Search Documents

By M. Abzalov

"Control of analytical data quality is usually referred to in the mining industry as Quality Assurance and Quality Control (QAQC), and involves the monitoring of sample quality and quantification of analytical accuracy and precision. QAQC procedures normally involve using sample duplicates and specially prepared standards whose grade is known. Numerous case studies indicate that reliable control of sample precision is achieved by using approximately 5% to 10% of field duplicates and 3% to 5% of pulp duplicates. These duplicate samples should be prepared and analyzed in the primary laboratory.Bias in the analytical results can be identified by inclusion of 3% to 5% of the standard in each sample batch. Several different standards are used, with values spanning the practical range of grades in the actual samples. A blank (a sample in which the concentration of metal of interest is below detection limit) should also be included. Standard samples alone cannot identify biases introduced during sample preparation, and therefore approximately 5% of the duplicate samples (coarse rejects and pulp) should be processed and assayed at another, external, reputable laboratory.This paper discusses techniques used for estimation of errors in precision and accuracy, and overviews diagnostic tools. It is shown that one of the most commonly used methods, the Thompson-Howarth technique, produces consistently lower results than other methods. These results reflect the nature of this method, which relies on the assumption of a normally distributed error, and thus produces biased results when errors have a skewed distribution. This study concurs with the suggestion of Stanley and Lawie (2007: Exploration and Mining Geology, v. 16, p. 265-274) to use the average coefficient of variation (CVAVR(%)) as the universal measure of relative precision error in mine geology applications: Le contrôle de la qualité des données analytiques est habituellement désigné sous l’appellation d’Assurance et Contrôle de la Qualité (ACQ), elle implique le suivi de la qualité des échan¬tillons et la quantification de la reproductibilité et la précision analytiques. Les procédures des pro¬grammes d’ACQ impliquent habituellement l’usage de duplicata et de standards analytiques dont la teneur est connue. Plusieurs études de cas indiquent qu’une bonne fiabilité du contrôle de la précision des échantillons est atteinte par l’usage de 5% à 10% de doublons sur le terrain et de 3% à 5% de doublons de pulpe. Ces duplicata devraient être préparés et analysés au laboratoire principal.Un biais des résultats analytiques peut être identifié par l’inclusion de 3% à 5% d’échantillons standard dans chaque envoi d’échantillons. Plusieurs standards sont utilisés, avec des valeurs couvrant l’étendue des teneurs habituellement rencontrées dans des échantillons réels. Un blanc (un échantillon dans lequel la concentration d’un métal donné est sous la limite de détection) devrait aussi être inclus. L’emploi exclusif d’échantillons standards ne permet pas l’identification de biais résultant de la préparation des échantillons, de telle sorte qu’environ 5% des duplicata (rejets grossiers et pulpes) devrait être traités a un autre laboratoire indépendant et fiable.Cet article passe en revue les techniques utilisées pour évaluer l’erreur liée à la précision et a la reproductibilité, et effectue aussi un survol de divers outils diagnostiques. Il ressort de cet examen qu’une des techniques les plus fréquemment utilisées, la méthode Thompson-Howarth, fournit des estimés systémati¬quement inférieurs à ceux provenant des autres méthodes. Ces résultats sont un reflet de la nature de cette méthode, laquelle assume une distribution normale de l’erreur, biaisant ainsi les résultats lorsque l’erreur présente une distribution asymétrique. La présente étude recommande de privilégier l’usage du coefficient moyen de variation (CVAVR(%)) en tant que mesure universelle de la précision relative de l’erreu"

