Search Documents

By Sepulvedam Jaime E., Levi Guzmán Rivera

"Grinding media consumption rates and their dependence on key operating conditions in semiautogenous grinding mills is analyzed on the basis of a detailed mathematical model recently developed by Moly-Cop´s specialists which describes and takes into account the three primary media consumption mechanisms, namely: abrasion/corrosion, surface spalling and impact ball breakage. The influence of key mill operating conditions – such as ball filling, discharge grate opening, mill speed, lifter profile, and ball quality – on their corresponding grinding media consumption rates is explored via a variety of model simulations, discussing in every case the independent contribution of each of the indicated consumption mechanisms to the estimated total ball consumption rate.INTRODUCTIONA thorough understanding of the independent contribution of each grinding media wear mechanism is extremely important, especially in semi-autogenous grinding (SAG) operations where macrowear (spalling) and ball breakage cannot be ignored or neglected. The high impact conditions imposed in modern SAG milling environments has created serious challenges for grinding media manufacturers since their products must be able to perform with minimal breakage and surface spalling.GRINDING MEDIA WEAR MECHANISMFor SAG milling operations, at least 3 different mechanisms have been identified as the main contributors to the observed overall grinding media consumption, here referred to as: abrasion / corrosion, ball breakage and surface spalling.Wear by Abrasion/CorrosionThe abrasive/corrosive wear mechanism has been discussed in depth in previous publications (Benavente Hector, 2007; Guzman Levi, 2014; Sepulveda and Morrow, 2014). The most widely accepted approach to mathematically characterize the consumption (wear) kinetics of grinding media in rotary tumbling mills is known as the Linear Wear Theory (Prentice, 1943; Norquist, 1950; Sepulveda, 2004) which claims that—at each instant 't' after a grinding body enters the mill load—the rate at which the body loses weight is directly proportional to its surface area exposed."

Jan 1, 2016

By D. R. Jolley

"The selection of equipment for open-pit mining is an important decision which results in a considerable capital expenditure by the operator. The decision is complicated by the wide product range on the market. Certainly, equipment performance is an important criterion to consider in making the decision. Equally important, however, is the operating inter-relationship among the equipment. A poor balance increases production costs and waiting time as queues form at the bottlenecks. This inter-relationship is dependent on equipment performance, but it is also affected by management decisions (i.e. scheduling techniques).The purpose of this paper is to show how the computer is used to decide which equipment and operating decisions achieve the required production objectives at least cost. Actual mining of the pit is simulated over a period of time using different equipment and scheduling decisions. Production, waiting time and costs are evaluated for each alternative until the operator is satisfied that he has achieved the best result."

Jan 1, 1970

By Graham A. Davis, Michael Samis

The dramatic fluctuation in metal and energy prices in the last few years is causing mining companies to consider alternative analytical methods for mine design and valuation. The goal is to improve insight into unforeseen changes in the economic and project environment and to design projects that take advantage of management's ability to respond to these changes. Such flexibly managed projects will contain value that cannot be measured using traditional engineering economic approaches, further motivating the used of alternative, modern valuation methods. This paper considers the valuation of an uneconomic low-grade resource at an open pit gold mine using two of the most popular modern valuation methods, Dynamic Discounted Cash Flow and Real Options. Our analysis demonstrates that the conventional valuation method may incorrectly represent the value and risk attached to mining this type of resource because it is unable to recognize management's ability to respond to future events in a manner that minimizes losses and exploits advantageous business conditions. The results of this paper highlight the importance of recognizing flexibility and business uncertainty in both mine design and valuation.

