Search Documents

By G. H. Babcock, D. A. Knight, V. G. Medina

"Production commenced at the Golden Sunlight Mine in 1983 and at Kidston Gold Mine in 1985. These projects were both constructed under the management of the Placer Dome Inc. (Technical Services) group of Vancouver, B.C.Golden Sunlight uses a conventional rod mill/ball mill grinding circuit while Kidston uses a SAG /ball mill, and later on, SABC circuit. Since the hardness of the ore and the fineness of the primary grind in both mines are about the same, a meaningful cost comparison can be made. The comparison is made on the basis of capital and operating costs.The result of this study indicates that a significant capital cost savings can be achieved in favour of the SAG /ball mill circuit when the ore is amenable to semi-autogenous grinding. With a good maintenance program, the operating cost for the SAG /ball mill circuit could also be lower that the conventional rod mill/ball mill circuit.HISTORYGolden Sunlight MineGolden Sunlight is a 5 530 t/d gold mine located near Whitehall, a small town 60 km east of Butte, Montana. Originally optioned by PDI U.S. in 1958, the development of the property waited until 1981 when economic conditions became favorable for the project to proceed.Semiautogenous grinding tests were conducted during the final stages of the feasibility study. The hard near surface ore was not quite amenable to semi-autogenous grinding. The best result produced from a series of tests using a 1.83 m diameter mill was a semiautogenous work index of 39. This is substantially higher than the 22 Bond work index of the sample used in the testwork. A conventional SAG/ball mill circuit for this ore will be extremely inefficient, and for this reason, this circuit was rejected in favour of a conventional rod mill/ball mill circuit."

Jan 1, 1991

By R. K. Sidhu, N. L. Richards, M. C. Chaturvedi

Nickel base superalloy IN-738LC, strengthened mainly by the precipitation of y' phase, is extensively used in hot sections of land-based and aero gas turbine engines. Fusion welding, which is one of the most commonly used joining techniques for the repair and fabrication of superalloy components, however, finds a very limited application in case of IN-738LC components, as the alloy suffers from HAZ cracking during welding and during subsequent postweld heat treatment (PWHT). The present paper reports on the two methods studied to reduce the HAZ cracking in as-welded and postweld heat treated GTA welded IN-738LC, viz., the use of various fillers during welding, and the use of appropriate heat treatments prior to welding. The results of the microstructural analysis and crack measurements indicated that the HAZ cracking in GTA welds of IN-738LC was significantly reduced by using age-hardenable fillers with Al+Ti concentration less than that in the base metal in conjunction with a preweld heat treatment developed by the authors.

Jan 1, 2006

By R. G. Hamm

A brief outline covering the shovels and draglines in use in the open-pit mines of Western Canada, including British Columbia, Alberta and the Yukon, is given, followed by the procedure for the selection of the correct wire rope for each application. Such fa ctors as wire rope constructions, lay directions and types of cores are mentioned. Once the correct wire rope has been selected, there are variousfactors that can affect the service fife ofthe rope and the reduction ofdown-time during rope change-overs. Factors such as hairpin winding, types of Becket loops, and shovel drum and bail adaptors are described.

Jan 1, 1979

By P. C. Garg

"IntroductionThe Central Mine Planning and Design Institute (CMPDI) of India, started planning the extraction of thick seams highly susceptible to heating in 1977by the French method of sub-level caving and/or multi-slicing. Nitrogen flushing was proposed for inhibition of heating by the author in one such project - the Kotadih colliery.Inhibition of heating was unheard of in the Indian coal industry before 1977-78. The usual practice was to seal off a district or a part of the mine or the entire mine when spontaneous heating occurred. With very little equipment in a normal bord and pillar district and a low production rate, the financial loss in capital assets and in production did not warrant any serious thought for inhibition of spontaneous combustion. With the planned advent of longwall mining, particularly sub-level caving, with heavy capital investment as well as high production potential, the sealing of a longwall face due to spontaneous heating could not be considered an appropriate solution.Principle of Inhibition of SpontaneousCombustionFrench engineers have established that a fire will not break out when oxygen is 15% or lower in the general body of the air. However, once a fire starts, the percentage of oxygen has to be reduced to 2% - 4% to extinguish it. It is this principle which has been used at Blanzy Coalfield in France to inhibit heating and it is claimed that this has retrieved the integral sub level method of mining. Nitrogen infusion has been used in Frence since 1978 to keep the oxygen content below 14% in the goaf."