Jan 1, 2008

By F. D. Ball, D. E. Gemmell

"Coal mining in New Brunswick dates from the year 1639, when, as today, coal was produced from the area surrounding Grand Lake near the geographic centre of the province. Current production by N.B. Coal Ltd. is approximately 453,000 tonnes per year and comes from a single, thin Pennsylvanian age seam. The history of development and understanding of the geological setting of New Brunswick coals is discussed, beginning with the work of A. Gesner in 1839. The lithostratigraphic sub-divisions of the Pennsylvanian strata proposed by various workers are summarized and the present hypothesis that only biostratigraphic subdivision is possible is detailed. The Pictou Group, which includes the New Brunswick coals, consists of repetitive sequences of sediments consistent with flu vial and upper delta plain sedimentation. The development of coal mining in the province has progressed from horse-powered stream-bank stripping operations prior to the late 1800s through to the present use of open stripmining techniques utilizing eight walking draglines of various sizes. During the intervening years the introduction and eventual phasing out of underground mining occurred with the near termination of the coal mining industry in the province prior to 1973. The coal seam worked by N.B. Coal Ltd. averages 46 cm in thickness, has never been found to be more than 76 cm thick and has both high ash (12.4 -31.1%) and sulphur (4.9-7.8%) content. The wide variety of coal beneficiation studies and tests completed on New Brunswick coals have lead to the conclusion that a washed New Brunswick coal product could be expected with 10 to 12% ash, 5 to 6% sulphur, and 30,225 to 31,388 1/gm. Recoverable coal reserves, including those in the area licenced to N.B. Coal Ltd. and those licenced, although not yet in production, to both the St. Lawrence Cement Co. Ltd. and Provincial Holdings Ltd. at Lake Stream and Beersvil/e, total 60 million tonnes. At present, coal in New Brunswick is removed from prospecting and staking and all existing and future coal exploration and development will be administered by agreement under the Mining Act. Based on the results of a recently completed drilling project undertaken by the Department of Natural Resources, seventeen coal exploration blocks which carry minimum work commitments will be offered to the New Brunswick Electric Power Commission on a sixty-day first right ofrefusal basis. Those blocks not taken up by the Power Commission will be offered under the same commitments to the private sector."

Jan 1, 1985

By Robert T. McKnight

"Traditional techniques for valuing resource projects companies have been primarily based on discounted cashflow methods (DCF) or by comparison to similar projects with an apparent market capitalization. Many resource projects are really forms of options to invest rather than a future cashflow stream. Employing the DCF method to value a resource project which is really an option to invest, can dramatically underestimate the real value of the project. The analytical tools required to evaluate options, while more complicated than the usual spreadsheets used for DCF, are becoming more easily available and usable by managers. This paper will discuss the background of options valuation and some of the tools which will make it easier for managers to estimate the value of projects and companies which have significant real option values.ResumeBob McKnight is a graduate of the University of British Columbia in Geological Engineering, supplemented by an MBA from Simon Fraser University. Following several years in the oil patch with Cities Service and Brascan, Bob returned to Vancouver in 1979 to work for Wright Engineers. He subsequently went on to work for Cassiar Mining, Getty Resources and Endeavour Financial before joining Pincock Allen & Holt Ltd. in 1998. His experience ranges from exploration to feasibility studies, financial evaluations of mining and oil & gas projects, due diligence, project finance, valuations and mergers and acquisitions. He has extensive international mining experience pertaining to such countries as Chile, Mexico, Uruguay, Thailand, Indonesia, Angola, Papua New Guinea, Kazakhstan.What are Options?Options have been around for centuries. They were familiar to Roman and Phoenician traders who were shipping cargoes from Mediterranean seaports. In the financial world, options are types of contracts that generally include the right, but not the obligation, to buy or sell a share, currency or commodity. The underlying commodity price or share price changes are assumed to be lognormally distributed. In this context, options are of two general types, ""call"" options and ""put"" options. Call options have the characteristic of having the right to buy a tradable commodity or currency at a predetermined price for a specified period of time. For the owner of call options, they become more valuable as the price of the underlying commodity increases. For the seller of call options, these options become an increasing liability as commodity prices rise, since there is the obligation to sell the commodity at a predetermined (perhaps lower-than-market) price. This characteristic of call options recently became high profile with the sharp rise in gold prices last year. The value of gold call options sold by certain producers increased their associated liabilities to the point where margin calls were made."

