Search Documents

By E. Asselin, P. Sauve, H. Salomon-de-Friedberg

"Residues from the CESL Copper process were leached using the CESL Gold process. The kinetics of reaction were confirmed to be fast with over 50% of the gold consistently extracted within 2 minutes of leaching. Final gold extractions under the conditions tested here were between 80-90% obtained within 90 minutes. A model for the CESL Gold process was developed. This model is slightly different based on whether the copper concentrate leach residue was ground or unground prior to leaching: the gold leaching rate constant is approximately twice as fast for the ground samples. Unground residues had a P80 of 13 ?m whereas ground residues had a P80 of 10 ?m. The model predicts a 43% decrease in leaching time for ground residue versus unground residue to achieve the same extraction under otherwise identical conditions. The model was more accurate for the ground samples. INTRODUCTIONTeck's CESL Process (Jones, 1996) was developed to provide an economically attractive alternative to traditional copper smelting. It has since evolved to also deal with copper concentrates containing valuable impurities such as nickel and undesirable ones, such as arsenic, while reducing downstream costs. Effective recovery of gold and silver is essential to the economics of the CESL Process. The Brook Hunt 2007 copper concentrate assay data (Wood-Mackenzie, 2007) were examined to determine the ratio of gold plus silver value relative to the contained copper. As indicated in Figure 1 below, nearly two-thirds of concentrates have 10% or more of their total value tied up in their precious metals content.CESL has extensively examined the recovery of gold and silver at bench, pilot and demonstration scale, which has culminated in the present CESL Gold Process (Barr et al., 2007). The process targets the precious metal contained in the leach residues produced in the copper portion of the flowsheet. This residue has two primary components which influence downstream processing. The major iron-rich fraction (-75 wt%) of the residue is a mixture of various forms of iron oxide precipitates including hematite and jarosite (Sahu and Asselin, 2011). The iron fraction ranges from amorphous to crystalline in nature depending on the compound precipitated, upstream operating conditions and feed material composition. The lesser, but by no means less important, fraction is a mixture of elemental sulphur and unreacted sulphides (principally pyrite).Elemental sulphur formed during the oxidative leach of the copper concentrate reacts with cyanide to form thiocyanate (SCN-) making a traditional cyanide leach approach too costly. Since the SCN formation reaction strongly depends on contact time with the CESL residues (Po, 2007) short contact times were preferred. This factor guided the development work towards the eventual room temperature, pressure cyanidation process which results in near complete gold dissolution in 90 minutes. A recent CESL gold demonstration campaign treating 1.5 t/d of residue from the copper oxidation step achieved an average gold extraction of 91% (96% maximum)."

Jan 1, 2012

By Kevin M. Ansdell, Irvine R. Annesley, Christine L. Mckechnie

The U-Th-REE mineralization at Fraser Lakes Zone B is hosted by granitic pegmatites and leucogranites, which lie along the deformed contact between Paleoproterozoic metasedimentary gneiss of the Wollaston Group and Archean orthogneiss, approximately 25 km from the southeastern edge of the Athabasca Basin. The pegmatites/leucogranites are subcordant to concordant with the regional foliation and are concentrated within a northeast-plunging antiformal fold nose, the study area, which lies west of Fraser Lakes. The mineralized pegmatites/leucogranites in the western part of the study area (Group A) are typically enriched in U (± Th) with Th/U ~1, and contain uraninite, thorite, zircon, and allanite. Those intruding the central part of the study area (Group B) are generally enriched in Th and LREE, with Th/U >2, and contain monazite, thorite (commonly U-enriched), and zircon. The pegmatites and leucogranites in Group A tend to be slightly enriched in SiO2 and depleted in TiO2 relative to those in Group B and are interpreted to represent more evolved crustal melts. Both groups are peraluminous and show varied chemistry. Partial melting (~850ºC and 9 kbar) of a metasedimentary rock-dominated source, entrainment of accessory minerals as xenocrysts, and assimilation-fractional crystallization processes combined to enrich the granitic pegmatites/leucogranites in U, Th, and REE elements. Transfer of melt from the source region to the crystallization sites was assisted by deformation within and along major structural zones, such as the folded Archean-Paleoproterozoic discontinuity. The character of mineralization and structural control in the study area is reminiscent of the alaskite-hosted deposits at Rössing, Namibia.