Jan 1, 2003

A line of nine self-aspirating W emco cells, part of the Rougher circuit at Division Salvador, Codelco Chile, was retrofitted to allow operation with forced air. Each cell could be operated self-aspirated or with compressed air supplied through a 4-inch line equipped with a mass flow meter. Gas dispersion was characterized for the two modes of operation. Metallurgical performance was compared under self-aspirated conditions and with different gas profiles under forced air conditions. Cell characterization demonstrated that with forced-air the cells could not evenly distribute air across the cell volume. Bubble size increased with gas velocity, as expected, with no difference between self-aspirated and forced-air operation. A systematic increase in bubble size down the bank was found. Cumulative bubble surface area flux down the bank showed no major differences between surveys. However, grade-recovery curves revealed that the highest recoveries were invariably obtained with forced air operation. Plotting concentrate mass recovery vs. enrichment ratio showed that the line performance could be controlled over a wider range when forced air was used.

Jan 1, 2007

By R. Yost

"This paper describes a case study that illustrates how detailed geological engineering results were communicated to address a range of stability challenges in a producing mining environment. Instead of using standard geological engineering terminology, findings and recommendations were communicated as mine design options and mining responses to accommodate possible slope instabilities and associated risk. The resulting medium- to long-range mine plan integrated the potential slope instabilities and associated mining responses to provide a higher probability of planned resource extraction. It also reduced the potential for long-lasting production and processing delays.RÉSUMÉ Cet article décrit une étude de cas illustrant l’intérêt de la communication de résultats détaillés de géologie appliquée pour résoudre un éventail de difficultés relatives à la stabilité dans un environnement minier en production. Plutôt que d’utiliser une terminologie classique de géologie appliquée, les résultats et les recommandations ont été communiqués sous forme d’options pour la conception d’une mine et de réponses dans le contexte minier permettant de surmonter les éventuelles instabilités des pentes et les risques associés. Le plan de mine sur le moyen à long terme qui a résulté intégrait les instabilités potentielles des pentes ainsi que les réponses connexes dans le contexte minier afin de renforcer la probabilité de l’extraction des ressources prévue. Il réduisait également la possibilité de retards durables dans la production et le traitement.INTRODUCTIONSlope failures in an active mining operation are unscheduled but expected events, in the sense that the geotechnical design often assumes the potential for slope failure but cannot predict exactly when a failure will occur. Unfortunately, the geotechnical engineering cycle—characterization, slope design, displacement monitoring, instability management, and failure remediation—that is necessary to manage slope-failure risk is not always well known or understood outside the geotechnical engineering profession. The first introduction many personnel have to geotechnical engineering is when a slope failure starts to develop and appears to threaten the safety and livelihood of their workplace.At that point, the task of communicating the risk management of slope failure falls to the geotechnical engineer, who must summarize analytical methodology, design concepts, monitoring trends, and analysis results, frequently to an audience with limited exposure to the geotechnical field. All too often, the response has been to present a risk-management plan in the vernacular of geological engineering— using terms such as factor of safety (FOS), pore-pressure reduction, and slope unloading—instead of expressing the problem and solution in more readily understood mine production terms."

Jan 1, 2017

By Walter Herd

For the past eight years, No. 2 mine of the Cumberland Railway & Coal Co., Springhill-a subsidiary of the Dominion Coal Co., Ltd.-has had an unenviable reputation for bumps. As the workings extended in certain directions under a greater cover, these bumps increased in severity and it became apparent some change in the system of extraction was necessary if the mine was to continue to operate. In September, 1924, following several fatalities resulting from bumps, the Mines Depart~ of Nova Scotia requested from the U. S. Bureau of Mines the services of George S. Rice, Chief Mining Engineer of the Bureau, to report on the conditions then prevalent in No. 2 mine, Springhill. °This request was promptly and courteously granted. Mr. Rice made a full investigation and a comprehensive and helpful report, which is embodied in the 1924 Annual Report of the Department of Public Works and Mines, Nova Scotia. Prior to 1925, the room-and-pillar method was employed, and in January of that year (there being a cessation of work from March to August due to labour troubles) longwall retreating on the west side, on a limited scale, and in a small section on the east side of the mine, was started. The major portion of the east side was not operated on this system till August, 1926, as there was developed a considerable area ready for pillar extraction between an arbitrary boundary and a point up to which bumps of any consequence had not been experienced. In ?the interval, development work for longwall retreating below the 5,900-foot level was vigorously pushed.