Jan 1, 2003

By A. K. Snelgrove

Introduction ?Concerning the inland commodities, as wel to be drawen from this land (Newfoundland) there is nothing which our East and Northe.rly countries of Europe doe yeelde, but the like also may be made in (ît) as plentifully by time and industry : Namely, rosen, pitch . . . metalls, and many moe. All which the countries will aford, and the soyle is apt to yeelde ... For besides these alreadie recounted and infinite moe, the mountains generally make shew of minerall substance : Iron very common, lead, and somewhere copper. I will not auerre of richer metalls: albeit ... more then hope may be concieued thereof. " - Narrative of Captain Hayes, second-in-command to Sir Humphrey Gilbert's Expedition, IJ83 (From Hakluyt). The investigations set forth in the following pages were made in the field in Newfoundland during the summer of 1927, and later in the laboratories and library of McGill University, and in the library of the Canadian Geological Survey at Ottawa, with the purpose of collating and adding to our knowledge of the geology of an area roughly wedge-shaped in outline, and nearly nine thousand square miles in extent, stretching across the centre of the island of Newfoundland, from the southwest to the northeast coasts. To the description of this district, which contains most of the known mineral occurrences of Newfoundland, the term mineral belt is here introduced.

Jan 1, 1928

By S. P. Cashin, D. Kashuba, W. Esplin

Barrick has had 6 autoclaves in operation at the Goldstrike Mine, North of Carlin Nevada, since 1993. The 6 autoclaves operate in parallel, processing slurry of gold ore. The gold in the ore is predominantly associated with, and encapsulated by, sulphide minerals. It is necessary to oxidize at least 90% of the sulphide mineral before the gold can be concentrated using a cyanide/carbon-in-leach (CIL) circuit. Sulphide oxidation chemical reactions occurring in the autoclaves are exothermic; however, the sulphide content in the ore is not high enough to operate the autoclaves in an auto-thermal mode. Heat from steam is added to the first 2 of 5 autoclave compartments to initiate the sulphide oxidation reactions. The steam used to heat the autoclaves is supplied by three boilers, which are fuelled with propane gas. The completion of a few operations and maintenance projects in the last 2 years has resulted in a 50% reduction in propane energy requirements. The autoclave operating temperatures were minimized. Excess oxygen addition was held as low as possible. The material of construction for the compartment walls inside the autoclaves was changed from brick to Titanium metal. And, the speed of the autoclave slurry agitators was increased. All of these activities had an impact on the propane energy requirements of the autoclaves. Presented below is a description of the autoclave systems, and a discussion of how the energy needs were reduced, resulting in significant operating cost savings.

Jan 1, 2004

By S. Feinstein, I. Reznik, Y. H. Hatzor, O. Shitrit, Y. O. Rosenberg, H. J. Vinegar, S. Nguyen

"We report the effects of porosity and total organic carbon (TOC) content on the mechanical behavior of organic-rich chalks, based on laboratory measurements. The organic-rich chalks are from the Senonian Ghareb and Mishash formations. This deposit is an immature oil-prone source rock, about 300 meters thick, situated at shallow depths (several hundreds of meters) in the Shefela basin in central Israel. The study is based on core data collected from the Zoharim borehole.Three main phases comprise the bulk volume of this rock: 1) carbonate mineralogical phase (predominantly calcite); 2) pores (mostly saturated with brine); and 3) solid organic phase (type IIS kerogen). The mechanical effects of porosity (23-45%) and TOC (4-19%) are evaluated based on bulk incompressibilities vs. volumetric fractions analysis. Volumetric fractions of mineralogical and organic phases were obtained by porosity, density and TOC measurements. Saturated rock bulk moduli were measured through ultrasonic velocity measurements. Saturated rock bulk moduli correlate best with the sum of kerogen and pore volume fractions, rather than each of them separately. The volumetric fractions were also used to define the range of bulk modulus of the organic-rich chalk, using the Hashin-Shtrikman upper and lower bounds. Based on Marion's Bounding Average Method (BAM), the normalized stiffness factor of the chalk averaged at w=0.197, indicating a soft pore geometry. Using the average normalized stiffness factor, the BAM predictions showed excellent match with the saturated rock bulk modulus and the sum of kerogen and pore volume fractions. Based on our findings, it is inferred that kerogen grains do not support the solid skeleton but are distributed between the minerals grains. We also propose here a straightforward approach for calculating the Hashin-Shtrikman bounds, based on TOC and porosity measurements. The mechanical effects of porosity and TOC indicated here are very important for the understanding of the influence of immature kerogen presence in highly porous chalks, as the Ghareb and Mishash formations."