Jan 1, 1987

By C. M. Díaz, P. J. Mackey, P. Coursol

In a recent paper [1], the present authors discussed calculated energy consumption numbers in copper sulphide concentrate smelting for four different smelting technologies. For the present study, from among these technologies, they selected the Noranda/Teniente continuous bath smelting followed by Peirce Smith (PS) converting route to investigate the impact on total energy requirement of some key process variations, such as tuyere injection of dry concentrate vs. slingering of wet concentrate over the molten bath, continuous converting vs. conventional batch PS converting and commercially proven slag cleaning alternatives. In their calculations, the authors used the same thermochemical model and methodology used in their earlier paper. This approach to explore plant design options provides an interesting basis for evaluating flowsheet modifications that could lead to significant copper smelting energy savings. The METSIM software was used in the present paper to carry out heat and mass balance computations for 8 different flowsheet configurations. The results are presented and discussed in the paper with respect to copper recoveries, energy requirements and CO2 emissions.

Jan 1, 2011

By W. C. Zhu, C. H. Wei, L. L. Niu

With an increase of mining depth, a series of mining-induced hazards such as rockburst, coal and gas outburst, roof collapse, and water burst are getting more serious and more frequent. The intrinsic mechanism responsible for the occurrence of mining-induced hazards is the damage and unstable failure of rockmass or coal seam. The most distinct difference between deep and shallow levels is the so-called three ‘high’ (H3) conditions, i.e. high geo-stress, high fluid pressure and high geo-temperature. Therefore, the response of rock or coal to the deep mining operation is a phenomenon involving thermal (T), hydraulic (H), and mechanical (M) processes. Most importantly, mining excavation may vary the rock stress condition greatly, which may be a key factor to trigger the mining-induced hazards such as rockburst. In this regard, it is of great significance to clarify the damage and failure mechanism of rock and coal under coupled THM conditions, in order to clarify the rock failure mechanism responsible for the occurrence of mining-induced hazards. Thereafter, the mining-induced hazards cannot be predicted with confidence by considering each process independently. Of course, the requirement to include coupling of these processes depends on the specifics of the mining-induced hazards under consideration. For example, the water inrush is considered as a coupled hydro-mechanical (HM) process, in which the unstable failure of rockmass occurs under the combined contribution of geo-stress and water pressure. As for the coal mining at depth, in addition to high geo-stress and gas pressure in coal seam, the high geo-thermal condition that may greatly change the adsorption / desorption of gas and gas flow should be taken into account. Firstly, a general-purpose mathematical model for rock damage and failure process under coupled THM conditions is formulated based on damage mechanics principle, and it is solved by finite element method (FEM). In this model, the deformation and damage of rock, fluid flow and thermal transfer in rock would interact with each other, one process affects and initiation and progress of another. Then, the model is used to predict the mining-induced water outburst, where it is simulated as coupled hydro-mechanical (HM) problems. Based on the numerical simulation, the dimension of water-proof pillar is designed. Finally, the gas drainage from deep coal seam is numerically evaluated, where the coupled coal-gas interaction considering the effect of gas adsorption/desorption, gas flow in coal seam and geo-stress and geotemperature, is comprehensively taken into account. The proposed model could be used for clarifying the mechanism of mining-induced hazards in deep-level mining.

Jan 1, 2015

By G. R. Elliott

Foreword The office of the Supervisory Mining Engineer, a branch of the l. Federal Government, is financially interested in no oil company and has no stock to sell. This office, however, is deeply interested in the proper and efficient development of Canada's natural resources. The people of Canada are interested in the petroleum development in Turner Valley for two principal reasons: As represented by the Department of the Interior, they are the largest owners of petroleum and natural-gas rights in the field; As a nation, they are vitally interested in the development of petroleum and natural gas as a national asset, and therefore, also, in all productive property, no matter who directly controls the leases. As has been stated by Mr. Charles C. Ross, Supervisory Mining Engineer, "The Department, being responsible for the administration of these public resources, necessarily requires regulations to protect them from abuse by lessees. Our portion of this responsibility is to record a complete history of all drilling operations and to see that proper drilling methods are adopted to prevent damage and wanton waste of the valuable natural resources under discussion." Not only does our position necessitate an impartial and a judicial viewpoint, but, being day by day in touch with all operations in the western provinces, we are uniquely situated to comprehend both individual and general problems.

