Search Documents

By Z. Zhang, M. -Y. Liu, X. -G. Chen, F. Breton

"The microstructures of AlSi10Mg foundry alloy in permanent mould (PM) and high pressure vacuum die (HPVD) castings were analyzed and compared. The as-cast microstructures of two castings mainly consisted of eutectic silicon particles, primary Mg2Si and Fe-rich intermetallic phases. The surface layer in HPVD castings, which has a unique feature and different structures, was carefully characterized. The dimension variation of microstructural phases along the cross section in PM samples is less than that in HPVD samples, although the size of microstructural phases in PM samples was much larger than that in HPVD samples. The mechanical properties of PM and HPVD samples were evaluated on as-cast and T6-treated conditions. The tensile properties of HPVD castings are remarkable better than those of PM castings on the as-cast condition. The T6 heat treatment greatly improves the tensile strength of PM castings while it has limited impact on the tensile strength of HPVD castings.INTRODUCTION The AlSi10Mg alloys are widely applied to the high pressure die casting (HPD) and high pressure vacuum die casting (HPVD). In the HPD process, the melt is injected into the die cavity under a high speed (30–50 m/s in the gate velocity for aluminum alloys), and solidified under a high pressure (up to 200 MPa in the cavity) and with a high cooling rate (up to ~103 Ks–1) (Gourlay, Laukli & Dahle, 2007; Ji, Wang, Watson & Fan, 2013). This results in a unique microstructure feature that is different to other casting processes under gravity. One major concern in HPD castings is porosity due to trapped air in the cavity (Ji et al., 2013), which seriously restricts the application of a heat treatment on the improvement of mechanical prosperities because of the formation of blisters on casting surfaces. For the process improvement, the high pressure vacuum die casting was developed in 1980s (Uchida, 2009). In this process, the melt is injected into the die cavity under reduced pressure (vacuum), which greatly reduces gas porosity in castings due to effectively avoiding the trapped air. Consequently, HPVD castings are heat-treatable without the formation of blisters on castings surface during heat treatment. The HPVD process has been widely applied to produce high quality structural castings in recent years attributed to reliable vacuum system development (Uchida, 2009). However, the microstructure features of HPVD castings are not systemically characterized yet."

Jan 1, 2018

Inco Limited has been evaluating options for streamlining the overall flowsheet at its Sudbury, Ontario operations to improve productivity and to minimize the cost of at¬mospheric emissions reduction. Some of the flowsheets being considered include vari¬ous levels of copper/nickel separation at the Clarabelle Mill where all Inco's Sudbury Basin ores are processed. This paper reports on the laboratory and miniplant studies car¬ried out during the flowsheet development for a commercial Cu/Ni separation plant. There are two potential feed streams for Cu/Ni separation. It was determined that Cu/Ni separation from the rougher concentrate requires no regrind, and a very clean copper concentrate is produced, but the recovery of copper is limited to about 70% from ore. Cu/Ni separation is more difficult from the bulk concentrate because of the presence of excess flotation reagents in the slurry and due to locked particles. By replacing the slurry water with clean process water, and by addition of some hydrogen peroxide, entrainment is minimized and excess reagents are removed from the surface, providing a satisfactory separation of copper from nickel. Fine regrinding is required to increase liberation of the locked particles and to obtain 85% copper recovery with minimal nickel contamination of the concentrate.

Jan 1, 2005

By S. Power Warren

Introduction It is generally conceded by flotation men that the condition at the surface of a particle of mineral or gangue is the most important factor controlling its behaviour in a flotation cell. Much research work has been devoted to the study of the forces that are active at the surface of the particle and of the effect of the surrounding solution upon these forces. Study of the relationship between mineral or gangue particles and gas bubbles indicates that, in the main at least, flotation is a physical phenomenon. The important factor, that of mineral-gas-bubble attachment, is unquestionably physical; however, modifications may be effected by chemical means, whereby the nature either of the surface of the particle or of the surrounding solution may be changed. For example, the coating of lead sulphide that forms on lead-carbonate ore particles when sodium sulphide is added greatly aids the flotation of the carbonate particles. Without going into the question as to why, under certain surface conditions, mineral particles will attach themselves to gas bubbles whereas under other conditions they will remain unaffected, it may be stated that there are three general conditions in a flotation pulp which control the attachment of the particle and the gas bubble.

