Search Documents

By R. M. Porter

PILLAR extraction at the Sullivan Mine bas been in progress for over twenty-five years and bas .involved progressively larger pillars. The largest pillar blasted to date exceeds one million tons and is described in this paper. This blast is believed to be one of the largest to take place entirely under-ground. The Sullivan Mine, owned by The Consolidated Mining and Smelting Company of Canada Limited, is located in the southeastern corner of British Columbia on the east flank of the Purcell range overlooking the twenty-mile wide Rocky Mountain Trench (Figure 1). The orebody is a bedded replacement deposit in argillites, varying in thickness up to 300 feet, but averaging about 80 feet. Above the 3900 Level, the dip varies from nearly horizontal to 40 degrees; be-low the 3900 Level it varies from 45 to 20 degrees (Figure 2). Pillar extraction follows a plan of retreating outward from caved areas. The size of each blast is determined by the effect which the removal of support

Jan 1, 1961

By Jean-Sébastien Kroll-Rabotin, Éric Climent, Florent Bourgeois

"Falcon concentrators are enhanced gravity separators designed for concentrating fine and ultrafine slurries. The Falcon UF model is unique in that it is dedicated to beneficiation of ultrafines, one key feature being that it does not make use of any fluidisation water. In a former study, we investigated the physical mechanisms that govern the transport of ultrafine particles (in the range 10 to 80 µm) inside Falcon UF concentrators, and concluded that separation efficiency is governed by differential settling. Initially, we derived and published a predictive model of the partition function under dilute conditions. The present paper proposes an extension of the initial model to concentrated ultrafine suspensions for application to industrial scenarios. The paper discusses how hindered settling has been added into the initial model to account for solid concentration effects. The modified model is tested against experiments carried out with a laboratory scale UF Falcon concentrator from dilute conditions up to 30 vol%. A good agreement between measurements and model predictions is obtained, which confirms that our hypotheses about the physics of separation inside a UF Falcon separator remain valid even at high concentrations.INTRODUCTIONThe Falcon concentrator is a fast spinning bowl that is fed at its centre of rotation. It uses centrifugal force to separate particles that are transported inside a thin liquid film that flows upward along the inclined wall of the bowl (McAlister and Armstrong, 1998). Due to differential settling, dense and coarse particles are concentrated inside the bowl whereas light and fine particles are rejected with the overflow stream. The fast rotation speed of the bowl yields high centrifugal force several hundred times the attraction of Earth. Despite the thinness of the liquid film (between 100 µm and 1 mm with a Falcon L40) where separation takes place, the Falcon concentrator can treat high flowrates (up to 30 L/min). At the bottom of the bowl, an impeller transmits the bowl rotation to the feed, which drains upward by centrifugal force as soon as it hits the base of the spinning bowl (Figure 1)."

Jan 1, 2011

By Franc R. Joubin

"Gold has been found in many parts of the Bridge River district of British Columbia; but it is from a relatively small area in the valley of Cadwallader creek that most production has come. The ore-bearing area measures 1/2 mile in width by 3 miles in length; and for convenience it is called the Cadwallader gold belt in this paper. In this belt are found the Bralorne and Pioneer mines and in addition several prospects under development.The gold of the Cadwallader gold belt occurs in quartz veins averaging about 3 feet in width and containing about ½ oz. of gold a ton. Except for a relatively small amount of silver, no other metals are produced from these veins. The ore-bearing veins occur in a variety of rocks. They occupy reverse faults and tension fractures belonging to a distinctive fracture system. Some of these structures are ore-bearing over lengths exceeding 5,000 feet and depths exceeding 3,700 feet. The production of the Bralorne mine (1932-1945) is 996,383 oz. gold and 190,709 oz. silver; that of the Pioneer mine (1930-1945) is 777,588 oz. gold and 135,698 oz. silver. These two mines have together distributed about $25,000,000 in dividends.The Bridge River district first attracted attention in 1863* when prospectors were attracted by its small but rich placer gold deposits. Most of the important lode deposits of the Cadwallader gold belt were discovered in 1897 (11). Many years of desultory development followed and it was not until 1928 and 1932 that the Pioneer and Bralorne mines, respectivdy, entered into profitable production."