Jan 1, 1930

By P. Botane, A. Cailleau

"Compagnie Miniere Esperance operates a gold primary ore body. The ore is processed through crushing, grinding and gravity concentration generating tailings with remaining fine gold. Analyses of the tailings proved a residual gold grade sufficient for a chemical treatment.As lab tests proved the technical feasibility of a pre-concentration using flotation, an on-site pilot operation has been carried out to assess the continuous circuit performances, define the best configuration and obtain enough data for the industrial circuit sizing.Data collected during the pilot campaign have been used for calibrating a process simulator built with the USIM™ PAC software. The simulator validated the feasibility of upgrading the existing plant, including the reprocessing of tailings to obtain a good fine gold recovery in a small amount of concentrate. A preliminary capital cost has been achieved to assess the flotation workshop profitability.INTRODUCTIONCompagnie Miniere Esperance (CME), a mining company based in French Guyana, operates a gold primary ore body in open pit. The ore is processed through crushing, grinding and gravity separation in two stages: a top plant and a bottom plant. A “coarse” pond contains tailings of the top plant; this product feeds the bottom plant. Tailings of the bottom plant are stored in the “fine” pond.Analyses of the fine ponds proved a residual gold grade sufficient for a chemical treatment. However, direct cyanidation would require a too large installation, regarding the local conditions (accessibility, supplying and meteorological conditions).It has been then decided to test the feasibility of a pre-concentration using flotation. Lab tests have been carried out by SGS Lakefield (Canada) in March 2007, which proves the technical feasibility."

Jan 1, 2009

By Paul Guliov

Preliminary investigations of stone resources were conducted in the La Range, Johnson Lake-Pelican Narrows-Deschambault Lake and Creighton-Amisk Lake regions of Saskatchewan. The work identified a rich variety of accessible, attractive and technically promising stone resources. Ordovician dolomites in various combinations of red, buff, yellow, grey and purple are very dense and take a very good polish. These are classified as marbles in the industry and some rival the famous marbles of Verona, Italy. A wide variety of attractive granites have been identified. Among these is a jade green stone (charnockite) and ornamental banded granites (gneisses). A dark greenish to black stone (amphibolite) with white and red veining resembles the well-known Verde Antique variety of Vermont and Italy and surpasses it aesthetically and in engineering properties. Some of these stones have been displayed at Canadian and United States expositions where they received an enthusiastic response from the international stone industry. More detailed evaluation and test quarrying of promising deposits are required. Such work could be rewarding to the industry as some stone varieties in the province have the potential for gaining international markets.

Jan 1, 2001

By V. C. Pandolfelli, L. Paulino, C. E. Zangiacomi

The continuous improvement in aluminum industry over the last years has increased metal output at lower cost. The potlining plays an important role in this regard due to high cost involved and more recently in its environmental aspects. In order to increase potlife and thus minimize the aluminum cash cost, a systemic approach is needed, through investigating the main cathode failure mechanisms by using a pot autopsy as a powerful tool, and then making the necessary chances to achieve extended potlife. In addition, preheating and pot start-up may also damage the cathode if not performed with an appropriate technique or even if the lining materials are not specified correctly, among other factors. All these aspects will be presented and discussed in this paper. Increased potlife, especially now that the current is reaching values up to 300kA, will allow aluminum plants to match their goals more efficiently at lower costs.

Jan 1, 2006

By P. Kostuik

"Recent interest in the pipeline transport of solid mate-als has been sparked by the idea that, in an inflationary onomy, pipeline costs are more stable than the costs of any other transport systems. Pipelines have proved over 1e years to be dependable, records indicate that main-•nance and operating costs are comparatively low, and 1eir amenability to automation is of considerable im->rtance.The concept of hydraulic hoisting of solids from under-round, or cross-country hydraulic transportation of con-~ntrates and ores, is currently of prime interest to the ining industry. In general, this paper deals with a preliminary investi-ation of energy losses incurred while transporting a rela-vely heavy, crushed mine product, namely magnetite, oth vertically and horizontally. The basis and validity of everal equations derived by other experimenters to com-ute these losses is discussed. A theoretical analysis of ydraulic hoi:,,ting is made, and, based upon test results, calculation of horsepower requirements for hoisting an re under a given set of conditions is presented. Results indicate that:n vertical transport, the friction head losses are identical to those of clear water, and the total energy requirement for hydraulic hoisting then becomes a function of height of lift, concentration and specific gravity of the solids being hoisted. .-In horizontal transport, friction head losses can be calculated with reasonable accuracy using Bonning-ton's correlation curve. Losses computed utilizing Durand's correlation (K = 85) result in estimates which are too low by 10 to 30 per cent, an<l those calculated using Newitt's correlation (K = 1,100, K = 66) give friction loss values which are too high by 10 to 30 per cent . . -The theoretical horsepower (RMS-hp.) required for hoisting hydraulically is approximately half of that required for conventional double-drum skip hoisting."