Jan 1, 1929

By M. Mahdi Aboutalebi, Roderick I. L. Guthrie, Mihaiela Isac

"A preliminary computational fluid flow model has been developed to simulate the flow field of liquid steel in the mold region of billet mold casting. This study reports the effect of different Submerged Entry Nozzles (SEN) on the fluid flow in round and square billet, curved mold, casters. In this study, ANSYS Fluent 14.5 software was used to model the 3-D turbulent flow of liquid steel. The standard k-0 model was used to simulate turbulence in the mold region. Similarly, the species transport equations were discretized to simulate the dye injection test into the mold cavity. The behavior of flow in the mold region was validated against previous experimental work. Predicted results showed that different nozzle types plus the slight curvatures in the molds can significantly influence the flow patterns generated within the mold region, and thereby affect the finished quality of the billet products.INTRODUCTIONConventional Continuous Casting (C.C) processes are presently used to solidify more than 95% of the 1.5 billion tons of steel now produced in the world annually (World Steel in Figure, 2014). This overwhelming contribution of C.C processes for steel production is the prime motivation for this study, in order to understand and optimize the casting processes and thereby reduce internal defects and minimize energy consumption. The primary objective of all C.C processes is to maintain liquid metal purity during the casting process and to create a uniform flow within the caster so as to avoid internal and external defects. In this regard, studying fluid flows in the mold region of continuous caster has attracted many research groups, in both academia and industry, in recent years. The mold region is one of the most critical parts of the C.C. process, in which the transport phenomena associated with this region can significantly affect the quality of the final products. Thus, proper control of fluid flows within this region can be expected to greatly decrease both internal and surface defects such as Oscillation Marks (OM), inclusion entrapment, and Mold Powder Entrapment (MPE). In the casting process, the fluid flow in the mold region can be affected by a number of variables, such as; the flow control system (stopper rod or slide gate), nozzle geometry, SEN (Submerged Entry Nozzle) depth, casting speed, mold dimensions, gas injection, and the application of electromagnetic fields. One of the most influential and easily-changed fluid flows are the jets of steel issuing from the SEN. Nozzle geometries are variable, consisting of a number of exit ports, different port angles, and/or port sizes, the bottom shape of the nozzle, and the SEN immersion depth (Thomas, 2001). The SEN characteristics can markedly affect meniscus surface velocities, surface level profiles, and turbulence levels that can vary in terms of the frequency and the magnitude of their fluctuations."

Jan 1, 2016

The primary steel industry of the Prairie Provinces consists essentially of three companies whose total annual melting capacity, as of January 1, 1963, was 333,000 net tons. These companies have steel rolling facilities. In addition, there are five other companies producing steel castings by melting scrap in electric furnaces which, with the plants having rolling facilities, gives a total annual furnace melting capacity of 380,000 tons. Since 1954, the annual production of steel ingots and castings has ranged from a low of 66,588 tons, in 1954, to a high of 211,138 tons in 1961. The present facilities on the Prairies for making steel ingots from scrap, and rolling them to produce light merchant mill products, appear to be sufficient for many years ahead. Steel scrap, as electric furnace feed to make steel ingots for the present line of products, will probably continue to be available at reasonable prices either on the Prairies or from the north-central United States. It is recognized, however, that residual elements in scrap may be-come of greater significance and necessitate more rigid control of scrap quality.