Jan 1, 2015

By L. Salnais

"Aluminum alloy structural components f or aircraft designed prior to the early 1970s, were machined from 2024, 7075 and 7079 plate, bar and forgings in either the T3xxx of the T6xxx tempers. Protective treatments for these parts consisted of chromic acid anodizing and alkyd zinc chromate primer, plus a nitrocellulose lacquer for exterior parts.The major service problem with these parts was the frequent occurrence of exfoliation corrosion and stress corrosion cracking (S. C. C.). Therefore, 2024 and 7079 alloys, with min or exceptions, were not used in aircraft designed after the early 1970s. Replacement materials were 7075 and 7050 alloys in the overaged, exfoliation corrosion and S. C. C. resistant, T73xxx tempers.The use of improved materials together with the upgrading to chromated epoxy primers, polyurethane enamels and the introduction of water displacing corrosion inhibiting compounds have significantly reduced corrosion in aircraft. IntroductionThe prevention of corrosion in aircraft has been a challenge to aircraft designers for many decades. With the design of the first all-metal aircraft, the designer and builder were thrust into the relatively new field of protective treatments as corrosion started to become more prevalent. This resulted from the continually increasing importance and wider utilization of aircraft, and their exposure to a wider variety of ho stile environments such as urban industrial pollution, high humidity tropical areas and salt ladened marine environments.Corrosion advanced another significant step when, after World War II, designs of new and larger aircraft utilized larger and thicker metal sections in the manufacture of structural components. With thicker mill products came higher residual heat treat, fabrication and assembly stresses resulting in an increased number of stress corrosion and exfoliation corrosion problems.Apart from the exterior environment, aircraft interior s can be exposed to a number of fluids which are either directly or indirectly responsible for corrosion. The most common of the fluids is water which is usually introduced as a result of condensation, especially in pressurized fuselages, and spillage from lavatories, galley s and electrolytes from batteries. These fluid s have a degrading effect on protective treatments and are also corrosive to the substrate metal. Fluids such as phosphate ester hydraulic fluids and ester based turbine engine lubricating oil s are not corrosive to the substrate metal, albeit they do contribute to corrosion by the degrading effect on protective treatments."

Jan 1, 1988

By Dani J. Alldrick, Alastair J. Sinclair, Colin I. Godwin

"Abstract - The Stewart mining camp has a long history of precious and base metal mining. The camp is abundantly mineralized, with more than 200 widespread, varied, vein prospects, deposits and orebodies. These show wide variations in the mineralogy of ore, gangue and alteration assemblages, and wide variations in textures and structural settings. This report establishes the timing of the different metallogenic epochs and suggests a specific exploration application for systematic lead isotope analyses.Galena lead isotope ratios from a range of mineral occurrences indicate that all these varieddeposits formed during two main mineralizing events. Lead isotope data from the Stewart mining camp do not provide absolute ages for the formation of mineral deposits, but the relative distributions of data are consistent with dates determined in other studies. One ore-forming episode occurred in the Barly Jurassic and the other in the Middle Eocene. Both metallogenic epochs were brief, regional-scale phenomena. Sorne deposits from the younger mineralizing episode were em­ placed adjacent to or superimposed on the older deposits.Field and laboratory studies show that the two metallogenic epochs are characterized by different base and precious metal suites: Barly Jurassic gold-silver-zinc-lead-copper; and Middle Eocene silver-lead-zinc. Therefore, showings of different ages have different base and precious metal potentials and deserve different exploration emphasis. Lead isotope studies provide a reliable, cost-effective method for evaluating the age and commodity potential of small or recently discovered mineral showings and for setting exploration priorities on properties with several varied mineral occurrences . The determination of the age and metal potential of a prospect at an early stage of exploration may govern the urgency, intensity or even the necessity for further exploration work."