Jan 1, 2013

"Here, we statistically proved that giant earthquakes occur at lunar phases specific to each subduction zone. Enough attention during the lunar period, especially when seismicity is occurring, will significantly reduce damage from giant earthquakes. Two case studies in which giant earthquakes occurred after seismicity in dangerous lunar phases were discussed, and the mechanisms underlying why giant earthquakes occur around neap tide at some subduction zones were explained by prohibition of giant earthquake occurrences due to high strain rates at spring tides at N–S subduction zones. The prohibition was statistically proven for uniaxial creep tests on Inada granite with slight stress disturbances. INTRODUCTIONIn previous studies, we showed that from 1900 to present, giant earthquakes (MW ??8) have occurred at lunar phases specific to each subduction zone (Fujii & Ozaki, 2012; Ozaki & Fujii, 2012). Although we later proposed a possible reason for these occurrences, the study lacked statistical analyses (Fujii et al., 2013). Therefore, this paper shows the results of such statistical testing and presents case studies for the Tohoku 2011 and Chile 2014 events, thereby providing updated data on giant earthquakes through July 2014."

Jan 1, 2015

By J. A. Cox, R. S. Mattson

"One of the main problems encountered in employing sublevel caving is the inherent high dilution factor. The operating results at Granduc illustrate that this dilution can be closely controlled and satisfactory recoveries achieved, in base metal ores grading less than 2.0% copper equivalent, by using an assay grade control system based on the fundamental draw characteristics. The history of draw control procedures employed since the start of operations provides an effective comparison between this system and one based mainly on tonnage. The transverse and longitudinal sublevel caving mining methods are described and it is shown how improvements in design layout, operating practice and draw control in narrow complex ore zones (12-foot minimum width) have raised the operating performance of the longitudinal system to a satisfactory level."

Jan 1, 1973

By Malcolm Black

Introduction The circumstances under which the gold mining industry was forced to curtail operations a few years ago are well known to all. The effect of those circumstances is particularly noticeable when one enters some of the larger mills that were designed, in better times, to treat relatively large tonnages. On their grinding floors one will observe that a number of grinding units are lying idle, and the ravages of rust are everywhere in evidence. The same applies to other equipment throughout these mills. In 1941, we found it necessary to reduce tonnage considerably in the Wright-Hargreaves mill. With the assumption that a lower tonnage would be of long duration, we began to focus our attention on some of the idle equipment with a view to re-arrangement of the flow-sheet for greater economy of operation. In an article by the writer published in the Engineering and Mining Journal (March, April, and May issues, 1939) , it was pointed out that in designing this mill there was a very limited floor space available. The choice of thickening equipment was imposed solely by the necessity for space: conservation. Thickening by gravity would have required 5,000 square feet of floor space, whereas Genter thickeners required only 1,200 square feet. As a consequence, the Genters were chosen. The decision to add flotation to the circuit was made primarily to save space. On a cost-plus-tail basis, 80 to 100 hours agitation on all pulp would produce similar overall results, but would require much more space.

Jan 1, 1948

By Jim Robertson

Summary of Presentation ??What is the GARD Guide ??The Need for a GARD Guide ??Mining Industry?s Commitment to Solving ARD Problems ??The Ultimate Solution ?You ??The GARD Guide ?Scope ??The GARD Guide ?Structure ??Wiki Demonstration