Jan 1, 1963

By H. Wotruba, K. Neubert

Dual-energy X-ray transmission (DE-XRT) imaging is known from safety luggage inspections at airports. The use of DE-XRT technology for sorting applications in the primary raw materials industry has been the subject of numerous investigations. Beside other metal ores, X-ray transmission sorting is already used for the preconcentration of tungsten ore, gold ore and coal. The applicability of DE-XRT sorting is limited to ore types where differences in metal concentrations are measurable, based on an interpretation of X-ray images. Metal contents in particles occur in large varieties in terms of concentration, grain sizes, spatial distribution and mineralogy and therefore influence the X-ray absorption. As a result, each ore has to be tested individually for its suitability for DE-XRT sorting. The objective of current research at the Department of Mineral Processing (AMR) at RWTH Aachen University is to assess parameters influencing the detectability of rare earth oxides. Two approaches were followed: (1) Practical test work, based on artificial ore samples of defined compositions and (2) Computer-based simulation of absorption features of identical particle compositions. In total, more than 300 artificial samples of various compositions and metal grades were produced and X-ray images from DE-XRT sorting were analyzed. Results from the DE-XRT sensor were put into correlation with metal grades and particle sizes, to analyze influences and limits on the detectability of rare earth oxides. In addition, a new approach was tested in which the X-ray absorption of particles of various compositions was determined based on a Monte Carlo (MCNP) simulation. During the simulation, similar compositions, as used for the artificial samples, were tested and the X-ray absorption behavior during DE-XRT sorting was determined. A comparison of results from both approaches is used to assess the applicability of the MCNP-simulation for the prediction of the X-ray attenuation behavior during DE-XRT sorting.

Jan 1, 2016

By S. Foged

Umicore and MWH jointly demonstrated that mechanical dewatering of goethite and neutralised tailings significantly increased the life of a 30 ha tailings pond and improved the operation of the pond. Umicore operates one of its zinc production plants in Balen, Belgium. As part of its production process, an excess of neutralised and goethite¬containing tailings is generated. These have historically been stored inside large lined ponds. As the storage area of the current goethite pond was nearing its capacity, Umicore studied the potential for an extension to the existing embankment. However, this extension would face intense regulatory scrutiny, because the environmental and safety impacts were considered important. Together with Umicore, MWH suggested and investigated an alternative treatment approach consisting of mechanical dewatering prior to storage. A feasibility study was prepared where wet storage was compared to dry storage. Differences in safety risks, environmental impacts and economic costs were outlined. The study demonstrated that the life of the tailings pond could be increased from 6 to 22 years, seriously reducing the environmental impacts and safety risks at no significantly higher cost than would have been incurred with the continued operation of the existing pond. The results of the study are presented in this paper.

Jan 1, 2006

By Beatrice Pierre, Juan Carrasco

Altonorte began as a concentrate roasting operation in 1988 under the name of Refimet. In 1993, a copper smelter was built with a design capacity of 203,000 tonnes per annum of concentrate. Since 2001, many technological advances have been made in Altonorte, where the biggest Noranda Reactor in the world is installed being the first Noranda Reactor reaching above one million tonnes of copper concentrates processed per annum. In 2013, Altonorte was acquired by Glencore. Recently due to various new environmental regulations in Chile, Altonorte has evolved to new standards of operation in order to reach the vision of becoming a World Class Smelter. This paper describes the path followed to improve safety, environmental performance, process capacity, reliability, and productivity. The foundation for the growth and success in Altonorte is our People. Employee engagement and branding of our cultural journey is what allows Altonorte to face the future with the certainty of becoming a World Class Smelter. INTRODUCTION Altonorte is located in Antofagasta, the mining capital in the north of Chile and is the last smelter built in Chile practically completed with second hand equipment. The biggest technological change in Altonorte occurred during the phase 3 expansion in 2003, where the old Reverberatory furnace was shut down and replaced by the biggest Noranda Reactor installed in the world. The vessel measures 5.3 m × 26m. ºAdditionally, this project contemplated a new rotary dryer, three (3) new Peirce Smith converters, new anode furnaces and a new Acid plant. The nominal capacity was to treat 816.000 tons of new concentrate per year. In 2008, a new expansion phase was implemented where a new double absorption acid plant replaced the oldest acid plant. Bottlenecks such as blowing capacity and oxygen availability were solved installing a new air blower and a new contract was negotiated with our oxygen supplier to increase oxygen availability up to 683 tpd. This improvement defined the current nominal capacity of 1.100.000 ton of new concentrate per year. Current process description All concentrates are received by trucks directly from domestic mines or from the Antofagasta international port in cases of imported concentrates; the concentrate warehouse has a capacity of 25 kt where the blend is prepared to feed the smelter.