Jan 1, 1993

By Karl J. C. Harries

"6.1. INTRODUCTIONThis chapter comments on some of the more common types of agreements related to property examination and acquisition, other than the farm-in/joint venture agreement or common undertaking, which is dealt with in the next two chapters. Many of the comments made in Part IV of Chapter 4 apply equally to any such agreement. In addition, many of the comments in Chapter 8 and the examples in Volume II are most certainly relevant to many other types of agreement.6.2. RIGHTS OF FIRST REFUSAL1A right of first refusal is a right that obligates an owner to offer his property, or an interest therein, to the holder of the first right if the owner intends to sell or otherwise dispose of it. It may be triggered either by the owner wishing to offer his property for sale or by receipt of a bona fide offer to purchase his interest from an “outside” third party. The mechanics and procedures to implement a first right should be set out clearly in the agreement, and their basics are the same, whether the first right is a stand-alone document or is part of an acquisition agreement.2Rights of first refusal are common in agreements to permit some control over the disposition of an interest and there they can be a valuable provision. However, some explorationists feel that they are also a good stand-alone agreement to have while a property is being evaluated to decide whether or not it is worth optioning. The reasoning is that such an arrangement will tie up the property to allow a quick look and, if the property looks interesting, the balance of the term of the first right will give an ample exclusive period of time to negotiate with the owner and settle an acquisition agreement. In addition, the explorationist is protected by the first right if the owner decides to negotiate a deal with another party."

Jan 1, 2003

By W. W. Bake

INTRODUCTION IN IN JUNE, 1943, the main pillars of the Beattie Mine glory hole failed, allowing over a million yards of wet clay and debris to flow into the mine, completely filling all workings to within seventy feet of the 3rd level. The resulting Job of clearing these workings and rehabilitating the mine represents a unique and hazardous operation, seldom, if ever, previously encountered in Canadian mining. The purpose of this paper is to describe one phase of this operation -that of cleaning and rehabilitating the mine from the 6th to the 9th level -to outline briefly the events which led up to this work and to describe the techniques and costs involved. It will be noted that such costs, methods, and performance figures as are dealt with in this paper refer only to work in the internal shaft and adjoining workings from the 6th to the 9th level, previous work having been done under other supervision and management. The Beattie mine is in Duparquet township, northwestern Quebec, twenty miles northwest of the town of Noranda and twenty-three miles southeast of the town of La Sarre. The mine and the town of Duparquet, which it?supports, are accessible by highway from Noranda throughout the year. Production at the Beattie mine began in May, 1933, and up to June, 1943, twenty-one million dollars in gold and silver had been recovered from five and a half million tons of ore.

Jan 1, 1951

By A. R. Sorta, D. C. Sego

ABSTRACT The settling, shear strength, and index properties of oil sands fines-sand mixture tailings (FSMT) for a wide range of solids and fines content are investigated. Results indicate that the liquid limit of FSMT obeys a linear mixture law. The fines-water ratio (FWR) governs the permeability of composite tailings (CT) and CT with comparable geotechnical behaviour can be produced from the same initial FWR mixtures. A phosphogypsum (PG) dosage > 900 mg/kg does not improve the dewatering behaviour of CT. The undrained shear strength of FSMT at the liquid limit is approximately 2.4 kPa, but is dependent on fines content at the plastic limit.

Jan 1, 2013

By J. Paturaud, A. G. Villemiane, J. Y. Buffiere, D. Fabregue, M. Perrier

In this work, a detailed characterization of the cyclic damage mechanisms on duty in car heat exchangers has been carried out in order to improve their reliability. The material which consists in very thin (<0.3 mm thick) sheets formed of 3 co-rolled aluminum alloys (4045 /3916/ 4045) has been brazed in order to obtain metallurgical and surface conditions representative of those of the real components. Fatigue tests at constant stress amplitude have been performed at room temperature and 120°C in order i) to characterize the cyclic resistance of the studied materials and ii) to study the effect of temperature on the fatigue damage mechanism. The mechanisms leading to failure have been identified from post mortem fractographic analysis. The Wohler curves obtained show that, contrary to common structural Al alloys, this type of thin sheet brazed multi material can be cycled for several hundred thousand cycles at very high stress level (> ~ 80 % of the tensile strength). This behaviour is analysed with respect to the microstructure resulting from the brazing process and the low number of grains present in the sample thickness (around 5 grains).