Jan 1, 1933

By A S. Leitch

This paper is based on the accident prevention pro-gram carried out in the coal mines of Alberta. It defines the role of the Alberta Mines Branch and of The Work-men's Compensation Board, and relates how a safety pro-gram was initiated. The formation of the Alberta Class 1 Mining Safety Council is also described. The responsibilities of both management and the individual worker are then outlined, and the main features of a successful accident prevention program are delineated. T HE purpose of this paper is not to repeat generalities and platitudes about industrial safety, but rather to relate the experience of Alberta coal mines during the past number of years in their efforts to keep accidents to a minimum. It has been learned from experience that many basic principles are as sound today as they were 20 years ago. How-ever the complexities of modern mining methods and the modern man or miner have created problems that did not exist then.

Jan 1, 1964

By Larry M. Southwick

There have recently been executives at major metals companies who have recommended that Greenfield Projects not be pursued. Greenfield includes not only new geographical locations, but also new technologies and new types of feed materials. In the middle part of the 20th Century, two such projects were successfully commercialized to recover nickel from Cuban lateritic ores. One project (at Nicaro) used the Caron ammonia-ammonium carbonate leach and the other (at Moa Bay) a high pressure acid leach. How both of these projects dealt with these Greenfield issues will be reviewed, based on the original reports that described the research and development of the plants. This study will include a review of the critical ore characterization and sorting issues, as well as the extractive metallurgical, product recovery and equipment selection and sizing problems and how they were solved at each stage of project development, from laboratory through one or more pilot scale plants to start up and operation. In one case, a major revision of the plant was made after several years of operation to correct operating, equipment selection and materials of construction problems that hindered economical operation. These descriptions will provide a guide through the complicated and critical issues that in recent times have caused many companies to give up on similar development. Even with the more advanced analytical and computational tools available to today’s mineralogists, engineers and metallurgists, the basic concepts with which these projects successfully addressed their sets of problems are still required. In addition, upper management, now perhaps further removed from hands-on experience than was common then, will see how complicated problems require intense and detailed effort to avoid failure in the field and capital blowouts. Build it and we will make it run, kicking the can down the road and borrowing operating and design concepts incorrectly on technological issues, or nine year olds on a sugar high making financial decisions are not philosophies by which to succeed with Greenfield Projects.

Jan 1, 2014

By P. L. Wright

"This is a brief history of the development of the mining project, with a description of the proven geology. The paper describes how the experiences gained progressively demanded change in the mine design. The equipment used is described, together with methods of working. Interesting facts have been proved regarding gas emissions and roof. supi;iort. The. working cycles evolved are completely flexible m operation and lend themselves to maximum utilization of the most productive units. The two underground mines are compared, showing the variance in conditions already experienced. Programs currently in operation to improve standards and production are: the training of miners, maintenance men and officials; experiments in floor consolidation and continuing roof support trials; and the effect of comparative stability of working crews on the performance of the operation."