May 1, 2009

By L. López

Argentina reported about 40,000 tonnes of uranium (tU) as reasonably assured resources and inferred resources for the production cost category <130 US$/kgU in the OECD-NEA/IAEA classification scheme. These resources belong to the following projects: Sierra Pintada, Cerro Solo, Don Otto, Laguna Colorada, Laguna Salada, Meseta Central and Amarillo Grande. With three heavy water reactors in operation and an approximate installed capacity of 1.7 GWe, the current natural uranium requirements are about 220–250 tU per year. Based on various nuclear growth scenarios, it is estimated that by 2030 there will be a generation capacity of some 3,092 GWe for the reference case, with raw material needs of some 486 tU per year. Currently, there are no perspectives for local uranium production in the short term, and it is thought that uranium projects with identified resources must complete resource delineation and advance in technical pre-feasibility studies for the recovery of uranium. It is expected that Argentina continue meeting the uranium demand with imports in the next following years. In the Latin America region, both Brazil and Paraguay could be considered as potential uranium suppliers. In conclusion, despite the apparent growth prospects for the use of nuclear energy to generate electricity in Argentina, there are no immediate prospects for the provision of uranium oxide concentrates from domestic deposits for fuel fabrication. This has implications for supply and energy security.

Jan 1, 2020

By K. Scalise, M. Teixeira, K. C. Kocsis, J. Parrish

"This paper aims to introduce and discuss a newly developed algorithm, which can be uploaded on smart watches and other mobile devices to inform and protect underground personnel working in hot and humid environments. Using this algorithm, the metabolic rate (M) of a worker can be determined in “real-time”. In addition, besides warning signs and alarm signals emitted by the smart watch, the algorithm has the ability to determine work-rest time periods based on the worker’s physiological parameters (e.g. age, height, weight, gender) and the climatic parameters (Td, Tw, flow velocity). This paper also investigates whether a re-designed auxiliary ventilation system can provide appropriate work conditions in the production stopes. INTRODUCTION An underground environment with high temperature and humidity conditions generated from various heat and moisture sources can significantly affect the thermoregulation processes of the human body. This can lead to heat-related illnesses such as heat rash, heat cramps, heat exhaustion, and heat stroke. Heat stroke is a serious illness that carries a high risk of fatality, if the underground workers are not immediately treated and the climatic conditions are not corrected (McPherson, 1993). There are two methods used to control the climatic conditions in underground mines: (1) Using ventilation and cooling systems to reduce the thermal stress on the mine workers, and (2) Reducing the heat transferred to the ventilating air from major sources such as: strata, auto-compression, mining equipment, groundwater, blasting, etc. The heat from strata and auto-compression is transferred to the ventilating air at varying degrees, based on factors such as the virgin rock temperature (VRT), the thermal properties of the surrounding rock formations, and the surface air temperature. However, the use of mining equipment and blasting processes can be managed to reduce their contribution to the mines’ overall heat load. To provide appropriate work conditions, selecting the most suitable cooling method depends on the level of heat to be removed, the location of the problem areas, and economic constraints (Brake & Bates, 2002; McPherson, 1993). Because every mine is unique, it is essential to monitor the climatic conditions to select the most appropriate method of cooling. A majority of the time, simply adjusting or re-designing the auxiliary ventilation system can efficiently remove the heat and dilute the contaminants. This may involve moving the ducting system, changing the size of the duct, changing the size of the auxiliary fan, or switching from forcing to an exhausting fan arrangement. If the required air volumes are higher than the existing primary ventilation system can supply, other measures may need to be taken to increase the airflow delivery. This may include regulating the flow in some areas of the mine to increase airflow to the desired area, adding booster fans, or replacing the primary fans."

Jan 1, 2019

By Joseph Daniels

When Dame Nature shook her horn of plenty and distributed her bounties over the face of the earth, she blessed the Pacific coast with many riches, but with these she added many offsetting disadvantages or handicaps, designed, no doubt, to effect a proper balance between wealth and economy. Nowhere is the application of the law of compensation more aptly illustrated than in the matter of fuel and power resources. A glance at the map of the Pacific northwest will show that west of the Coast Range batholith we are bounteously supplied with coal, with timber, with water power, and with tributary resources of oil from California. Alaska, British Columbia, Washington, all contain large resources of coal; Oregon and California to a lesser degree, but, compensating the golden state for its deficiency in this respect, oil was placed in the treasure ,chest. Timber, of wide variety and in lavish quantity, covers the forests from tidewater to mountain slope, and within this protected watershed area flow streams which give the Pacific coast states the largest single share of the potential water-power resources of the country. Something over 40 per cent. of the total estimated horsepower of the United States is to be found in the Pacific states, and British Columbia has 15 per cent. of the total for Canada; but of this total less than 10 per cent. has been developed.