Jan 1, 2015

By E. B. Wright

THE property of Falconbridge Nickel Mines, Limited, is in Falconbridge township, approximately thirteen miles northwest of Sudbury. From the mine and townsite, a gravel road leads to Sudbury and a branch line of the Canadian National railway to Sudbury Junction. The ore deposit is at the southeastern corner of the &apos;Sudbury Basin&apos;. It lies in a sheet-like mass, striking in an east-west direction, between norite to the north and greenstone to the south. The general attitude of the ore-body is vertical, but with frequent variations in dip of as much as 10° to the north or south. The deposit is very irregular in outline, the width varying from a few feet to eighty or ninety feet. In the vertical plane, rolls are frequently encountered. Gouge is very often present at one or both ore contacts. The norite to the north shows much jointing. The chief ore minerals are pyrrhotite, pentlandite, and chalcopyrite. The nickel content of the ore is usually double the copper content, average assays ranging from 2 to 2.5 per cent nickel and 1 to 1.5 per cent copper. The ore is of three main types: massive, breccia, and disseminated. The breccia ore, the most common type, consists of sulphides containing rounded inclusions of highly-altered country rock, which, in places, are so large that sorting is necessary in the stopes. In the norite, the breccia ore may grade into disseminated sulphides, which frequently are sufficiently concentrated for profitable mining. In places in the breccia ore, concentrations of solid sulphide masses occur. Until early in 1935, all mining at Falconbridge was by shrinkage scoping, but this method was found to be less and less suitable as greater depth was attained. When mining had reached the 1,000-foot level, ore drawn from large shrinkage stopes was found to have been diluted as much as fifty per cent by sloughing of the wall-rocks, caused by increased rock pressure and insufficient support. It was apparent that this method of stoping was un-suitable and -Mr. E. J. Martin was engaged to superintend the introduction of a method of cut-and-fill stoping.

Jan 1, 1938

By M. H. Leite, R. Corthésy, D. E. Gill

"La connaissance des contraintes naturelles qui prévalent dans les massifs rocheux est un prérequis indispensable pour la conception sécuritaire et économique des excavations comme on en retrouve dans les exploitations minières souterraines. Certains chercheurs se sont attardés à colliger les résultats de mesures de ces contraintes et les ont utilisés pour produire des modèles de prédiction basés sur leur traitement statistique. Ces modèles de prédiction sont très populaires auprès des exploitants miniers puisqu’ils permettent, du moins dans les étapes préliminaires de design, d’obtenir de façon s’apéconomique mais approximative, une partie des paramètres dont ils ont besoin. Dans le cadre d’un projet initié en 1994 avec la collaboration de l’IRSST, il a été décidé de produire un modèle de prédiction englobant une partie de la zone périphérique de la faille de Cadillac, soit une zone plus restreinte que le Bouclier Canadien utilisé jusqu’ici comme région pour l’élaboration de tels modèles. Pour produire ce modèle de nouvelles données obtenues avec une technique permettant d’exercer un excellent contrôle de qualité ont été ajoutées à celles déjà disponibles. Une telle régionalisation des données de base permet d’obtenir un modèle où les intensités et les orientations des contraintes principales sont beaucoup moins dispersées que ce que rapportent les modèles publiés jusqu’à ce jour. Enfin, il est démontré que le modèle proposé pour la région étudiée est en toute probabilité plus sécuritaire que les modèles plus généraux publiés à ce jour. Knowledge of the in situ state of stress existing in a rock mass is essential to the safe and economical design of underground mining excavations. Prediction models have been published, based on the statistical treatment of stress measurement results. Such prediction models are very popular among mine operators because they allow them, at least at a preliminary design stage, to economically obtain part of the information needed, even if this information is approximative. In 1994, a research project financed by IRSST was initiated aiming to produce a prediction model that would comprise a peripheral zone around the Cadillac fault. This region is more confined than the Canadian Shield on which the existing prediction models have been based up to now. In order to produce such a model, existing stress measurement results have been used in conjunction with new stress measurements that have been performed based on a technique which allows full control of the quality of the measurements. Restricting the data upon which the model is based to a more specific region gives a model in which the intensities and the orientations of principal stresses are far less scattered than the results published to date. Finally, it is shown that the proposed model is probably safer for the studied region than the models previously published."