Jan 1, 1973

By K. B. Hodgins, P. Ouellette

"The North American mining industry faces challenging emissions regulations in the coming years with the introduction of new standards for off-road diesel engines. In order to remain competitive, industry stakeholders must invest in new technologies that are economically and environmentally sustainable.Westport Innovations Inc., Vancouver,British Columbia, has developed high-pressure direct injection (HPDI) technology that allows diesel engines to run primarily on natural gas with no intrusive engine modifications while reducing emissions of nitrous oxides (NOx), particulate matter (PM), and CO2 with no loss in performance. This is accomplished through late-cycle, high-pressure direct injection of natural gas into a diesel engine combustion chamber at the end of the compression stroke. A small amount of diesel fuel is injected first to initiate combustion, followed by the natural gas fuel main injection. The diesel cycle and its operating characteristics are fully retained including high combustion efficiency, lowspeed torque, high-power output, no engine knock, and fast response to load changes. Natural gas has not been an attractive fuel alternative in mining operations due to the reduced performance associated with spark ignition engines and the added weight and space required for compressed natural gas tanks. However, liquefied natural gas (LNG) can be stored with less impact on weight and space than compressed natural gas (CNG) by virtue of its increased energy density over CNG.Westport has applied HPDI technology to the Cummins QSK series engines for high horsepower applications such as power generation and mine haul trucking. HPDI can also be applied to other engine manufacturer platforms and market applications. Westport is interested in demonstrating the unique characteristics of HPDI in mine haul trucks to show diesel performance with low emissions levels using low-cost LNG fuel.Retrofitting a Tier 1 engine with HPDI would provide emissions reductions below the EPA 2006 Tier 2 standards while maintaining the performance and efficiency of the Tier 1 platform. The longer-term target is the Blue Sky voluntary standards of 3.8 g/kW-hr (2.8 g/bhphr) of NOx + non-methane hydrocarbons (NMHC), and 0.12 g/kW-hr (0.09 g/bhp-hr) of particulate matter (PM) and future standards. Typically, an HPDI engine is capable of reducing NOx emissions by 40% over diesel operation at the same efficiency. On a mining truck meeting Tier 2 standards, this NOx reduction would translate into NOx emissions approximately 14 t per year lower than under diesel operation. PM emissions are typically reduced by some 60% with HPDI fueling, which would translate into a yearly reduction of 650 kg. Similarly, engine-out greenhouse gas (GHG) emissions are reduced by 21%, resulting in a yearly reduction of approximately 950 t per vehicle.Above those of emissions reduction, efficient natural gas usage in mine haul operations would offer significant benefits in terms of fuel cost savings, which may be further combined with monetary emission credits. HPDI technology would enable operators to exercise environmental stewardship while gaining a competitive advantage in advance of new Tier 2 and Tier 3 emissions regulations. The advantages of natural gas use among mine haul truck operations can be replicated across a broad range of engines and applications."

Jan 1, 2005

By Jared Onyirimba, Jim Viellenave, Hal Demuth, Dale Verran, Chad Sorba, Errol Lawrence, David Bronkhorst

As outlined within the Denison Mines Corp’s (“Denison”) Pre-Feasibility Study ("PFS") completed in late 2018, additional work is required to increase confidence and reduce risk associated with the application of the In-Situ Recovery (“ISR”) mining method at the Phoenix deposit, located on the Wheeler River Uranium Project (“Wheeler River” or the “Project”) in northern Saskatchewan. The successful application of ISR in any geological environment largely hinges on three fundamental requirements, 1) permeability (of the deposit), 2) containment (of the mining solution) and 3) leachability (of the mineralization). Denison has designed several staged technical programs to progressively reduce risk associated with these requirements as the Company advances the Project toward a Feasibility Study (“FS”) and Environmental Impact Assessment (“EIA”). This paper will discuss the scope and results of certain technical programs being undertaken as the Company aims to develop the first ISR mining operation in the Athabasca Basin.

Jan 1, 2020

By M. Hames, K. Larmour-Ship, B. Grinbaum, E. Buchalter, R. Hackl, B. Wassink

Sodium cyanide continues to be the lixiviant of choice for gold dissolution. Many gold ore-bodies contain a significant amount of cyanide-soluble copper which increases the cost of processing due to high cyanide consumption and high cyanide destruction and disposal costs. Several cyanide destruction processes are in use today, however, there are just a few cyanide recovery plants operating. A solvent extraction process to recover cyanide has been developed which utilizes the organophosphorous extractants Cyanex 923, di-butyl-butyl-phosphonate (DBBP) or tri-n-butyl phosphate (TBP) in Bateman Pulsed Columns. Copper cyanide species are first converted to hydrogen cyanide (HCN) by acidification, with or without sulfide addition. HCN is extracted by the organic and stripped using a suitable base (eg. NaOH) resulting in a high strength cyanide solution (eg. NaCN) for recycle to the gold recovery process. Continuous pilot plant testwork on HCN extraction using a 40 mm diameter Bateman Pulsed Column demonstrated a cyanide recovery of greater than 99% with final levels of cyanide in solution of less than 10 ppm. These results illustrate the potential of this technology to recycle cyanide and to detoxify final effluent streams.