Jan 1, 1924

By G. A. Davidson, P. G. Williams

"New developments in centrifugal slurry pump technology are discussed in relation to their importance for improving pump operation and reliability.Experimental data obtained by measuring the velocity of liquid flows in a slurry pump casing using Laser Doppler Velocimetry are presented. This demonstrates the importance of selecting pumps with the proper hydraulic design to provide optimum efficiency, maximum part life and minimum operating cost.The paper also discusses the use of new wear resistant materials, such as ceramic/metal composites, which can significantly improve the life of parts exposed to abrasive media. The results of laboratory attrition tests are presented. IntroductionCentrifugal slurry pumps are of primary importance for the hydro transport of abrasive and corrosive media in the mineral processing industry. As for all process equipment, slurry pumps must be carefully selected and operated to provide optimal performance. To achieve this, it is necessary to select equipment which will provide efficient and reliable operation for the specific service conditions and incorporates the best materials available to obtain maximum parts life.Abrasive wear of liquid end components is the most important aspect that distinguishes the design and application of slurry pumps from other types of pumps. It is therefore necessary to have a fundamental understanding of the mechanical interaction between pump components and the media being handled, as this will impact significantly on hydraulic design, mechanical reliability and selection of wear resistant materials. Recent advances in computational approaches&apos;» have greatly improved the prediction of wear rates in pump casings by facilitating the solution of complex equations which describe the wear mechanisms mathematically. In conjunction with this, new experimental techniques allow researchers to measure flow fields in pump casings using non-invasive devices such as Laser Doppler velocimeters."

Jan 1, 1992

By Nancy C. Mohn

?Even though the age of many existing coal units exceeds 30 years, these units continue to perform with excellent reliability and at a competitive cost with other fossil fuel units. ?NERC data shows a consistent increase in availability for all utility coal generation ?With the opening of power markets, the challenge for coal is to produce competitive electricity while meeting increasingly stringent, and costly environmental limits. ?During the 60s and 70s, subcritical steam power plants dominated the market. The emphasis was on scale-up to larger MW size units. ?In the last decade, we have seen interest in a broader set of technologies with new drivers: ?Fluidized bed technology was developed to respond to increased environmental requirements, particularly with lower quality fuels ?Supercritical pressure units have gained interest for both fuel cost savings and reduced emissions due to higher efficiency.