Jan 1, 1954

By Roberto Busato Belger

- Fertilizer Business Overview - Supply -Demand Balance in the World - Supply -Demand Balance in Brazil - Brazilian Market Growth Opportunities - Fosfertil Operations - Fosfertil Expansion Plan - Salitre Project - Project Characteristics - Technical Challenges and Solutions - Technical Support Studies Conclusions

May 1, 2010

By E. Sharifi

Advanced Process Control (APC) has been one of the most beneficial tools in the past decades available to minerals processing industry. Low capital cost together with significant improvements in process optimization have made APC an attractive investment option for nearly all mineral processing units. During economic downturns, importance of process optimization becomes even more relevant as metal producers tend to target de-bottlenecking and process efficiency improvements rather than large-scale capacity upgrades. APC project clearly has a lot of potential to improve process performance but there are also some pitfalls to be identified and avoided in order to achieve a desired outcome. Above all, APC project implementation is collaboration between the system vendor and user. Targets for the optimization must be agreed together with the customer and process performance must be defined before and after the optimization project. Most importantly, performance of the process must be monitored on a continuous basis during and after the project and potentially improved further. This paper discusses Outotec’s experiences from various concentrator optimization projects. Some examples are discussed in more details; however, the main target is to present general guidelines enabling a successful APC project implementation.

Jan 1, 2014

By R. Gutray, J. E. Grainger

This paper deals with the use of a cement-deslimed mill tailings mixture for a scraping floor in cut-and-fill stopes at Madsen Red Lake Gold Mines Limited. It describes the mixing and placing procedures and the precautions used with respect to the floor while mining in the stopes. Details of the mix are presented, and advantages and disadvantages discussed. The paper concludes with a brief outline of the costs.

Jan 1, 1966

By Noel W. Kirshenbaum

Difficulties and costs of transport markedly affect Canadian mineral producers because of distance from markets, weather conditions and rugged terrain. The chemical and physical nature of sulphide concentrates presents additional difficulties in handling and transport, resulting in higher costs which are ultimately borne by the mineowner. Troublesome properties include the thixo-tropic character of wet concentrates, freezing, susceptibility to autogenous heating, and fine particle size causing spillage and dusting losses. Canadian mineowners and shippers must contend with these problems and with stringent regulations governing the maritime shipping of concentrates. A "systems approach," in which complementary techniques in materials preparation, handling and transport are integrated, could reduce freight costs and losses for those selling concentrates, facilitate operations for those carrying and handling them and, in some cases, improve metallurgical processes in smelters receiving them.

Jan 1, 1969

By J. Oré

An alternative method for dewatering slurry (tailings) is the use of geocontainers (MacTubes). The practical application of this work was carried out in the concentrator plant of the Raura Mining Company, located in the occidental mountain between Huánuco and Lima in Peru?s central highland. For the development of the research, the MATLAB R2012a software MGeST (v. 1.0) was used (Slurry Geocontainer Maccaferri Treatment). MGeST is used for sizing MacTubes, which allows determination of the most important design parameters, such as height (H), filling residual pressure (P1O ), strength of geosynthetic (T), and dehydration height. Compared with GeoCoPS v. 3.0, there is a maximum difference of 3% between the results obtained. The tailing to be treated in the MacTube have a specific weight of 11.62 kN/m3. After several tests it was determined that a MacTube of an apparent opening size of 0.22 mm was required for this specific weight.