Jan 1, 2019

By O. Mejia

"As study was undertaken to investigate the relationship between mill liner wear and grinding energy efficiency and to assess the opportunity to control mill speed to improve energy performance as mill liner wears. The study involved analysis of plant operating data and liner wear profiles over time. The operating work index was found to be an effective tool to identify the decrease of grinding efficiency along the liner service. The plant data show that the mill grinding efficiency as determined by monitoring the operating work index, and throughput decreases as liner wears. However, efficiency and throughput can be maintained by either changing the liner more frequently or by increasing the mill speed. Two scenarios for increasing mill throughput were analyzed. The first one involves changing the liner before the efficiency drops and the second one requires increasing the mill speed from 75% to 79%. Both scenarios show financial benefits that can be used in mill operations.INTRODUCTION The analysis of the mill power draw is used in this study as a key parameter for comparing mill liner profile and its effect on mill performance. Current technology and simulation software used in the mining industry do not factor in the impact of liner wear profiles in grinding efficiency and mill throughput (Toor, 2013). To address this gap, this study provides an analysis of key factors affecting mill throughput and grinding efficiency: mill speed, ball loading, and liner profiles. Several years of plant mill operating data, published research papers, and MillTraj® simulation results are used to demonstrate that face angles impact grinding efficiency and throughput and that mill speed can be used to overcome this problem. Moreover, the liner profile wear analyses clarify a mismatch between actual and estimated power draw calculations."

Jan 1, 2019

By E. Norton

"Even though the subject of this panel discussion is dust control, rather than dwell on the design aspects of dust collection systems which are well documented in numerous publications, :it was considered more pertinent to the present economics of mining to examine the energy costs involved.At the present time, the facts of shrinking fossil fuel reserves and spiralling fuel costs are being constantly brought to our attention. Industry is being motivated to consider the possibilities of incorporating heat recovery systems in areas where they prove to be economical. Unfortunately, it is not a simple exercise to determine if the installation and operation of heat recovery equipment is feasible and economical. Each process involving heat recovery potential must be thoroughly studied in all aspects.In a paper presented at the 1975 Annual General Meeting of the Canadian Institute of Mining and Metallurgy in Toronto, Ontario, entitled ""The Influence of Energy Conservation on Concentrator Design"", it was stated that the largest single energy consumer in winter is space heating with the largest portion of this supplied to crushing and screening plants. (1) Within the scope of this panel discussion we will study, as one example, a crushing and screening plant using natural gas heat in the province of British Columbia and we will explore the feasibility and economics of installing air-to-air heat recovery equipment."