Jan 1, 1966

By F. Rosenblum, P. Spira

"Self-heating of broken sulphide ore or waste rock underground can lead to ignition and cause serious problems in a mine operation. An extensive study has demonstrated that it is caused by oxidation of certain species of pyrrhotite. Self-heating was found to take place in two stages, first progressing from ambient temperature to 1000C with exothermic formation of elemental sulphur in the presence of moisture and oxygen, and proceeding to a second stage in which the sulphur oxidizes to SO2. Ignition may eventually follow. An apparatus was developed to assess the propensity of sulphide rock to self-heating and the potential for hazardous behaviour. The effect of temperature, time, rock size, and surface treatment with chemicals is presented. On the basis of these results, possible approaches for preventing a runaway reaction are suggested for further investigation.IntroductionThe oxidation of sulphide ore, waste rock or tailings backfill, which may cause hazardous conditions underground through heating, oxygen depletion and, in some cases, fire, is well documented (Farnsworth, 1977; Ninteman, 1978; Rosenblum et al., 1982; Reimers, 1987). The self-heating mechanism, nevertheless, has not been satisfactorily explained. The onset of heating from ambient temperature, in particular, has not drawn the attention of researchers. In the course of a previous study (Rosenblum et al., 1982) aimed at finding a method to assess the hazard from using sulphide tailings as backfill, the authors developed an apparatus to measure self-heating rate under controlled, near ambient conditions. This has since provided decisive information in backfill investigations in the Noranda Group.The test methodology devised for tailings failed to predict self-heating in a broken waste rock known to be active. Upon repeated testing, however, a freshly crushed sample began to exhibit appreciable heating and oxygen uptake (Fig. I). After 14 tests, the self-heating rate reached a plateau of about 4O°C/h and then fell progressively to < 5°C/h after 30 tests. It was hypothesized that weathering in the presence of moisture and oxygen during testing had caused the onset of self-heating. Active tailings, on the other hand, are exposed to natural surface oxidation and need not be weathered to show heating. Based on this finding, a new apparatus was developed capable of simultaneously weathering a sample of rock and monitoring its self-heating behaviour."

Jan 1, 1995

By J. S. Brock

Magnetic, electromagnetic and gravimetric surveys have played an important role in the mineral exploration leading to the discovery of three major massive sulphide deposits in the Anvil-Vangorda area of the Yukon Territory. During 1964 and 1965 a saturation prospecting program, relying heavily on the integrated use of airborne and ground geophysical survey techniques, led to the discovery of the Faro deposit, which was subsequently proven to be a 63-millionton lead-zinc orebody. Locating the Faro deposit, the largest found to date in this overburden-covered region, involved an exploration sequence requiring the selection of a favourable geologic environment, aeromagnetic and electromagnetic surveys, property acquisition of anomalous areas and detailed ground geophysical surveys, followed by rotary drill testing, detailed gravimetric surveys and diamond core drilling.

Jan 1, 1973

By J. F. Wright

The cold, or Kississing, Lake area in northwestern Manitoba was the scene of considerable prospecting and mining activity last summer. At the Sherritt-Gordon property, four diamond drills were at work exploring a large deposit of copper and zinc ore, and underground work was in progress on this deposit from two shafts. Some preliminary diamond drilling was completed in five other deposits, and surface exploration work was in progress at a dozen or more additional localities where copper and zinc sulphides were known to be present. Many prospectors visited the area and spent some time in search for new deposits, but apparently few discoveries were made; consequently, last autumn some returned a little disappointed in the area as a prospecting field. Although many visited Cold Lake area last summer in the search for mineral deposits, it should be emphasized that this new prospecting field is a very large one, and that to date only a small proportion of the ground has been examined, except in a very general way. Within the past 18 months, a village of several dozen cabins, and with a population of l00 or more persons, has sprung up on the shore of Cold lake, just west of the Sherritt-Gordon mine. This at present is the business centre of the area, and two banks, a post office - named Kississing by the Postal authorities - a Mining Recorder&apos;s office, as well as several restaurants and stores carrying a fairly complete stock of groceries, dry-goods, and general prospecting equipment, are already established.