Aug 1, 2013

By Todd Smith, Brigitte Lacouture, Greg Anderson, David Lin

"The lead and zinc flotation circuits at Red Dog Mine are preceded by a preflotation circuit which recovers naturally-floating organic carbon contained in the ore. Organic carbon is a potential contaminant in the lead concentrate and is detrimental to lead-zinc selectivity. Prior to 2007, the Red Dog preflotation circuit consisted of a single stage bank of tank cells which floated the organic carbon. The preflotation concentrate was discarded directly to tailings, however, this stream contained significant amounts of lead and zinc. Zinc loss to preflotation ranged from 2% to 6%, relative to the zinc in the mill feed and was proportional to the amount of organic carbon in the ore. The main mechanism of the zinc loss was entrainment.Pilot plant and modeling testwork were conducted to examine the use of a Jameson Cell to clean the preflotation concentrate. Results indicated that up to 90% of the zinc deporting to preflotation concentrate could be returned to the flotation circuit for recovery. The installation of a 5.4 m Ø Jameson Cell with 18 downcomers was initiated in June 2006. The new preflotation cleaning circuit was commissioned in March 2007. Conservatively, preflotation cleaning has resulted in zinc and lead absolute recovery gains of 1.0% and 1.5%, respectively. The $9.1M project has a payback period of approximately 1 year at current metal prices.INTRODUCTIONRed Dog Preflotation CircuitRed Dog Mine is located above the Arctic Circle in northwest Alaska. It is the world’s largest zinc concentrate producer with a production rate of more than 1.0M t/yr. Red Dog is operated by Teck Cominco Alaska Incorporated under an operating agreement with the Northwest Alaska Native Association (NANA). Due to the remote location of the mine, it is accessible only by air, or seasonally, by ocean-going barges.The Red Dog deposit is a rich sedimentary exhalative (sedex) zinc-lead-silver deposit. The major sulphides, in decreasing order of abundance, are sphalerite, pyrite, galena and marcasite. Due to the complex nature of the ore body, run-of-mine ore is blended in stockpiles before being crushed and processed through the concentrator. The average mill feed grade for 2006 was 6.1% lead, 20.6% zinc, 8.0% iron and 0.67 % organic carbon."

Jan 1, 2008

By Marcel Vallée

Abstract -Traditionally, samples collected for mineral deposit evaluation have been viewed without explicit reference to reliability, with the illusion that a true value is attainable from a few samples and verifications. For exploration, mineral deposit estimation and production quality control the following definition is proposed: "a sample is a small quantity of material relative to the geological mass it represents, collected according to a systematic procedure, of measurable reliability, from which the grade/quality of the mass which it represents may be estimated, based upon appropriate protocols. This paper will concentrate on the actual rock sampling process. Too often, sample size has been, and is still viewed as a matter of convenience, leaving out representivity considerations, despite the importance of samples on project estimation. Linear samples (chips, channels, drill), panel samples, broken rock or mining samples and very large samples are considered. Collection procedures and quality control protocols to improve the representivity of non-mechanical samples are proposed.

Jan 1, 1998

By R. W. Schutz

"Titanium possesses an exceptional and wide-range resistance to chlorides and their compounds when compared to most corrosion-resistant engineering alloys (CRAs) used in the chemical process industry. This natural resistance to chlorides stems from titanium’s protective, tenacious, and readily rehealable titanium oxide surface film, which is chemically stable over a wide range of pH and redox potentials in aqueous environments. This passive film explains titanium’s elevated resistance to anodic pitting, crevice and stress corrosion, and erosion-corrosion in aqueous chloride environments.Guidelines for successful selection and application of industrial titanium alloys are derived from an extensive laboratory test database and more than forty years of industrial/chemical service experience. These guidelines are simplified, and alloy corrosion performance is assessed with respect to four basic aqueous chloride service categories where selection or consideration of titanium is highly merited. An overview of historical titanium alloy applications in chloride-rich environments in a wide variety of process industries substantiates their exceptional chloride tolerance. These industrial titanium alloys are cost-competitive with stainless steels and nickel alloys, readily commercially available, and routinely fabricated and welded in the shop and field via well-established methods."