May 1, 2001

By Frank Otten, Jochen Greinacher

"In July 2017, Deilmann-Haniel signed a contract with IOO Slavkaliy to sink two 750 metre (m) deep freeze shafts for the Nezhinsky Potash mine in Belarus. This is the second shaft project where this technology is employed after two over 1,000 m deep shafts for a potash project in Saskatchewan, Canada, have been sunk by the application of the Herrenknecht Shaft Boring Roadheader (SBR) technology. Developed to sink shafts for green field projects in soft to medium hard rock, in frozen or unfrozen geology, the machine technology utilizes a roadheader-type cutterhead on a telescopic boom to mechanically excavate the rock, and a pneumatic mucking system to convey the muck from the face into the buckets. This leads to a manless face during the sinking cycle and thus a significant improvement in terms of workplace safety. For the Nezhinsky project, the SBR design was significantly modified in close cooperation between Deilmann-Haniel and Herrenknecht, based on the available experience and the special requirements of the project. Such modifications have been for example the adaptation of the Pneumatic Mucking System to cope with wet material as well as dry as originally planned or the shaft lining moving from shotcrete application to jump for and tubbing installation for which a step-change hands-off tubbing erector for the placement of segments was designed. Further modifications to optimize the machine technology for the requirements during shaft sinking were applied on the two machines for the Slavkaliy project as well as several revisions to match the special project requirements. The SBR is suitable for soft and medium hard rock up to 100 MPa UCS. The main design limits are maximum weight of the machine with 400 tonnes and length or height of 50 m due to the depth of the pre-sink. The Pneumatic Mucking System was changed in all components, sheaves and rope arrangement were redesigned and the concept of the hoist system was also re-engineered. The SBR in Belarus is configured for a daily sinking rate of three metres and all systems behind the cutting boom are not the bottle neck of the whole system. The works on site started in November 2017 including freeze hole drilling, construction works, site setup, installation of hoists winches, permanent headgears and other components required for sinking. The SBRs arrived on site in June/July 2018 and were preassembled on surface and then lowered into the 50 m pre-sink. SBR #1 started full face sinking in mid-December 2018, and SBR #2 in late January 2019. By the end of February 2019, the machines were at 150 m and 100 m depth respectively, and achieved up to 3.6 m/day concrete lined shaft. The SBR and the sinking system, the experiences, problems, technical solutions and performances of this challenging project will be presented in this paper."

Jan 1, 2019

By J. D. Clucas, N. Verbaan, T. Grammatikopoulos, D. B. Dreisinger, C. Forstner, M. Aghamirian

"Search Minerals is currently exploring the Port Hope Simpson (PHS) Rare Earth Element District in southeastern Labrador, Canada. The Foxtrot Rare Earth Element (REE) Project in the PHS District has a 43-101 resource estimate consisting of 3,410,000 tonnes of Indicated Mineral Resources and 5,850,000 tonnes of Inferred Mineral Resources. The indicated and inferred resources contain 1.07% and 0.98% total rare earth element oxide (including yttrium), respectively. The dysprosium and neodymium grades are particularly attractive at 218 ppm Dy2O3 and 1687 ppm Nd2O3 for the indicated resources and 208 ppm Dy2O3 and 1494 ppm Nd2O3 for the inferred resources. The mineralization remains open along strike and at depth and is only one of a number of attractive exploration targets in the Port Hope Simpson area. The REE minerals fergusonite and allanite are present. The ore can be beneficiated by gravity, magnetic separation and flotation to a recovery of +80% for the individual REE. Acid bake and water leaching may be used to extract REE into solution for subsequent purification and recovery. The extraction range for single stage leach tests were 91-96% for Nd, 84-87% for Tm and 92-94 % for Dy with modest acid consumptions. INTRODUCTIONSearch Minerals Inc. (Search) is exploring the 100% owned Port Hope - Simpson District in Labrador, Canada for rare earth elements (REE). This District is approximately 135 km by 12 km in size, and is highly prospective for heavy and light rare earth elements. A total of 11 REE prospects have been discovered in the District to date, including the Foxtrot. In addition, Search is exploring in the 100% owned Henley Harbour region and has joint ventures with Quest Rare Minerals in the Strange Lake region, and with Great Western Minerals Group in the Red Wine complex, all in Labrador. These exploration locations are illustrated in the Figure 1. The focus of this paper is the investigation of the mineralogy and processing of Foxtrot REE materials. The Foxtrot resource falls within the claims held by Search in the Port Hope Simpson REE District. The infrastructure available at Foxtrot is excellent with a deep water port, air strip and road and power infrastructure at Port Hope Simpson. Over $7 Million has been spent to date on exploration and development of the District. The Foxtrot has been explored using prospecting geochemical methods, geophysics (airborne and ground), channel sampling of surface outcrops, mapping and three phases of drilling (18,934 m total)."