Jan 1, 1976

By M. Oliazadeh, A. Vazirizadeh

"The inclusion of small amounts of silicon, phosphorus and sulphur in iron ores or concentrates can have a profound effect on the steel making process and thus on the final iron and steel products. In nature however, it is inevitable that iron deposits contain unwanted elements. Each element has its own distinct effect on the final steel product. The effect of high silicon is the formation of gray iron. Phosphorus mainly increases hardness and strength, lowers solidus temperature and increases fluidity and cold shortness. Finally sulphur contamination causes cracks in the iron texture when smelting and forms white iron when casting. Overall, the acceptable level of phosphorus, sulphur and silica in the iron concentrate should be less than 0.04%, 0.15 % and 1.5 % respectively.Scarcity of high grade iron ores necessitates using lower grade ores with higher amounts of impurities. The purpose of iron concentrators is to increase iron grades to an appropriate level suitable for steel making as well as removing impurities. Although many impurities can be traced in the ore, the most predominant impurities are limited to one or two elements. In this paper the beneficiation methods for removing SiO2, P and S are presented, including flotation, and the parameters that need to be considered in the design of beneficiation plants are discussed. Finally industrial cases are discussed along with their metallurgical performance.INTRODUCTIONIn metal sector, value of iron ores and concentrates is determined by iron percentage as well ascontent of:• Useful elements (Mn, Ni, Cr, V, Ti): natural alloying elements in steel• Deleterious impurities (S, P, As, Zn, Pb, K, Na): impair metal properties or complicate operational process in blast furnace• Fluxing components (Si, Ca, Mg,, Al)Sulphur and copper result in red-short, phosphorus is the cause of cold brittleness and arsenic and copper decrease welding characteristics. Sulphur should not exceed 0.15 in commercial ore. Acceptable sulphur content in ores and concentrates for producing sinter and pellets is 0.6%max, as sintering and heat hardening of pellets remove sulphur 60-90%. Phosphorous content in ores, sinter and pellets is limited to 0.07%-0.15%. 0.00.1% As max, 0.1-0.2% Zn max and up to 0.2% Cu are allowed in iron-ore part of the blast furnace burden for the production of standard conversion pig iron. Slag-forming components are divided into basic oxides (Ca, Mg) and acidic (Si, Al). Higher ratios of basic to acidic oxides are preferred since this reduces raw fluxing material."

Jan 1, 2016

By A. Bascetin

The mining industry in Turkey has been developing in the last 10 years. Mine wastes and tailings have thus been increasing, depending on the rising production rates. There are many problems related to accidents that occur in tailings damps. In this study, the applicability of the surface paste disposal (SPD) method for a Pb-Zn mine in western Turkey was examined. Density was 3.084 and specific surface area was 0.899 m2/g. The mill tailings have very low plasticity and show characteristics of clays and silts in terms of the Unified Soil Classification System. The particle size distribution of the tailings was 39.2% particles finer than 20 µm. The results of this study showed that the physical and chemical properties of mill tailings make them suitable for SPD.

Aug 1, 2013

By Deborah A. McCombe

"There are a number of important dates that must be disclosed when a Qualified Person (QP) is preparing a technical report for securities purposes. The dates are discussed in NI43-101 and the Form of the Technical Report, NI43-101F1. •,Effective date of the technical report •,Possible revision date of the report •,Effective date of mineral resources and mineral reserves •,Date of the personal inspection (site visit) •,Signature date of the date report (execution date) •,Date of the certificate of the QP •,Date of the consent of the QP The effective date of the report is basically the cut-off date for the information that is included in the technical report. The effective date should be close to the signature date. If there is too long a period between these dates, the QP runs the risk of new material information becoming available and then the technical report would no longer be current. The effective date is disclosed on the title page of the report and on the signature page. If a technical report needs to be revised to correct problems or disclosure deficiencies identified by the regulators, the QP will normally need to include a revision date on the title page of the report to distinguish the revised version from the original version. In these circumstances, the regulators will request that the original date of the report remain on the title page and the revised date will be below it. When a technical report must be revised, the QP must resign and date the signature page of the report and provide a new certificate and consent."