Jan 1, 2005

By D. J. M. Farnsworth

Since the 1.940's, the bulk of the ore production from the Sullivan Mine has come from pillars. These pillars, located from 100 to 2000 feet below surface, have been subjected to considerable ground pressure. Mining techniques were adopted to minimize the problems of deteriorating ground conditions. These techniques included an orderly sequential blasting of pillars along a retreat front, stage blasting of tall pillars in horizontal slices and utilization of broken pillars as "buffers". The latter two techniques involved leaving substantial tonnages of broken ore in place for as long as 4 years. Rapid oxidation of metal sulphides, with attendant heat and noxious gas generation, had occurred in a few very localized areas of the mine associated with a major water course. However, in a very short period starting in 1972, sulphide fires spread to several of the large blocks of broken ore that had been left inactive for lengthy periods. There proved to be no feasible method of extinguishing these fires, except by complete removal of the burning ore. The attendant problems of handling large tonnages of burning ore have had considerable negative impact on the mine operation. The chemical reactions involved in these sulphide fires have been studied by the mine staff to determine the conditions necessary for' initiation and propagation of the tires. Techniques to safely and efficiently handle hot ore have been implemented and refined. Lastly, and most important, mining methods at the Sullivan Mine have been revised to ensure that additional fires do not occur.

Jan 1, 1977

By Michel Ruel, Ali Soltanzadeh, Benjamin Légaré

High fidelity commercial process simulation packages can be used at different stages of a greenfield project, from initial plant design to operator training in the later stages. However, there are several factors that make the software less attractive for small and medium size brownfield projects, such as the licensing cost and the fact-finding manpower required for model design and simulator maintenance. In this paper a different approach is described. The knowledge gathered from operating personnel was used to implement higher level models based on plant data, operating heuristics, and experience rather than detailed component-level models. The computing platform used was a low-cost, well-established, control system vendor-independent software. Throughout this paper we demonstrate the success of implementing this model-based approach using two industrial examples. The first example is a simulation of the carbon monoxide (CO) distribution system at a metallurgical complex. The purpose of this simulator was to test new control strategies and PLC programs prior to implementation. CO being a toxic combustible gas, validation of the suggested control system changes was necessary for plant safety. Simulation of specific operating conditions helped alleviate concerns and improved plant-wide acceptability of the new operating philosophy. The second example is a boiler simulator at a petrochemical plant. The operator training simulator (OTS) was designed as a platform for experienced operators to practice handling rare or abnormal conditions. A customized medium-fidelity model was developed for this targeted application where the cost of a full scale high-fidelity model could not be justified.

Jan 1, 2016

By G. A. Witwicki

"The Thyssen Mining Group of Companies has successfully applied ground freezing technology to numerous projects throughout Europe and North America for over 100 years. Recently, the aspect of data acquisition and data verification has received greater focus.Thyssen Mining has been engaged in several relatively deep shaft sinking projects over the past five (5) years, all of which have required ground freezing to successfully sink through water bearing rock. To safely and economically sink through a quantity of water similar to Saskatchewan’s Potash Mines, it is imperative to understand freeze wall thickness and growth rate.Critical to understanding freeze wall thickness and growth rate, is the collection of accurate data as well as the interpretation of those data. The data can then be utilized to gain a better understanding of the freeze wall growth rate in active projects as well as to provide data to be utilized in modeling for future projects.This paper elaborates on the installation and operation of the data acquisition system utilized at the Newmont Leeville project, Nevada’s first frozen shaft project. In addition, this paper elaborates on the methodology developed by Thyssen Mining to manipulate the freeze wall data derived through the data acquisition system.The successful incorporation of the new system of collection and analysis of freeze wall data for the Leeville Project has given Thyssen Mining a high degree of confidence in the understanding, as well as prediction, of the ground conditions during shaft sinking.This paper will include:•,A brief description of ground freezing and its objective;•,An overview of previous data acquisition methods employed;•,Current data acquisition methods;•,Installation requirements; and,•,Data manipulation and presentation methods."