Jan 1, 2002

By Jeffrey L. Pagnutti

Train derailment can lead to loss of capital, damage to the environment, and loss of life. Machinery condition monitoring techniques can be used to develop a structural health monitoring system for railway track to detect faults at the incipient stage, before catastrophic failure occurs. This study uses vibration measurements from a novel material haulage unit to develop a decision support system for railway track maintenance. A variety of feature sets and classifiers were compared to determine the optimal configuration for fault detection. The results highlight the shortcomings and advantages of certain methods and describe the process in which the optimal result was obtained. The Parzen data descriptor paired with a refined statistical feature set performed the task of fault detection with less than five percent false positive and false negative classification error. Overall, the outcome of these experiments indicated that condition monitoring of railway systems is a promising approach for fault detection and has the potential to avoid catastrophic failure.

May 1, 2013

By L. P. Srivastava

Rock bolts have been used since long to enhance the shear strength response of jointed rocks in civil and mining engineering structures. However, the assessment of strength response of a rock mass reinforced with rock bolts remains an unresolved problem till date. In the present article, an attempt has been made to study, through physical model tests, the shear strength enhancement of a blocky mass due to provision of passive rock bolts. Direct shear tests were conducted on large specimens of size 750 mm x 750 mm x 900 mm of rock mass under a normal stress varying from 0 to 2.0 MPa. Concrete was used as a model material to simulate intact rock and, elemental blocks of size 150 mm x 150 mm x 150 mm were used to form the mass specimens. Steel bolts of 6 mm diameter with 2 mm thick grout were used to reinforce the mass. Three different configurations of bolts were adopted. Observations were made on shear stress, horizontal shear displacement, and dilation during the tests. Effect of normal stress and reinforcement on peak shear stress and shear stiffness was studied. It is observed that the rock bolts enhance the shear strength of the mass by preventing sliding along the shearing plane, and by inducing additional normal stress due to tension mobilized in the bolts. The rock mass, therefore, becomes stronger due to the high degree of interlocking produced by the bolts. Shear strength of the mass increases with increasing numbers of bolts. In the case of reinforced mass, the enhancement in shear strength due to provision of bolts decreases with an increase in normal stress. The provision of bolts improves the cohesion of joints substantially. The effect on friction angle is low. The shear strength enhancement depends on the area of the bolts, spacing of the joints, spacing between the bolts and the cohesion of the intact material. A correlation has been established using which the enhancement in shear strength due to the provision of bolts can be assessed.

Jan 1, 2015

By Ahmad Ghahremaninezhad, Denver H. Cowan

Much of today’s gold is locked within sulphide minerals. These sulphide minerals, including pyrite, need to be subjected to oxidative pre-treatment in order to leach the refractory-gold using traditional methods. Typically autoclaves employing high temperatures between 180?225 ºC, and extremely high pressures between 1,500?3,200 kPa, are used for the oxidative pre-treatment. However, the autoclaves themselves are very expensive, costly to operate and maintain, and produce excess sulphuric acid. This paper studies the atmospheric oxidation of pyrite in ferric sulphate solutions. In general, pyrite oxidation under atmospheric pressure can result in high elemental sulphur production, i.e. less acid generation. Activated carbon has displayed an ability to catalyze the process, achieving reasonable kinetics. The reaction kinetics were investigated by altering acidity of the leaching solution, temperature, catalyst ratio, sparged oxygen and agitation. A combination of X-ray diffraction, scanning electron microscopy, optical microscopy, X-ray fluorescence, inductively coupled plasma mass spectrometry (ICP-MS), and atomic absorption spectroscopy (AAS) were used to monitor the kinetics of the process and elemental sulphur yield. The purpose of this investigation was to determine optimal operating conditions that maximized kinetics of the atmospheric oxidation while maximizing elemental sulphur yield.