Jan 1, 1929

By Ming’an Wei, Qifu Duan, Chengtie Wang, Jianmin Wu, Erdenet Mining Corporation, Lusheng Zhou, Wenjian Wu

"The development and industrial applications of magnetic liners have been around for decades. A Swedish company SKEGA first introduced the rubber magnetic liner, and then followed by the Chinese metal magnetic liners. Traditionally, both liners were used in secondary and regrind ball mills, especially for ores containing magnetic materials. Mostly steel balls or equivalent forged balls, usually below 60 mm in diameter, were used as grinding media. With the development of mineral resources over the years, SAG mills and larger ball mills have become the dominating components for comminution circuit design globally. Due to the larger ball mills and thus larger grinding balls (up to 80 mm) especially in non-ferrous metal industry, the application of magnetic liners has been very limited. Based on the new development of materials, the HMR Group Limited has been exploring new designs of magnetic liners which led to the invention of the Nano Steel Magnetic Liner (NSML). Recently, NSML had a successful application in a 5.5m x 6.5m ball mill with 80 mm balls at the Erdenet Copper Mine in Mongolia. Although the first set of liner had a service life of 12 months, the design of the second set was modified and improved to accommodate the operating conditions, which is expected to reach least 24 months service life. The original manganese steel liner only had about 8 months liner life.1. IntroductionMineral processing is an essential operation for the development and utilization of mineral resources. The effective concentration of various useful minerals depends on sufficient liberation of the mineral particles in the ore. The crushing and grinding process such as ball milling are the most common way to achieve proper liberation size. Mill liner is an eternal topic for the operations, not only because it protects the equipment, but also affects the mill grinding efficiency and availability. In recent years, magnetic mill liners have been developed that can easily meet the production targets with numerous benefits, such as zero maintenance, reducing specific energy consumption and improving grinding efficiency."

Jan 1, 2016

By R. R. Tatiya

"The ultimate aim of a mine design is to determine the development work involved and resources required by adopting one or more specific alternatives. A part of the process is the production of mining plans/designs, an outline of the amount of work and costs involved as well as a prediction of the revenues expected. The paper aims to examine these aspects of mine design using the computer models developed. These models are capable of designing and performing economic analysis for one or more stopes for a continuous orebody. IntroductionTatiya and Allen (1987) have described ’defining stope boundaries using a computer.’ Using the stope boundaries defined or even hypothetical ones, algorithms have been prepared to design the layouts of the following stoping methods: 1. sublevel stoping (longitudinal as well as transverse);2. DTH (Down-the-hole) stoping; and3. flat back cut and fill stoping with posts and pillars.Tatiya (1989) presented this work at the 21st symposium on the application of computers and operations research in the mineral industry (APCOM). Economic analysis of a stope is the additional feature incorporated with these algorithms.The system has been tested by an economic analysis of the three stoping methods modeled for a small portion of a deposit of a copper mining complex. The deposits at this mining complex form lenses of varying shapes and sizes, having low copper content. These chalcopyrite lenses are steeply inclined with a thickness in the range of 5 m to 60 m. The strata are competent and suitable for underground mining.In different sections of the mines different sets of equipment are used to perform the basic unit operations. Some of the ore handling levels in the mines are trackless, the rest are tracked."

Jan 1, 1998

By J. Esson, R. A. D. Pattrick, M. K. Nimfopoulos, D. A. Polya, K. M. Michailidis

"Abstract-Economic Mn-oxide ore deposits of commercial grade occur in the Rhodope massif near Kato Nevrokopi in the Drama region, Northern Greece. The Mn-oxide mineralization has developed by weathering of continental hypogene rhodochrosite-sulphide veins. The vein mineralization is confined by tectonic shear zones between marble and metapelites, extending laterally into the marble as tabular, pod or lenticular oreshoots (up to 50 m ?? 20 m ?? 5-10 m). Supergene oxidation of the hypogene mineralization led to the formation of in-situ residual Mn-oxide ore deposits, and secondary infills of Mn-oxide ore in embryonic and well developed karst cavities.Whole rock geochemical profiles across mineralized zones confirm the role of thrusts and faults as solution passageways and stress the importance of these structures in the development of hydrothermal and supergene mineralization at Kato Nevrokopi. Three zones are recognized in the insitu supergene veins: (A) a stable zone of oxidation, where immobile elements form (or substitute in) stable oxide mineral phases, and mobile elements are leached; (B) a transitional (active) zone in which element behavior is strongly influenced by seasonal fluctuations of the groundwater table and variations in pH-Eh conditions; and (C) a zone of permanent flooding, where variations in pH-Eh conditions are minimal. Zone (B) is considered as the source zone for the karst cavity mineralization. During weathering, meteoric waters, which were CO2-rich (PCO2 ~10-3.8 to 10-1.4) and oxygenated (fO2 ~10-17 for malachite), percolated downward within the veins, causing breakdown and dissolution of sulfides and marble, and oxidation of rhodochrosite to Mn-oxides. Karst cavity formation was favored by the high permeability along thrust zones. Dissolved Mn2+ was transported into karst cavities in reduced meteoric waters at the beginning of weathering (pH~4-5), and as Mn(HCO3)2 in slightly alkaline groundwaters during advanced weathering (pH~6-8). Mn4+-oxide precipitation took place by fO2 increase in ground waters, or pH increase by continuous hydrolysis and carbonate dissolution. In the well developed karst setting, some mobility of elements occurred during and after karst ore formation in the order Na>K>Mg>Sr>Mn>As>Zn>Ba>Al>Fe>Cu>Cd>Pb."