Jan 1, 2015

By Zetti Gavelán

Globalization and the search for new ore deposits inevitably lead to investment in foreign markets. Investors need to be aware of the effect of their venture on regional, social and economic issues when they invest. Decades of detailed statistics from various sources can be integrated and analyzed to predict the social-economic impact of investment, thereby mitigating risk. To this end, the correlation among variables such as foreign direct investment into mining (FDIM), reserves, and socio-economic indexes is examined. The investigation focuses on South America from 1992 to 2000. Throughout the past decade, South America has benefited from capital investment from more developed countries. This huge investment by the mining industry has impacted the South American economies and can be measured directly using the FDIM. Other economic variables investigated include mining gross domestic product, direct employment, and human development indexes. The correlation is based on data compiled from the World Bank, international risk assessment agencies, the United States Geological Survey (USGS), and the information agencies of various South American countries. Initial analysis of the economic data suggests various expected outcomes. For example, foreign investors may disregard a measured, highly negative country risk in deference to the quality of its mineral resources. It is important to note that the standard measures of country risk published by investment analysts are not industry or investor-specific. In the case of the investor, the level of accepted risk is based on their managed investment portfolio. It is noted that arguments for level-playing fields may be the antithesis of globalization. The discovery and exploitation of ore bodies in a globalized environment necessitates the development of economic measures that standardize mining-specific risk variables and trends. The latest published information on the security of mineral investments in South America is investigated by integrating databases of economic, geologic, production, human indexes, and risk ranking.

May 1, 2003

By M. Romana

"RMR geomechanics classification is being used all over the World as a useful tool for tunnel predesign and construction. Bieniawski (1989) provided guidelines for tunnel excavation and support, according RMR numerical values; guidelines which are now included in almost all tunnelling books, regulations, and Internet portals. But in the last 25 years tunnelling techniques have changed and some of the guidelines have become obsolete.. The conditions of tunnels for the 1989 guidelines application were: horseshoe shape; 10 m width; vertical stress < 25MPa; construction by drilling and blasting. Actually a substantial number of tunnels are mechanically excavated. The tunnel themselves are now bigger: a span of 14 m. is very common for transportation tunnels. The guidelines included the following concepts: excavation method, rock bolts (20 mm diameter, fully grouted), shotcrete, steel sets. There is an increasing gap between the 1989 guidelines and the practice: in many tunnels different to-the-case excavation and support requirements are established. Bieniawski himself has published a paper (Lowson & Bieniawski, 2013) with different guidelines based in Lowson’s practice, with no explanations and/or justification.In this paper a new set of RMR tunnelling guidelines is proposed taking account of the actual industry conditions, and increased safety regulations. The 5 classes’ limit RMR:values (80,60,40,20) are no more useful actually: Values of RMR (70, 50, 30) are used in practice to define quite different tunnelling techniques. Consequently a 10 subclasses system is proposed. Each subclass covers a span of 10 RMR points. As the number of mechanically excavated tunnels has increased a new correction factor is necessary, according the excavation method.The proposed 2014 RMR guidelines are for tunnels 10 to 14 meters wide, the world practice for new roads/railways tunnels. Many tunnels for water/ services are smaller with smaller support needs. Wider than 16 m caverns are out of the RMR system.It is not possible, nor desirable, to propose only a value for support in each subclass. The new guidelines propose an interval of values for certain types of support. More pessimistic values must be chosen for wider tunnels, tunnels with lower RMR values in each class and cases when a higher safety factor is asked for. More optimist ones are chosen for narrower tunnels, and higher RMR values. Some alternatives are almost complementary, others are contradictory. Sometimes several different techniques are proposed Guidelines are not automatic options. Good engineering judgment must be used when choosing between the different alternatives. Guidelines are not mandatory suggestions."

Jan 1, 2015

By Paul T. Fitzgerald

Risk financing solutions are emerging to fully address environmental liabilities for mining operations. Supported by specialized insurance and alternative risk transfer (ART) products, mine owners can fund, cap and guarantee the environmental liabilities and closure obligations of a mine within a financial structure that will be acceptable to regulators. An environmental risk financing program will permit an owner to transfer the liabilities and indeed the ownership of a site to a third party that has the ability and resources to responsibly execute the closure plan. A properly structured program will be financially viable for the owner and will also respond to community and environmental opposition concerns about sustainable development and the environmental legacies associated with mining activities.