Jan 1, 2003

By L. Lamothe, C. H. The

"Pilot precipitator tests were conducted at Noranda's Horne Smelter in late 1978 to evaluate methods of improving converter dust collection efficiency. A bout 35 Nms/min. of converter off-gas were isokineticatly diverted from the converter flue to the pilot precipitator leased from Flakt (Canada) Ltd., consisting of three fields, one transformer-rectifier set per field and 77-m2 total collecting plate area. The effects of gas volume flow rate and conditioning the gas with sulphur trioxide and/or additional moisture were tested. II was found that gas flow rate and moisture level had the most pronounced effect on collection efficiency. Based on a techno-economic assessment of different options for improving converter Courell efficiency, waffle hoods and water sprays were installed on the converters to reduce air infiltration and increase the moisture level in the gas.BackgroundThe Horne Smelter of Noranda Inc. is situated in northwestern Quebec and, since the closure o f the min e in 1976, has been operating as a custom smelter. The concentrates treated at the smelter come from various mines with mixed sulphide ores , many o f them containing significant amounts of lead and zinc which makes dust collection in electrostatic precipitators mo re difficult than normal.As part of a continuing program on reducing smelter dust emissions, the No . 6 Cottrell was installed in 1972 up stream of Nos. 2 and 4 Cottrells (in parallel) in a n attempt to improve dust collection by increasing the over- all precipitator capacity ( Fig. I). However, it has never per formed a t its designed efficiency o f 94%. The average efficiency established in various test s was in the range of 60 – 65%."

Jan 1, 1985

By J. P. Bennett, K. S. Kwong

Slagging gasifiers are used to produce chemicals and/or electricity from feedstocks such as coal and/or petroleum coke. A gasifier environment includes pressures from 400 to 1000 psi, temperatures from 1250-1550°C, are cyclic, reducing gases of CO and 112, and molten ash that interacts with the refractory liner materials. The high Cr2O3 refractory liners of gasifiers fail within 3 to 24 months. Gasifier users seek materials with increased reliability and service life. This paper discusses causes of refractory failure and efforts to increase refractory service life.

Jan 1, 2004

By R. H. Pemberton

"THE Mattagami district of Quebec has, during the past few years, experienced intense exploration by virtually every mining company operating in Canada. As a result of this activity, a number of well-mineralized zinc-copper bearing bodies have been found, some of which will almost certainly go into production. Much of the area has undergone what is now termed ""Saturation Prospecting"" or intense and detailed geological and geophysical surveying, followed by the drilling of nearly all possible bets. Considering only the airborne geophysical surveying, some blocks of ground have been flown by virtually every geophysical instrument which has to date been installed in an aircraft. A list of these different geophysical instruments would include: l. Fluxgate-type total field magnetometers 2. Vertical field magnetometer ,3. Nuclear-precession magnetometers 4. Single-frequency out-of-phase electromagnetometers 5. Dual-frequency out-of-phase electromagnetometers 6. Horizontal component measuring electromagnetometers 7. In-phase and out-of-phase electromagnetometers8. Dip-angle measuring electromagnetometers."

Jan 1, 1961

By J. A. Brusset

THE Greenhill mine of West Canadian Collieries, Limited, is situated at Blairmore, Alberta, and produces 2,500 tons per day of bituminous coal. On Monday, October 25th, 1943, smoke was discovered by a party of firebosses on their regular weekly inspection of air-ways. Probably the fire had been smouldering for several days but, as it had started on the outcrop at the top of an old raise filled with dirt, only a small quantity of smoke could filter through, and the plume of mist that crowns the fan at that season had prevented the fan-man from noticing it. This raise is only about 200 feet from the fan, and is 70 feet long between the fan-drift and the outcrop. It was impossible to prove the origin of the fire, as it had probably started several days before it was discovered, but it is possible that a careless smoker may have thrown a match into the opening at the outcrop, and that the old, dry timber had caught fire. The airways are in No. 2 seam, a bituminous seam 18 to 25 feet thick surmounted by shales and sandstones. Only 45 feet vertically above it is No. 1 seam, 12 feet thick, overlain by a strong conglomerate. In that vicinity, No. 1 seam had been worked out about ten years ago and the strata between the two seams are undoubtedly fissured. The pitch of both seams is 43 degrees.

Jan 1, 1945