Jan 1, 1997

By Geoff Goodyear

UHNL Corporate Profile ? Providing Helicopter Services since 1963 ? A Newfoundland Company head-quartered in Goose Bay, Labrador ? Operations, while primarily Atlantic Canadian, extend across Canada, the Arctic, Greenland ? 16 aircraft, all single engine / VFR Typical Industry Mission Profiles & Work Environments ? Types of missions include: ? Air Taxi & Executive Transport ? Mineral Exploration ? Forest Fire Suppression ? Medivac ? Wildlife Management & Research ? High Angle Rescue and Ice Blasting ? External Load & Long Line ? Mountainous Terrain Operations ? Aerial Application ? Power line Patrols & Construction The Helicopter ? Essentially the same aerodynamic principals as fixed wing but with some mechanical variations on the theme

May 1, 2001

By Evelynn Stirling

"The paper/presentation will review the evolution of diesel technology from older diesel engines (1990 vintage) through to the latest technology as a result of the ever changing emissions regulations. It will encompass the EPA Tier levels as well as the latest Euro Stage V emissions. The next step with technology will be to address the CO2 emissions, which translates to improving fuel efficiencies of the product as well as other technologies like battery electric, hybrid and fuel cells. As technology progresses it also becomes important to improve connective diagnostic systems to support maintenance practices and improve efficiencies. What will also be presented will be the key emissions changes to the different gaseous and particle mass elements as the products have transitioned from the EPA Tier 3 through to Tier 4 Final regulations. Offering a range of different technologies to the underground mining market matters as not all pieces of equipment will perform optimally due to its duty cycle and application. INTRODUCTION Rudolf Diesel built his first well-known prototype of the high-compression engine in 1897. Since that time, the diesel engine has evolved into one of the world’s most capable and reliable forms of power generation. Diesel engines can be found in a wide variety of vehicles and equipment, powering everything from agriculture and construction equipment to power generators and marine vessels. In the early days the emissions from diesels was very poor and extensive work has been accomplished over the decades to make the product more environmentally friendly. This is more important in underground mining where the space is limited and ventilation is expensive and challenging. DISCUSSION The key driver of the development of diesel technology is the legislation globally around engine emissions. The emission level requirements over the years has forced diesel engine manufacturers to build a deep technical understanding of the system and how to innovate and optimize key elements of the engine. Cummins expertise has been built over the years as the diesel engine has evolved from a relatively simple mechanical engine to an electronic system with advanced air handling, fuel system, after treatment, and controls. Cummins has also continued to expand into systems beyond diesel, including natural gas. Many new components have been added to diesel engines to reduce emissions while improving fuel efficiency and reliability and, at the same time, reduce the total cost of ownership to the customer."

Jan 1, 2019

By A. J. Petrina

"At Craigmont Mines Limited, Merritt, B.C., tests were begun in March, 1965 to evaluate the use of shotcrete as a method of ground support m development headings; previously, ail drifts had. required support, which was accomplished mainly by timber and occasionally by the use of rockbolts. The tests demonstrated conclusively the effectiveness of shotcrete for supporting Craigmont's ground. Gradually, the use of timber for ground support was virtually eliminated in favour of shotcrete. This paper describes the equipment used, the operation of the equipment, pertinent cast data and opera ting details. Also discussed are other uses developed for the shot-creting equipment, the use of reinforcing bar rockbolts, and a method used at Craigmont for lining long vertical ore passes with steel plate and concrete as part of the raising cycle."

Jan 1, 1968