Jan 1, 2012

By Gae On Kim, Ki Baik Kim, Suk Hoon Kang, Tae Kyu Kim, Sanghoon Noh

"Advanced radiation resistant oxide dispersion strengthened steel (ARROS) is being developed as a fuel cladding tube material for future nuclear reactor system applications. The research activities consist of advanced radiation resistant ODS steel development and fabrication technology development of ODS steel structural components. One candidate material with a chemical composition of (in wt%) Fe-10Cr-1Mo-0.5Mn-0.1V-0.25Ti-0.35Y2O3and was selected as representative materials, and this material was named as the advanced radiation resistant ODS steel (ARROSTM).On the basis of this ODS steel composition, an optimized fabrication process of structural components such as plates, sheets and tubes has been established through various process conditions in mechanical alloying, hot/cold working, and heat treatment processes. These R&D activities are expected to contribute to the realization of ODS materials in the future.INTRODUCTIONA sodium-cooled fast reactor (SFR) is being developed at the Korea Atomic Energy Research Institute (KAERI) with a view to economics, safety, reliability, and sustainability. The prototype Gen-IV SFR with a capacity of 150 MWe is under design, and this prototype reactor is scheduled to operate from 2028. For a commercial SFR system application, it is necessary to develop an advanced structural material having both high creep strength and irradiation resistance at high temperatures (Jeong, 2014). Oxide dispersion strengthened (ODS)steel is one of the most promising structural materials because of its excellent creep and irradiation resistance on the basis of uniformly distributed nano-oxide particles with a high density, which is extremely stable at high temperatures under a neutron irradiation environment for a prolonged operating period(Kim, 2016). As the first step, several batches of ODS steel were designed and the candidate samples with a 2 kg scale each were fabricated by mechanical alloying, hot isostatic pressing and hot rolling processes. The mechanical properties of these samples were evaluated. Up to now, two candidate materials with chemical compositions of (in wt%) Fe-10Cr-1Mo-0.5Mn-0.1V-0.25Ti-0.35Y2O3 was selected as representative materials, and these materials were named as the advanced radiation resistant ODS steel (ARROSTM).The next step was to optimize the fabrication process of the ARROS compositions for in-core structural components such as the fuel cladding tubes of a SFR. An optimized fabrication process of fuel cladding tube with a composition of ARROS has been established through various process conditions in mechanical alloying, hot consolidation, hot/cold working and heat treatment processes. Joining technologies of the ODS steel tubes is being developed using solid-state welding such as magnetic pulse welding, friction stir welding and diffusion boding. It is expected that the development of ARROS will contribute to the realization of a commercial SFR with high economics and sufficient safety in the future. In this paper, the study of fabrication process of ARROS structural components is introduced."

Jan 1, 2017

By J. Bardinas

"The use of autogenous mills has become widespread, owing to their capacity and favorable capital and operating costs. Optimal operation of these systems is critical, given their high energy consumption and effect on downstream processing. A considerable effort has been spent over the years in the development of advanced control systems to achieve a better performance in this regard. However, despite significant advances, the problem still remains challenging, owing to the nonlinear behaviour of the system with respect to the mill variables, and, the unmeasured ore variability come from the mine.The mill load, in particular, can be seen as a state variable of the mill, which could be important for; modelling and control, and, important insights into the mill behaviour. In this investigation, time series cluster analysis was performed using online mill load measurements in order to identify the different control states of the mill. More specifically, this time series was divided into short non-overlapping segments. A distance matrix was set up for each segment and the information was captured by means of textural features, similar to that used in multivariate image analysis. These wavelet and grey level cooccurrence matrix features could subsequently be used to rapidly identify the normal operating conditions from the feed disturbances in the mill.In principle, the methods and models presented here, once suitably validated and calibrated, could be used in online process monitoring of autogenous mills. They also could serve as a foundation for developing more advanced process control models."