Jan 1, 1998

By E. N. Gilje

"IntroductionDURING the past five years, over two miles of shaft sinking have been completed at Falconbridge. As sinking has continued, we have improved our equipment and technique with a resulting increase in efficiency. Throughout this period, all sinking has been done by contracting firms, under our direction and to our equipment specifications, with highly satisfactory results. Since 1949, Riddell shaft mucking machines have been successfully used in conjunction with the •benching method of sinking. Our most recent practice can best be illustrated by describing the method used in sinking No. 1 shaft at the Fecunis Lake mine.No. 1 Shaft, Fecunis Lake MineNo. 1 shaft, consisting of six compartments and measuring 13 ft. 11 l/2 in. by 19 ft. 9 3/8 in., outside timber (Figure 1), will be sunk to a depth of 4,170 feet. It was designed to accommodate two 10-ft.diam. Koepe hoists."

Jan 1, 1955

By R. A. (Dick) McIvor

"It is important to ensure that the basic mine hoist plant design fundamentals are incorporated into any new mine hoist plant project before detailed design engineering is commenced. Some of the basic design fundamentals to be considered are: hoist rope fleet and flight angles for good hoist rope coiling, hoist rope harmonic frequency study to ensure that the hoist rope does not run at full speed at a rope resonance frequency, head frame and shaft clearance diagrams to establish the optimum positions for the loading and dumping of the shaft conveyances, access in the head frame and shaft collar for hoist rope and shaft conveyance installation and removal. Failure to consider the hoist plant fundamentals before detailed engineering commences will result in extra costs for hoist plant redesign or a significant increase in operating and maintenance costs for the mine due to increased hoist plant downtime to perform tasks and a lower mine operating efficiency. INTRODUCTION The mine hoisting plant is the most critical single line component in the operation of a shaft sinking operation or a permanent installation. Bad decisions in the design and selection of the hoist plant equipment can significantly add to the operating costs and up-time in the operation of the mine. Mine hoisting plant equipment installed costs represent approximately 5 to 8 percent of the capital cost of a new mine, yet price sometimes becomes the deciding factor for procuring the hoist plant components, sometimes selecting used equipment that may compromise the design and maintainability of the mine hoist plant. Mine downtime can cost upwards of $100,000 per hour and it will not take a very long time to eat up all the so-called savings on hoist plant equipment purchases. This paper will provide guidelines for the design, selection, installation and maintenance of mine hoist plant equipment with the objective to having the right mine hoist plant with the highest operational availability and best maintainability. PRELIMINARY DESIGN INFORMATION Before any engineering commences, the following information needs to be obtained to allow the preliminary sizing of the hoist plant equipment: • Shaft depth: The shaft depth will influence the hoist rope selection based on the material and personnel loads anticipated for the mine design. The shaft depth will also influence the maximum speed of the shaft conveyances. • Annual production: The desired annual production will influence the required payload sizing with allowances for maintenance and inspections of the hoist plant equipment."

Jan 1, 2019

By T. G. Joseph, A. Chamanara

ABSTRACT: The chicken and egg scenario — where adverse truck motions cause ground deterioration and poor ground profiles cause adverse truck motions — is a downward deterioration spiral dominating our industry. If we remove one action, the reaction stops. A simple truck to excavator load data analysis and wireless communication system is outlined, which will provide visual assistance to the excavator operator in achieving improved load placement and balance in a truck body. This will reduce subsequent hauler duty cycle adverse motions and g levels that contribute to structural fatigue, higher tkph, reduced tire life, and ongoing maintenance of haul roads.