Apr 1, 2005

By J. S. Roberts

"Campbell mines has been in operation since 1948. Part of the process consists of roasting of a flotation concentrate which contains arsenopyrite.At present operation level the milling rate averages about 850 t.p.d. and about 48 t.p.d. of concentrate is roasted. The gas emissions at present contain between 3 and 3.5 t.p.d. of arsenic trioxide, about2 - 2.5 t.p.d. of particulate matter and between 19 - 25 t.p.d. of sulphur dioxide. The particulate is extremely fine calcine dust and it assays about 4 oz. Of gold per ton.Until 1974 the gas was discharged untreated through a 125' stack.UntreatedThe decision was made in 1972 to erect a gas treatment plant, construction ran through 1973 and operation began in 1974. The cost of the installation was about 1.3 million dollars.On investigation the process technology, it was apparent that the plant operated by giant Yellowknife for the same purpose was the model we should study. I would like to acknowledge the fine cooperation we had from giant, the plant that emerged is very similar to theirs and incorporates some improvements suggested by them and based on their operating experience.The plant is designed to remove arsenic and solid dust and it has no provisions to remove sulphur dioxide.We depend upon the 125' stack to assure adequate dilution. Because of the nearby airport the stack cannot exceed 125'. A stack burner is provided that can ""y used to heat the stack gas and carry it higher into the atmosphere when there is an inversion condition.The removal of arsenic from hot gas is fairly simple. The sublimation point is about 425°f, a few degrees above this point the arsenic is a gas and a few degrees below it condenses into a solid form. The arsenic could have been removed by simply dropping the temperature below the condensation point and collecting all the solids in a baghouse. This would have removed the possibility of recovering the gold in the calcine dust and would have produced an impure and more bulky arsenic material to be placed in safe storage. The decision was made to collect the solid dust in a hot electrostatic precipitator operating above the sublimation point and subsequently lower the temperature below the condensation point and collect the arsenic in a baghouse."

Jan 1, 1976

By Michael Young, Josh Rubenstein, Michael Cooper, Tom Shouldice, Dan Curry

"Xstrata Nickel Australasia’s Cosmos plant in Western Australia is currently implementing a debottlenecking project to increase nickel output while maintaining metallurgical performance and a low unit cost for production. Mineralogical analyses indicated that the processing bottlenecks could be removed by simply reconfiguring portions of the circuit as well as adding capacity with technical advancements – notably an IsaMill™, Jameson Cell, Wemco® SmartCell™ and Larox Filter.The Wemco® SmartCell™, which is particularly suited for coarse mineral flotation, and Jameson Cell, which is particularly well suited for fast floating and fine minerals, combine as rougher scalpers to complete the main stream portion of the flotation circuit. Addition of the two new cells meet the required flotation capacity to handle the forecast increase in nickel feed grade and tonnage.The addition of an IsaMill™ for regrinding allows the SAG mill to produce a coarser primary product, thus enabling increased throughput. The advantages offered by the IsaMill™ include operation in open circuit (internal classification), an inert grinding environment (ceramic media) for better downstream flotation (“clean” new surfaces), compact footprint (easy to retrofit into existing plant) and energy efficiency. With the new rougher capacity addition, the remaining original plant cells were reconfigured to suit the new regrind mill and cleaning requirements. The existing 24 m2 Larox pressure filter was replaced with a larger 32 m2 unit to dewater the increased concentrate output.The paper describes the upgrade at the Cosmos concentrator with particular emphasis on the mineralogical data and metallurgical benefits associated with the changes.INTRODUCTIONThe Cosmos concentrator is located 680 km northeast of Perth in Western Australia. The deposit’s development and operations were started in 1999 by Jubilee Mines NL, Cosmos’ previous owner, with the first production of nickel concentrate in April 2000. The Cosmos concentrator treats a komatiite hosted high grade nickel sulphide ore, with sulphides being predominantly pentlandite and pyrrhotite with lesser amounts of pyrite and chalcopyrite."