Jan 1, 2016

By Jean-Jacques Bouillon, Michel Jébrak, Stephane Faure

"Le gisement polymétallique (Cu-Zn-Au-Ag) des Mines Selbaie est forme par un réseau de filons encaisses dans une séquence de pyroclastites felsiques du sill on Harricana-Turgeon. Les minéralisations sont encaissées dans le tuf de Selbaie, situe sous une épaisse séquence d'ignimbrites Iitées. Ce gisement se distingue des autres gites archéens par une chronologie atypique des minéralisations: les veines de chalcopyrite, de sphalérite et de galène recoupent un amas exhalatifpyriteux stérile. Un vaste halo d'altération hydrothermale a chlorite et mica blanc est associe à cette minéralisation.La mise en place des veines minéralisées est associée à une phase d'extension NNW-SSE. Le complexe volcanique subit, par la suite, trois phases de déformation. Une compression, orienté N-S, développe une schistosité à peine pénétrative et un réseau de fentes de tension. Une réorientation des contraintes locales selon une direction WNW-ESE conduit au chevauchement de I' écaille d'andésite et de tonalite de Brouillan. Un réseau conjugue de failles normales cassantes est associe au relâchement des contraintes."

Jan 1, 1990

By Noel W. Kirshenbaum

Difficulties and costs of transport markedly affect Canadian mineral producers because of distance from markets, weather conditions and rugged terrain. The chemical and physical nature of sulphide concentrates presents additional difficulties in handling and transport, resulting in higher costs which are ultimately borne by the mineowner. Troublesome properties include the thixo-tropic character of wet concentrates, freezing, susceptibility to autogenous heating, and fine particle size causing spillage and dusting losses. Canadian mineowners and shippers must contend with these problems and with stringent regulations governing the maritime shipping of concentrates. A "systems approach," in which complementary techniques in materials preparation, handling and transport are integrated, could reduce freight costs and losses for those selling concentrates, facilitate operations for those carrying and handling them and, in some cases, improve metallurgical processes in smelters receiving them.

Jan 1, 1969

By J. Stiksma, K. Buban, J. Oftsie, R. Kalanchey, S. Sadykov, E. McConaghy

The Kazakhmys zinc refinery in Balkhash, Kazakhstan, which employs the Dynatec Zinc Pressure Leach Process, officially launched autoclave operations on December 27, 2003. The Kazakhmys plant is the world&apos;s first greenfields zinc refinery based on Dynatec&apos;s two-stage pressure leach technology. Production of zinc was realized on February 9, 2004, when the first cathode was stripped. Currently the plant start-up is ongoing, with progression to two-stage zinc pressure leach operation and ramp-up to full design capacity continuing through 2004.

Jan 1, 2004

By Y. L. Mehta

The working experience of the Zinc Smelter, Debari, Udaipur with process modifications and iron control practices is described in detail in this paper. Most of the modifications were made at different times as part of capacity enhancement campaigns that led to distinct advantages, thereby increasing both zinc production and recoveries. This smelter came into existence in 1968 with a humble beginning of producing 18,000 metric tonnes (MT) of zinc per annum, using the conventional batch hydrometallurgical roast-leach-electrowinning technology. Zinc production capacity was increased stepwise to 45,000 MT, 49,000 MT and 59,000 MT, by making suitable process modifications and adopting new technologies, particularly in the leaching section. During these modifications, the process of iron separation as Moore cake was also changed to jarosite cake production. At present, jarosite is being disposed in a secured landfill at the Zinc Smelter, Debari (ZSD) and as Jarofix at the Chanderiya Lead Zinc Smelter (CLZS). As a result of subsequent in-house performance improvement and debottlenecking campaigns, this smelter could achieve further increases in production. Zinc production for the financial year 2005-06 was 81,000 MT.

Jan 1, 2006

By Maxime Tacher

BRP (Bombardier Recreational Products) designs and commercializes recreational vehicles such as watercrafts, sport boats, snowmobiles, ATVs... The Spyder roadster is the last product in the Can-Am product family lineup. To remain at the forefront of innovation, a hybrid motorization version of the Spyder is being developed in order to reduce fuel consumption and emission of greenhouse gases. But, the addition of electric components (e-motor, lithium-ion battery... ) raises the issue of added weight and volume. This article deals with the mass reduction of this Spyder by optimizing its frame.

Jan 1, 2011