Jan 1, 2012

By Jian Li, Robbie McDonald, David Robinson

"The pressure oxidation of sulfide minerals at temperatures above 200°C enables the extraction of base metals, improves the extractability of gold from refractory ores, enables solubilisation of PGEs and can be used to hydrothermally upgrade base metal-containing feeds. Fundamental studies reveal that the solution chemistry (and mineralogy of the solids) during pressure oxidation can be manipulated with outcomes that include (1) increased leaching rates, (2) lower oxygen requirements and (3) the formation of chemically more stable residues. This paper presents examples describing how these outcomes might be achieved based upon fundamental investigations.INTRODUCTION The application of pressure oxidation to the processing of gold ores and concentrates dates back several decades and continues to be the process of choice at operations such as Pueblo Viejo (pyritic gold) which host the largest autoclave of its kind in the world (Barrick Gold Corporation, 2016). Commercial application to the processing of base metals and PGMs resides with long established processes such as the Sherritt process, ore specific applications such as by Noril’sk, at Sepon etc. or has not proceeded to date beyond pilot scale testing (e.g. Phelps Dodge, CESL, Activox, Platsol). Recently there has been significant interest in hydrothermal upgrading options for concentrates including the NONOX and Toowong processes (Rohner et al., 2016; Weidenbach et al., 2016). The latter options suggest directions where sound knowledge of the underlying fundamentals enables novel outcomes and efficiencies to be obtained. It comes as no surprise that investigations similar to those underpinning these developing processes can be traced back several decades. It is not the subject of this paper to provide a historical perspective of the relevant autoclave chemistries but rather, to present some potential opportunities suggested by studies in our laboratories. Topics to be discussed in this paper include (1) control of metal extraction rates, (2) control of iron-residue composition and (3) control of sulfur oxidation and hence acid generation and oxygen requirements. The work described will focus upon the pressure oxidation of a nickel concentrate."

Jan 1, 2017

By W. J. Tough

THIS paper offers examples of some of the typical calculations which occur in the ventilation of metal mines. The fi.rst section of the paper discusses the problems associated with natural-draft pressure; the second section presents the more common of the calculations concerned with the operation of mine fans; the third section illustrates the integration of the individual problems covered by the preceding sections into the larger problem of determining the operating characteristics of a fan for a particular mine duty. There is a very definite limit to the extent to which pure arithmetic can be successfully applied to the solution of min<; ventilation problems. As mines advance from the exploration, development, and initial production stage to the rime when underground workings become exceedingly complex, there is a considerable increase in the relative importance o theory and judgment in the solution of ventilation problems. These calculations illustrate the application of mathematics to ventilation, but they also in-elude examples of instances where arithmetic cannot be conveniently applied, and important estimates, based on judgment compounded of experience and a knowledge of the theoretical consideration involved, must be made. The inclusion of such estimates is intended as a guide and a warning to the reader; a guide in assisting him to recognize and estimate his own incalculables; and a warning that the solutions must not be blindly applied to his apparently similar problems. These sample calculations are intended to assist the reader in applying the theory contained in the standard texts on metal-mine ventilation. They have been selected from the ventilation experience of a British Columbia mine.

Jan 1, 1942

By C. Schlumberger

INTRODUCTION The object of the present paper is to discuss, from a geological point of view, the practical results obtained by the authors with the method of the &apos;resistivity map of the subsoil&apos; in the study of various mining problems. Some of the studies described date from 1920, 1922, and 1923. They are, therefore, quite old, at least as far as geophysical research is concerned (1). Others, on the contrary, are very recent (2). We shall deal only very briefly with the theoretical and technical sides of the processes employed. This paper has, essentially, a practical purpose, and it has seemed unnecessary to enter into a detailed discussion of the methods. Such a discussion cannot be presented without introducing ,quite. Complex considerations both of mathematics and experimental physics, which interest only the geophysicist: whose work is highly specialized.

Jan 1, 1931