Jan 1, 2015

By D. J. MacKinnon

"The Canadian Copper Company, formed in 1885, began mining the nickel-copper ores of Sudbury in 1887 and producing nickel-copper matte from its smelter in 1888(1). Although it was quickly appreciated that the separation of nickel and copper (i.e. refining) was critical to the production of a marketable nickel product, refined nickel was not produced in Canada until about 1918. From the beginning of the industry, there was considerable political agitation to refine nickel in the Province of Ontario(2). The companies, however, claimed that the existing processes, viz. the sodium sulphide ""tops and bottoms"" process operated by the Orford Copper Company of New Jersey, U.S.A.(1,3,4) and the carbonyl process(5,6) developed by the Mond Company at Clydach, Wales, were too costly to operate in Canada. Nickel was first refined in Ontario about 1918 when the International Nickel Company opened a nickel refinery at Port Colborne, Ontario(6). Initially, however, the refinery at Port Colborne employed the Orford sodium sulphide process, and the first electrorefined nickel in Canada was produced in 1920 by the British America Nickel Corporation whose mine and smelter were located in Sudbury, Ontario, but whose electrorefinery was located at Deschenes, Quebec, near Ottawa, Ontario. The purpose of this article is to outline the early history of nickel electrorefining and to trace the significant developments which led to the first successful commercial electrolytic nickel refinery in Canada. The development of an electrolytic process for refining nickel is due largely to the efforts of four individuals, viz. Carl Hoepfner, Hans A. Frasch, D.H. Browne and ultimately N.V. Hybinette, and the contribution of each is discussed separately below."

Jan 1, 1999

By D. Verhulst

The Altair process digests ilmenite concentrate in high-chloride HC1 solution, with complete dissolution of titanium and iron. The Fe(III) ions are reduced to the ferrous form, and the solution is cooled to produce crystalline ferrous chloride. Titanium is transferred by solvent extraction into a purified, concentrated Ti stream, which is spray-hydrolyzed to produce TiO2 hydrate. The hydrate is further calcined with additives to generate a high-quality pigment. All the chloride streams are recycled. In the original flowsheet, the iron chloride is pyrohydrolyzed by spray roasting to regenerate 18% HCl, which is subsequently converted to HC1 gas and water by pressure-swing distillation. A modified flowsheet includes an alternative to iron chloride spray roasting, producing more concentrated HCl and decreasing the amount of solution to be distilled. Improvements in digestion, solvent extraction and final pigment production are also introduced. A 100 t/y pilot plant is being built and will test the new concepts and confirm the overall water, acid and impurity balances of the process.

Jan 1, 2006

By T. Alan O'Hara

"Annual mining revenue can be computed by formulae relating metal prices, smelting schedules, concentrate grade and recovery to known ore grade and an assessment of core samples. Operating costs at different daily tonnages are related to orebody shape, mining method, milling process and general plant services. Capital costs are related to sizing of mining equipment, mine development, plant-site topography, climate and accessibility, plant services and personnel housing. IntroductionA crude guide to the average 1978 cost of mine projects is shown in Figure 1, but the costs of many mine projects have differed widely from the graphed average costs of $800,000 T0.6 for underground mine/mill projects and $400,000 T 0.6 for low-grade open-pit mine/mill projects.High mine project costs and high operating costs are characteristic of open-pit mines with high stripping ratios, underground mines with thin orebodies, mills with complex metallurgy, and projects located in isolated regions with severe climate, mountainous topography, and lacking access to existing roads, towns and electric power. When none of these adverse conditions prevailed, the mine project cost was typically much less than the graphed average cost. Virtually all the conditions likely to cause high capital and operating costs are known from knowledge of the local topography, climate or accessibility, or can be assessed by tests on core samples, as soon as the orebody has been outlined by drilling .A more accurate estimate of over-all project capital cost and operating cost can be made from a summation of items of cost after judging the effect of specific local conditions on each item of capital and operating cost. This paper offers guides in judging the effect of local conditions on the sizing and 1978 cost of specific items of capital cost and operating cost and operating cost of mine projects. When the specific items of capital cost and operating cost are totaled and measured against expected net revenue and taxes over the life of the mine using the net-present-value or discount-cash-flow methods, the result should show whether the mine project development is clearly feasible, doubtfully feasible or clearly uneconomic. If the development of the mine project is clearly feasible, or probably feasible, a detailed feasibility study by experienced consulting engineers should be commissioned before any financial commitments are made; but if project development appears to be uneconomic, the time and cost of a detailed feasibility study is not warranted."