Jan 1, 2010

By L. B. Smith

Introduction The property of Wright-Hargreaves Mines, Limited is situated at the northeastern end of Kirkland lake, Ontario. It lies immediately east of the Lake Shore mine, and about in the centre of the Kirkland Lake camp. The district is served by the Swastika-Rouyn branch of the Temiskaming & Northern Ontario railway, the town of Kirkland Lake being four miles northeast of Swastika, which is 63 miles north of Cobalt and 392 miles north of Toronto. The mine is developed by three shafts and has more than twenty-eight miles of underground workings. There are two main producing veins, which lie in a porphyry boss 1,350 feet wide. Milling started in May, 1921, and to-date (January, 1933) the mine has produced gold to the value of $21,770,183. Present production is at the rate of 800 tons of ore per day. For a description of the geology, reference may be made to the report by E. W. Todd on the Kirkland Lake Gold Area (1). Structure and Ore Deposits The two major productive veins on the Wright-Hargreaves property are known as the North vein and the South vein. In the vicinity of the shafts these veins are approximately 550 feet apart. A third vein, known as the Inclined vein, has been worked from its junction with the South vein at the 2,000-foot level to its intersection with the North vein at the 800-foot level. This inclined vein has to date been found only in the area east of the eastern major north-south fault. The main North vein and South vein have a general vertical dip, although local rolls and post-ore faults throw certain sections out of line. From the surface to 3,900 feet, the North vein is displaced south less than 200 feet, and the South vein at the same horizon is almost perpendicularly beneath the surface showings.

Jan 1, 1934

We describe a new method of characterising the effect of dissolved materials on the rate of coalescence of bubbles in aqueous media. Single bubbles were allowed to rise to meet the surface of an aqueous solution, and the time of persistence between arrival and bursting of bubble was measured as a function of solute concentration. A laser beam was placed just above the surface of the liquid, with a detector in the light path, so that any disturbance at the surface could be seen as a break in the beam. The arrival of a bubble at the surface could be detected from the behaviour of the trace on an oscilloscope, and when the bubble broke, another significant change in the signal could easily be seen. The time between disruptions was reported as the persistence time. The effect of a homologous series of n-alcohols (C1 to C8) on the persistence time was measured, in aqueous solution. It was found that with increasing concentration of a particular solute, the persistence time increased up to a point, and then declined. However the magnitude of the persistence time was found to increase with increasing numbers of carbon atoms in the molecule. Bubbles of 1, 2 and 3 mm diameter were used. Persistence time increased with increasing bubble diameter, the maximum values observed being of order 100 secs. For a given solute, the persistence (drainage) time increased with increasing bubble diameter. The concentration Cmax at which the maximum persistence time was observed, was found to be independent of the bubble size. It decreased uniformly as the carbon number increased, and was well correlated by the function y1/2 (dy /dc) -2 I dc)-2 . There was no apparent correlation with the surface excess at maximum persistence time.

Jan 1, 2006

By R. E. Whitehead

"Alkali/alumina and MgO/alumina molar ratio plots graphically portray both chemical and mineralogical changes accompanying potassic, phyllic, argillic, chloritic, and alunitic alteration of quartz monzonites and granodiorites hosting porphyry (as well as lode and greisen) ore deposits. The molar ratio plots can be used to identify different types of alteration. In most cases, the identification based on molar ratios coincides with petrographic data. In those instances where the molar ratio and petrographic identifications do not agree, the mineralogy might need to be re-examined. Hydrothermal alteration studies using trace elements could benefit from the application of complementary alkali/alumina molar ratio plots.Le diagramme des rapports molaires alkali/alumine et MgO/alumine illustre clairement les changements chimiques et minéralogiques qui accompagnent les altérations potassique, phyllique, argillique, chloritique, and alunitique des monzonites à quartz et des granodiorites encaissant les gîtes de type porphyrique, ainsi que des veines et des greisens qui leur sont associés. Les diagrammes de rapports molaires peuvent être utilisés pour identifier divers types d’altération. Dans la plupart des cas, l’identification basée sur les rapports molaires est en accord avec celle basée sur les données pétrographiques. Là ou il y a désaccord entre les rapports molaires et les données pétro-graphiques, il peut être nécessaire de réexaminer la minéralogie. Les études de l’altération hydro-thermale accompagnées d’une étude des éléments traces auraient avantage à utiliser un diagramme des rapports molaires alkali/alumine."

Jan 1, 2009