to analyze the different factors controlling the activity of gold catalysts. Among them the most relevant appears to be the gold particle size, the nature of the support [5] and the preparation methods [6]. Clearly distinguish between support and size effect is not straightforward. Indeed, the calcination step often needed to synthesize supported catalysts on different supports, leads to different particle sizes showing that particle size and support are interdependent. To circumvent this difficulty, Au-based supported catalysts have been synthesized by using laser vaporization and low energy cluster beam deposition. The as prepared catalysts have then been characterized and tested in CO oxidation reaction.

Oct 1, 2003

By Marc Ruest

A new instrumented cable bolt has been developed by the National Institute for Occupational Safety and Health at the Spokane Research Laboratory in Spokane, WA. Although various instruments are available to measure load distribution and magnitude along a grouted cable, this instrument is innovative in that it uses strain gauges internal to the cable as load-measuring sensors. The instrument has been successfully tested in the field at FMC?s Granger Mine, Meikle Mine, and Getchell Mine. A ?split-pipe? laboratory pull test was performed on each of three cable bolts instrumented with the new device. Each test consisted of grouting a 1.83-m-long cable in two 0.91-m-long sections of schedule 80 pipe. A numerical analysis was then performed in which laboratory boundary conditions were simulated and model properties derived from textbook guidelines. The loads calculated by the model were then compared to the measured loads.

May 1, 2002

By G. Plascencia, A. Warczok, M. Zamalloa, T. Utigard, N. Behnood

The objective of this investigation was to investigate interactions between high-grade copper mattes and Rexal 60DB direct bonded basic bricks. The infiltration and attack of Rexal 60DB bricks by copper matte and continuous converter matte was investigated in laboratory tests at temperatures up to 1300 °C. The brick dissolution and infiltration tests did not show any significant difference between the 70% Cu and the 81% Cu mattes. More metallic copper was visible in the pores in the case of 81% Cu matte. An important mechanism for direct-bonded magnesia-chrome brick destruction is that oxysulphides start to infiltrate the brick, followed by slow oxidation of the matte producing metallic copper and cuprous oxide, which then react with MgO and Cr2O3, primarily attacking the direct bonds of the brick.

Jan 1, 2004

By M. A. Bérubé, M. Choquette, P. W. Godbehere

"RESUMELa scorie produite par le procédé pyrométallurgique d'extraction Noranda contient environ5% de cuivre. Elle est traitée comme un minerai conventionnel de cuivre au concentrateur de Mines Noranda et les rejets de flottation présentent encore des teneurs souvent supérieures à 0.3% en cuivre. La scorie est principalement constituée de magnétite, de fayalite et d'un verre siliceux. Bien sûr, Ie cuivre y est majoritairement sous forme de sulfures et d'un peu de cuivre métallique. Le verre contient toutefois un peu de cuivre en solution, de 0.14 à 0.33% en moyenne, selon l’echantillon examine, ce qui représente à peine 1% de tout Ie cuivre de la scorie. Dans les rejets de flottation, cela justifie par contre de 15 à 25% des pertes totales en cuivre, Ie reste se retrouvant sous forme de tres petits globules de sulfures de cuivre ou de cuivre métallique, en moyenne de 2 à 3 micromètres de diamètre et bien emprisonnes dans Ie verre.SUMMARYThe slag produced by the Noranda continuous smelting process usually contains about 5% copper. It is processed as a conventional copper ore at the concentrator of Noranda Mines. The flotation tailings still often contain more than 0.3% Cu. The slag is mainly constituted by magnetite, fayalite and a siliceous glass. Evidently, the copper occurs mostly as sulphides and, to a lesser extent, as metallic copper. However the glass contains a small amount of this metal in solution, between 0.14 and 0.33% on an average, depending upon the investigated sample. This represents scarcely 1% of the total copper in the crude slag, but as much as 15 to 25% of this metal in the flotation tailings, in which the major part of the copper occurs as very small globules of copper sulphides or metallic copper with an average diameter of about 2 to 3 um and well-locked in the glass."

Jan 1, 1987