Jan 1, 1980

By E. O. Reinbold, J. H. Johnson, D. E. Keski-Hynnila

A field laboratory for use in monitoring underground mine air quality has been developed and proven in underground service. The laboratory includes two separate monitoring systems and data analysis computer programs. One is the Mine Air Monitoring Laboratory (MAML). This is an enclosed trailer-mounted laboratory capable of monitoring CO2, CO, NO, NO2 particulate matter, S02, NH3, temperature and air velocity in the mine drift. The MAML can be up to 1000 feet away from the area being monitored. The second system is the vehicle data system, mounted on the load-haul-dump (LHD) vehicle, which monitors engine speed, engine fuel rack position, exhaust gas temperature, ambient temperature, vehicle speed, CO2 concentration near the operators' breathing zone and the mode of operation of the vehicle. The two computer data analysis programs and the two field instrument systems comprise a complete Mine Air Quality Laboratory (MAQL) for underground pollutant studies. Data from the systems have been used for studying vehicle duty cycles, ventilation systems, exhaust after-treatment devices, vehicle exhaust system design and portable instrumentation. Descriptions of the laboratory are presented along with a summary of some of the experiments performed. The capabilities of the lab are discussed, along with future potential uses.

Jan 1, 1981

By Magdy Ibrahim

This paper presents experimental design and development of a low-cost remote sensing hardware designed to support automated site data acquisition for near real-time progress reporting of construction operations. The developed hardware utilizes open source microcontroller equipped with multiple sensors that include 3D accelerometer, GPS, Data logger and Bluetooth. The use of open source microcontroller makes the developed design cost effective; freeing it from the need for costly license fees. Its platform configuration is flexible; enabling the addition of temperature, weight and other sensors, Wi-Fi and Xbee capabilities to suit individual field applications. Pilot tests have been carried out in laboratory and outdoor environments. The results prove effectiveness and robustness of the developed configuration. The paper provides description of the individual components used in the development of this prototype hardware. It also describes the technical characteristics, capabilities and limitations of the developed hardware. The findings of comparison with alternative technologies used for outdoor tracking of construction operations are presented. The comparison is carried out with respect to range, cost and suitability for outdoor environment. The developed hardware is expected to support a wide range of applications including tracking of earthmoving operations, highway construction and onsite resources. As well, it is expected to enhance safety on construction jobsites.

Aug 1, 2013

By Farzad Mohammadi, Patrick Littlejohn, David Sanguinetti

Arsenic levels in metal concentrates are increasing as mining companies turn to developing low grade and complex ores. When arsenic bearing minerals are smelted, arsenic deports as gases which must be neutralized by a scrubber system. The resulting scrubber effluent is high in dissolved arsenic and requires treatment before the wastewater can be discharged or re-used. Conventional arsenic removal relies on lime addition followed by calcium arsenate formation and precipitation as hydroxides. As an alternative, arsenic removal with sulphide precipitation is receiving more attention due to potential advantages of the technology. Process streams high in arsenic often contain concentrations of dissolved metals that may be selectively recovered during sulphidization, producing a product that can be reprocessed and reducing waste generation. This paper will review laboratory testing completed for arsenic removal through sulphide addition and precipitation of arsenic (III) sulphide in combination with metals recovery to offset arsenic removal costs.

Jan 1, 2014